22
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Catalogue MSG30-8200/UK
Truck Hydraulics
F1 Pump - Fixed Displacement
F1 Pump
F1-ISO
Contents
Contents Page Chapter
Pump and Line selection ..............................................................................12 ................. 2
F1-25 to -101, ISO ........................................................................................23
Specifications and pump cross section ........................................................23
Installation Dimensions, F1-25, -41, -51 and -61 ..........................................24
Ordering code and standard versions ..........................................................24
Installation Dimensions F1-81 and -101 ....................................................... 25
Port size and standard versions ...................................................................25
F1-12 ISO with BSP port treads ...................................................................26
Specifications and pump cross section ........................................................26
Installation Dimensions, F1-12 with BSP port treads ................................... 27
Ordering code code and standard versions ..................................................27
Installation Dimensions, F1-25, to -101, all ports are BSP .......................... 28
Ordering code ...............................................................................................28
Suction fittings ..............................................................................................56 ............... 11
Installation and start up ................................................................................73 ............... 14
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
23
Catalogue MSG30-8200/UK
4
1 2 3 4 5 6 7 8 9
F1_stor_section_06-11-28.ai
Leif A.
Truck Hydraulics
F1 Pump - Fixed Displacement
Specifications
1. Input shaft 4. Housing 7. Piston with piston ring
2. Bearings 5. Timing gear 8. Cylinder barrel
3. Shaft seals 6. Barrel support 9. End cap
Pump cross section
F1-25 to -101, ISO
Technical Information
Frame size F1- 25 41 51 61 81 101
Displacement [cm
3
/rev] 25.6 40.9 51.1 59.5 81.6 102.9
Max flow
1)
[l/min] 78 104 125 143 180 216
Max operating pressure [bar] 400 400 400 400 400 400
Mass moment of inertia J [kgm
2
] 0,00274 0,00266 0,00261 0,00257 0,00532 0,00524
Shaft speed [rpm]
- short circuited pump (low press.)
3100 2700 2700 2700 2300 2300
- max selfpriming speed
2)
3050 2550 2450 2400 2200 2100
Torque
1)
[Nm] 163 260 324 378 518 653
Max input power
3)
[kW] 45 61 73 83 105 126
Weight [kg] 8.5 8.5 8.5 8.5 12.5 12.5
1) Theoretical values
2) Valid at an inlet pressure of 1.0 bar (abs.) when operating
on mineral oil at a viscosity of 30 mm
2
/s (cSt).
3) Max 6 seconds in any one minute.
NOTE:
For noise level information, contact Parker Hannifin
24
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Catalogue MSG30-8200/UK
F1_61_install_ny2.eps
Leif A./06-08-07
ROTATION
2226
22 26
M12x24
108
98
104
80
Ø13 (x4)
109
Spline shaft B8x32x36
(ISO 14/DIN 5462)
7
73
12
55
206
85
169
131
96
32
Truck Hydraulics
F1 Pump - Fixed Displacement
Ordering code
Example: F1- 81 - R
F1 frame size
25, 41, 51, 61, 81 or 101
Shaft rotation
R Righthand
L Left hand
NOTE: The pump does not include a
suction fitting; it must be ordered
separately. See chapter 11.
F1-25, -41, -51 and -61
Installation Dimensions
Suction
port
Pressure
port
Left hand
rotation
Right hand
rotation
Pressure port
Suction
port
Approx.
center of
gravity
27.8
Ø34.9
Ø80
(+0/-0.013)
1.85 +0.3/-0
167.5 163.5
NOTE! The suction port fitting
must be ordered
separately
56.5
Standard versions
Designation Ordering no.
F1-25-R 378 1024
F1-25-L 378 1025
F1-41-R 378 1040
F1-41-L 378 1041
F1-51-R 378 1050
F1-51-L 378 1051
F1-61-R 378 1060
F1-61-L 378 1061
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
25
Catalogue MSG30-8200/UK
F1_81_install_ny3.eps
Leif A./06-08-07
98
114
80
Ø13 (x4)
110
2528
25 28
M12x24
118
217
213
R
ROTATION
L
Al-Si10Mg
12
55
259
220
7
112
Spline B8x32x36
(ISO 14/DIN 5462)
144
108
63
119
29
Suction
port
Pressure port
Left hand
rotation
Right hand
rotation
Pressure port
Suction
port
NOTE! The suction port fitting
must be ordered
separately
1.85 +0.3/-0
Ø80
(+0/-0.013)
Ø34.9
27.8
Approx.
center of
gravity
Truck Hydraulics
F1 Pump - Fixed Displacement
NOTE: The pump does not include a
suction fitting; it must be ordered
separately. See chapter 11.
F1-81 and -101
Installation Dimensions
Standard versions
Designation Ordering no.
F1-81-R 378 1080
F1-81-L 378 1081
F1-101-R 378 1100
F1-101-L 378 1101
Port size
F1 frame size Pressure port
1)
-25
3
/
4
"
-41
3
/
4
"
-51
3
/
4
"
-61
3
/
4
"
-81
1"
-101
1"
1) BSP thread (fitting not included)
4
26
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Catalogue MSG30-8200/UK
1 2 3 4 5 6 7 8 9
1 End cap 4 Barrel housing 7 Bearing housing with flange
2 Cylinder barrel 5 Timing gear 8 Shaft seals
3Pistonwithpistonring 6Rollerbearings 9Inputshaft
F1-12 ISO with BSP port treads
Specifications
Pump cross section
Truck Hydraulics
F1 Pump - Fixed Displacement
Technical Information
Frame size F1- 12
Displacement [cm
3
/rev] 12
Max flow
1)
[l/min]
28
Max operating pressure [bar]
350
Shaft speed [rpm]
- short circuited pump (low press.)
3100
- max selfpriming speed 2300
Torque
1)
[Nm]
67
Max input power [kW]
16
Weight [kg] 6.7
1) Theoretical values
NOTE:
For noise level information, contact Parker Hannifin
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
27
Catalogue MSG30-8200/UK
F1_12_install_UK.eps
Leif A./03-06-13
Ø13 (x4)
106
98
104
80
144
73 53
48
114
206
191
12
40°
104
15
55
106
Spline B8x32x36
(ISO 14/DIN 5462)
ROTATION
89
10
Ordering code
Example: F1- 12 - R
F1 frame size 12
Shaft rotation
R Righthand
L Left hand
NOTE: The pump does not include a
suction fitting; it must be ordered
separately. See chapter 11.
F1-12 with BSP port treads
Pressure port
BSP 1/2"
Suction port
BSP 3/4"
M12x24 (thread)
8.5
Ø34.9
27.8
1.85 +0.3/-0
Truck Hydraulics
F1 Pump - Fixed Displacement
Ø80 (+0/-0.013)
Approx.
center of
gravity
Installation Dimensions
Standard versions
Designation Ordering no.
F1-12-R 378 2212
F1-12-L 378 2211
4
28
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Catalogue MSG30-8200/UK
ROTATION
Ø13 (x4)
98
104
80
109
131
32
22
26
22
26
Spline B8x32x36
(ISO 14/DIN 5462)
7
73
12
55
206
85
M12x24
108
F1_61_threads_ny.eps
Leif A./06-09-25
NOTE: The pump does not include a
suction fitting; it must be ordered
separately. See chapter 11.
F1-25, -41, -51 and -61 with BSP port treads
Truck Hydraulics
F1 Pump - Fixed Displacement
Ordering code
Example: F1- 61 - RB
F1 frame size
25, 41, 51, 61, 81 or 101
Shaft rotation/port threads
RB Righthand/BSP
LB Left hand/BSP
Pressure
port
Suction
port
Suction
port
Pressure
port
Left hand
rotation
Right hand
rotation
Approx.
center of
gravity
56.5
27.8
167.5
1.85 +0.3/-0
Ø34.9
Ø80 (+0/-0.013)
163.5
Installation Dimensions
Port size (all ports are BSP)
F1 frame size Pressure port
1)
Suction port
-25
3
/
4
"
1"
-41
3
/
4
"
1"
-51
3
/
4
"
1"
-61
3
/
4
"
1"
Standard versions
Designation Ordering no.
F1-25-RB 378 4024
F1-25-LB 378 4025
F1-41-RB 378 4040
F1-41-LB 378 4041
F1-51-RB 378 4050
F1-51-LB 378 4051
F1-61-RB 378 4060
F1-61-LB 378 4061
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
29
Catalogue MSG30-8200/UK
R
ROTATION
L
Al-Si10Mg
63
144
29
98
114
80
Ø13 (x4)
110
25 28
2528
12
55
259
7
112
Spline B8x32x36
(ISO 14/DIN 5462)
119
M12x24
118
217
213
Ordering code
Example: F1- 81 - RB
F1 frame size
25, 41, 51, 61, 81 or 101
Shaft rotation/port threads
RB Righthand/BSP
LB Left hand/BSP
F1-81 and -101 with BSP port treads
Truck Hydraulics
F1 Pump - Fixed Displacement
Ø34.9
Ø80 (+0/-0.013)
27.8
1.85 +0.3/-0
Pressure
port
Suction
port
Suction
port
Pressure
port
Left hand
rotation
Right hand
rotation
Approx.
center of
gravity
Installation Dimensions
NOTE: The pump does not include a
suction fitting; it must be ordered
separately. See chapter 11.
Port size (all ports are BSP)
F1 frame size Pressure port
1)
Suction port
-81 1" 1
1
/
4
"
-101 1" 1
1
/
4
"
Standard versions
Designation Ordering no.
F1-81-RB 378 4080
F1-81-LB 378 4081
F1-101-RB 378 4100
F1-101-LB 378 4101
4
30
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Catalogue MSG30-8200/UK
F1 Pump
F1-SAE
Truck Hydraulics
F1 Pump - Fixed Displacement
Index
Contents Page Chapter
Pump and Line selection ..............................................................................12 ................. 2
Specifications ...............................................................................................31
Pump cross section ......................................................................................31
Installation Dimensions, F1-25, -41, -51 and -61 (SAE) ...............................32
Ordering code (SAE) ....................................................................................32
Port size ........................................................................................................32
Suction fittings ..............................................................................................56 ............... 11
Installation and start up ................................................................................73 ............... 14
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
31
Catalogue MSG30-8200/UK
1 2 3 4 5 6 7 8 9
F1_61_SAE_cross_ny.eps
Leif A./04-07-06
1. Input shaft
2. Bearings
3. Shaft seal
4. Housing
5. Timing gear
6. Barrel support
7. Piston with
piston ring
8. Cylinder barrel
9. End cap
Pump cross section
NOTE: For noise level information,
contact Parker Hannifin.
Specifications
Truck Hydraulics
F1 Pump - Fixed Displacement
Technical Information
Frame size F1- 25 41 51 61
Displacement [cm
3
/rev] 25.6 40.9 51.1 59.5
[cu in/rev] 1.56 2.50 3.12 3.63
Max flow
1)
[l/min] 78 104 125 143
[gpm] 20.6 27.5 33.0 37.8
Max operating pressure [bar]
350 350 350 350
[psi] 5800 5800 5800 5800
Shaft speed [rpm]
- short circuited pump (low press.)
3100 2700 2700 2700
- max selfpriming speed
2))
3050 2550 2450 2400
Torque
1)
at 350 bar [Nm] 142 227 284 331
at 5000 psi [lbf ft] 105 168 210 244
Max input power
[kW] 45 61 73 83
[hp] 60 82 98 111
Weight [kg] 8.5 8.5 8.5 8.5
[lbs] 18.7 18.7 18.7 18.7
1) Theoretical values
2) Valid at an inlet pressure of 1.0 bar/15 psi
(abs.) when operating on mineral oil at a
viscosity of 30 mm
2
/s (cSt)/150 SUS.
4
32
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Catalogue MSG30-8200/UK
F1_SAE_ny5.eps
Leif A./06-08-07
R
ROTATION
L
Al-Si10Mg
M8
186
8
33
12
163
22
26
26
22
118
118
Spline shaft S (SAE J744b)
22-4, 13T, 16/32 DP;
206
85
167
130
98
32
56
Ordering code (SAE)
Example: F1- 61 - R U - S V - S
F1 frame size
25, 41, 51 or 61
Shaft rotation
R Righthand
L Left hand
Installation dimensions, F1-25, -41, -51 and -61 (SAE)
Dimensions in mm [inches]
Truck Hydraulics
F1 Pump - Fixed Displacement
NOTE: The pump does not include a suction
fitting; it must be ordered separately. See
chapter 11.
Shaft end
S SAE spline "B" spline
Shaft seal
V FPM
Mounting flange
S SAE "B"
Main port
U SAE O-ring, UN threads
[5.00 dia.]
The suction
port adpter
must be
ordered
separately
[8.11]
[6.57]
41.5
[1.63]
Suction
port
Right hand
rotation
Suction
port
Approx.
center of
gravity
pressure port
adapter (included);
tread: 1
1
/
16
"-12 UN
Left hand
rotation
89.8
[3.54]
[4.65]
Ø14.3 [0.56] (x4)
[4.65]
[2.22]
[5.13]
[3.86]
[1.26]
pressure port
adapter (included);
tread: 1
1
/
16
"-12 UN
[7.32]
[6.43]
[1.02] [0.86]
[0.86] [1.02]
[0.47]
[1.30]
14.5
[0.57]
[0.32]
9.5
[0.37]
Ø21.6 [0.850]
Ø101.60 (+0/-0.05)
[4.000 (+0/-0.002)]
[3.35]
Flange S
(SAE J744, 'B'
Spline according to
SAE J498b, class 1.
Installation Dimensions
Port size
F1 frame size Pressure port
1)
-25 1
1
/
16
"-12 UN
-41 1
1
/
16
"-12 UN
-51 1
1
/
16
"-12 UN
-61 1
1
/
16
"-12 UN
1) BSP-to-SAE adapter (included)
Standard SAE versions
Designation Ordering no.
F1-25-RU 378 1424
F1-25-LU 378 1425
F1-41-RU 378 1440
F1-41-LU 378 1441
F1-51-RU 378 1450
F1-51-LU 378 1451
F1-61-RU 378 1460
F1-61-LU 378 1461