TESTO ITC KORINNA 28mm Allargato
MONOBLOCK DIRECTIONAL
CONTROL VALVE
SD5
2 DAU003E
Simple , compact and heavy duty designed monoblock valves from 1 to 7 sections for open and closed centre hydraulic systems..
H Fitted with a main pressure relief valve and a load check valve.
H Available with parallel, series or tandem circuit.
H Optional carry--over port (only for parallel or tandem circuit).
H Diameter 16 mm -- 0.63 in interchangeable spools.
H A wide variety of service port valve options.
H Actuation is manual, pneumatic, electro--pneumatic, hydraulic, electro--hydraulic, with solenoid and remote with flexible cables
spool control kits.
Features
WARNING!
All specifications of this catalogue refer to the standard product at this date.
Walvoil, oriented to a continuous improvement, reserves the right to
discontinue, modify or revise the specifications, without notice.
WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN
INCORRECT USE OF THE PRODUCT.
3
rd
edition September 2012:
This edition supercedes all prior documents.
Additional information
This catalogue shows the product in the most standard configurations.
Please contact Sales Dpt. for more detailed information or special request.
SD5
3DAU003E
Contents
Working condition 4.................................
Performance data 5..................................
Directional valve with left inlet 7......................
Directional valve with right inlet 77....................
Installation and maintenance 126.....................
Accessories 129.....................................
Working conditions
Standard threads
SD5
4 DAU003E
This catalogue shows technical specifications and diagrams measured with mineral oilof 46 mm
2
/s -- 46 cSt viscosity at 40C tempera-
ture.
Nominal flow rating
45 l/min
Operating pressure (max.) parallel pr tandem circuit 315 bar 4600 psi
series circuit 250 bar 3600 psi
Max. back pressure on outlet port T 25 bar 360 psi
Internal leakage A(B)T
p=100 bar -- 1450psi with fluid and valve at 40
C 3cm
3
/min 0.18 in
3
/min
Hydraulic fluid Mineral base oil
Fluid temperature with NBR seals from --20 to 80C
with FPM seals from --20 to 100C
Viecosity operating range from 15 to 75 mm
2
/s from 15 to 75 cSt
minimum 12 mm
2
/s 12 cSt
maximum 400 mm
2
/s 400 cSt
Max. level of contamination 19/16 -- ISO 4406
A
m
b
i
e
n
t
t
e
m
p
e
r
a
t
u
r
e
with mechanical, pneumatic and hydraulic devices from --40 to 60C
A
m
b
i
ent temperature
with electric devices
from --20 to 60C
NOTE -- For different conditions please contact Sales Dept.
REFERENCE STANDARDS
BSP UN--UNF METRIC NPTF
THREAD
A
C
C
O
R
D
I
N
G
T
O
ISO 228/1 ISO 263 ISO 262 ANSI B1.20.3
ACCORDING TO
BS 2779
ANSI B1.1 unified
CAVITY
A
C
C
O
R
D
I
N
G
T
O
ISO 1179 11926 9974--1
ACCORDING TO
SAE
J1926 J2244 J476a
DIN 3852--2
shape X o Y
3852--1
shape X o Y
PORTS THREAD
MAIN PORTS BSP UN--UNF METRICA
IInlet P and carry --over C
G3/8 3/4--16 (SAE 8) M18x1,5
Ports A and B G3/8 9/16--18 (SAE 6) M18x1,5
Outlet T
G3/8
G1/2
*
3/4--16 (SAE 8)
M18x1,5
M22x1,5
*
CONTROL PILOT PORTS
Pneumatics NPTF 1/8--27 NPTF 1/8--27 NPTF 1/8--27
Hydraulics G1/4 9/16--18 (SAE 6) G1/4
(*)--Only for series circuit..
Performance data (pressure drop vs. flow)
0
10
20
30
40
0 15304560
A
1
(B
1
)T
Flow
Pressure drop
540
360
180
(l/min)
(bar)
(psi)
0
10
20
30
40
0 15304560
Flow
Pressure drop
540
360
180
(l/min)
(bar)
(psi)
0
10
20
30
40
0 15304560
Flow
Pressure drop
540
360
180
(l/min)
(bar)
(psi)
Work port to outlet
Inlet to work port
Open centre
A1 A2 A3
B1 B2 B3
P
T
A4 A5 A6
B4 B5 B6
B7
A7
From side inlet to side outlet.
From side inlet to A port (spool in position 1)orB port (spool in position 2).
From A port (spool in position 2)orB port (spool in position 1) to side outlet.
NOTE -- Measured with spool type 1.
A1 A2 A3
B1 B2 B3
P
T
A4 A5 A6
B4 B5 B6
B7
A7
A1 A2 A3
B1 B2 B3
P
T
A4 A5 A6
B4 B5 B6
B7
A7
2 sections
4 sections
7 sections
PA
7
(B
7
)
PA
1
(B
1
)
A
7
(B
7
)T
SD5
5DAU003E
SD5
6 DAU003E
SD5
7DAU003E
Contents
Directional valve with parallel circuit
Dimensional data 8...................................
Hydraulic circuit 9....................................
Ordering codes 10....................................
Inlet relief options 12..................................
Spools 13...........................................
“A” side spool positioners 20..........................
“B” side options 39...................................
Complete controls 44.................................
Outlet port options 49.................................
Service and auxiliary valves
ordering codes 52.................................
port relief valves 54................................
pilot check valves 56..............................
flange mounted relief valves 55.....................
antishock valves 57...............................
fixed setting antishock and anticavitation valves 59.....
adjustable setting antishock and anticavitation valves 61
flow control valves 65..............................
Other execu tio n s
Main features 69.....................................
Directional valve SD5/1--N 70..........................
Directional valve SD5/1--D 71..........................
Directional valve SD5 --S with series circuit 72............
Directional valve SD5--SP with tandem circuit 74..........
Dimensional data (parallel circuit)
WALVOIL
SD5/2--P
P0500001
1022004092
MADE IN ITALY
30 37
51
81
34
186
103
45
12,5
11,5
23
45,5
27
M8
20
90
24,5
45
63,5
5
8,5
20,5
Carry--over
F
E
WALVOIL
SD5/2--P
P0000001
102219002
MADE IN ITALY
Valve code
Production batch:
P05 = production year (2005)
00001 = progressive number
Valve type
0.06
7.32
1.34
1.791.77
0.91
1.18
1.46 1.06
0.79
0.45
2.01
3.19
4.06
0.81
0.33
2.50 0.20
1.77
3.54
0.96
15
15
1
2
0
24
24
spool out
3
3
spool in
SD5 directional valve with left inlet
8 DAU003E
T
Y
P
E
E F Weight
T
Y
P
E
E F Weight
T
Y
P
E
mm in mm in kg lb
T
Y
P
E
mm in mm in kg lb
SD5/1--P
100.5 3.96 73 2.87 3.5 7.7
SD5/5--P
248.5 9.78 221 8.70 10.1 22.3
SD5/2--P
137.5 5.41 110 4.33 5.2 11.5
SD5/6--P
285.5 11.24 258 10.16 11.7 25.8
SD5/3--P
174.5 6.87 147 5.79 6.9 15.2
SD5/7--P
322.5 12.70 295 11.61 13.2 29.1
SD5/4--P
211.5 8.33 184 7.24 8.1 17.9
Parallel
Hydraulic circuit
Standard configuration with side inlet and outlet and open centre (AET execution).
Main relief valve
Lever pivot box
Check valve
Allenwrench4
24 Nm / 17.7 lbft
Configuration with upper inlet and outlet
P
A1 B1 A2 B2
T
Description example:
SD5/2--P(JG3--120)/18L/18L/AET-- PSA
P
A1 B1 A2 B2
T
Description example
SD5/2--P(JG3--120)/18L/18L/AET
Standard configuration
Tank line
Flow through
(LC)
Pressure line
Port A line
Port B line
Positioner kit
Plug for open centre
Allenwrench8
24 Nm / 17.7 lbft
A
B
T
P
120
1750
120
1750
directional valve with left inlet SD5
9DAU003E
SD5 directional valve with left inlet
10 DAU003E
2. Inlet relief options page 12
1. Body kits *
Ordering codes3.
2.
2.
SD5 / 2 -- P (JG3--120) / 1 8 L / 1 8IM . P3(G3--100) / AET *
TYPE CODE DESCRIPTION
1--P 5KC1 193000 Parallel, 1 section
2--P 5KC1223000 Parallel, 2 sections
3--P 5KC1243000 Parallel, 3 sections
4--P 5KC1273000 Parallel, 4 sections
5--P 5KC1313000 Parallel, 5 sections
6--P 5KC1353000 Parallel, 6 sections
7--P 5KC13E3000 Parallel, 7 sections
TYPE CODE DESCRIPTION
VMD5 direct pressure relief valve type J
Standard setting is referred to 10 l/min flow .
(JG2--63) 5KIT105412 Range 40 to 63 bar / 580 to 900 psi
standard setting 63 bar / 900 psi
(JG3--120) 5KIT105413 Range 50 to 200 bar / 725 to 2900 psi
standard setting 120 bar / 1750 psi
(JG4--220) 5KIT105414 Range 160 to 315 bar / 2300 to 4600 psi
standard setting 220 bar / 3200 psi
SV XTAP623282 Relief valve blanking plug
4. 5.
Include boby, seals and load check valve.
1
st
section following section
1.
Description examp le:
II
5.
4.
I
8.
9.
1.
3.
3. Spool options page 13
TYPE CODE DESCRIPTION
1 3CU1210130 Double acting, 3 positions, with A and B
closed in neutral position
1A 3CU1221130 Double acting, 3 positions, with A open to
tank in neutral position
1B 3CU1222130 Double acting, 3 positions, with B open to
tank in neutral position
2 3CU1225130 Double acting, 3 positions, with A and B
open to tank in neutral position
2H 3CU1225225 Double acting, 3 positions, with A e B
partially open to tank in neutral position
3 3CU1231130 Single acting on A, 3 positions, B plugged
requires G3/8 plug (see part I )
Special spools for particular positioner kits
5DY 3CU1242220 Double acting, 4 positions, floating circuit
in 4
th
position with spool in
5PY 3CU1245620 Double acting, 4 positions, floating circuit
in 4
th
position with spool out, with check
valve
8 3CU1262120 Double acting, 4 positions, regenerative
circuit in 4
th
position with spool in
Special spools for standard positioner kits
8F 3CU1261100 Double acting, 3 positions, regenerative
circuit in 2
nd
position with spool out
NOTE (*) -- Codes are referred to BSP threads.
7.
7.
3.
6. 8.
6.
Valve setting (bar)
Valve setting (bar)
directional valve with left inlet SD5
11DAU003E
7. Service valves page 52
I ”A” and “B” ports plugs *
II Optional handlevers
9. Inlet and outlet selection * page 9
4. “A” side spool positioners page 20
Ordering codes
TYPE CODE DESCRIPTION
8 5V08105000 With spring return in neutral position
8D 5V08105200 With spring return in neutral position and
pin with M6 female thread for dual control
8D2 5V08105220 With spring return in neutral position and
pin with M8 male thread for dual control
8F2 5V08105101 With spring return in neutral position and
adjustable flow limiter
19 5V19105000 2 positions, with spring return in neutral
position from position 1
20 5V19105000 2 positions, with spring return in neutral
position from position 2
9 5V09105010 With detent in position 1 and spring return
in neutral position
10 5V10105010 With detent in position 2 and spring return
in neutral position
11 5V11105000 Detent in positions neutral, 1 and 2
12 5V12105000 Detent in positions 1 and 2
15 5V15105000 2 positions, detent in positions 1 and
neutral
16 5V16105000 2 positions, detent in positions 2 and
neutral
9BZ 5V09202010 With detent in position 1 and spring return
in neutral position
10BZ 5V10202010 With detent in position 2 and spring return
in neutral position
11B Z 5V11202010 Detent in positions 1 and 2 and spring
return in neutral position
8K 5V08705112 With spring return in neutral position and
12 VDC spool solenoid lock device
5V08705124 As previous, 24VDC
8RM2 5V08105590 With spring return in neutral position and
12VDC electromagnetic detent in pos. 2
5V08105595 As previous, 24VDC
8MHE3(NC) 5V08105541 With spring return in neutral position and
spool postioning ON/OFF electric signal
circuit normally closed
8MHE3(NO) 5V08105540 As previous, with circuit normally open
8MS3 5V08105553 With spring return in neutral position,
operation signalling in position 1 and 2,
prearranged for centralized microswitch
control: need KM connection kit
8MG3(NO) 5V08105660 With spring return in neutral position and
microswitch in positions 1 and 2
8P 5V08105701 ON/OFF pneumatic kit
8EP3 5V08105735 ON/OFF 12 VDC electro--pneumatic kit
5V08105740 ON/OFF 24 VDC electro--pneumatic kit
8ED3 5V08105350 ON/OFF 12 VDC electro--hydraulic kit
5V08105351 ON/OFF 24 VDC electro--hydraulic kit
TYPE CODE DESCRIPTION
PSL 3XTAP722160 Side ports; need n.2 G 3/8 plugs, standard
configuration (omit in valve description)
PSA 3XT AP722160 Upper ports; need n.2 G 3/8 plugs
TYPE CODE DESCRIPTION
AL01/M8x120 170011012 For lever L: height 120 mm / 4.72 in
AL01/M10x150 170012015 For lever LM10:
height 150 mm / 5.91 in
AL08/M12x150 170013115 For joystick LCB:
height 150 mm / 5.91 in
TYPE CODE DESCRIPTION
G3/8 3XTAP722160 for single acting spool type 3
Port relief, anti--shock, pilot operated check and flow regulation valves.
6. Complete controls page 44
Proportional hydraulic control type 8IM and ON/OFF solenoid controls
type 8ES and 8ESN.
5. “B” side options page 39
TYPE CODE DESCRIPTION
L 5LEV105000 Standard lever box
LM10 5LEV205000 Lever box for M10 handlever
LF1 5LEV105102 Lever box with adjustable flow limiter
LEB 5LEV605000 Safety lever box, vertical configuration
LUP 5LEV805005 Safety lever box, horizontal configuration
SLP 5COP105000 Without lever box, with dust--proof plate
SLC 5COP205000 Without lever box, with endcap
TQ 5TEL105110 Flexible cable connection
LCB 5CLO205100 Joystick lever for 2 sections operation
4. “A” side spool positioners
Particular positioner kits for special spools page 36...............
13NZ 5V13305010 4 pos. with spring return in neutral pos.
and detent in 4
th
pos.: for spool 5DY
13QN 5V13405020 4 pos. with spring return in neutral pos.
and detent in 4
th
pos.: for spool 5PY
13FZ 5V13505400 4 positions with spring return in neutral
position: for spool 8
13QNMG3(NO) 5V13405660 As type 13QN with microswitch in
positions 1 and 2: for spool 5PY
8. Outlet port option page 49
TYPE CODE DESCRIPTION
AET XTAP623170 Open centre plug
AEK 3XTAP522282 Closed centre plug
AE 3XGIU522460
* G3/8 carry--over sleeve
AET--L XCAR405300 With hydraulic pilot unloader valve
AET--LT XTAP523370 Unloader valve blanking plug
Electric control unloader v a l v e
: for valves and coils list see page 50.
0
100
200
300
400
0 204060
0
100
200
300
400
0204060
Direct pressure relief vave
Inlet relief options
Spring nr. 4 (red band)Spring nr. 3 (blue band)Spring nr. 2 (green band)
0
100
200
300
400
0204060
Flow
Pressure
(l/min)
(bar)
Flow
Pressure
(l/min)
(bar)
Flow
Pressure
(l/min)
(bar)
0,05”
TIME RESPONSE
10%
100 bar
90%
95%
105%
Pressure
Time (”)
(% P)
Time response
VMD5 ( J G 3 -- 120 )
Standard setting in bar (for value see page 8)
Performance data
Adjustment type
Adjustment type (G, H)
Adjustable spring type (2,3,4).
G: with screw H: valve set and locked
59.5max. 51.5
SV: relief valve blanking p lu g
Wrench 19
42 Nm / 31 lbft
Wrench 13
24 Nm / 17.7 lbft
Allenwrench4
Allenwrench10
42 Nm / 31 lbft
Cap code: 3COP117260
2.03 2.34
(psi)
4500
3000
1500
(psi)
4500
3000
1500
(psi)
4500
3000
1500
1450 psi
SD5 directional valve with left inlet
12 DAU003E
F
J
Y
P
(on ports)
= 63bar / 900 psi
P
(on ports)
= 100bar / 1450 psi
P
(on ports)
= 250bar / 3600 psi
Qin = 45 l/min
Type 1
Spool options
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke (mm)
(l/min )
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke
Spool metering A(B)TSpool metering PA(B)
(mm)
(l/min )
201
201
201
AB
PT
P--A--B--T closed, with flow through line (LC) open
A
"
P AB T
P BA T
Performance data
AB
PT
AB
PT
F
J
Y
F
J
Y
AB
TP LCT
AB
TP LCT
AB
TP LCT
142
20
29
10
5.5 5.5
0.39
0.35
0.79
5.59
(in)
0.1 0.2
(in)
0.1 0.2
For special requirement, spool 1CS code 3CU1210200 suggested for flow from 15 to 30 l/min and spool 1CEX code 3CU1210230
suggested for flow up to 15 l/min, are available.
stroke:
+5.5mm/0.22 in
stroke:
+5.5mm/0.22 in
directional valve with left inlet SD5
13DAU003E
Type 2
Type 1B
Type 1A
Spool options
201
AB
PT
Type 2H
201
AB
PT
201
AB
PT
201
AB
PT
AB
TP LCT
AB
TP LCT
AB
TP LCT
AB
TP LCT
P--B closed, AT, flow through line (LC) open
P--A closed, BT, flow through line (LC) open
P closed, A--BT, flow through line (LC) open
P closed, A--B partially open to tank,
flow through line (LC) open
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
SD5 directional valve with left inlet
14 DAU003E
F
J
Y
P
(on ports)
= 63bar / 900 psi
P
(on ports)
= 100bar / 1450 psi
P
(on ports)
= 250bar / 3600 psi
Qin = 45 l/min
A
"
A
PT
A
PT
201
A
PT
Type 3
Spool options
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke (mm)
(l/min )
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke
Spool metering ATSpool metering PA
(mm)
(l/min )
201
201
P--B--T closed, flow through line (LC) open
P A
A T
Performance data
F
J
Y
F
J
Y
A
TP LCT
A
TP LCT
A
TP LCT
Port B plugged
Allen wrench 6 -- 24 Nm / 17.7 lbft
5.5
5.5
(in)
0.1 0.2
(in)
0.1 0.2
stroke:
+5.5mm/0.22 in
stroke:
-- 5 . 5 m m / 0.22 in
directional valve with left inlet SD5
15DAU003E
0
5
10
15
20
0 15304560
Pressure
Flow (l/min)
(bar)
Pressure drop in position 3
(last section)
BT
AT
(psi)
200
100
0
20
40
60
0,0 1,0 2,0 3,0 4,0 5,0
Spool metering
Qin=45l/min/P
(on ports)
= 100 bar -- 1450 psi
Flow
Stroke (mm)
(l/min )
5.5
Performance data
(in)
0.1 0.2
PA
AT
PB
BT
AA
A
"
AB
TP LCT
AB
TP LCT
AB
TP LCT
Spools
Type 5DY
P B,A T
A-- B T (float in lock position)
201
201
201
201 3
3
3
3
AB
PT
AB
PT
AB
PT
AB
PT
P A,B T
It needs special body with extra machining: for information please contact Sales Deptartment.
This spool must be coupled with positioner type 13NZ (see page 36).
Also available spool with check valve on A port; type 5WY code 3CU1242320.
P-- A-- B-- T closed
flow through line (LC) open
AB
TP LCT
stroke:
+4.5mm/0.18 in
stroke:
-- 4 . 5 m m / 0.18 in
stroke:
-- 9 m m / 0.35 in
SD5 directional valve with left inlet
16 DAU003E
0
20
40
60
0,0 1,0 2,0 3,0 4,0 5,0
A
AB
TP LCT
It needs special body with extra machining: for information please contact Sales Department.
This spool must be coupled with positioner type 13QN (see page 36) and 13QNMG3 (see page 37).
Spools options
Type 5PY
P B,A T
013 2
AB
PT
013 2
AB
PT
013 2
AB
PT
013 2
AB
PT
P A,B T
P--A--B--T closed,
with flow through line (LC) open
AB
TP LCT
AB
TP LCT
AB
TP LCT
0
5
10
15
20
0 15304560
Pressione
Portata (l/min)
(bar)
Pressure drop in position 3
(last section)
A(B)T
Spool metering
Qin=45l/min/P
(on ports)
= 100 bar -- 1450 psi
Flow
Stroke (mm)
(l/min)
5.5
Performance data
(in)
0.1 0.2
(psi)
200
100
""
"
PA(B)
BT
AT
stroke:
-- 4 . 5 m m / 0.18 in
stroke:
+4.5mm/0.18 in
stroke:
+9mm/0.35 in
directional valve with left inlet SD5
17DAU003E
AA
A
"
AB
TP LCT
It needs special body with extra machining: for information please contact Sales Department.
This spool must be coupled with positioner type 13FZ (see page 37).
P B,A T
P A--B (regenerative)
201
201
201 3
3
3
AB
PT
AB
PT
AB
PT
P A,B T
Type 8
Spools
2013
AB
PT
P--A--B--T closed flow through line (LC) open
AB
TP LCT
AB
TP LCT
AB
TP LCT
Stroke
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
(mm)
(l/min )
5.5
(mm)
Spool metering
Qin=45l/min/P
(on ports)
= 100 bar -- 1450 psi
(in)
0.1 0.2
Pressure drop in positione 3
(last section)
Performance data
0
5
10
15
20
0 15304560
Pressure
Flow (l/min)
(bar)
PB
AB
PA(B)A(B)T
(psi)
200
100
stroke:
-- 7 . 5 m m / 0.30 in
stroke:
-- 4 . 5 m m / 0.18 in
stroke:
+4.5mm/0.18 in
SD5 directional valve with left inlet
18 DAU003E
201
AB
PT
Type 8F
Spool options
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke (mm)
(l/min )
201
201
AB
PT
A
"
Performance data
AB
PT
5.5
P--A--B--T closed flow through line (LC) open
P B,A T
It needs special body with extra machining: for information please contact Sales Department.
P A--B (regenerative)
0
5
10
15
20
0 15304560
Pressure
Flow (l/min)
(bar)
Pressure drop in position 1
(in first section)
PA
BA
PBAT
AB
TP LCT
AB
TP LCT
AB
TP LCT
stroke:
+5.5mm/0.22 in
stroke:
-- 5 . 5 m m / 0.22 in
Spool metering
Qin=45l/min/P
(on ports)
= 100 bar -- 1450 psi
0.1 0.2
(in)
(psi)
200
100
directional valve with left inlet SD5
19DAU003E
Allenwrench4
6.6 Nm / 4.9 lbft
36.5
84
40
1.57 1.44
3.31
36.5
1.44
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
D
D
E
C
C
E
0.1 0.2
(in)
40
20
(lbf)
-- 0 . 1-- 0 . 2 0
60
0
-- 4 0
-- 2 0
-- 6 0
With spring return in neutral position
”A” side spool positioners
8kit
8D kit
8D2 kit
201
201
M8
201
It’s supplied with standard spring type D (see force--stroke diagram) and available with lighter spring type C (8MC code:5V08205000)
or heavier type E (8ME code: 5V08405000).
Allenrench5
9.8 Nm / 7.2 lbft
Wrench 9
9.8 Nm / 7.2 lbft
M6
36.5
44
12
1.73
1.44
0.47
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 9
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Spool end joint code XPER315400, is available on request in order to screw onto pin.
10
40
18
20
4
M6
15
8
8
Spool end joint dimensions
0.16
0.39 0.79
0.31
0.71
1.57
0.31
0.59
SD5 directional valve with left inlet
20 DAU003E
201
36.5
1.44
With spring return in neutral position
“A” side spool positioners
8F2 kit
19 kit
M8x1
20
20 kit
--300
--200
--100
0
100
200
300
0123456
Stroke
Force
(mm)
(N)
Force --stroke diagram
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0
Stroke
Force
(mm)
(N)
Force --stroke diagram
51.5
2.03
36.5
1.44
Allenwrench4
6.6 Nm / 4.9 lbft
(in)
40
20
60
0
-- 4 0
-- 2 0
-- 6 0
(lbf)
0.1 0.2
(in)
40
20
60
0
-- 4 0
-- 2 0
-- 6 0
(lbf)
-- 0 . 1-- 0 . 2
01
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
Wrench 13
24 Nm / 17.7 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
36.5
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.44
directional valve with left inlet SD5
21DAU003E
Operating features
Locking and release force : 100 N / 22.5 lbf 10%........
36.5
1.44
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Operating features
Locking and release force : 100 N / 22.5 lbf 10%........
36.5
1.44
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Operating features
Locking and release force : 100 N / 22.5 lbf 10%........
36.5
Allenwrench4
6.6 Nm / 4.9 lbft
1.44
36,5
Allenwrench5
9.8 Nm / 7.2 lbft
Operating features
Locking and release force : 120 N / 27 lbf 10%........
36.5
1.44
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Operating features
Locking force (from pos. 0 to 2) : 150 N / 33.7 lbf 10%...
Release force (from pos. 2 to 0) : 140 N / 31.5 lbf 10%...
41
Allenwrench4
6.6 Nm / 4.9 lbft
1.61
Allenwrench5
9.8 Nm / 7.2 lbft
Operating features
Locking force (from pos. 0 to 1) : 150 N / 33.7 lbf 10%...
Release force (from pos. 1 to 0) : 140 N / 31.5 lbf 10%...
45,545.5
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.79
201201
201
With detent
”A” side spool positioners
9kit
11 kit
15 kit
10 kit
201
12 kit
01
20
16 kit
SD5 directional valve with left inlet
22 DAU003E
72.5
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
2.85
72.5
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
2.85
72.5
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
2.85
With detent and spring return to neutral position from either directions
“A” side spool positioners
9BZ kit
10BZ kit
11BZ kit
201
201
201
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
Locking force: 120 N / 27 lbf 10% / Release force: 230 N / 51.7 lbf 10%
Detent area
201
Port B Port A
3.3
0.22
-- 5 . 5
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
Locking force: 120 N / 27 lbf 10% / Release force: 230 N / 51.7 lbf 10%
Detent area
201
Port B Port A
-- 3 . 3
-- 5 . 5
5.5
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
Locking force: 120 N / 27 lbf 10% / Release force: 230 N / 51.7 lbf 10%
201
Port B Port A
-- 3 . 3
-- 5 . 5
5.5
3.3
Detent area
40
20
(lbf)
60
0
-- 4 0
-- 2 0
-- 6 0
0.1 0.2
(in)
-- 0 . 1-- 0 . 2 0
40
20
(lbf)
60
0
-- 4 0
-- 2 0
-- 6 0
0.1 0.2
(in)
-- 0 . 1-- 0 . 2 0
40
20
(lbf)
60
0
-- 4 0
-- 2 0
-- 6 0
0.1 0.2
(in)
-- 0 . 1-- 0 . 2 0
-0.22
40
20
60
0
-- 4 0
-- 2 0
-- 6 0
5.5
0.13
-0.13
-0.22
0.22
-0.19
-0.22
0.22
0.13
Detent area
directional valve with left inlet SD5
23DAU003E
Solenoid lock device type 8K
“A” side spool positioners
With spring return and spool electromechanical lock in neutral position; when coil is feeded the spool can be moved.
Operating features
ACTUATOR
Lock stroke : 3.5 mm / 0.14 in.....................
COIL
Depending on model: see following features
201
NOTE -- The kit control must be turned at 180
. when pilot
operated check valves are fitted.
Coil with ISO4400 connector
Coil with Deutsch DT connector
Nom. voltage tolerance : 10%........
Power rating : 18 W.................
Nominal current : 1.58 A -- 12 VDC...............
: 0.81 A -- 24VDC
Coil insulance : Class F................
Weather protection : IP65............
Duty cycle : 100%...................
Nom. voltage tolerance : 10%........
Power rating : 22 W.................
Nominal current : 1.9 A -- 12 VDC...............
: 0.95 A -- 24VDC
Coil insulance : Class H................
Weather protection : IP65............
Duty cycle : 100%...................
Coil with Packard M--Pack connector
Nom. voltage tolerance : 10%........
Power rating : 18 W.................
Nominal current : 1.58 A -- 12 VDC...............
: 0.81 A -- 24VDC
Coil insulance : Class F................
Weather protection : IP65............
Duty cycle : 100%...................
634
Wrench 24
9.8 Nm / 7.2 lbft
Wrench 10
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
22
71.5
112.5
Allenwrench4
6.6 Nm / 4.9 lbft
25
4.43
0.87
2.82
Allenwrench5
9.8 Nm / 7.2 lbft
SD5 directional valve with left inlet
24 DAU003E
COMPLETE CONTROLS CODES
CONNECTION TYPE
ISO4400 Deutsch DT Packard M--Pack
CONTROL TYPE
Voltage 8K 8K4 8K6
12 VDC 5V08705112 5V08705412 5V08705612
24 VDC 5V08705124 5V08705424 5V08705624
Need
connector
(see page 129)
C02 C19 C20
Solenoid lock device type 8K
“A” side spool positioner
It’s possible to obtain further configurations of complete control, using the K kit, coils and 3 positions “A” side spool positioner, as
following draw: for information contact Sales Department.
More configurations and spare parts
3 positions “A” side spool
positioner type 9B, 10B, 11B.
(see page 23)
Fitted with actuator:
code 5KIT810500
Coil
Kit K
directional valve with left inlet SD5
25DAU003E
COILS CODES
CONNECTION TYPE
Voltage ISO4400 Deutsch DT Packard M--Pack
12 VDC 2X4300012 2X4300014 YSOL300013
24 VDC 2X4300024 2X4300026 YSOL300025
Operating features
COIL
Nominal voltage : 12 / 24 VDC 10%...............
Power rating : 5,5 W..................
Resistance (20 C) : 26,5 / ??? Ohm.............
Min unlocking force : 45 N / 49.5 lbf.............
Duty cycle : 100%....................
Electromagnetic detent type 8RM2
“A” side spool positioners
108
With electromagnetic detent in position 2 and spring return to neutral position.
600
88.5
Wrench 11 -- 9.8 Nm / 7.2 lbft
Notch 1.2 mm / 0.047 in
6.6 Nm / 4.9 lbft
201
600 200
374
Coil with Deutsch DT
connection
Coil with AMP Fastin--Faston
connection
Coil with Packard M--Pack
connection
4.25
3.48
23.6
Allenwrench4--6.6Nm/4.9 lbft
Solenoid kit with connector
7.87
23.6
14.7
SD5 directional valve with left inlet
26 DAU003E
COMPLETE CONTROLS CODES
CONNECTION TYPE
Deutsch DT AMP Packard M--Pack
CONTROL DESCRIPTION
Voltage 8RM2 8RM2A(200)
12 VDC 5V08105590 5V08105591 5V08105593
24 VDC 5V08105595 5V08105596 5V08105598
Need
connector
(see page 129)
C19 C21 C20
COILS CODES
CONNECTION TYPE
Voltage Deutsch DT AMP Packard M--Pack
12 VDC YSOL532455 YSOL532452 YSOL532451
24 VDC YSOL532456 YSOL532458 YSOL532457
0
12
--6--5--4--3--2--10123456
Stroke
Voltage
(mm)
(VDC)
100%
Ouput signal with NO circuit
Tolerance range
0.1
0.20
-- 0 . 1
-- 0 . 2
Ouput signal with NC circuit
0
12
--6--5--4--3--2--10123456
Stroke
Voltage
(mm)
(VDC)
100%
Tolerance range
0.1
0.2 (in)0
-- 0 . 1
-- 0 . 2
44.5
81
38.5
Notch -- 6.6 Nm / 4.9 lbft
Wrench 10
9.8 Nm / 7.2 lbft
Wrench 5
6.6 Nm / 4.9 lbft
Wrench 5
9.8 Nm / 7.2 lbft
See view A
Connection DIN43650/C
(needs connector type C11, see page 129)
1.52
1.75
3.19
Operating features
Power supply range : from 3 da 28 VDC
Max. output current : 500 mA.
Weather protection : IP65.
41
32
Position 2
signal
Position 1
signal
Connector wiring
“A” side spool positioners
8MHE3 kit: with spring return in neutral position and spool positioning ON/OFF signal
201201
12 34
12 34
8MHE3(NC) kit 8MHE3(NO) kit
Configuration with
normally closed circuit
Configuration with
normally open circuit
This module supplies two different ON/OFF signals, related to the direction of the spool.
It has two separate contacts which c an be normallyopen or normally closed.
View A
View A
Mobile contact
Fixed contact
Mobile contact
Fixed contact
directional valve with left inlet SD5
27DAU003E
51 = with bracket for M51 (IP51) microswitch fixing
67 = with bracket for M67 (IP67) microswitch fixing
S = bracket placed on left
D = bracket placed on right
Assembling kit
Nr . of working sections
M3
n.2 threads
58
2.28
”A” side spool positioners
8MS3 kit: with centralized control for microswitch
P
A1 B1 A2 B2
T
Es.: SD5/2--P(JG3--120)/18MS3L/18MS3L/AET -- KM 2 S 51
120
Microswitch on
request (see page 25)
25.4
1
8
Rocker arm to
actuate microswitch
Allenwrench2.5
6.6 Nm / 4.9 lbft
Bracket for 5MIC100
microswitch
Allenwrench2.5
6.6 Nm / 4.9 lbft
1
0.04
0.32
1750
Assembly example
It’s shown an assembling on 2 section directional control valve, complete with connection kit KM.
SD5 directional valve with left inlet
28 DAU003E
1.5
0.06
27.1
58.2
33 6
2.29
1.30
0.24
Stroke
1.07
7
0.28
18 4
55.5
M4
2.19
0.71
4
0.16
21 4
64
M3
2.52
0.83
0.16
2.5
0.10
30.2
68
25.5 14
0.55
1.00
2.68
1.19
Stroke
6
0.24
Dedicated bracket is needed for the assembly
code: 3FLA225052
M51 c o de : 5 MIC100 M67 c o de : 5 MIC200
It’s complete with rubber cover and mounting screws: to order separately
58.3
2.29
8MS3 kit: with centralized control for microswitch
“A” side spool positioners
Microswitches for 8MS kits
Operating features
Max. current / voltage : 15 A / 480 V AC.............
:0.25A/250VDC
Weather protection : IP51...............
Operating features
Max. current / voltage : 5 A / 250 V AC.............
: 0.25 A / 230VDC
Weather protection : IP67...............
Allenwrench2.5
6.6 Nm / 4.9 lbft
Notch 1.5 mm / 0.06 in
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
201
201
201
8MS1 kit
microswitch operation in
position 1
Other configurations
8MS2 kit
microswitch operation in
position 2
8MS3 kit
microswitch operation in
positions 1 and 2
The spool positioner is composed of actioning pin 1 , bushes 2 and return spring 3.
The remaining items (cap, rocker arm, bracket , rod ecc..) are components of KM con-
nection kit, which depends on nr of controlled s ection.
KM kit ordering codes
The codes below represent the kit with bracket for IP51
microswitch, assembled on the left
For other codes or information contact Sales Department.
TYPE CODE DESCRIPTION
KM1S51 5KM1S5102 Kit for 1 section
KM2S51 5KM2S5102 Kit for 2 sections
KM3S51 5KM3S5102 Kit for 3 sections
KM4S51 5KM4S5102 Kit for 4 sections
KM5S51 5KM5S5102 Kit for 5 sections
KM6S51 5KM6S5102 Kit for 6 sections
KM7S51 5KM7S5102 Kit for 7 sections
1
3
2
directional valve with left inlet SD5
29DAU003E
PACKARD W--PACK
male connector with
female end
PACKARD W--PACK
female connector
with male end
Operating features
MICROSWITCH
Mechanical life : 5x10
5
operations...........
Electrical life (resistive load) : 10
5
oper. -- 7A / 13.5VDC
:5x10
4
oper. -- 10A / 12VDC
:5x10
4
oper. -- 3A / 28VDC
201
8MG1(NO) kit
201
201
Other configurations
8MG2(NO) kit
8MG3(NO) kit
With microswitch type 8MG3(NO)
“A” side spool positioners
With spring return in neutral position and microswitch operated in both directions.
Also available 8MG1 (NO) configuration (microswitch operated in position 1) and 8MG2(NO) configuration (microswitch operated in
position 2); dimensions are the same of 8MG3 configuration.
Same configurations are available with normally closed (NC) contact.
66,5
Wrench 22
42 Nm / 31 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4--6.6Nm/4.9 lbft
Microswitch with connector
With NO contact
code: 4MIC730
With NC contact
code: 4MIC740
It’s possible to obtain further configurations of complete control, using the MG kit, microswitches and 3 positions “A” side spool posi-
tioner, as following draw.
Kit MG
Microswitch
3 positions “A” side spool
positioner type 9B, 10B, 11B.
(see page 23)
Kit MG3
code: 5KIT820500
Kit MG1
code: 5KIT820501
Kit MG2
code: 5KIT820502
More configurations and spare parts
84,5 128
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 10
9.8 Nm / 7.2 lbft
3.33 5.04
SD5 directional valve with left inlet
30 DAU003E
COMPLETE CONTROLS CODES
CONTROL TYPE
Need
Contact 8MG3 8MG2 8MG1
N
e
e
d
connector type
NO
5V08105660 5V08105680 5V08105670 C07
see page
NC 5V08105662 5V08105682 5V08105672 C17
s
e
e
p
a
g
e
129
Operating features
Pilotpressure :min.5.5bar/80 psi...................
: max. 10 bar / 145 psi
118
23
4.64
0.91
51.5
V1
V2
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 10
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 11
9.8 Nm / 7.2 lbft
NPT 1/8” -- nr.2 thread
ON/OFF pneu matic kit type 8P
“A” side spool positioners
201
V1 V2
With spring return to neutral position.
2.03
directional valve with left inlet SD5
31DAU003E
V1 V2
Wrench 14 -- 9.8 Nm / 7.2 lbft
Special wrench -- 9.8 Nm / 7.2 lbft
Allenwrench4--6.6Nm/4.9 lbft
Wrench 13
24 Nm / 17.7 lbft
Wrench 9
Allenwrench4
6.6 Nm / 4.9 lbft
119
57
42
113.5
Pg9
43
1.69 2.24
4.47
1.65
4.68
6
Ø
0.24
ON/OFF electropneumatic kit type 8EP3
“A” side spool positioners
Operating features
CONTROL
Pilot pressure : 6 bar / 87 psi..............
: (max.10 bar / 145 psi)
COIL
Nominal voltage tolerance : 10%....
Power rating : 8 W...............
Nominal current : 0.67 A -- 12 VDC.............
: 0.33 A -- 24VDC
Coil insulation : Class F..............
Weather protection : IP65..........
Duty cycle : 100%.................
Coil with ISO6952
connector
Coil with flying leads
200
Scheme ISO 1219
Scheme
201
V1 V2
201
V1 V2
7.87
SD5 directional valve with left inlet
32 DAU003E
COMPLETE CONTROL CODES
CONNECTION TYPE
ISO6952 Flying leads
CONTROL TYPE
Voltage 8EP3 8EP35
12 VDC 5V08105735 5V08105736
24 VDC 5V08105740 5V08105741
Need
connector type
(see page 129)
C01
(compreso)
/
COIL CODES
V
o
l
t
a
g
e
CONNECTION TYPE
V
o
l
tage
ISO6952 Flying leads*
12 VDC 2X4000013 2XB1000120000
24 VDC 2X4000025 2XB1000240000
* Several type of connectors can be wired on request
directional valve with left inlet SD5
33DAU003E
COMPLETE CONTROL CODES
CONNECTION TYPE
I
S
O
4
4
0
0
AMP JPT
D
e
u
t
s
c
h
D
T
I
S
O
44
0
0
without diode with diode
D
eutsc
h
D
T
CONTROL TYPE
Voltage 8ED3 8ED32 8ED32D 8ED34
12 VDC 5V08105350 5V08105250 5V08105280 5V08105450
24 VDC 5V08105351 5V08105251 5V08105281 5V08105451
Need
connector type
(see page 129)
C02 C08 C08 C19
ON/OFF electrohydraulic kit type 8ED3
“A” side spool positioners
With external pilot and drain.
Scheme ISO 1219
Scheme
201
201
VL
L
V
1
Operating features
CONTROL
Pilotpressure :min.10bar/145 psi...................
: max. 50 bar / 725 psi
Max backpressure on drain L : 25 bar
/ 360 psi......
COIL
Nominal voltage tolerance : 10%.........
Power rating : 21 W....................
Nominal current : 1.75 A -- 12 VDC / 0.87 A -- 24VDC..................
Coil insulation : Class F...................
Weather protection : IP65...............
Duty cycle : 100%......................
Collector
116
133
Solenoid valve:
wrench 24 -- 9.8 Nm / 7.2 lbft
Coil
59
42
6.6 Nm
4.9 lbft
Allenwrench4--6.6Nm/4.9 lbft
Special wrench -- 9.8 Nm / 7.2 lbft
Wrench10--24Nm/17.7 lbft
Wrench 10
133
139
Allenwrench4--6,6Nm/4.9 lbft
5.47
1.65 2.32
5.24
4.57
5.24
SD5 directional valve with left inlet
34 DAU003E
COIL CODES
CONNECTION TYPE
I
S
O
4
4
0
0
AMP JPT
D
e
u
t
s
c
h
D
T
Voltage
I
S
O
44
0
0
without diodo with diodo
D
eutsc
h
D
T
12 VDC 2XB1400121 100 2XB1400121200 2XB1400121210 2XB1400120400
24 VDC 2XB1400241 100 2XB1400241200 2XB1400241210 2XB1400240400
COLLECTOR KIT CODES
Type Code * Description
KE1S0 5KE1S00030 Kit one section
KE2S0 5KE2S00230 Kit for 2 sections
KE3S0 5KE3S00230 Kit for 3 sections
KE4S0 5KE4S00230 Kit for 4 sections
KE5S0 5KE5S00230 Kit for 5 sections
KE6S0 5KE6S00230 Kit for 6 sections
(*) codes are referred to BSP thread
ON/OFF electrohydraulic kit type 8ED3
“A” side spool positioners
Collector kit for external pilot and drain
Description example:
SD5/2--P(JG3--120)/18ED3L/18ED3L/AET--KE2S0--24VDC
V
20 bar
290 psi
L
Collector
P
T
149.5
P
A1 B1 A2 B2
T
120
V
L
Coil with
ISO4400 connection
Coil with
AMP JPT connection
Coil with Deutsch DT connection
170
6.69
5.89
1750
directional valve with left inlet SD5
35DAU003E
COLLECTOR KIT CODES
Tipo Code * Description
KE1R0 5KE1R30230 Kit one section
KE2R0 5KE2R30230 Kit for 2 sections
KE3R0 5KE3R30230 Kit for 3 sections
KE4R0 5KE4R30230 Kit for 4 sections
KE5R0 5KE5R30230 Kit for 5 sections
KE6R0 5KE6R30230 Kit for 6 sections
(*) Codes are referred to BSP thread
20
0.79
Wrench 22
24 Nm / 17.7 lbft
Wrench 22
42 Nm / 31 lbft
Pressure drop PT
0
10
20
30
40
0153045
Flow
Pressure
(l/min)
(bar)
400
200
(psi)
“A” side spool positioners
Collector kit with pilot and drain lines
The kit is made of collector, VRP pressure reducing valve and pipes.
Description example:
SD5/2--P(JG3--120)/18ED3L/18ED3L/VRC--KE2R3--24VDC
ON/OFF electrohydraulic kit type 8ED3
Operating features
VRP VALVE
Output pressure : 20 bar / 290 psi.................
Max flow : 8 l/min.......................
Filtering : 80 ........................
149.5
Inlet line
Drain
T
P
Collector
VRP Code:
2S100808V AL21
VRC backpressure
valve (not included)
Wrench 17
Wrench 19
24 Nm / 17.7 lbft
35
13628
Wrench 22
24 Nm / 17.7 lbft
P
A1 B1 A2 B2
T
120
VRP
VRC
VRC valve: code X003600010
Valve assembled on flow through passage provides pilot pressure to the actuator.
Allenwrench6
24 Nm / 17.7 lbft
Wrench 22
24 Nm / 17.7 lbft
5.89
1.10
5.35
1.38
1750
Detent area
Locking force: 360 N / 81 lbf 10%
Release force: 390 N / 87.7 lbf 10%
--400
--200
0
200
400
--5--4--3--2--10123456789
Stroke
Forza
(mm)
(N)
Force --stroke diagram
201
Port B Port A
3
-- 4 . 5
4.5
Floating
72.5
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 6
9.8 Nm / 17.7 lbft
Special body kit
Particular positioner kits for special spools
“A” side spool positioners
13NZ kit
Detent area
Locking force: 280 N / 63 lbf 10%
Release force: 300 N / 67.4 lbf 10%
201 3
Detent in 4
th
position with spool in:available only for spool type 5DY (see page 16).
13QN kit
--400
--200
0
200
400
--9--8--7--6--5--4--3--2--1012345
Stroke
Force
(mm)
(N)
Force --stroke diagram
201
Port B Port A
4.5
-- 4 . 5
3
Floating
72.5
Special body kit
Detent in 4
th
position with spool out:available only for spool type 5PY (see page 17).
2013
-- 6 . 8
6.8
(in)
60
30
(lbf)
-- 0 . 1-- 0 . 2 0
0
-- 6 0
-- 3 0
-- 0 . 3 0.1
-0.18
-0.27
0.27
2.85
60
30
(lbf)
0
-- 6 0
-- 3 0
(in)
0.1 0.20 0.3-- 0 . 1
-0.18
0.18
0.27
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 6
9.8 Nm / 17.7 lbft
2.85
SD5 directional valve with left inlet
36 DAU003E
directional valve with left inlet SD5
37DAU003E
COMPLETE CONTROL CODES CODICI MICROINTERRUTTORI DI RICAMBIO
Contact type Needs connector
type
5V13405660 NO C07
see page
5V13405661 NC C17
s
e
e
p
a
g
e
129
Particular positioner kits for special spools
”A” side spool positioners
Detent in 4
th
position with spool out, spring return to neutral position and microswitch operation in both directions.
The microswitch can be c onfigured with NO (normally open) or NC (normally closed) contact
Av ailable only for spool type 5PY (see page 17).
Operating features
MICROSWITCH
Mechanical life : 5x10
5
operations.............
Electric life (resistive load) : 10
5
operations -- 7A / 13.5VDC....
:5x10
4
operations -- 10A / 12VDC
:5x10
4
operations -- 3A / 28VDC
102.5
Wrench22--42Nm/31 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Microswitch with
connector
13QNMG3(NO) kit
Wrench 6
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 10 -- 9.8 Nm / 7.2 lbft
2013
Microswitch kit with NO contact
code: 4MIC730
Female PACKARD
W--PACK connector
with male ends
Microswitch kit with NC contact
code: 4MIC740
Male PACKARD
W--PACK connector
with female ends
13FZ kit
72.5
Special body kit
201 3
4
th
position with spool in and spring return to neutral position.
Av alable only for spool type 8 (see page 18).
--400
--200
0
200
400
-- 8 -- 7 -- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5
Stroke
Force
(mm)
(N)
Force --stroke diagram
20 1
Port B Port A
4,5
7,5
3
Regenerative
4,5
84.5 128
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 6
9.8 Nm / 17.7 lbft
2.85
(in)
60
30
(lbf)
-- 0 . 1-- 0 . 2 0
0
-- 6 0
-- 3 0
-- 0 . 3 0 . 1
4.04
3.33
5.04
”A” side spool positioners
The positioners for special s pools (13NZ, 13QN, 13FZ), are also available with spool electromechanical lock in neutral position; if
coil is excited the spool can be operated.
For kit K and coils features and dimensions, see page 24: for informations contact Sales Department.
Particular positioner kits for special spools
With electromechanical lock
Special body kit depending
on used spool: for informa-
tion contact Sales Depart-
ment.
Coil
Kit K
13NZ positioner kit
(see page 36)
for spool type 5DY
13QN positioner kit
(see page 36)
for spool type 5PY
13FZ positioner kit
(see page 37)
for spool type 8
Complete actuator kit:
code 5KIT810500
SD5 directional valve with left inlet
38 DAU003E
CODICI BOBINE
CONNECTION TYPE
Voltage ISO4400 Deutsch DT Packard M--Pack
12 VDC 2X4300012 2X4300014 YSOL300013
24 VDC 2X4300024 2X4300026 YSOL300025
Need
connector type
(see page 129)
C02 C19 C20
20
44
1.73
0.79
Allenwrench2.5
Wrench 13
24 Nm / 17.7 lbft
20
44
24.5
20
53.7
65.5
66
max
M8
0.79
2.11
2.58
0.96
0.79
1.73
2.60
Allenwrench4--6.6Nm/4.9 lbft
M8
Type LM10
M10
201
M10
54
71.524.5
20
0.79
2.13
2.82
0.96
Allenwrench4
6.6 Nm / 4.9 lbft
NOTE (*) -- With spool type 5DY (see page 16)
(**) -- With spool type 5PY (see page 17)
29.2
41
1.15
1.61
Horizontal handlever
assembly
Allenwrench4
6.6 Nm / 4.9 lbft
M8
20
44
24.
20
53.7
65.5
1.73
0.79
0.79
2.11
2.580.96
5
(**) (*)
Vertical handlever
assembly
Lever co n t rol
”B” side options
Alluminium with protection boot lever pivot box; it can be rotated 180 (execution L180).
201
Execution L180
Type L
Type LF1
201
directional valve with left inlet SD5
39DAU003E
0.20
201
Special lever controls
“B” side options
Safety levers with lock in neutral complete with handlever; lift handlever knob to operate.
Type LEB
24.5 20
51.5
235
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 13
24 Nm / 17.7 lbft
Locking bush
5
Stroke for
lock release
52.8
20
To be used with body valves without auxiliary relief valves flanged on the working ports .
Av ailable with execution LEBS, code 5LEV605100, for configurations with auxiliary valves type BP and BPS: it operates floating
spool (4 positions) only by pulling the lever, with spool in (type 5DY).
6.7
Allenwrench4
6.6 Nm / 4.9 lbft
58.5
Wrench 13
24 Nm / 17.7 lbft
LEBSLEB
44
20
0.79
1.73
2.03
0.79
0.96
9.25
2.30
Stroke for
lock release
0.26
0.79
2.08
SD5 directional valve with left inlet
40 DAU003E
68.5
2.70
Allenwrench8
3Nm/2.2 lbft
Allenwrench4--6.6Nm/4.9 lbft
Type SLC
201
Protection cap usable with pneumatic,
electro--pneumatic, and electro --hy-
draulic spool positioners.
Av ailable as LUP(R150) configuration, with lenght L = 150 mm / 5.91 in and red knob: code 5LEV805010.
L = 219
52.8
53.7
12
M8
21
65
20
Stroke to unlocking
Locking bush
8.62
2.08
2.11
0.79
2.56
0.47
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 13
24 Nm / 17.7 lbft
0.83
Standard black knob
“B” side options
Controls arrangement
Special lever controls
Type LUP
15
9
22
9H8
0.35
0.87
0.59
0.35
+0.00866
0
201
Type SL Type SLP
201
Mechanical control with dust--proof
plate.
Allenwrench4
6.6 Nm / 4.9 lbft
8
0.32
directional valve with left inlet SD5
41DAU003E
81
Allenwrench4--6.6Nm/4.9 lbft
Wrench 10 -- 9.8 Nm / 7.2 lbft
Wrench24--24Nm/17.7 lbft
Flexible cable
3.19
“B” side options
Waterproof cap prearranged for remote control with flexible cable.
NOTE -- For more information about remote cable control, require appropriate documentation.
201
TQ cable remote control kit
NOTE -- For best efficiency, “A” side positioner with spring return type C is suggestedo (see page 20)
Connection example
SD5/2 directional control
valve without lever boxes
SCF031 remote control
CD flexible cable
TQ kit
SD5 directional valve with left inlet
42 DAU003E
NOTE -- Don’t use with spool type 5DY.
Execution LCB3
pivot placed above to the left
Exection LCB4
pivot placed above on the right
Execution LCB1
pivot placed down on the left
Execution LCB2
pivot placed down on the right
NOTE -- The handlever must be ordered separately (see page 11).
LCB mechan ical joystick for two sections control
201
201
Dimensions and movement scheme
B1
A2
A1
B2
B1--A2 B1--B2
A1--A2 A1--B2
A1
A2
B1
B2
A1--A2 A1--B2
B1--A2 B1--B2
A2
A1
B2
B1
A2--A1A2--B1
B2--A1
B2--B1
M12
1
st
section spool
2
nd
section spool
Pivot
Allenwrench5
9.8 Nm / 7.2 lbft
Wrench 10 -- 9.8 Nm / 7.2 lbft
Wrench13--24Nm/17.7 lbft
Wrench13--24Nm/17.7 lbft
Wrench 10
Wrench 13
24 Nm / 17.7 lbft
Allenwrench4--6.6Nm/4.9 lbft
Allenwrench4--6.6Nm/4.9 lbft
Execution LCB4
2
nd
section axis
1
st
section axis
10
27
0.39 1.06
B2
A1
A2
B1
B2--A1B2--B1
A2--A1
A2--B1
36
72
76
21.5
0.85
2.99
2.83
1.42
spool axis
1.5
36
1.42
0.06
“B” side options
directional valve with left inlet SD5
43DAU003E
4.
Complete controls14.
2.
3.
SD5 / 1 -- P (JG3--120) / 1 8ESN L ES / AET -- 24VDC
Description examp le:
2. 3.
5.
LES
CAE
4.1.
2. Spools options
TYPE CODE DESCRIPTION
1(ESN) 3CU1210036 Double acting, 3 positions, with A and B
closed in neutral position
2(ESN) 3CU1225036 Double acting, 3 positions, with A and B
open to tank in neutral position
3. Connection kit
TYPE CODE DESCRIPTION
8ESN 5V08009 For solenoid joint, with spring return in
neutral position
4. “B” side options
TYPE CODE DESCRIPTION
LES 5LEV105410 Safety lever pivot box for manual
operation
CAE 5COP205100 Endcap
5. Solenoid
TYPE CODE DESCRIPTION
10.5VDC XSOL314310 Nominal voltage 10.5VDC
12VDC XSOL314312 Nominal voltage 12VDC
24VDC XSOL314324 Nominal voltage 24VDC
192VDC XSOL314192 Nominal voltage 192VDC;
(for 220 VAC supply)
5.
1.
1. Body kit *
TYPE CODE DESCRIPTION
SD5/1--P 5KC1193100 1 section, standard body
SD5/2--PS 5KC1223003 2 sections, special body
SD5/3--PS 5KC1243006 3 sections, special body
NOTE (*) -- Codes are referred to BSPthreads.
8ESN solenoid control
Direct control by double solenoid with s pring return to neutral position, available with emergency manual override.
It’s necessary special spool and standard body (body kit without spool seals).
Due to the large dimension, it’s not possible to assembly more than one control consecutively, except SD5/2--P and SD5/3--P that
have special bodies with bigger centre--to--centre.
SD5 directional valve with left inlet
44 DAU003E
201
8ESNCAE kit
with encadp
201
8ESNLES kit
with safety lever pivot box
3
1
2
+--
P A
B T
P B
A T
Electric wiring example
To battery
Connector
Operating features
CONTROL
Internal leakage A(B)T
(p = 100 bar -- 1450 psi /T=40C) :max.10cm
3
/min -- 0.61 in
3
/min
COIL
Nominal voltage tolerance : 10%.........
Power rating : 65 W....................
Coil insulance : class H...................
Duty cycle : 100%......................
8ESN solenoid control
Complete controls
3112
WW
172.5
Spools: wrench 13
Allenwrench4
9.8 Nm / 7.2 lbft
Wrench 14
9.8 Nm / 7.2 lbft
Manual operation:
lift the bush to lever
unlocking
32
68.5
Wrench 24
24 Nm / 17.7 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
LES
CAE
Connection ISO4400
(needs C03 connector for VDC supply or C05
connector for V AC supply; see page 129)
6.79
2.70
Allenwrench4
6.6 Nm / 4.9 lbft
1.26
directional valve with left inlet SD5
45DAU003E
8ES solenoid control
Complete controls14.
Solenoid direct control with spring return to neutral position.
It needs special spools and standard body (body kit without seals on spool).
1.
2.
SD5 / 1 -- P (JG3--120) / 1 8ES3 4 / AET -- 24VDC
Description examp le:
1. 2.
8ES3
8ES1
3. 4.
4.
8ES3
8ES2
8ES1
8ES2
4.
2. Spool options
TYPE CODE DESCRIPTION
1(ES) 3CU121001 1 Double acting, 3 positions, with A and B
closed in neutral position
2(ES) 3CU1225010 Double acting, 3 positions, with A and B
open to tank in neutral position
3. Control kit
TYPE CODE DESCRIPTION
8ES1 5CAN08024 Single acting PA, with spring return to neutral
position
8ES2 5CAN08024 Single acting PB, with spring return to neutral
position
8ES3 5CAN08025 Double acting, with spring return to neutral position
4. Coils
TYPE CODE DESCRIPTION
With ISO4400 connector
10.5VDC 4SOL412012 Nominal voltage 10.5VDC
12VDC 4SOL412012 Nominal voltage 12VDC
24VDC 4SOL412024 Nominal voltage 24VDC
With Deutsch DT connector
4--10.5VDC 4SOL412111 Nominal voltage 10.5VDC
4--12VDC 4SOL412112 Nominal voltage 12VDC
4--24VDC 4SOL412124 Nominal voltage 24VDC
1. Body kit *
TYPE CODE DESCRIPTION
SD5/1--P 5KC1193100 1 section
SD5/2--P 5KC1223100 2 sections
SD5/3--P 5KC1243100 3 sections
SD5/4--P 5KC1273100 4 sections
SD5/5--P 5KC1313100 5 sections
SD5/6--P 5KC1353100 6 sections
SD5/7--P 5KC3E3100 7 sections
I
I ”A” and “B” ports plugs *
TYPE CODE DESCRIPTION
G3/8 3XTAP722160 For single acting controls type 8ES1 and
8ES2
NOTE (*) -- Codes are referred to BSP threads.
3.
3.
3.
3.
4.
SD5 directional valve with left inlet
46 DAU003E
8ES solenoid control
Complete controls
201
01
8ES3 kit
double acting
8ES3 kit
double acting
20
8ES3 kit
double acting
93.8
23.5
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 22
24 Nm / 17.7 lbft
7Nm/5.2 lbft
Spool
Emergency
manual override
Allenwrench4
6.6 Nm / 4.9 lbft
Coil with Deutsch DT connector
(needs connector C19: see page 129)
Coil with ISO4400 connector
(needs connector C02: see page 129)
0.93
3.69
0
100
200
300
400
0153045
Operating condition diagram
Flow
Pressure
(l/min)
(bar)
Operation area
(psi)
4500
3000
1500
Operating features
CONTROL
Internal leakage A(B)T
(p = 100 bar -- 1450 psi /T=40C) :max.15cm
3
/min -- 0.91 in
3
/min
COIL
Nominal voltage tolerance : 10%.........
Power rating : 36 W....................
Max. operating current : 3.43 A -- 10.5 VDC............
:3A--12VDC
: 1.5 A -- 24VDC
Weather protection : IP65 -- ISO4400 / P67 -- Deutsch DT...............
Coil insulance : class H...................
Insertion : 100%........................
P B
A T
P A
B T
+--
Electric wiring example
To battery
Connector 1
2
1
Connector 2
2
1
directional valve with left inlet SD5
47DAU003E
Spool control curve
type 026 with step
0
10
20
30
0,0 2,0 4,0 6,0
6.5
14
0.85
Pilot pressure
Stroke (mm)
(bar)
7.25
100
200
300
(psi)
(in)
400
Proportional hydraulic control type 8IM code 5IDR205021
Complete controls
201
VA VB
47.5
193
28
Allenwrench5
9.8 Nm / 17.7 lbft
VA VB
G1/4
42.5
Connection example
P
T
A1 A2
B1 B2
VA1 VA2
VB1 VB2
Hydraulic pilot control valve
series SVM400 with curve type 026
Pilot pressure -- stroke diagram
0
5
10
15
20
--6--4--20246
201
Port B Port A
Metering area
Spool overlap area
Pilot pressure
Stroke (mm)
(bar)
5.5
-- 5 . 5
0.1 0.2 (in)-- 0 . 1-- 0 . 2
100
200
(psi)
It can be used with standard s pools and body (body kit without seals on spool).
Coupling suggested with type 1CS spool (see page 13).
1.87
7.60
1.67
1.10
-- 5 . 5
--0.22
0.22
0.033
0.29
203
94
7.6
0.1 0.2
Operating features
Pilot pressure : max. 50 bar / 730 psi...........
Internal leakage A(B)T(p = 100 bar -- 1450 psi /T=40C)
:max.6cm
3
/min -- 0.37 in
3
/min........................
Allenwrench4 --6.6Nm/4.9 lbft
SD5 directional valve with left inlet
48 DAU003E
G3/8
C
20.5
Wrench22--42Nm/31 lbft
0.81
2.5
Allen wrench 8 --42 Nm / 31 lbft
0.1
10
G1/4
X
Wrench 24
42 Nm / 31 lbft
0.39
Operating features
Internal leakage : 10 cm
3
/min a 100 bar.................
: 0.61 in
3
/min at 1450 psi
0
3
6
9
12
0 10203040
Pressure drop curve
Flow
Pressure
(l/min)
(bar)
45
(psi)
150
100
50
It’s possible to have open centre, closed centre and carry--over.
Unloader valves are available: these valves need special bodies with appropriate cavity on lateral outlet port, the tank connection
T must be on top.
AE: with carry--over
AET: open centre (standard)
Outlet port options
See page 9.
Description example: SD5/2--P(KG3--120)/18L/18L/AE
P
A1 B1 A2 B2
T
120
Description example: SD5/2--P(KG3--120)/18L/18L/AEK
P
A1 B1 A2 B2
T
120
C
With hydraulic pilot unloader valve type L
For safety reasons it’s provided with pilot port plugged.
A2 B2
T
Description example:
SD5/2--P(JG3--120)/18L/18L/AET--L
X
AEK: closed cen t re
1750
1750
directional valve with left inlet SD5
49DAU003E
With solenoid pilot unloader valve
Outlet port options
For the complete valve must be ordered the cartridge and the coil both; to follow please see code list and description composi-
tion.
SD5 / 2 -- P (JG3--120) / 18L / 18L / AET--ELNW 4 (NC) -- 12VDC
1. 2.
1. Solenoid pilot unloader valve
TYPE CODE DESCRIPTION
AET--ELNW 0EFW0132002 Normally open, without emergency
AET--ELNW(NC) 0EFW0132003 As previous, normally closed
AET--ELTW 0EFW0132000 Normally open, with “push&twist”
emergency type
AET--ELPW 0EFW0132001 Normally open, with push--button
emergency type
2. Coil
TYPE CODE DESCRIPTION
With ISO4400 connection
12VDC 4SLE001200 Nominal voltage 12VDC
DB--12VDC 4SLE001217 As previous, with bi--directional diode
24VDC 4SLE002400 Nominal voltage 24VDC
DB--24VDC 4SLE002408 As previous, with bi--directional diode
With AMP JPT connection
2--12VDC 4SLE001203 Nominal voltage 12VDC
2DB--12VDC 4SLE001211 As previous, with bi--directional diode
2--24VDC 4SLE002403 Nominal voltage 24VDC
With Deutsch DT conenction
4--12VDC 4SLE001202 Nominal voltage 12VDC, parallel
connection
4DB--12VDC 4SLE001216 As previous, with bi--directional diode
4PD--12VDC 4SLE001201 Nominal voltage 12VDC,
perpendicular connection
4PDDB--12VDC 4SLE001209 As previous, with bi--directional diode
4--24VDC 4SLE002402 Nominal voltage 24VDC, parallel
connection
4PD--24VDC 4SLE002401 Nominal voltage 24VDC,
perpendicular connection
4PDDB--24VDC 4SLE002407 As previous, with bi--directional diode
2. 1.
Description example:
SD5/2--P(JG3--120)/18L/18L/AET --ELNW--12VDC
A2 B2
T
Description example:
SD5/2--P(JG3--120)/18L/18L/AET --ELNW(NC)--12VDC
A2 B2
T
Description examp le:
Example of directional valve with
normally open unloader valve
Example of directional valve with
normally closed unloader valve
SD5 directional valve with left inlet
50 DAU003E
A2 B2
T
Description example:
SD5/2--P(JG3--120)/18L/18L/AET --LT
Allenwrench6
24 Nm / 17.7 lbft
LT: unloader valve prearrangement
With solenoid pilot unloader valve
Outlet port options
Valve operating features
Max. flow : 45 l/min................
Max. pressure : 315 bar / 4600 psi............
Internal leakage (from 1 to 2) : max. 3 cm
3
/min at 100 bar
: max . 4.6 in
3
/min at 1450 psi
67
Wrench 24
42 Nm / 31 lbft
2
1
2
1
Type ELN
Type ELN(NC)
2
1
Type ELP
parallel type
ISO4400
connection
AMP JPT
connection
perpendicular type
Deutsch DT connection
0
5
10
15
20
25
0 5 10 15 20 25 30 35 40 45
Valve pressure drop
from 1 to 2 in open position
Flow
Pressure
(l/min)
(bar)
EL(NC)
EL(NA)
Coil operating features
Nominal voltage tolerance. : 10%
Power rating : 19.3 W -- 12 VDC...........
: 19.2 W -- 24 VDC
Max. operating current : 1.61 A -- 12 VDC...
: 0.80 A -- 24VDC
Coil insulation : Class H..........
Weather protection : IP65 -- ISO4400......
: IP69K -- Deutsch DT
:IP65--AMPJPT
Insertion : 100%...............
63 92.5
2
1
Type ELT
90.5
(psi)
300
200
100
2.64
2.48
3.56
3.64
directional valve with left inlet SD5
51DAU003E
SD5 directional valve with left inlet
52 DAU003E
Anti- shock + anti- cavitation valve (fixed setting)
Flow control valves
Anti- shock + anti- cavitation valve
Relef valve
Relef valve
Pilot check valves Anti- shock valve
5.
4.
1.
2.
3.
Srvice and au xiliary valves18.
6.
7.
BPS
BP
P
VS
Kit VM
VD13
All service and auxiliary valves need special body: contact Sales Department.
VD12
VD11
Kit VD1
VM(...)
VMT
VM(...)
VMT
VSC(JG...)
VSCT
Kit VS
Kit V
VP
VU
VC
VT
VP
VU
VC
VT
Mounting on the side
of working ports
Mounting on the opposite
side of working ports
directional valve with left inlet SD5
53DAU003E
3. Pilot check valves page 56
Supplied with mounting block
TYPE CODE DESCRIPTION
Directv
type
BP1 602002000
* Block with valve on port A
BP2 602002000
* Block with valve on port B
BP3 602002100
* Block with valves on ports A and B
BP XCAR605110 Single valve
With
pre--opening
BPS1 602003000
* Block with valve on port A
BPS2 602003000
* Block with valve on port B
BPS3 602003100
* Block with valves on ports A and B
BPS XCAR605210 Single valve
BPT XT AP627300 BP and BPS valves blanking plug
5. VM anti--schock+anti--cavitation valve page 59
Flange mounted type with fixed setting and fitted with mounting block.
TYPE CODE DESCRIPTION
VM(50) 5KIT326050 Setting 50 bar / 725 psi
VM(60) 5KIT326060 Setting 60 bar / 870 psi
VM(70) 5KIT326070 Setting 70 bar / 1010 psi
VM(80) 5KIT326080 Setting 80 bar / 1 150 psi
VM(90) 5KIT326090 Setting 90 bar / 1300 psi
VM(100) 5KIT326100 Setting 100 bar / 1450 psi
VM(125) 5KIT326125 Setting 125 bar / 1800 psi
VM(140) 5KIT326140 Setting 140 bar / 2050 psi
VM(160) 5KIT326160 Setting 160 bar / 2300 psi
VM(175) 5KIT326175 Setting 175 bar / 2550 psi
VM(190) 5KIT326190 Setting 190 bar / 2750 psi
VM(210) 5KIT326210 Setting 210 bar / 3050 psi
VM(230) 5KIT326230 Setting 230 bar / 3350 psi
VM(250) 5KIT326250 Setting 250 bar / 3600 psi
VM(260) 5KIT326260 Setting 260 bar / 3750 psi
VM(280) 5KIT326280 Setting 280 bar / 4050 psi
VM(300) 5KIT326300 Setting 300 bar / 4350 psi
VMT XTAP221340 Valve blanking plug
Kit VM 5CO2820020 Mounting block kit
Service and au xiliary valves
1. Relief valves page 54
TYPE CODE DESCRIPTION
VS(G3--100) 3XCAR505113 Range 40 to 200 bar / 580 to 2900 psi
standard setting 100 bar / 1450 psi
VST 3XTAP419300 Valve blanking plug
7. Flo w cont rol valves page 65
Flow control on every section; with auxiliary inlet
TYPE CODE DESCRIPTION
VD11 2S0PP10002000 Fine regulation from 3 to 30 l/min
VD12 2S163602021 1 As VD11, one turn with detent
VD13 2S0PP10002002 12VDC proportional solenoid valve
Kit VD1 5CO2822010
* Mounting block kit
2. Flange mounted relief valve page 55
TYPE CODE DESCRIPTION
VSC(JG2--60) 5KIT105412 Range 40 to 80 bar / 580 to 1150 psi
standard setting 60 bar / 870 psi
VSC(JG3--100) 5KIT105413 Range 63 to 200 bar / 900 to 2900 psi
standard setting 100 bar / 1450 psi
VSC(JG4--200) 5KIT105414 Range 160 to 250 bar / 2300 to 3600 psi
standard setting 200 bar / 2900 psi
VSCT XTAP623282 V alve blanking plug
Kit VS 5CO2420000 Mounting block kit
NOTE -- Valve setting at points 1--2--4--5--6 are referred to 10 l/min flow.
NOTE -- ( *) Codes are referred to BSP threads.
Set of valves fitted with mounting block.
TYPE CODE DESCRIPTION
Kit V 5CO2820010 Mounting block kit
T XTAP524280 V alve blanking plug
C 5KIT4061 10 Anti--cavitation valve
Anti--shock valves
P(G2) 5KIT206112 Range 60 to 125 bar / 870 to 1800 psi
standard setting 80 bar / 1150 psi
P(G3) 5KIT206113 Range 80 to 200 bar / 1150 to 2900 psi
standard setting 120 bar / 1750 psi
P(G4) 5KIT206114 Range 160 to 250 bar / 2300 to 3600 psi
standard setting 200 bar / 2900 psi
Anti--shock + anti--cavitation valves
U(G2) 5KIT3051 12 Range 40 to 100 bar / 580 to 1450 psi
standard setting 80 bar / 1150 psi
U(G3) 5KIT3051 13 Range 80 to 200 bar / 1150 to 2900 psi
standard setting 120 bar / 1750 psi
U(G4) 5KIT3051 14 Range 160 to 315 bar / 2300 to 4600 psi
standard setting 200 bar / 2900 psi
6. V anti--schock+anti--cavitation valve pag. 61
4. P antishock valves page 57
Cross return type, supplied with mounting block
TYPE CODE DESCRIPTION
P1(D3--100) 602001000
* Block with valve on port A
P2(D3--100) 602001000
* Block with valve on port B
P3(D3--100) 602001100
* Block with valves on ports A and B
P(D2--60) 5CAR211112 Single valve: range 40 to 100 bar / 580 to
1450 psi,standard setting 60 bar / 870 psi
P(D3--100) 5CAR211113 Single valve: range 80 to 200 bar / 1150
to 2900 psi, standard setting 100 bar /
1450 psi
P(D4--200) 5CAR211113 Single valve: range 180 to 315 bar / 2600
to 4600 psi, standard setting 200 bar /
2900 psi
PT XT AP526430 Valve blanking plug (for configuration P1,
P2)
4
0.16
VST: valve blanking plu g
Allenwrench6
42 Nm / 31 lbft
P
A1 B1 A2 B2
T
120
100
1450
1750
Hydraulic circuit
Description example:
SD5/2--P(KG3--120)/18L/VS(G3--100)/18L/AET --PSA
0,08”
TIME RESPONSE
10%
100 bar
90%
95%
105%
Pressure
Time (”)
(% P)
Time response
1450 psi
Spring nr. 3 (blue band)
0
100
200
300
400
0 102030
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
14
18.5 18.5
B1 B2
T
P
C
C
0.73
0.73
0.55
C--C
24.5
max.
G: with screw
H: valve set and locked
C--C
Adjustment type
Wrench 10
9.8 Nm / 7.2 lbft
Wrench 17
24 Nm / 17.7 lbft
Wrench 19
24 Nm / 17.7 lbft
Allenwrench3
0.96
Adjustment type (G, H)
VS ( G 3 -- 100 )
Pressure setting in bar (standard 100 bar / 1450 psi)
Spring type
It’s suggested for flow up to 25 l/min, and it’s mounted on parallel body to limitate the pressure, at lower value than main relief valve
(min. gap 20 bar / 290 psi ), on downstream section.
It’s in parallel with flow trough and it works only with single operation.
VS relief valve
Service and au xiliary valves
Performance data
SD5 directional valve with left inlet
54 DAU003E
13
32
max. 106
24.5
3454.5
Wrench 4
6.6 Nm / 4.9 lbft
2.15 1.34
max. 4.17
0.51
1.26 0.96
A1 A2
B1 B2
P
T
21.5
4337.5
53
37
1.48
1.69
0.85
2.09
1.46
P
A1 B1 A2 B2
T
120
1750
100
1450
Description example:
SD5/2--P(JG3--120)/18L/VSC(JG3 --100)/18L/AET
1
23
VSC relief valve
Service and au xiliary valves
VSC ( J G 3 -- 100 )
Adjustment type (G, H).
Adjustable spring type (2, 3, 4).
Standard setting in bar
(for value see page 53)
It’s flange mounted on parallel body on the opposite side of working ports, the function to limit the pressure, at lower value than main
relief v alve (min. gap 20 bar / 290 psi) on downstream sections.
It’s in parallel with flow through line and it works only with single operation.
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged (1) before the final honing of
spool hole, while the valve (3) is mounted during final assembling phase.
For information contact Sales Department.
NOTE -- For performance data, wrench
and tightening force, please see page 12.
directional valve with left inlet SD5
55DAU003E
BP valve pressure drop
0
10
20
30
40
0 204060
Flow
Pressure
(l/min)
(bar)
(psi)
450
300
150
0
10
20
30
40
0 204060
BPS valve pressure drop
Flow
Pressure
(l/min)
(bar)
(psi)
450
300
150
Performance data
Type
Pilot ratio
With
pre--opening
Main
BP
BPS 1:16
1:5.3
1:3.2
/
BP direct type
BPS with pre--opening
1 mounted on port A.
2 mounted on port B.
3 mounted on ports A and B.
BPS 1
BP3 configuration
Example of pressure on port A and port B to tank
BP1 configuration
Example of pressure on port A and port B to tank
AB
PT
Example of pressure on port B and port A to tank
AB
AB
Example of pressure on port B and port A to tank
PT
PT
BA
PT
Wrench 19
42 Nm / 31 lbft
Wrench 27
42 Nm / 31 lbft
Wrench 27
42 Nm / 31 lbft
BP, BPS pilot check valves
Service and au xiliary valves
BP1 BP2 BP3
A B
Cast iron block with pilot check v alves.
A B A B
BPS1 BPS2 BPS3
SD5 directional valve with left inlet
56 DAU003E
Performance data
0,12”
TIME RESPONSE
10%
120 bar
90%
95%
105%
Pressure
Time (”)
(% P)
Time response
1750 psi
Spring nr. 4 (red band)
0
100
200
300
400
0 204060
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
Spring nr. 3 (blue band)
0
100
200
300
400
0 204060
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
Spring nr. 2 (green band)
0
100
200
300
400
0 204060
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
P1 P2 P3
A BABAB
100
1450
100
1450
100
1450
100
1450
P an ti--shock valves with cross return
Service and au xiliary valves
Cast iron block with antishock valves.
P3 configuration
Example of pressure on port B and port A to tank
P1 configuration
Example of pressure on port A and port B to tank
AB AB
PT PT
Wrench 21
24 Nm / 17.7 lbft
Allenwrench5
Wrench 27
42 Nm / 31 lbft
Allenwrench8
42 Nm / 31 lbft
Adjustment with blind nut
(D).
Spring type (2,3,4).
P 1 ( D 3 -- 100 )
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
Standard setting in bar
(for value see page 43)
directional valve with left inlet SD5
57DAU003E
62.5
2.46
1.6
M5
10
13
0.39
0.51
16.5
0.65
2828 9 18.5
1.10
0.35
1.10
0.73
Milled surface with
fixing threaded holes
2737.5
1.06
1.48
Example of extra machining on directional valve body
36
1.42
16.521
14
50
19
60
26
37 273023 5.5
0.91
1.18 1.46 1.06 0.22
0.652.360.83
0.75
14
0.55
1.97
1.02
L1 special lever box
code: 5LEV105050
Standard lever box
BP3 configuration
valve block
P3 configuration
valve block
P3 configuration
BP3, BPS3 configuration
21.5
56.5
121.6
==
93
==
97
==
14.3
2.22
0.85
0.56
3.66
3.82
4.79
20 88
128
19
30
58
0.75
1.18
2.28
3.46
0.79
5.04
Mounting example for valves type P and BP, BPS
Service and au xiliary valves
SD5 directional valve with left inlet
58 DAU003E
27.5
40.5
14
86
13.5
24.5
5.5
3.39
0.550.22
0.53
1.08
1.59 0.96
A1 A2
B1 B2
P
T
15.3
36.621.9
53
37
0.86
1.44
0.60
2.09 1.46
1
23
Service and au xiliary valves
ValveonportB
ValveonportA
VM an ti--shock and anti--cavitatio n
They are flange mounted on the opposite side of working ports, connected in parallel with A and B ports and with outlet on T port.
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged on body (1) before the final
honing of spool hole, while the v alve (3) is mounted during final assembling phase.
For information contact Sales Department.
directional valve with left inlet SD5
59DAU003E
Allenwrench6
24 Nm / 17.7 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench10
24 Nm / 17.7 lbft
0
50
100
150
200
250
300
350
0 10203040
Pressure--flow diagram
Flow
Pressure
(bar)
(l/min)
45
(psi)
4500
3000
1500
VM1 VM2 VM3
AB
T
ABAB
TT
100
1450
100
1450
100
1450
100
1450
Valve setting in bar
1 mounted on port A
2 mounted on port B
3 mounted on ports A and B
VM 1 (100)
VM an ti--shock and anti--cavitatio n
Service and au xiliary valves
Example of VM1 configuration
SD5 directional valve with left inlet
60 DAU003E
P
57.5
32.5
2
2535
16
D
1.38 0.98
0.63
1.28
2.26
0.08
5.5 / 0.22
Dimension D value (mm / in)
VP VCVU VT
9.5 / 0.37
14 / 0.55
max.
14 / 0.55
max.
A1 A2
B1 B2
P
T
18
3622.5
53
37
1
0.89
1.42
0.71 0.04
2.09 1.46
1
2
Service and au xiliary valves
3
2
3
ValveonportBValveonportA
They are anti--shock (VP), anti--shock and anti--cavitation (VU) and anti --cavitation (VC) service valves, flange mounted on the
opposite side of working ports connected in parallel with A and B ports.
They need a dedicated body with extra machining: for production requirements, the blocks (2) are flanged on body (1) before the
final honing of spool hole, while the valves (3) are mounted during final assembling phase.
For information contact Sales Department.
V ant i--shock and anti--cavitation
directional valve with left inlet SD5
61DAU003E
0,02”
TIME RESPONSE
10%
100 bar
90%
95%
105%
Pressure
Time (”)
(% P)
Time response
1450 psi
0
100
200
300
400
0 204060
Spring nr.4 (red band)
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
0
100
200
300
400
0204060
Spring nr. 3 (blue band)
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
0
100
200
300
400
0 204060
Spring nr. 2 (green band)
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
Performance data
G: with screw H: valve set and locked
Adjustment type
Allenwrench5
9.8 Nm / 7.2 lbft
Wrench 22
42 Nm / 31 lbft
Notch
1.5 mm / 0.06 in
VP1 VP2
T A
100
B T
100
T A
100
B T
100
VP3
1450
1450 1450
1450
VP 1 ( G 3 -- 100 )
Adjustment type (G, H).
Spring type (2,3,4).
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
Standard setting in bar
(for value see page 53)
Anti--shock valve
V an ti--schock+anti--cavitation valves
Service and au xiliary valves
SD5 directional valve with left inlet
62 DAU003E
VU1 VU2
T A
100
B T
100
T A
100
B T
100
VU3
1450 145014501450
VU 1 ( G 3 -- 100 )
Adjustment type (G, H).
Spring type (2,3,4).
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
Standard setting in bar
(for value see page 53)
Anti--shock + anti--cavitation valve
Pressure drops
0
30
60
90
120
150
0 204060
Flow
Pressure
(l/min)
(bar)
V ant i--shock and anti--cavitation
Service and au xiliary valves
0
100
200
300
400
0 204060
Performance data
0
100
200
300
400
0204060
0
100
200
300
400
0 204060
Flow
Pressure
(l/min)
(bar)
Flow
Pressure
(l/min)
(bar)
Spring nr. 3 (blue band) Spring nr. 4 (red band)
Flow
Pressure
(l/min)
(bar)
Spring nr. 2 (green band)
0.1”
TIME REPONSE
10%
120 bar
90%
95%
105%
Pressure
Time (”)
(% P)
0.15”
TRANSITORY
19.5 bar / 280 psi
OPENING PEAK
Time response
G: with screw H: valve set and locked
Adjustment type
Allenwrench5
9.8 Nm / 7.2 lbft
Wrench 22
42 Nm / 31 lbft
Notch
1.5 mm / 0.06 in
(psi)
4500
3000
1500
(psi)
4500
3000
1500
(psi)
4500
3000
1500
1500
1000
500
(psi)
2000
1750 psi
directional valve with left inlet SD5
63DAU003E
Allenwrench8
24 Nm / 17.7 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
Wrench 24
42 Nm / 31 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
Pressure drop
0
30
60
90
120
0 204060
Flow
Pressure
(l/min)
(bar)
V ant i--shock and anti--cavitation
Service and au xiliary valves
VC1 VC2
T A B T T A B T
VC3
VT1 VT2
T A B T T A B T
VT3
VC 1
Anti--cavitation valve
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
VT 1
Valve blanking plug
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
1500
1000
500
(psi)
SD5 directional valve with left inlet
64 DAU003E
A1 A2
B1 B2
P
T
6220
59
23
2.32 0.91
0.79
2.44
17.5
35
D
24.5
11.5
77
13
22.3
T
P1
0.96 1.38
0.51
0.45
0.88
3.03
0.69
T
P1
1
2
3
Service and au xiliary valves
Block with pressure compensated 3 --way flow control valve, to be flange mounted on body with parallel circuit.
The cavity is oriented toward lever side.
The flow is regulated on every working section while the exceeding flow goes to tank: max. regulated flow 30 l/min (with inlet on P1
port).
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged (1) before the final honing of
spool hole, while the valve (3) is mounted during final assembling phase.
For information contact Sales Department.
VD1 flo w con t rol valves
Dimension D value (mm / in)
VD11 VD13VD12
171.5 / 6.75171.5 / 6.75121 / 4.76
directional valve with left inlet SD5
65DAU003E
Description example: SD5/2--P(JG3--120)VD12/18L/18L/AET
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 27
24 Nm / 17.7 lbft
P
A1 B1
120
P1
Hydraulic circuit
C
R
1750
Description example: SD5/2--P(JG3--120)VD11/18L/18L/AET
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 27
24 Nm / 17.7 lbft
VD1 flo w con t rol valves
Service and au xiliary valves
VD12: one turn with detent handknob regulated
Manual control
VD11: continuous fine regulation
SD5 directional valve with left inlet
66 DAU003E
0
10
20
30
40
30 90 150 210 270
0.3 0.6 0.9 1.2 Current (A)0
0
10
20
30
40
0.0 0.5 1.0 1.5 2.0 2.5
3 6 9 121518
Flow regulation diagram
Qin = 45 l/min -- P = 100 bar (1450 psi)
Priority flow
(l/min)
(n.of clicks)
(n.of turn)
0
F
J
Y
Performance data
Priority flow
(l/min)
Pressure (bar)
Pressure--flow diagram
Qin = 45 l/min
F
J
Y
VD1 1 flow control valve
VD12 flow control valve
VD13 flow control valve
(psi)
1000 2000 3000
Solenoid operating feautures
Nominal voltage : 12 VDC.........
Power rating : 28 W............
Duty cycle : 100%..............
To battery
Potentiometer for
valve adjustment
Emergency
push--button
Push--button panel type:
UPA12/100/SC01B22
ISO4400
connector
STOP
P
A1 B1
P1
C
R
120
1750
Hydraulic circuit
Proprtional solenoid flow control valve connection
It’s shows a configuration with push --button panel type UPA.
For information contact Sales Department.
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 27
24 Nm / 17.7 lbft
VD1 flo w con t rol valves
Service and au xiliary valves
VD13 with proportional solenoid control
Description example: SD5/2--P(JG3--120)VD13/18L/18L/AET
ISO4400 connection
(needs C02 connector ,
see page. 129)
directional valve with left inlet SD5
67DAU003E
SD5 directional valve with left inlet
68 DAU003E
Av ailable from 2 to 6 sections, it can be used in systems wich one downstream
section from series connection must work with upstream ones at the same time.
H On the same body are possible more than one connection.
H It’s not available the carry--over circuit.
H For controls, spool positioning and valves, refer to directional valve with paral-
lel circuit.
Other execu tio n s
It’s available only with one working section and it can be used in hydraulic cir-
cuits where c arry--over is required.
H For controls and spool positioning refer to directional valve with parallel circuit.
H Configurations with service and auxiliary valves aren’t available
It’s available only with one working section and it can be used in hydraulic cir-
cuits where c arry--over doesn’t required.
H For controls, spool positioning and valves, refer to directional valve with paral-
lel circuit.
SD5- SP: with tandem circuit page 74.........................
Av ailable from 2 to 6 sections, for security reasons it can be used in systems
which is required to prohibit engagement of downstream sections from tandem
connection when the upstream sections are working.
H On the same body are possible more than one connection.
H For controls, spool positioning and valves, refer to directional valve with paral-
lel circuit.
SD5- S: with series circuit page 72............................
SD5/1- D page 71...................................................
SD5/1- N page 70...................................................
directional valve with left inlet SD5
69DAU003E
0
5
10
15
0 15304560
Flow
Pressure
(l/min)
(bar)
PT
PA(B)
A(B)T
Pressure drop curve
(psi)
150
100
50
200
P
A1 B1
T
120
1750
Description example:
SD5/1--N(JG3--120)/18L
Code: 102110033
15
15
1
2
0
24
24
spool out
3
3
spool in
63.5 5
45
8.5
24.5
90
0.33
1.77
2.50 0.20
0.96
3.54
51
81
11.5
103
20
273024.5
46
45.5 34
186
14 73
105.5
M8
4.15
0.55
2.87
7.32
1.341.79
1.81
0.96
1.18 1.06
0.79
0.45
2.01
3.19
4.06
Dimensional data
Hydraulic circuit Performance data
SD5/1--N directional valve with left inlet
70 DAU003E
P
A1 B1
120
T
C
1750
Description example:
SD5/1--D(JG3--120)/18L
Code: 102160027
0
5
10
15
20
0 15304560
Flow
Presure
(l/min)
(bar)
PC
PA(B)
A(B)T
Pressure drop curve
(psi)
150
100
50
200
51
81
11.5
103
20
273023.5
46
45.5 34
186
13 73
102
M8
4.02
2.87
0.51
7.32
1.341.79
1.81
0.93 1.18
1.06
0.45
0.79
4.06
3.19
2.01
Dimensional data
Hydraulic circuit Performance data
15
15
1
2
0
24
24
spool out
3
3
spool in
63.5 5
45
8.5
24.5
90
0.33
1.77
2.50
0.20
0.96
3.54
directional valve with left inlet SD5/1--D
71DAU003E
30 37
51
81
34
186
103
45
12.5
11.5
23
45.5
27
M8
20
F
E
0.49
7.32
1.34
1.79
1.77
0.91
1.18
1.46
1.06
0.79
0.45
2.01
3.19
4.06
Dimensional data
15
15
1
2
0
24
24
spool out
3
3
spool in
63.5 5
45
24.5
90
8.5
0.33
0.96
1.77
2.50
0.20
3.54
SD5--S directional valve with left inlet
72 DAU003E
T
Y
P
E
E F Weight
T
Y
P
E
E F Weight
T
Y
P
E
mm in mm in kg lb
T
Y
P
E
mm in mm in kg lb
SD5/2--S
137.5 5.41 110 4.33 5.2 11.4
SD5/5--S
248.5 9.78 221 8.70 10.1 22.3
SD5/3--S
174.5 6.87 147 5.79 6.9 15.2
SD5/6--S
285.5 11.2 258 10.2 11.7 25.8
SD5/4--S
211.5 8.33 184 7.24 8.1 17.9
0
10
20
30
40
0 15304560
Flow
Pressure
(l/min)
(bar)
Pressure drop
between port A(B) before series
connection and port A(B) after
(psi)
450
300
150
0
10
20
30
40
0 15304560
A
6
(B
6
)T
A
1
(B
1
)T
Flow
Pressure
(l/min)
(bar)
Pressure drop A(B)T
on 6 sections directional valve
(psi)
450
300
150
0
10
20
30
40
0 15304560
PA
6
(B
6
)
Flow
Pressure
(l/min)
(bar)
Pressure drop PA(B)
on 6 sections directional valve
PA
1
(B
1
)
(psi)
450
300
150
0
10
20
30
40
0 15304560
Flow
Pressure
(l/min)
(bar)
Pressure drop PT
2 sections
4 sectionis
6 sections
(psi)
450
300
150
The description of SD5 valve with series circuit is marked with letter “S” and one figure wich indicate the downstream sections from
series connection.
Hydraulic circuit
Performance data
A3 B3 A4 B4
T
Description example: SD5/4--S1(JG3--120)/18L/18L/18L/18L
Code: 1024B0027
*
P
A1 B1 A2 B2
120
NOTE (*) -- Codes are referred to BSP thread.
1750
Available body kits *
CODE DESCRIPTION
5KC1 153040 SD5/2--S1
5KC1253003 SD5/3--S1
5KC12D3000 SD5/3--S1+1
5KC1283003 SD5/4--S1
5KC12E3000 SD5/4--S1+1+1
5KC1324033 SD5/5--S1
5KC1073001 SD5/5--S1+1+1+1
5KC13A3000 SD5/5--S2+1
5KC1363003 SD5/6--S1
Include boby, seals and load check
valves.
directional valve with left inlet SD5--S
73DAU003E
51
81
34
186
103
45
12,5
11.5
45.5
M8
20
F
E
0.49
1.34
1.79
1.77
7.32
30 3723 27
0.91
1.18
1.46
1.06
0.45
2.01
3.19
4.06
0.79
Dimensional data
15
15
1
2
0
24
24
spool out
3
3
spool in
20.5
Carry--over
0.81
63.5
5
45
8.5
24.5
90
3.54
2.50
1.77
0.20
0.96
0.33
SD5--SP directional valve with left inlet
74 DAU003E
T
Y
P
E
E F Weight
T
Y
P
E
E F Weight
T
Y
P
E
mm in mm in kg lb
T
Y
P
E
mm in mm in kg lb
SD5/2--SP1
137.5 5.41 110 4.33 4.8 10.6
SD5/5--SP4
248.5 9.78 221 8.70 10.2 22.5
SD5/3--SP2
174.5 6.87 147 5.79 6.7 14.8
SD5/6--SP5
285.5 11.2 258 10.2 11.3 24.9
SD5/4--SP3
211.5 8.33 184 7.24 8.1 17.6
SD5/7--SP6
322.5 13.1 295 11.6 12.7 28
0
10
20
30
40
0 15304560
0
10
20
30
40
0 15304560
A
6
(B
6
)T
A
1
(B
1
)T
Flow
Pressure
(l/min)
(bar)
PA
6
(B
6
)
Flow
Pressure
(l/min)
(bar)
0
10
20
30
40
0 15304560
Flow
Pressure
(l/min)
(bar)
Pressure drop PT Pressure drop PA(B)
on 6 sections directional valve
Pressure drop A(B)T
on 6 sections directional valve
PA
1
(B
1
)
6 sections
4 sections
(psi)
450
300
150
2 sections
(psi)
450
300
150
(psi)
450
300
150
The description of SD5 valve with tandem circuit is marked with letters “SP” and one figure wich indicate the downstream sections
from tandem connection.
Hydraulic circuit
Performance data
A3 B3 A4 B4
Description example: SD5/4--SP3(JG3--120)/18L/18L/18L/18L/AET
Code: 1024A0016
*
P
A1 B1 A2 B2
120
T
NOTE (*) -- Codes are referred to BSP threads.
Available body kits *
CODE DESCRIPTION
5KC1 183000 SD5/2--SP1
5KC12G3000 SD5/3--SP2
5KC1303000 SD5/4--SP1
5KC12H3000 SD5/4--SP1+1
5KC12I3000 SD5/4--SP2+1
5KC1293000 SD5/4--SP3
5KC13D3000 SD5/5--SP2+2
5KC1343000 SD5/5--SP3+1
5KC1333000 SD5/5--SP4
5KC1393000 SD5/6--SP3+1
5KC13Y3000 SD5/6--SP3+2
5KC1373000 SD5/6--SP5
5KC13I3000 SD5/7--SP3+1
5KC13G3000 SD5/7--SP4
5KC13L3000 SD5/7--SP5+1
5KC13F3000 SD5/7--SP6
Include boby, seals and load check
valve.
directional valve with left inlet SD5--SP
75DAU003E
SD5
76 DAU003E
SD5
77DAU003E
Contents
Directional valve with parallel circuit
Dimensional data 78..................................
Hydraulic circuit 79...................................
Ordering codes 80....................................
Inlet relief options 12..................................
Spools 82...........................................
“A” side spool positioners 86..........................
“B” side options 39...................................
Complete controls 44.................................
Outlet port options 97.................................
Service and auxiliary valves
ordering codes 100................................
port relief valves 102...............................
flange mounted relief valves 103....................
fixed setting antishock and anticavitation valves 104....
adjustable setting antishock and anticavitation valves106
flow control valves 110.............................
Other execu tio n s
Main features 113....................................
Directional valve SD5/1--N 114.........................
Directional valve SD5/1--D 115.........................
Directional valve SD5 --S with series circuit 116...........
Directional valve SD5--SP with tandem circuit 118.........
Directional valve SDM105 eith flow control 120...........
Dimensional data (parallel circuit)
3037
51
81
34
198.5 max.
103
12.5
11.5
23
45.5
27
20
F
E
11.5
44
10.5
M8
90
24.5
45
63.5
5
8.5
15
15
1
2
0
24
24
spool out
3
3
spool in
WALVOIL
SD5/2--P
P0200001
102219002
MADE IN ITALY
20.5
Carry--over
0.81
0.45
4.06
3.19
2.01
0.79
0.49
1.73
0.41
0.45
1.34
1.79
1.06 1.46 1.18 0.91
7.81 max.
0.33
1.77
2.5
0.20
0.96
3.54
WALVOIL
SD5/2--P
P0500001
102200039
MADE IN ITALY
Code
Production batch:
P05 = production year (2005)
00001 = progressive number
Type
SD5 directional valve with right inlet
78 DAU003E
T
Y
P
E
E F Weight
T
Y
P
E
E F Weight
T
Y
P
E
mm in mm in kg lb
T
Y
P
E
mm in mm in kg lb
SD5/1--P
100.5 3.96 73 2.87 3.5 7.7
SD5/5--P
248.5 9.78 221 8.70 10.1 22.3
SD5/2--P
137.5 5.41 110 4.33 5.2 11.5
SD5/6--P
285.5 11.24 258 10.16 11.7 25.8
SD5/3--P
174.5 6.87 147 5.79 6.9 15.2
SD5/7--P
322.5 12.70 295 11.61 13.2 29.1
SD5/4--P
211.5 8.33 184 7.24 8.1 17.9
Hydraulic circuit
Lever pivot box
Check valve
Allenwrench4
24 Nm / 17.7 lbft
Configuration with upper inlet and outlet
P
B1 A1B2 A2
T
Description example:
SD5/2--P(JG3--120)/ED--18L/ED--18L/AET-- PSA
120
P
B1 A1B2 A2
T
Description example:
SD5/2--P(JG3--120)/ED--18L/ED--18L/AET
120
Standard configuration
Tank line
Flow through
(LC)
Pressure line
Port A line
Port B line
Positioner kit
Plug for open centre
Allenwrench8
24 Nm / 17.7 lbft
Main relief valve
A
B
P
T
Parallel
Standard configuration with side inlet and outlet and open centre (AET execution).
1750
1750
directional valve with right inlet SD5
79DAU003E
SD5 directional valve with right inlet
80 DAU003E
2. Inlet relief options page 12
1. Body kit *
Ordering codes3.
2.
SD5 / 2 -- P (JG3--120) / ED -- 1 8 L / ED -- 18ES3 . P3(G3--100) / AET *
TYPE CODE DESCRIPTION
1--P 5KC1 193000 Parallel, 1 section
2--P 5KC1223000 Parallel, 2 sections
3--P 5KC1243000 Parallel, 3 sections
4--P 5KC1273000 Parallel, 4 sections
5--P 5KC1313000 Parallel, 5 sections
6--P 5KC1353000 Parallel, 6 sections
7--P 5KC13E3000 Parallel, 7 sections
TYPE CODE DESCRIPTION
VMD5 direct pressure relief valve type J
Standard setting is referred to 10 l/min flow .
(JG2--63) 5KIT105412 Range 40 to 63 bar / 580 to 900 psi
standard setting 63 bar / 900 psi
(JG3--120) 5KIT105413 Range 50 to 200 bar / 725 to 2900 psi
standard setting 120 bar / 1750 psi
(JG4--220) 5KIT105414 Range 160 to 315 bar / 2300 to 4600 psi
standard setting 220 bar / 3200 psi
SV XTAP623282 Relief valve blanking plug
4. 5.
Include boby, seals and load check valve.
1
st
section following section
Description examp le:
1.
3.
3. Spool options page 82
TIPO CODICE DESCRIZIONE
ED--1 3CU1210730 Double acting, 3 positions, with A and B
closed in neutral position
ED--1B 3CU1222700 Double acting, 3 positions, with B open to
tank in neutral position
ED--2 3CU1225730 Double acting, 3 positions, with A and B
open to tank in neutral position
ED--2H 3CU1225790 Double acting, 3 positions, with A e B
partially open to tank in neutral position
ED--4 3CU1235700 Single acting on B, 3 positions, A plugged
requires G3/8 plug (see part I )
Special spools for particular positioner kits
ED--5PY 3CU1245700 Double acting, 4 positions, floating circuit
in 4
th
position with spool out, with check
valve
Special spools for standard positioner kits
ED--8F 3CU1261700 Double acting, 3 positions, regenerative
circuit in 2
nd
position with spool out
NOTE (*) -- Codes are referred to BSP threads.
7.6. 8.
Valve setting (bar)
Valve setting (bar)
6.
4.
8.
9.
I
2.
1.
3.
6.
7.
directional valve with right inlet SD5
81DAU003E
II Optional handlevers
TYPE CODE DESCRIPTION
AL01/M8x120 170011012 For lever L: height 120 mm / 4.72 in
AL01/M10x150 170012015 For lever LM10:
height 150 mm / 5.91 in
AL08/M12x150 170013115 For joystick LCB:
height 150 mm / 5.91 in
7. Aux. and service valves page 100
8. Outlet port options page 97
TYPE CODE DESCRIPTION
AET XT AP623170 Open centre plug
AEK 3XTAP522282 Closed centre plug
AE 3XGIU522460
* G3/8 carry--over sleeve
AET--L XCAR405300 With hydraulic pilot unloader valve
AET--LT XT AP523370 Unloader valve blanking plug
Electric control unloader valve: for valves and coils list see page 98.
9. Inlet an d o u t let selection * page 79
4. “A” side spool positioners page 86
Ordering codes
TYPE CODE DESCRIPTION
8 5V08104000 With spring return in neutral position
8D 5V08104200 With spring return in neutral position and
pin with M6 female thread for dual control
8D2 5V08104220 With spring return in neutral position and
pin with M8 male thread for dual control
8F2 5V08104101 With spring return in neutral position and
adjustable flow limiter
19 5V19104000 2 positions, with spring return in neutral
position from position 1
20 5V19104000 2 positions, with spring return in neutral
position from position 2
9 5V09104010 With detent in position 1 and spring return
in neutral position
10 5V10104011 With detent in position 2 and spring return
in neutral position
11 5V11104000 Detent in positions neutral, 1 and 2
12 5V12104000 Detent in positions 1 and 2
15 5V15104000 2 positions, detent in positions 1 and
neutral
16 5V16104000 2 positions, detent in positions 2 and
neutral
9BZ 5V09204010 With detent in position 1 and spring return
in neutral position
10BZ 5V10204010 With detent in position 2 and spring return
in neutral position
11B Z 5V1 1204010 Detent in positions 1 and 2 and spring
return in neutral position
8MG3 5V08104660 With spring return in neutral position and
microswitch in positions 1 and 2
8P 5V08104701 ON/OFF pneumatic kit
8EP3 5V08104735 ON/OFF 12 VDC electro--pneumatic kit
5V08104740 ON/OFF 24 VDC electro--pneumatic kit
8ED3 5V08104350 ON/OFF 12 VDC electro--hydraulic kit
5V08104351 ON/OFF 24 VDC electro--hydraulic kit
Particular positioner kits for special spools
13QN 5V13404020 4 pos. with spring return in neutral pos.
and detent in 4
th
pos.: for spool 5PY
TYPE CODE DESCRIPTION
PSL 3XTAP722160 Side ports; need n.2 G 3/8 plugs, standard
configuration (omit in valve description)
PSA 3XT AP722160 Upper ports; need n.2 G 3/8 plugs
Port relief, anti--shock, pilot operated check and flow regulation valves.
6. Complete controls page 44
Proportional hydraulic control type 8IM and ON/OFF solenoid control
type 8ES.
5. “B” side options page 39
TYPE CODE DESCRIPTION
L 5LEV105000 Standard lever box
LM10 5LEV205000 Lever box for M10 handlever
LF1 5LEV105102 Lever box with adjustable flow limiter
LEB 5LEV605000 Safety lever box, vertical configuration
LUP 5LEV805005 Safety lever box, horizontal configuration
SLP 5COP105000 Witout lever box, with dust--proof plate
SLC 5COP205000 Witout lever box, with endcap
TQ 5TEL105110 Flexible cable connection
LCB 5CLO205100 Joystick lever for 2 sections operation
I ”A” and “B” ports plugs *
TYPE CODE DESCRIPTION
G3/8 3XTAP722160 for single acting spool type 3
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke (mm)
(l/min )
Spool metering A(B)T
5.5
(in)
0.1 0.2
Flow
Stroke
Spool metering PA(B)
(mm)
(l/min )
5.5
(in)
0.1 0.2
F
J
Y
P
(on ports)
= 63bar / 900 psi
P
(on ports)
= 100bar / 1450 psi
P
(on ports)
= 250bar / 3600 psi
Qin = 45 l/min
20
29
0.35
0.79
A
"
Tipo ED--1
Spool options
201
201
201
AB
PT
Performance data
AB
PT
AB
PT
For special requirement, spool 1CEX code 3CU1210780 suggested for flow up to 15 l/min
P--A--B--T closed, with flow through line (LC) open
145.5
13.5
BA
TPLC T
PABT
BA
TPLC T
PBAT
BA
TPLC T
5.73
0.53
stroke:
+5.5mm/0.22 in
stroke:
-- 5 . 5 m m / 0.22 in
F
J
Y
F
J
Y
SD5 directional valve with right inlet
82 DAU003E
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
201
AB
PT
Type ED -- 2H
Type ED -- 2
Type ED -- 1B
Spool options
Type ED -- 4
201
AB
PT
P--A closed, BT, flow through line (LC) open
P closed, A--B partially open to tank,
flow through line (LC) open
BA
TPLC T
201
AB
PT
P closed, A--BT, flow through line (LC) open
BA
TPLC T
BA
TPLC T
B
TPLC T
P--A--T closed, flow through line (LC) open
201
B
PT
Port A closed
Allenwrench6
24 Nm / 17.7 lbft
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
directional valve with right inlet SD5
83DAU003E
stroke:
+9mm/0.35in
BA
TPLC T
BA
TPLC T
BA
TPLC T
0132
AB
PT
0
5
10
15
20
0 15304560
Pressure
Flow (l/min)
(bar)
Pressure drop in position 3
(last section)
A(B)T
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke (mm)
(l/min )
5.5
PAAT
It needs special body with extra machining: for information please contact Sales Department.
This spool must be coupled with positioner type 13QN (see page 96).
Spool options
Tipo ED--5PY
Performance data
A-- BT (floating detent)
PB,AT
A
""
"
stroke:
+4.5mm/0.18 in
corsa+9mm
PA,BT
P--A--B--T closed,
with flow through line (LC) open
BA
TPLC T
0132
AB
PT
013 2
AB
PT
013 2
AB
PT
PB
AT
BT
stroke:
+4.5mm/0.18 in
Spool metering
Qin=45l/min/P
(on ports)
= 100 bar -- 1450 psi
(in)
0.1 0.2
(psi)
200
100
SD5 directional valve with right inlet
84 DAU003E
201
AB
PT
Type ED -- 8F
Spool options
0
20
40
60
0.0 1.0 2.0 3.0 4.0 5.0
Flow
Stroke (mm)
(l/min )
201
201
AB
PT
Performance data
AB
PT
5.5
P--A--B--T closed flow through line (LC) open
P B,A T
It needs special body with extra machining: for information please contact Sales Department.
P A--B (regenerative)
0
5
10
15
20
0 15304560
Pressure
Flow (l/min)
(bar)
Pressure drop in position 1
(in first section)
PA
BA
PBAT
BA
TPLC T
BA
TPLC T
BA
TPLC T
"
stroke:
+5.5mm/0.22 in
A
stroke:
-- 5 . 5 m m / 0.22 in
Spool metering
Qin=45l/min/P
(on ports)
= 100 bar -- 1450 psi
0.1 0.2
(psi)
200
100
(in)
directional valve with right inlet SD5
85DAU003E
10
40
18
20
4
M6
15
8
8
Spool end joint dimensions
0.16
0.39 0.79
0.31
0.71
1.57
0.31
0.59
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
D
D
E
C
C
E
0.1 0.2
(in)
40
20
(lbf)
-- 0 . 1-- 0 . 2 0
60
0
-- 4 0
-- 2 0
-- 6 0
With spring return in neutral position
”A” side spool positioners
8kit
8D kit
8D2 kit
201
201
201
It’s supplied with standard spring type D (see force--stroke diagram) and available with lighter spring type C (8MC code:5V08204000)
or heavier type E (8ME code: 5V08404000).
Spool end joint code XPER315400, is available on request in order to screw onto pin.
40
M6
40
47.5
M8
40
87.5
40
Allenwrench4
6.6 Nm / 4.9 lbft
Allenrench5
9.8 Nm / 7.2 lbft
1.57
1.57
1.87
12
0.47
Wrench 9
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 9
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.57
1.57
3.44
SD5 directional valve with right inlet
86 DAU003E
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0
Stroke
Force
(mm)
(N)
Force --stroke diagram
(in)
40
20
60
0
-- 4 0
-- 2 0
-- 6 0
(lbf)
-- 0 . 1-- 0 . 2
--300
--200
--100
0
100
200
300
0123456
Stroke
Force
(mm)
(N)
Force --stroke diagram
(in)
40
20
60
0
-- 4 0
-- 2 0
-- 6 0
(lbf)
0.1 0.2
201
With spring return in neutral position
”A” side spool positioners
8F2 kit
19 kit
55
M8x1
40
40
20 kit
01
40
20
2.17
1.57
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
Wrench 13
24 Nm / 17.7 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
1.57
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.57
directional valve with right inlet SD5
87DAU003E
Operating features
Locking and release force : 100 N / 22.5 lbf 10%........
Operating features
Locking and release force : 100 N / 22.5 lbf 10%........
Operating features
Locking and release force : 100 N / 22.5 lbf 10%........
Operating features
Locking and release force : 120 N / 27 lbf 10%........
Operating features
Locking force (from pos. 0 to 2) : 150 N / 33.7 lbf 10%...
Release (from pos. 2 to 0) : 140 N / 31.5 lbf 10%.......
Operating features
Locking force (from pos. 0 to 1) : 150 N / 33.7 lbf 10%...
Release force (from pos. 1 to 0) : 140 N / 31.5 lbf 10%...
40
201201
201
With detent
”A” side spool positioners
9kit
11 kit
15 kit
49
44.5
40
10 kit
201
12 kit
01
40
20
40
16 kit
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.93
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
1.75
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.57
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
1.57
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.57
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1.57
SD5 directional valve with right inlet
88 DAU003E
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
Locking force: 120 N / 27 lbf 10% / Release force: 230 N / 51.7 lbf 10%
201
Port B Port A
-- 3 . 3
-- 5 . 5
5.5
3.3
Detent area
40
20
(lbf)
60
0
-- 4 0
-- 2 0
-- 6 0
0.1 0.2
(in)
-- 0 . 1-- 0 . 2 0
-0.19
-0.22
0.22
0.13
Detent area
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
Locking force: 120 N / 27 lbf 10% / Release force: 230 N / 51.7 lbf 10%
Detent area
201
Port B Port A
-- 3 . 3
-- 5 . 5
5.5
40
20
(lbf)
60
0
-- 4 0
-- 2 0
-- 6 0
0.1 0.2
(in)
-- 0 . 1-- 0 . 2 0
-0.13
-0.22
0.22
--300
--200
--100
0
100
200
300
-- 6 -- 5 -- 4 -- 3 -- 2 -- 1 0 1 2 3 4 5 6
Stroke
Force
(mm)
(N)
Force --stroke diagram
Locking force: 120 N / 27 lbf 10% / Release force: 230 N / 51.7 lbf 10%
Detent area
201
Port B Port A
3.3
0.22
-- 5 . 5
40
20
(lbf)
60
0
-- 4 0
-- 2 0
-- 6 0
0.1 0.2
(in)
-- 0 . 1-- 0 . 2 0
-0.22
40
20
60
0
-- 4 0
-- 2 0
-- 6 0
5.5
0.13
With detent and sprimg return to neutral position from either directions
”A” side spool positioners
9BZ kit
10BZ kit
11BZ kit
201
201
201
76
76
76
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
2.99
2.99
2.99
directional valve with right inlet SD5
89DAU003E
SD5 directional valve with right inlet
90 DAU003E
COMPLETE CONTROLS CODE
CONTROL TYPE
Need
Contact 8MG3 8MG2 8MG1
N
e
e
d
connector type
NO
5V08104660 5V08104680 5V08104670 C07
see page
129
PACKARD W--PACK
male connector with
female end
PACKARD W--PACK
female connector
with male end
With NO contact
code: 4MIC730
With NC contact
code: 4MIC740
84,5 128
3.33 5.04
It’s possible to obtain further configurations of complete control, using the MG kit, microswitches and 3 positions “A” side spool posi-
tioner, as following draw.
More configurations and spare parts
201
8MG1(NO) kit
201
201
Other configurations
8MG2(NO) kit
8MG3(NO) kit
Operating features
MICROSWITCH
Mechanical life : 5x10
5
operations...........
Electrical life (resistive load) : 10
5
oper. -- 7A / 13.5VDC
:5x10
4
oper -- 10A / 12VDC
:5x10
4
per -- 3A / 28VDC
With microswitch type 8MG3(NO)
”A” side spool positioners
With spring return in neutral position and microswitch operated in both directions.
Also available 8MG1 (NO) configuration (microswitch operated in position 1) and 8MG2(NO) configuration (microswitch operated in
position 2); dimensions are the same of 8MG3 configuration.
Same configurations are available on request with normally closed (NC) contact.
70
Microswitch with connector
Kit MG--ED
Microswitch
Kit MG3
code: 5KIT820400
Kit MG1
code: 5KIT820401
Kit MG2
code: 5KIT820402
3 positions “A” side spool
positioner type 9B, 10B, 11B for
left inlet directional valve.
(see page 23)
Wrench 22
42 Nm / 31 lbft
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench4--6.6Nm/4.9 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 10
9.8 Nm / 7.2 lbft
Operating features
ACTUATOR
Lock stroke : 3.5 mm / 0.14 in.....................
COIL
Depending on model: see following features
Solenoid lock device
“A” side spool positioners
3 positions “A” side spool
positioner type 8, 9B, 10B, 11B for
left inlet directional valve.
(see pages 20 and 23)
Fitted with actuator:
code: 5KIT810400
Coils
Kit K--ED
Coil with ISO4400 connector
Nom. voltage tolerance : 10%.
Power rating : 18 W..........
Nominal current : 1.58 A -- 12 VDC........
: 0.81 A -- 24VDC
Coil insulance : Class F.........
Weather protection : IP65.....
Duty cycle : 100%............
Coil with Deutsch DT connector
Nom. voltage tolerance : 10%.
Power rating : 22 W..........
Nominal current : 1.9 A -- 12 VDC........
: 0.95 A -- 24VDC
Coil insulance : Class H.........
Weather protection : IP65.....
Duty cycle : 100%............
Coil with Packard M--Pack connector
Nom. voltage tolerance : 10%.
Power rating : 18 W..........
Nominal current : 1.58 A -- 12 VDC........
: 0.81 A -- 24VDC
Coil insulance : Class F.........
Weather protection : IP65.....
Duty cycle : 100%............
634
It’s possible to obtain further configurations of complete control, using the kit K--ED (for right inlet directional valve), coils and 3 posi-
tions “A” side spool positioner for left inlet directional valve, as following draw: for information contact Sales Department.
25
directional valve with right inlet SD5
91DAU003E
COILS CODE
CONNECTION TYPE
Voltage ISO4400 Deutsch DT Packard M--Pack
12 VDC 2X4300012 2X4300014 YSOL300013
24 VDC 2X4300024 2X4300026 YSOL300025
Need
connector type
(see page 129)
C02 C19 C20
SD5 directional valve with right inlet
92 DAU003E
COMPLETE CONTROL CODES
CONNECTION TYPE
ISO6952 Flying leads
CONTROL TYPE
Voltage 8EP3 8EP35
12 VDC 5V08104735 5V08104736
24 VDC 5V08104740 5V08104741
Need
connector type
(see page 129)
C01
(included)
/
COIL CODES
V
o
l
t
a
g
e
CONNECTION TYPE
V
o
l
tage
ISO6952 Flying leads*
12 VDC 2X4000013 2XB1000120000
24 VDC 2X4000025 2XB1000240000
* Several type of connectors can be wired on request
Wrench 14 -- 9.8 Nm / 7.2 lbft
42
113.5
43
1.69
4.47
1.65
Coil with ISO6952
connector
Coil with flying leads
200
7.87
Operating features
CONTROL
Pilot pressure : 6 bar / 87 psi..............
: (max.10 bar / 145 psi)
COIL
Nominal voltage tolerance : 10%....
Power rating : 8 W...............
Nominal current : 0,67 A -- 12 VDC.............
: 0,33 A -- 24VDC
Coil insulation : Class F..............
Weather protection : IP65..........
Duty cycle : 100%.................
ON/OFF electropneumatic kit type 8EP3
“A” side spool positioners
122.5
60.5
V1 V2
Pg9
Scheme ISO 1219
Scheme
201
V1 V2
201
V1 V2
6
Ø
0.24
2.38
122.5
4.82
Special wrench -- 9.8 Nm / 7.2 lbft
Allenwrench4--6.6Nm/4.9 lbft
Wrench 9
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench13--24Nm/17.7 lbft
Operating features
Pilot pressure : min. 5.5 bar / 80 psi............
: max. 10 bar / 145 psi
Collector
119.5
136.5
Coil
62.5
42
133
142.5
ON/OFF electrohydraulic kit type 8ED3
“A” side spool positioners
With external pilot and drain.
Operating features
CONTROL
Pilotpressure :min.10bar/145 psi..............
: max. 50 bar / 725 psi
Max backpressure on drain L : 25 bar
/ 360 psi.
COIL
Nominal voltage tolerance : 10%....
Power rating : 21 W...............
Nominal current : 1.75 A -- 12 VDC.............
0.87 A -- 24VDC
Coil insulation : Class F..............
Weather protection : IP65..........
Duty cycle : 100%.................
121.5
55
23
V1
V2
NPT 1/8” -- nr.2 thread
Wrench 10 -- 9.8 Nm / 7.2 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 11 -- 9.8 Nm / 7.2 lbft
ON/OFF pneu matic kit type 8P
With spring return to neutral position.
201
V1 V2
Allenwrench4--6.6Nm/4.9 lbft
2.16
4.78
0.91
Scheme ISO 1219
Scheme
201
201
VL
L
V
1
Solenoid valve:
wrench 24 -- 9.8 Nm / 7.2 lbft
6.6 Nm -- 4.9 lbft
Allenwrench4--6.6Nm/4.9 lbft
Special wrench -- 9.8 Nm / 7.2 lbft
Wrench10--24Nm/17.7 lbft
Wrench 10
Allenwrench4--6,6Nm/4.9 lbft
5.37
4.70
1.65 2.46
5.61
directional valve with right inlet SD5
93DAU003E
COMPLETE CONTROL CODES
CONNECTION TYPE
I
S
O
4
4
0
0
AMP JPT
D
e
u
t
s
c
h
D
T
I
S
O
44
0
0
without diodo with diodo
D
eutsc
h
D
T
CONTROL TYPE
Voltage 8ED3 8ED32 8ED32D 8ED34
12 VDC 5V080104350 5V08104250 5V08104280 5V08104450
24 VDC 5V08104351 5V08104251 5V08104281 5V08104451
Need
connector type
(see page 129))
C02 C08 C08 C19
Collector kit for external pilot and drain
Coil with
ISO4400 connection
Coil with
AMP JPT connection
Coil with Deutsch DT connection
ON/OFF electrohydraulic kit type 8ED3
“A” side spool positioners
V
20 bar
290 psi
L
Collector
P
T
154
Description example:
SD5/2--P(JG3--120)/ED--18ED3L/ED --18ED3L/AET--
KE2S0--24VDC
P
B1 A1B2 A2
T
120
V
L
170
6.69
1750
6.06
SD5 directional valve with right inlet
94 DAU003E
COIL CODES
CONNECTION TYPE
I
S
O
4
4
0
0
AMP JPT
D
e
u
t
s
c
h
D
T
Voltage
I
S
O
44
0
0
without diodo with diodo
D
eutsc
h
D
T
12 VDC 2XB1400121 100 2XB1400121200 2XB1400121210 2XB1400120400
24 VDC 2XB1400241 100 2XB1400241200 2XB1400241210 2XB1400240400
COLLECTOR KIT CODES
Type Code * Description
KE1S0 5KE1S00030 Kit one section
KE2S0 5KE2S00230 Kit for 2 sections
KE3S0 5KE3S00230 Kit for 3 sections
KE4S0 5KE4S00230 Kit for 4 sections
KE5S0 5KE5S00230 Kit for 5 sections
KE6S0 5KE6S00230 Kit for 6 sections
(*) codes are referred to BSP thread
Pressure drop PT
0
10
20
30
40
0153045
Flow
Pressure
(l/min)
(bar)
400
200
(psi)
“A” side spool positioners
Collector kit with pilot and drain lines
The kit is made of collector, VRP pressure reducing valve and pipes.
ON/OFF electrohydraulic kit type 8ED3
VRC valve: code X003600010
Valve assembled on flow through passage provides pilot pressure to the actuator.
35
154
136 28
Collector
Inlet line
Drain line
T
P
Wrench 19 -- 24 Nm / 17.7 lbft
Wrench 22
24 Nm / 17.7 lbft
Wrench 17
VRP Code:
2S100808V AL21
Allenwrench6
24 Nm / 17.7 lbft
VRC backpressure
valve (not included)
Description example:
SD5/2--P(JG3--120)/ED--18ED3L/ED --18ED3L/
VRC--KE2R3--24VDC
P
B1 A1B2 A2
T
120
L
VRP
VRC
Wrench 22
42 Nm / 31 lbft
20
Wrench 22
24 Nm / 17.7 lbft
5.35 1.10
1.38
6.06
Operating features
VRP VALVE
Output pressure : 20 bar / 290 psi............
Max flow : 8 l/min..................
Filtering : 80 ...................
1750
0.79
directional valve with right inlet SD5
95DAU003E
COLLECTOR KIT CODES
Tipo Code * Description
KE1R0 5KE1R30230 Kit one section
KE2R0 5KE2R30230 Kit for 2 sections
KE3R0 5KE3R30230 Kit for 3 sections
KE4R0 5KE4R30230 Kit for 4 sections
KE5R0 5KE5R30230 Kit for 5 sections
KE6R0 5KE6R30230 Kit for 6 sections
(*) Codes are referred to BSP thread
Detent area
Locking force: 360 N / 81 lbf 10%
Release force: 390 N / 87.7 lbf 10%
--400
--200
0
200
400
--5--4--3--2--10123456789
Stroke
Forza
(mm)
(N)
Force --stroke diagram
201
Port B Port A
3
-- 4 . 5
4.5
Floating
6.8
60
30
(lbf)
0
-- 6 0
-- 3 0
(in)
0.1 0.20 0.3-- 0 . 1
-0.18
0.18
0.27
Particular positioner kits for special spools
“A” side spool positioners
13QN kit
Detent in 4
th
position with spool out:available only for spool type ED--5PY (see page 84).
2013
76
Special body kit
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 6
9.8 Nm / 17.7 lbft
2.99
SD5 directional valve with right inlet
96 DAU003E
0
3
6
9
12
0 10203040
Pressure drop curve
Flow
Pressure
(l/min)
(bar)
45
(psi)
150
100
50
Operating features
Internal leakage : 10 cm
3
/min a 100 bar.................
: 0.61 in
3
/min at 1450 psi
AE:with carry--over
AET: open centre (standard)
Outlet port options
See page 79.
Description example:
SD5/2--P(KG3--120)/ED--18L/ED--18L/AE
Description example:
SD5/2--P(KG3--120)/ED--18L/ED--18L/AEK
20.5
G3/8
Wrench 22
42 Nm / 31 lbft
C
2.5
Allenwrench8
42 Nm / 31 lbft
With hydraulic pilot unloader valve type L
For safety reasons it’s provided with pilot port plugged.
10
G1/4
X
B2 A2
T
Description example:
SD5/2--P(JG3 --120)/ED --18L/ED--18L/AET --L
X
AEK: closed cen t re
It’s possible to have open centre, closed centre and carry--over.
Unloader valves are available: these valves need special bodies with appropriate cavity on lateral outlet port, the tank connection
T must be on top.
P
B1 A1B2 A2
T
120
C
P
B1 A1B2 A2
T
120
0.81 0.098
Wrench24--42Nm/31 lbft
0.39
1750
1750
directional valve with right inlet SD5
97DAU003E
Description example:
SD5/2--P(JG3--120)/ED--18L/ED--18L/AET --ELNW--12VDC
With solenoid pilot unloader valve
Outlet port options
For the complete valve must be ordered the cartridge and the coil both; to follow please see code list and description composi-
tion.
1. Solenoid pilot unloader valve
TYPE CODE DESCRIPTION
AET--ELNW 0EFW0132002 Normally open, without emergency
AET--ELNW(NC) 0EFW0132003 As previous, normally closed
AET--ELTW 0EFW0132000 Normally open, with “push&twist”
emergency type
AET--ELPW 0EFW0132001 Normally open, with push--button
emergency type
2. Coil
TYPE CODE DESCRIPTION
With ISO4400 connection
12VDC 4SLE001200 Nominal voltage 12VDC
DB--12VDC 4SLE001217 As previous, with bi--directional diode
24VDC 4SLE002400 Nominal voltage 24VDC
DB--24VDC 4SLE002408 As previous, with bi--directional diode
With AMP JPT connection
2--12VDC 4SLE001203 Nominal voltage 12VDC
2DB--12VDC 4SLE001211 As previous, with bi--directional diode
2--24VDC 4SLE002403 Nominal voltage 24VDC
With Deutsch DT conenction
4--12VDC 4SLE001202 Nominal voltage 12VDC, parallel
connection
4DB--12VDC 4SLE001216 As previous, with bi--directional diode
4PD--12VDC 4SLE001201 Nominal voltage 12VDC,
perpendicular connection
4PDDB--12VDC 4SLE001209 As previous, with bi--directional diode
4--24VDC 4SLE002402 Nominal voltage 24VDC, parallel
connection
4PD--24VDC 4SLE002401 Nominal voltage 24VDC,
perpendicular connection
4PDDB--24VDC 4SLE002407 As previous, with bi--directional diode
Description examp le:
Example of directional valve with
normally open unloader valve
Example of directional valve with
normally closed unloader valve
B2 A2
T
Description example:
SD5/2--P(JG3--120)/ED--18L/ED--18L/AET--ELNW(NC) --12VDC
B2 A2
T
SD5 / 2 -- P (JG3--120) / ED--18L / ED--18L / AET--ELNW 4 (NC) -- 12VDC
1. 2.2. 1.
SD5 directional valve with right inlet
98 DAU003E
parallel type
ISO4400
connection
AMP JPT
connection
perpendicular type
Deutsch DT connection
Valve operating features
Max. flow : 45 l/min................
Max. pressure : 315 bar / 4600 psi............
Internal leakage (from 1 to 2) : max. 3 cm
3
/min at 100 bar
: max . 4.6 in
3
/min at 1450 psi
Coil operating features
Nominal voltage tolerance. : 10%
Power rating : 19.3 W -- 12 VDC...........
: 19.2 W -- 24 VDC
Max. operating curent : 1.61 A -- 12 VDC....
: 0.80 A -- 24VDC
Coil insulation : Class H..........
Weather protection : IP65 -- ISO4400......
: IP69K -- Deutsch DT
:IP65--AMPJPT
Insertion : 100%...............
0
5
10
15
20
25
0 5 10 15 20 25 30 35 40 45
Valve pressure drop
from 1 to 2 in open position
Flow
Pressure
(l/min)
(bar)
EL(NC)
EL(NA)
(psi)
300
200
100
With solenoid pilot unloader valve
Outlet port options
LT: unloader valve prearrangement
2
1
2
1
Type ELN
Type ELN(NC)
2
1
Type ELP
63 92.5
2
1
Type ELT
90.5
67
A2 B2
T
Description example>
SD5/2--P(JG3--120)/ED--18L/ED--18L/AET--LT
2.64
2.48 3.56 3.64
Wrench 24
42 Nm / 31 lbft
Allenwrench6
24 Nm / 17.7 lbft
directional valve with right inlet SD5
99DAU003E
SD5 directional valve with right inlet
100 DAU003E
Mounting on the opposite
side of working ports
5.
3.
1.
2.
Srvice and au xiliary valves10.
4.
VS
Kit VM
All service and auxiliary valves need special body: contact Sales Department.
VM(...)
VMT
VM(...)
VMT
Kit V
VP
VU
VC
VT
VP
VU
VC
VT
Relef valve
Relef valve
Anti- shock + anti- cavitation valve
Anti- shock + anti- cavitation valve
(fixed setting)
VSC(JG...)
VSCT
Kit VS
VD23
VD22
VD21
Kit VD1
Flow control valves
directional valve with right inlet SD5
101DAU003E
NOTE -- Valve setting at points 1--2--4--5--6 are referred to 10 l/min flow.
NOTE -- ( *) Codes are referred to BSP threads.
3. VM anti--schock+anti--cavitation valve page 104
Flange mounted type with fixed setting and fitted with mounting block.
TYPE CODE DESCRIPTION
VM(50) 5KIT326050 Setting 50 bar / 725 psi
VM(60) 5KIT326060 Setting 60 bar / 870 psi
VM(70) 5KIT326070 Setting 70 bar / 1010 psi
VM(80) 5KIT326080 Setting 80 bar / 1 150 psi
VM(90) 5KIT326090 Setting 90 bar / 1300 psi
VM(100) 5KIT326100 Setting 100 bar / 1450 psi
VM(125) 5KIT326125 Setting 125 bar / 1800 psi
VM(140) 5KIT326140 Setting 140 bar / 2050 psi
VM(160) 5KIT326160 Setting 160 bar / 2300 psi
VM(175) 5KIT326175 Setting 175 bar / 2550 psi
VM(190) 5KIT326190 Setting 190 bar / 2750 psi
VM(210) 5KIT326210 Setting 210 bar / 3050 psi
VM(230) 5KIT326230 Setting 230 bar / 3350 psi
VM(250) 5KIT326250 Setting 250 bar / 3600 psi
VM(260) 5KIT326260 Setting 260 bar / 3750 psi
VM(280) 5KIT326280 Setting 280 bar / 4050 psi
VM(300) 5KIT326300 Setting 300 bar / 4350 psi
VMT XTAP221340 Valve blanking plug
Kit VM 5CO2820020 Mounting block kit
Service and au xiliary valves
1. Relief valves page 102
TYPE CODE DESCRIPTION
VS(G3--100) 3XCAR505113 Range 40 to 200 bar / 580 to 2900 psi
standard setting 100 bar / 1450 psi
VST 3XTAP419300 Valve blanking plug
5. Flow control valves page 110
Flow control on every section; with auxiliary inlet
TYPE CODE DESCRIPTION
VD21 2S0PP10002000 Fine regulation from 3 to 28 l/min
VD22 2S163602021 1 As VD11, one turn with detent
VD23 2S0PP10002002 12VDC proportional solenoid valve
Kit VD2 5CO2822020
* Mounting block kit
2. Flange mounted relief valve page 103
TYPE CODE DESCRIPTION
VSC(JG2--60) 5KIT105412 Range 40 to 80 bar / 580 to 1150 psi
standard setting 60 bar / 870 psi
VSC(JG3--100) 5KIT105413 Range 63 to 200 bar / 900 to 2900 psi
standard setting 100 bar / 1450 psi
VSC(JG4--200) 5KIT105414 Range 160 to 250 bar / 2300 to 3600 psi
standard setting 200 bar / 2900 psi
VSCT XTAP623282 V alve blanking plug
Kit VS 5CO2420000 Mounting block kit
Set of valves fitted with mounting block.
TYPE CODE DESCRIPTION
Kit V 5CO2820010 Mounting block kit
T XTAP524280 Valve blanking plug
C 5KIT4061 10 Anti--cavitation valve
Anti--shock valves
P(G2) 5KIT206112 Range 60 to 125 bar / 870 to 1800 psi
standard setting 80 bar / 1150 psi
P(G3) 5KIT206113 Range 80 to 200 bar / 1150 to 2900 psi
standard setting 120 bar / 1750 psi
P(G4) 5KIT206114 Range 160 to 250 bar / 2300 to 3600 psi
standard setting 200 bar / 2900 psi
Anti--shock + anti--cavitation valves
U(G2) 5KIT3051 12 Range 40 to 100 bar / 580 to 1450 psi
standard setting 80 bar / 1150 psi
U(G3) 5KIT3051 13 Range 80 to 200 bar / 1150 to 2900 psi
standard setting 120 bar / 1750 psi
U(G4) 5KIT3051 14 Range 160 to 315 bar / 2300 to 4600 psi
standard setting 200 bar / 2900 psi
4. V anti--schock+anti--cavitation valve page 106
0,08”
TIME RESPONSE
10%
100 bar
90%
95%
105%
Pressure
Time (”)
(% P)
Time response
1450 psi
Spring nr. 3 (blue band)
0
100
200
300
400
0 102030
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
Adjustment type (G, H)
VS ( G 3 -- 100 )
Pressure setting in bar (standard 100 bar / 1450 psi)
VS relief valve
Service and au xiliary valves
It’s suggested for flow up to 25 l/min, and it’s mounted on parallel body to limitate the pressure, at lower value than main relief valve
(min. gap 20 bar / 290 psi ), on downstream section.
It’s in parallel with flow trough and it works only with single operation.
14
18.5 18.5
B2 B1
T
P
C
C
Hydraulic circuit
Description example:
SD5/2--P(KG3--120)/ED--18L/VS(G3--100)/ED--18L/AET --PSA
Spring type
P
B1 A1B2 A2
T
120
100
C--C
24.5
max.
G: with screw
H: valve set and locked
C--C
Adjustment type
Wrench 10
9.8 Nm / 7.2 lbft
Wrench 17
24 Nm / 17.7 lbft
Wrench 19
24 Nm / 17.7 lbft
Allenwrench3
0.96
4
0.16
VST: valve blanking plu g
Allenwrench6
42 Nm / 31 lbft
1750
1450
Performance data
0.73
0.73
0.55
SD5 directional valve with right inlet
102 DAU003E
1
2 3
It’s flange mounted on parallel body on the opposite side of working ports, the function to limit the pressure, at lower value than main
relief v alve (min. gap 20 bar / 290 psi) on downstream sections.
It’s in parallel with flow through line and it works only with single operation.
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged (1) before the final honing of
spool hole, while the valve (3) is mounted during final assembling phase.
For information contact Sales Department.
VSC relief valve
Service and au xiliary valves
P
B1 A1B2 A2
T
Description example:
SD5/2--P(JG3--120)/ED --18L/VSC(JG3--100)/ED--18L/AET
120
100
VSC ( J G 3 -- 100 )
Adjustment type (G, H).
Adjustable spring type (2, 3, 4).
Standard setting in bar
(for value see page 101)
NOTE -- For performance
data, wrench and
tightening force, please
see page 12.
13
32
max. 106
24.5
Wrench 4
6.6 Nm / 4.9 lbft
34 54.5
21.5
43 37.5
53
37
A2 A1
B2 B1
T
P
T
1750
1450
1.46
2.09
1.48
1.69
0.85
max. 4.17
2.151.34
1.26
0.96
0.51
directional valve with right inlet SD5
103DAU003E
1
2
3
VM an ti--shock and anti--cavitatio n
Service and au xiliary valves
They are flange mounted on the opposite side of working ports, connected in parallel with A and B ports and with outlet on T port.
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged on body (1) before the final
honing of spool hole, while the valve (3) is mounted during final assembling phase.
For information contact Sales Department.
ValveonportB
ValveonportA
27.5
40.5
14
86
13.5
24.5
5.5
A2 A1
B2 B1
T
P
15.3
36.6 21.9
53
37
T
1.46
2.09
0.60
1.44 0.86
0.22
3.39
0.55
1.08
1.59 0.96
0.53
SD5 directional valve with right inlet
104 DAU003E
VM1 VM2 VM3
AB
T
ABAB
TT
100
1450
100
1450
100
1450
100
1450
0
50
100
150
200
250
300
350
0 10203040
Pressure--flow diagram
Flow
Pressure
(bar)
(l/min)
45
(psi)
4500
3000
1500
VM an ti--shock and anti--cavitatio n
Service and au xiliary valves
Example of VM1 configuration
Allenwrench10
24 Nm / 17.7 lbft
Allenwrench6
24 Nm / 17.7 lbft
T
Allenwrench4
6.6 Nm / 4.9 lbft
Valve setting in bar
1 mounted on port A
2 mounted on port B
3 mounted on ports A and B
VM 1 (100)
directional valve with right inlet SD5
105DAU003E
1
2
They are anti--shock (VP), anti--shock and anti--cavitation (VU) and anti --cavitation (VC) service valves, flange mounted on the
opposite side of working ports connected in parallel with A and B ports.
They need a dedicated body with extra machining: for production requirements, the blocks (2) are flanged on body (1) before the
final honing of spool hole, while the valves (3) are mounted during final assembling phase.
For information contact Sales Department
V ant i--shock and anti--cavitation
Service and au xiliary valves
3
2
3
ValveonportBValveonportA
57.5
32.5
2
2535
16
D
T
18
36 22.5
5337
1
A2 A1
B2 B1
T
P
5.5 / 0.22
Dimension D value (mm / in)
VP VCVU VT
9.5 / 0.37
14 / 0.55
max.
14 / 0.55
max.
1.46 2.09
0.89
1.42
0.71
0.039
2.26
1.28
0.079
1.38
25
0.98
0.63
SD5 directional valve with right inlet
106 DAU003E
VP1 VP2
T A
100
B T
100
T A
100
B T
100
VP3
1450
1450 1450
1450
VP 1 ( G 3 -- 100 )
Adjustment type (G, H).
Spring type (2,3,4).
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
Standard setting in bar
(for value see page 101)
Anti--shock valve
V an ti--schock+anti--cavitation valves
Service and au xiliary valves
G: with screw H: valve set and locked
Adjustment type
T
Allenwrench5
9.8 Nm / 7.2 lbft
Notch
1.5 mm / 0.06 in
T
Wrench 22
42 Nm / 31 lbft
0,02”
TIME RESPONSE
10%
100 bar
90%
95%
105%
Pressure
Time (”)
(% P)
Time response
1450 psi
0
100
200
300
400
0 204060
Spring nr.4 (red band)
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
0
100
200
300
400
0204060
Spring nr. 3 (blue band)
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
0
100
200
300
400
0 204060
Spring nr. 2 (green band)
Flow
Pressure
(l/min)
(bar)
(psi)
4500
3000
1500
Performance data
directional valve with right inlet SD5
107DAU003E
VU1 VU2
T A
100
B T
100
T A
100
B T
100
VU3
1450 145014501450
VU 1 ( G 3 -- 100 )
Adjustment type (G, H).
Spring type (2,3,4).
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
Standard setting in bar
(for value see page 53)
Anti--shock + anti--cavitation valve
V ant i--shock and anti--cavitation
Service and au xiliary valves
G: with screw H: valve set and locked
Adjustment type
T T
Allenwrench5
9.8 Nm / 7.2 lbft
Notch
1.5 mm / 0.06 in
Wrench 22
42 Nm / 31 lbft
Pressure drops
0
30
60
90
120
150
0 204060
Flow
Pressure
(l/min)
(bar)
0
100
200
300
400
0 204060
Performance data
0
100
200
300
400
0204060
0
100
200
300
400
0 204060
Flow
Pressure
(l/min)
(bar)
Flow
Pressure
(l/min)
(bar)
Spring nr. 3 (blue band) Spring nr. 4 (red band)
Flow
Pressure
(l/min)
(bar)
Spring nr. 2 (green band)
0.1”
TIME REPONSE
10%
120 bar
90%
95%
105%
Pressure
Time (”)
(% P)
0.15”
TRANSITORY
19.5 bar / 280 psi
OPENING PEAK
Time response
(psi)
4500
3000
1500
(psi)
4500
3000
1500
(psi)
4500
3000
1500
1500
1000
500
(psi)
2000
1750 psi
SD5 directional valve with right inlet
108 DAU003E
VC 1
Anti--cavitation valve
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
Perdita di carico
0
30
60
90
120
0 204060
Portata
Pressione
(l/min)
(bar)
V ant i--shock and anti--cavitation
Service and au xiliary valves
VC1 VC2
TA BT TABT
VC3
VT1 VT2
TA BT TABT
VT3
Allenwrench5
9.8 Nm / 7.2 lbft
Wrench 24
42 Nm / 31 lbft
VT 1
Valve blanking plug
1 mounted on port A.
2 rmounted on port B.
3 mounted on ports A and B.
Allenwrench5
9.8 Nm / 7.2 lbft
Allenwrench8
24 Nm / 17.7 lbft
directional valve with right inlet SD5
109DAU003E
1
VD2 flo w con t rol valves
Service and au xiliary valves
Block with pressure compensated 3 --way flow control valve, to be flange mounted on body with parallel circuit.
The cavity is oriented toward lever side.
The flow is regulated on every working section while the exceeding flow goes to tank: max. regulated flow 28 l/min (with inlet on P1
port).
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged (1) before the final honing of
spool hole, while the valve (3) is mounted during final assembling phase.
For information contact Sales Department.
45 18
40.5
17.5
35
D
24.5
80
G3/8
13.5
T
A2 A1
B2 B1
T
P
13.4
P1
T
T
P1
2
3
Dimension D value (mm / in)
VD21 VD23VD22
174.5 / 6.87174.5 / 6.87124 / 4.88
1.59
1.77
0.71
3.15
0.53
0.53
0.69
1.38 0.96
SD5 directional valve with right inlet
110 DAU003E
VD2 flo w con t rol valves
Service and au xiliary valves
Manual control
Description example: SD5/2--P(JG3--120)VD11/ED--18L/ED --18L/AET
Description example: SD5/2--P(JG3--120)VD12/ED --18L/ED--18L/AET
P
B1 A1
120
P1
VD21: continuous fine regulation
VD22: one turn with detent handknob regulated
Hydraulic circuit
C
R
P1
T
P1
T
Allenwrench4
6.6 Nm / 4.9 lbft
Wrench 27
24 Nm / 17.7 lbft
Wrench 27
24 Nm / 17.7 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1750
directional valve with right inlet SD5
111DAU003E
Solenoid operating feautures
Nominal voltage : 12 VDC.........
Power rating : 28 W............
Duty cycle : 100%..............
VD2 flo w con t rol valves
Service and au xiliary valves
VD13 with proportional solenoid control
P
B1 A1
120
P1
Description example: SD5/2--P(JG3--120)VD13/ED --18L/ED--18L/AET
Proprtional solenoid flow control valve connection
STOP
To battery
ISO4400
connec tor
Potentiometer for
valve adjustment
Emergency
push--button
Push--button panel type:
UPA12/100/SC01B22
It’s shows a configuration with push --button panel type UPA.
For information contact Sales Department.
C
R
Hydraulic circuit
ISO4400 connection
(needs C02 connector,
see page. 129)
P1
T
Wrench 27
24 Nm / 17.7 lbft
Allenwrench4
6.6 Nm / 4.9 lbft
1750
0
10
20
30
40
30 90 150 210 270
0.3 0.6 0.9 1.2 Current (A)0
0
10
20
30
40
0.0 0.5 1.0 1.5 2.0 2.5
3 6 9 121518
Flow regulation diagram
Qin = 45 l/min -- P = 100 bar (1450 psi)
Priority flow
(l/min)
(n.of clicks)
(n.of turn)
0
F
J
Y
Performance data
Priority flow
(l/min)
Pressure (bar)
Pressure--flow diagram
Qin = 45 l/min
F
J
Y
VD1 1 flow control valve
VD12 flow control valve
VD13 flow control valve
(psi)
1000 2000 3000
SD5 directional valve with right inlet
112 DAU003E
Av ailable from 2 to 6 sections, it can be used in systems wich one downstream
section from series connection must work with upstream ones at the same time.
H On the same body are possible more than one connection.
H It’s not available the carry--over circuit.
H For controls, spool positioning and valves, refer to directional valve with paral-
lel circuit.
Other execu tio n s
It’s available only with one working section and it can be used in hydraulic cir-
cuits where c arry--over is required.
H For controls and spool positioning refer to directional valve with parallel circuit.
H Configurations with service and auxiliary valves aren’t available
It’s available only with one working section and it can be used in hydraulic cir-
cuits where c arry--over doesn’t required.
H For controls, spool positioning and valves, refer to directional valve with paral-
lel circuit.
SD5- SP: with tandem circuit page 118........................
Av ailable from 2 to 6 sections, for security reasons it can be used in systems
which is required to prohibit engagement of downstream sections from tandem
connection when the upstream sections are working.
H On the same body are possible more than one connection.
H For controls, spool positioning and valves, refer to directional valve with paral-
lel circuit.
SD5- S: with series circuit page 116...........................
SD5/1- D page 115..................................................
SD5/1- N page 114..................................................
SDM105: with flow control valve page 120...................
One section available.
H It can be configured with unloader valve.
H For controls and spool positioning refer to directional valve with parallel circuit.
H Configurations with service and auxiliary valves aren’t available.
directional valve with right inlet SD5
113DAU003E
0
5
10
15
0 15304560
Flow
Pressure
(l/min)
(bar)
PT
PA(B)
A(B)T
Pressure drop curve
(psi)
150
100
50
200
Performance data
P
B1 A1
T
120
1750
Dimensional data
Hydraulic circuit
Description example
SD5/1--N(JG3--120)/ED--18L
Code: 102110033
51
81
11.5
103
20
27 30
24.5
46
45.534
193.5
14
73
105.5
M8
63.5 5
45
8.5
24.5
90
15
15
1
2
0
24
24
spool out
3
3
spool in
1.06
1.18
0.96
1.81
45.5
1.791.35
7.62
4.15
2.87
0.55
0.79
4.06
3.19
2.01 0.45
0.33
2.50
1.77
0.20
0.96
3.54
SD5/1--N directional valve with right inlet
114 DAU003E
0
5
10
15
20
0 15304560
Flow
Presure
(l/min)
(bar)
PC
PA(B)
A(B)T
Pressure drop curve
(psi)
150
100
50
200
Performance data
Dimensional data
51
81
11.5
103
20
27 30 23.5
46
45.5
34
193.5
13
73
102
P
A1 B1
Description example:
SD5/1--D(JG3--120)/ED --18L
Code: 102160027
120
T
C
63.5 5
45
8.5
24.5
90
15
15
1
2
0
24
24
spool out
3
3
spool in
M8
Hydraulic circuit
1750
1.06 1.18 0.93
1.81
1.79
1.34
7.62
0.45
2.01
3.19
0.79
4.06
4.02
2.87
0.51
0.96
3.54
2.50
1.77
0.20
0.33
directional valve with right inlet SD5/1--D
115DAU003E
Dimensional data
3037
51
81
34
193.5
103
45
12.5
11,5
23
45.5
27
20
F
E
63.5 5
45
8.5
24.5
90
15
15
1
2
0
24
24
spool out
3
3
spool in
M8
1.06 1.46 1.18
0.91
1.77
1.79
1.34
7.62
0.49
0.79
4.06
3.54
0.96
0.33
1.77
2.5
0.20
SD5--S directional valve with right inlet
116 DAU003E
T
Y
P
E
E F Weight
T
Y
P
E
E F Weight
T
Y
P
E
mm in mm in kg lb
T
Y
P
E
mm in mm in kg lb
SD5/2--S
137.5 5.41 110 4.33 5.2 11.4
SD5/5--S
248.5 9.78 221 8.70 10.1 22.3
SD5/3--S
174.5 6.87 147 5.79 6.9 15.2
SD5/6--S
285.5 11.2 258 10.2 11.7 25.8
SD5/4--S
211.5 8.33 184 7.24 8.1 17.9
NOTE (*) -- Codes are referred to BSP thread.
Available body kits *
CODE DESCRIPTION
5KC1 153040 SD5/2--S1
5KC1253003 SD5/3--S1
5KC12D3000 SD5/3--S1+1
5KC1283003 SD5/4--S1
5KC12E3000 SD5/4--S1+1+1
5KC1324033 SD5/5--S1
5KC1073001 SD5/5--S1+1+1+1
5KC13A3000 SD5/5--S2+1
5KC1363003 SD5/6--S1
Include boby, seals and load check
valves.
Hydraulic circuit
The description of SD5 valve with series circuit is marked with letter “S” and one figure wich indicate the downstream sections from
series connection.
B3 A3B4 A4
T
Description example:
SD5/4--S1(JG3 --120)/ED --18L/ED--18L/ED--18L/ED--18L
P
B1 A1B2 A2
120
0
10
20
30
40
0 15304560
Flow
Pressure
(l/min)
(bar)
Pressure drop
between port A(B) before series
connection and port A(B) after
(psi)
450
300
150
0
10
20
30
40
0 15304560
A
6
(B
6
)T
A
1
(B
1
)T
Flow
Pressure
(l/min)
(bar)
Pressure drop A(B)T
on 6 sections directional valve
(psi)
450
300
150
0
10
20
30
40
0 15304560
PA
6
(B
6
)
Flow
Pressure
(l/min)
(bar)
Pressure drop PA(B)
on 6 sections directional valve
PA
1
(B
1
)
(psi)
450
300
150
0
10
20
30
40
0 15304560
Flow
Pressure
(l/min)
(bar)
Pressure drop PT
2 sections
4 sectionis
6 sections
(psi)
450
300
150
Performance data
directional valve with right inlet SD5--S
117DAU003E
Dimensional data
30
37
51
81
34
193.5
103
45
12.5
11.5
23
45.5
27
20
F
E
20,5
Carry--over
90
24.5
45.5
63.5
5
8.5
15
15
1
2
0
24
24
spool out
3
3
spool in
M8
1.06 1.46 1.18
0.91
1.79 1.771.34
7.62
0.49
0.79
0.45
2.01
3.19
4.06
3.54
0.96
0.33
2.50
1.79
0.20
SD5--SP directional valve with right inlet
118 DAU003E
T
Y
P
E
E F Weight
T
Y
P
E
E F Weight
T
Y
P
E
mm in mm in kg lb
T
Y
P
E
mm in mm in kg lb
SD5/2--SP1
137.5 5.41 110 4.33 4.8 10.6
SD5/5--SP4
248.5 9.78 221 8.70 10.2 22.5
SD5/3--SP2
174.5 6.87 147 5.79 6.7 14.8
SD5/6--SP5
285.5 11.2 258 10.2 11.3 24.9
SD5/4--SP3
211.5 8.33 184 7.24 8.1 17.6
SD5/7--SP6
322.5 13.1 295 11.6 12.7 28
Hydraulic circuit
The description of SD5 valve with tandem circuit is marked with letters “SP” and one figure wich indicate the downstream sections
from tandem connection.
B3 A3B4 A4
Description example:
SD5/4--SP3(JG3 --120)/ED --18L/ED--18L/ED--18L/ED--18L/AET
P
B1 A1B2 A2
120
Available body kits *
CODICE DESCRIZIONE
5KC1 183000 SD5/2--SP1
5KC12G3000 SD5/3--SP2
5KC1303000 SD5/4--SP1
5KC12H3000 SD5/4--SP1+1
5KC12I3000 SD5/4--SP2+1
5KC1293000 SD5/4--SP3
5KC13D3000 SD5/5--SP2+2
5KC1343000 SD5/5--SP3+1
5KC1333000 SD5/5--SP4
5KC1393000 SD5/6--SP3+1
5KC13Y3000 SD5/6--SP3+2
5KC1373000 SD5/6--SP5
5KC13I3000 SD5/7--SP3+1
5KC13G3000 SD5/7--SP4
5KC13L3000 SD5/7--SP5+1
5KC13F3000 SD5/7--SP6
Include boby, seals and load check
valve.
T
NOTE (*) -- Codes are referred to BSP threads.
0
10
20
30
40
0 15304560
0
10
20
30
40
0 15304560
A
6
(B
6
)T
A
1
(B
1
)T
Flow
Pressure
(l/min)
(bar)
PA
6
(B
6
)
Flow
Pressure
(l/min)
(bar)
0
10
20
30
40
0 15304560
Flow
Pressure
(l/min)
(bar)
Pressure drop PT Pressure drop PA(B)
on 6 sections directional valve
Pressure drop A(B)T
on 6 sections directional valve
PA
1
(B
1
)
6 sections
4 sections
(psi)
450
300
150
2 sections
(psi)
450
300
150
(psi)
450
300
150
Performance data
1750
directional valve with right inlet SD5--SP
119DAU003E
Dimensional data
15 110
137.5
47.5 37 30 23
30
34.5
10.5 81
103
13
34
20
44
11.5
193.5
12.5
45
63.5 5
24.5
96
M10
15
15
1
2
0
24
24
spool out
3
3
spool in
8.5
1.87
1.46 1.18 0.91
1.34
0.51
7.62
0.49
5.41
4.33
0.59
0.41
0.79
1.18 1.36
3.19
0.45
4.061.73
2.50
1.77
0.33
0.96
3.78
0.20
SDM105 directional valve with right inlet
120 DAU003E
P
B1 A1
120
T
0
5
10
15
20
0 15304560
0
5
10
15
20
0 15304560
Flow
Pressure
(l/min)
(bar)
Flow
Pressure
(l/min)
(bar)
0
5
10
15
20
0 15304560
Flow
Pressure
(l/min)
(bar)
Pressure drop PT Pressure drop PA(B)
Pressure drop A(B)T
(psi)
(psi)
240
160
80
Hydraulic circuit
Description example:
SDM105/1(JG3 --120)M/110L/LT
Performance data
Positioner kit
Main relief valve
Flow control with
wheel regulation
Compensator
spool
Lever pivot box
Flow through
(LC)
Pressure line
Tank line
P
T
Port A line
Port B line
240
160
80
(psi)
240
160
80
Compensator front plug
Allen wrench 8 -- 24 Nm / 17.7 lbft
Compensator rear plug
Allenwrench10--24Nm/17.7 lbft
1750
directional valve with right inlet SDM105
121DAU003E
SDM105 directional valve with right inlet
122 DAU003E
2. Inlet relief options page 121. Body kit *
Ordering codes
2.
2.
SDM105 / 1 -- P (JG3--120) M / 2 10 L / EL--12VDC -- ........
TYPE CODE DESCRIPTION
1--P 5KC5013000 Parallel, 1 section
TYPE CODE DESCRIPTION
VMD5 direct pressure relief valve type J
Standard setting is referred to 10 l/min flow .
(JG2--63) 5KIT105412 Range 40 to 63 bar / 580 to 900 psi
standard setting 63 bar / 900 psi
(JG3--120) 5KIT105413 Range 50 to 200 bar / 725 to 2900 psi
standard setting 120 bar / 1750 psi
(JG4--220) 5KIT105414 Range 160 to 315 bar / 2300 to 4600 psi
standard setting 220 bar / 3200 psi
SV XTAP623282 Relief valve blanking plug
3. 7.
Include boby and seals.
1.
Description examp le:
I
7.
3.
10.
6.
1.
5.
NOTE (*) -- Codes are referred to BSP threads.
9.
9.
5.
Valve setting in bar
6. 10.
SDM105 / 1 -- P (JG3--120) M / 18ES3 / LT -- 12VDC
8.
4.
directional valve with right inlet SDM105
123DAU003E
9. Solenoid pilot unloaer valve page
NO TAG
I Optional handlevers
Ordering codes
TYPE CODE DESCRIPTION
AL01/M10x150 170012015 For lever L:
height 150 mm / 5.91 in
8. Complete controls page 46
ON/OFF solenoid control type 8ES.
7. “B” side options page 39
TYPE CODE DESCRIPTION
L 5LEV205000 Lever box for M10 handlever
(for dimensions see LM10 for SD5
directional valve)
SLP 5COP105000 Witout lever box, with dust--proof plate
TQ 5TEL105110 Flexible cable connection
TYPE CODE DESCRIPTION
EL--12VDC YCAR405305 With 12VDC electric control unloader
valve; normally open circuit
EL--24VDC YCAR405310 As previous 24VDC
ELC--12VDC 5CAR405330 With 12VDC electric control unloader
valve; normally closed circuit
ELC--24VDC 5CAR405331 As previous 24VDC
LT XTAP523370 V alve blanking plug
5. Spool options page 125
TYPE CODE DESCRIPTION
1 3CU1210730 Double acting, 3 positions, with A and B
closed in neutral position
2 3CU1225730 Double acting, 3 positions, with A and B
open to tank in neutral position
Special spools for particular positioner kits
5T 3CU1243701 Double acting, 4 positions, floating circuit
in 4
th
position with spool out.
3. Flow controls page 124
TYPE CODE DESCRIPTION
M XCAR70521 1 Continuous fine wheel regulation
G XCAR705202 Screw regulation with locking nut
10. Inlet and out let selection * page 79
TYPE CODE DESCRIPTION
PSL 3XTAP722160 Side ports; need n.2 G 3/8 plugs, standard
configuration (omit in valve description)
PSA 3XT AP722160 Upper ports; need n.2 G 3/8 plugs
6. “A” side spool positioners page 86
TYPE CODE DESCRIPTION
8 5V08104000 With spring return in neutral position
8D 5V08104200 With spring return in neutral position and
pin with M6 female thread for dual control
8D2 5V08104220 With spring return in neutral position and
pin with M8 male thread for dual control
8F2 5V08104101 With spring return in neutral position and
adjustable flow limiter
19 5V19104000 2 positions, with spring return in neutral
position from position 1
20 5V19104000 2 positions, with spring return in neutral
position from position 2
9 5V09104010 With detent in position 1 and spring return
in neutral position
10 5V10104011 With detent in position 2 and spring return
in neutral position
11 5V11104000 Detent in positions neutral, 1 and 2
12 5V12104000 Detent in positions 1 and 2
15 5V15104000 2 positions, detent in positions 1 and
neutral
16 5V16104000 2 positions, detent in positions 2 and
neutral
9BZ 5V09204010 With detent in position 1 and spring return
in neutral position
10BZ 5V10204010 With detent in position 2 and spring return
in neutral position
11B Z 5V1 1204010 Detent in positions 1 and 2 and spring
return in neutral position
8MG3 5V08104660 With spring return in neutral position and
microswitch in positions 1 and 2
8P 5V08104701 ON/OFF pneumatic kit
8EP3 5V08104735 ON/OFF 12 VDC electro--pneumatic kit
5V08104740 ON/OFF 24 VDC electro--pneumatic kit
8ED3 5V08104350 ON/OFF 12 VDC electro--hydraulic kit
5V08104351 ON/OFF 24 VDC electro--hydraulic kit
Particular positioner kits for special spools
13QN 5V13404020 4 pos. with spring return in neutral pos.
and detent in 4
th
pos.: for spool 5T
4. Compensato r kit
TYPE CODE DESCRIPTION
-- 5CAS316065 Compensator kit
0
15
30
45
60
012345
0
15
30
45
60
30 90 150 210 270
Type M
Flow controls
Continuous fine wheel regulation
Type G
Continuous screw regulation with locking nut.
35.5 min.
40.5 max.
26.5
Wrench 22
24 Nm / 17.7 lbft
27 min.
32 max.
Wrench 22
24 Nm / 17.7 lbft
Wrench 13
24 Nm / 17.7 lbft
Allenwrench4
Flow regulation diagram
Qin = 45 l/min -- P = 100 bar (1450 psi)
Priority flow
(l/min)
Priority flow
(l/min)
Pressure (bar)
Pressure--flow diagram
Qin = 45 l/min
Pressure compensated flow control with max. regulated flow = 45 l/min.
1.04
1.40 min.
1.59 max.
1.26 max.
1.06 min.
(psi)
1000 2000 3000
nr. of turns
SDM105 directional valve with right inlet
124 DAU003E
0132
AB
PT
Type 5T
Type 2
Type 1
Spool options
P--A--B--T closed, with flow through line (LC) open
P--A--B--T closed, with flow through line (LC) open
BA
TPLC T
201
AB
PT
P closed, A--BT, flow through line (LC) open
BA
TPLC T
201
AB
PT
BA
TPLC T
A
""
"
+4.5mm/0.18 in
+9mm/0.35 in
(0)
(1)
(2)
(3)
It needs special body with extra machining: for information please contact Sales Department.
This spool must be coupled with positioner type 13QN (see page 96).
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
A
-- 5 , 5 m m / 0.22 in
"
+5,5mm/0.22 in
(0)
(1)
(2)
-- 4 . 5 m m / 0.18 in
directional valve with right inlet SDM105
125DAU003E
SD5
126 DAU003E
Fittings tightening torque -- Nm / lbft
THREADS TYPE P and C ports A a nd B ports T port
BSP (ISO 228/1) G3/8 G3/8
G3/8(G 1/2*)
With O--Ring seal 35 / 25.8 35 / 25.8
35 / 25.8(50 / 36.9*)
With copper washer 40 / 29.5 40 / 29.5
40 / 29.5 (50 / 36.9*)
With steel and rubber washer 30 / 22.1 30 / 22.1
30 / 22.1 (50 / 36.9*)
UN--UNF (ISO 11926 --1) 3/4--1 6 UNF --2B (SAE 8) 9/16--18 UNF --2B (SAE 6) 3/4--16 UNF--2B (SAE 8)
With O--Ring seal 40 / 29.5 30 / 22.1 30 / 22.1
METRIC (ISO 262) M18 x 1 .5 M18 x 1.5
M18 x 1.5 (M22x1.5*)
With O--Ring seal 35 / 25.8 35 / 25.8
35 / 25.8 (50*)
With copper washer 40 / 29.5 40 / 29.5
40 / 29.5 (50*)
With steel and rubber washer 40 / 29.5 40 / 29.5
40 / 29.5 (50*)
(
*
)
O
n
l
y
f
o
r
s
e
r
i
e
s
c
i
r
c
u
i
t
(
*
)--On
l
y
fo
r
s
e
r
i
e
s
c
i
r
cu
i
t.
Installation and maintenan ce
A2
P
T
C
A1
B1
B2
SD5 directional valve
The SD5 valve is assembled and tested as per the technical specification of this catalogue.
Before the final installation on your equipment, follow the below recommendations:
-- the valve can be assembled in any position, in order to prevent body deformation and spool sticking mount the product on a flat
surface;
-- in order to prevent the possibility of water entering the lever box and spool control kit, do not use high pressure wash down directly
on the valve;
-- prior to painting, ensure plastic port plugs are tightly in place.
NOTE -- These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating and
surface finish. The manufacturer shall be consulted.
A1
B1
P
T
with carry --over configuration
SDM105 directional valve
Installation and maintenan ce
NOTE -- All articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI2
Body
Positioner kit
O--Ring seal 15.88x2.62 -- code: 4GUA115926
Note
In case of assistance follw this assembling procedure
-- fit the O--Rimg seal in seat on lever side;
-- fit the spool from the opposite side and till it is possible to
fit the other O--Ring seal;
-- position the spool in centre.
Sealing edge
Spool
Load check valve
Normally spools are interchange-
able. Verify the smoothness dur-
ing the assembly
Main relief valve
Lever
pivot box
SD5 directional cont rol valve
SD5
127DAU003E
Malfunction Cause Remedy
External leakage pivot box lever or
control kit side.
Worn spool seal due to mechanical
actuation or high back pressure.
Locate the leakage and replace the seal.
Check back pressure level.
Excessive internal leakage on A and B
ports.
Increase clearance between spools and
body due to high wear.
Replace the directional control valve and
check the oil contamination level.
Dropping load during transition while
raising
High leakage on the load check valve.
Remove the load check valve and clean
the s eat, verifing it’s not dented.
Inability to build pressure on A and B
Pressure relief valve blocked open. Remove and clean or replace the valve.
I
n
a
b
i
l
i
t
y
t
o
b
u
i
l
d
p
r
e
s
s
u
r
e
o
n
A
a
n
d
B
ports.
Low pump pressure and flow.
Check the pump and circuit.
Installation and maintenan ce
NOTE -- All articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI2
SDM105 directional control valve
Lever pivot box
Positioner kit
Main relief valve
Flow control with wheel regulation
Compensator spool
Spool
Normally spools are interchange-
able. Verify the smoothness dur-
ing the assembly
Body
O--Ring seal 15.88x2.62 -- code: 4GUA115926
Note
In case of assistance follw this assembling procedure
-- fit the O--Rimg seal in seat on lever side;
-- fit the spool from the opposite side and till it is possible to
fit the other O--Ring seal;
-- position the spool in centre.
SD5
128 DAU003E
Malfunction Cause Remedy
External leakage pivot box lever or
control kit side.
Worn spool seal due to mechanical
actuation or high back pressure.
Locate the leakage and replace the seal.
Check back pressure level.
Excessive internal leakage on A and B
ports.
Increase clearance between spools and
body due to high wear.
Replace the directional control valve and
check the oil contamination level.
Pressure relief valve blocked open. Remove and clean or replace the valve.
I
n
a
b
i
l
i
t
y
t
o
b
u
i
l
d
p
r
e
s
s
u
r
e
o
n
A
a
n
d
B
Low pump pressure and flow. Check the pump and circuit.
I
n
a
b
i
l
i
t
y
t
o
b
u
i
l
d
p
r
e
s
s
u
r
e
o
n
A
a
n
d
B
ports.
Compensator spool is jammed.
Substitute the compensator spool and
verify the smoothness during assembly.
Check the oil contamination level.
The flow doesn’t vary at the working
ports by operating the flow regulator.
Control device of flow regulator is
damaged.
Substitute the flow regulator.
53
71
54.2
38.8
21.2
3P+T according to
ISO4400 / EN175301--803.
With bridge rectifier, to use with VAC supply.
Type C05 code: 2X1001080
PG09
2.13
2.09
2.79
1.53
0.83
30
1.18
3P+T according to
ISO4400 / EN175301--803
42.5
28.5
14
28
1
PG09
Type C03 code: 2X1001030
0.55
1.12
1.67
1.10
23.5
40.5
31.5
31.5
2P+T, according to EN175301--803
Type C01 code: 2X1001020
PG09
1.24
1.24
1.59
0.93
50
33
2P+T according to
ISO4400 / EN175301 --803
1
2
PG09
30
Type C02 code: 2X1001010
1.97
1.30
1.18
47
Accessories
Connectors
2 poles, type Packard “Weather Pack”
female housing with male ends
Type C17 code: 5CON005
24
2 poles, type AMP “Junior--Power--Timer”
female housing with female ends
Type C08 code: 5CON003
37.5
11.817
16
23
17.5
0
28.4
15
2 poles, type “Deutsch DT06--2S”
male housing with female ends
Type C19 code: 5CON007
40.5
21.3
2 poles, type Packard “Weather Pack”
male housing with female ends
Type C07 code: 5CON001
1.59
0.85
23
37
4 poles according to VDE0660 --0110
Type C11 code: 5CON006
13
16
PG07
0.51
1.46
0.91
0.63
1.85
0.95
1.12
0.59
0.63
0.91
0.67
0.69
1.48
0.46
SD5
129DAU003E
SD5
130 DAU003E
Type
Poles Nominal voltage
Nominal
current
Permitted conductor
section range
Permitted cable
diameter range
Weather
protection
C01 2P + T 250 VAC / 300 VDC 10 A max.1.5 mm
2
/ max.0.0023 in
2
6to8mm/0.24 to 0.31 in IP65
C02 2P + T 250 VAC / 300 VDC 10 A max.1.5 mm
2
/ max.0.0023 in
2
6to8mm/0.24 to 0.31 in IP65
C03 3P + T 250 VAC / 300 VDC 10 A max.1.5 mm
2
/ max.0.0023 in
2
6to8mm/0.24 to 0.31 in IP65
C05 3P + T 230 VAC 1.5 A max.1.5 mm
2
/ max.0.0023 in
2
6to8mm/0.24 to 0.31 in IP65
C06 3P + T 250 VAC / 300 VDC 6A max.0.75 mm
2
/ max.0.00116 in
2
3.5to6mm/0.14 to 0.24 in IP65
C07 2P / 20 A 1to2mm
2
/ 0.00155 to 0.0031 in
2
2.8to3.5mm/0.11 to 0.14 in IP67
C08 2P 250 VAC 12 A 0.5to1mm
2
/ 0.00077 to 0.00155 in
2
1.3to1.6mm/0.05 to 0.063 in IP65
C11 4P 50 VAC / 120 VDC 6A 0.14 to 0.5 mm
2
/ 0.00022 to 0.00077 in
2
4to7.5mm/0.16 to 0.29 in IP65
C17 2P / 20 A 1to2mm
2
/ 0.00155 to 0.0031 in
2
1.3to1.4mm/0.05 to 0.067 in IP67
C19 2P / 13 A 1to1.2mm
2
/ 0.00155 to 0.00186 in
2
2.2to3.5mm/0.088 to 0.14 in IP67
C20 2P / 14 A 0.8to1mm
2
/ 0.00124 to 0.00155 in
2
1.3to1.7mm/0.05 to 0.067 in /
C21 2P / 7A 0.3to0.8mm
2
/ 0.00046 to 0.0012 in
2
2.2to3mm/0.087 to 0.118 in /
C24 2P / 14 A 0.3to5mm
2
/ 0.00046 to 0.00077 in
2
1.4to1.7mm/0.055 to 0.067 in IP67
Accessories
27.5
23
2 pole, type “PACKARD Metri--Pack”
male housing with female ends
Type C20 code: 5CON017
32
17.3
2 poles, type “AMP Superseal”
male housing with female ends
Type C24 code: 5CON0031
22.9
15.2
2 poles, type “AMP Fastin--Faston”
female housing with male ends
Type C21 code: 5CON018
10
Connectors
Notes
SD5 valve can be supplied with one coat of black paint (CVN configuration).
Description example: SD5/2--P(JG3--120)/18L/18L/AET--<CVN>
NOTE -- For different colour consult Sales Department.
1.08
0.91
0.90
0.39
0.60
1.26
0.68
SD5
131DAU003E
DIMENSIONE “A”
Tipo valvola (mm)
ELN(NA) 67
ELP(NA) 90,5
ELT(NA) 92,5
ELN(NC) 63
SD5
132 DAU003E
