Athalon™ maximum-life filters deliver the highest level of sustained fluid
system protection, across all applications, regardless of severity.
Featuring an industry leading Beta
X(C)
=2000* filter efficiency; the
highest rated filter performance available today.
(* per ISO 16889)
Notes and Specifications Filter Housing
• Flows to 600 L/min (160 US gpm)
• Pressures to 414 bar (6000 psi)
• Port size 1½”
• Rated Fatigue Pressure:
0-240 bar (3500 psi) per NFPA T2.06.01R2-2001 CAT C/90/*(1 million
cycles), verified by testing at 0-280 bar (4050 psi) for 1 million cycles.
Contact Pall for applications with higher pressures at lower cycles
• Filter Element Burst Pressure:
10 bard (150 psid)
• Fluid Compatibility:
Compatible with all petroleum oils and most water glycols, water-oil
emulsions, and synthetic hydraulic and lubrication fluids
• Temperature Range:
Fluorocarbon Seals:
-29 ˚C to 120 ˚C (-20 ˚F to 250 ˚F)
60 ˚C (140 ˚F) maximum in HWCF or water glycol fluids
• Bypass Valve Setting:
4.5 bard (65 psid)
• Indicator Pressure Setting:
3.5 bard (50 psid)
• Materials of Construction:
Head and Cover: Ductile Cast Iron
Tube: Carbon steel
• Filter Element :
Inorganic fibers impregnated and bonded with epoxy resins. Polymer
endcaps. Anti-static media design
New: UH310 Series
Athalon
TM
High Pressure Manifold Filters
Data Sheet M&EUH310MEN
Pressure Drop Information
Housing pressure drop using fluid with 0.9 S.G.
Housing pressure drop is directly proportional to specific gravity.
• Keeps fluids the cleanest, longest,
for the greatest value
• Provides consistent, reliable,
protection of system components
over the full service life of the filter
element
• Rapidly achieves and sustains
required fluid system cleanliness
• Delivers maximum filter capacity in
the smallest footprint
• Prevents electrostatic discharge
from damaging your filter and
degrading your fluid
Features
• Patented Ultipleat (laid-over pleat)
filter medium pack
• Pall Stress-Resistant Technology
(SRT) Media
• Coreless filter element
configuration
• Low clean pressure drop for low
energy operation
UH310 Series
Manifold mount
filter housing
Multiply actual flow rate times factor in table below to determine
pressure drop with fluid at 32 cSt (150 SUS), 0.9 S.G. Correct for
other fluids by multiplying new viscosity in cSt/32 (SUS/150) x new
S.G./0.9. Note: factors are per 1000 L/min and per 1 US gpm
Sample ∆P calculation
UH310 Series 13” length housing with K24 1 1/2” topmount flange
using AN grade media. Operating conditions 300 L/min flow rate using
a hydraulic fluid of 50 cSt and specific gravity (s.g.) 1.2.
Total Filter ∆P
= ∆P housing + ∆P element
= (0.58 x 1.2/0.9) bard (housing)
+ ((300 x 1.09/1000) x 50/32 x 1.2/0.9) bard (element)
= 0.77 (housing) + 0.68 bard (element)
= 1.45 bard (21.1 psid)
Length Code
08
13
20
40
AZ
5.52 (0.302)
3.31 (0.182)
2.18 (0.120)
1.10 (0.060)
AP
2.30 (0.126)
1.38 (0.076)
0.91 (0.050)
0.46
(0.025)
AS
1.32 (0.072)
0.79 (0.043)
0.52 (0.029)
0.26 (0.014)
AN
1.82 (0.100)
1.09 (0.060)
0.72 (0.040)
0.36 (0.020)
310 Series Filter Elements – bard/1000 L/min (psid/US gpm)
AT
0.82 (0.045)
0.49 (0.027)
0.33 (0.018)
0.16 (0.009)
Element Pressure Drop
0
5
15
20
0255075 100 125 175 200150
0
0.5
1.0
1.5
2.0
2.5
3.0
10
30
35
25
40
K24
S24
0 100 200 300 400 500 600 700
rP (psid)
rP (bard)
Flow (US gpm)
Flow (L/min)
Ordering Information
For new installations, select one complete
part number from each section below
Seal Kit P/N: SH 310 SKZ
*Other seal material options are available; Contact Pall.
Note: Pall Athalon filter housings are supplied without filter elements or
warning devices fitted. Never operate the filter unless a filter element is
fitted and all warning device ports are sealed.
Note: Z indicates fluorocarbon seals are standard. Other options are available;
contact Pall. Housing P/N designates indicator port fitted with a plastic shipping plug.
Housing P/N: UH310
Table A
Table B
Section 1
Code
K
S
Port Style
Top manifold mount
Side manifold mount
Table 1: Housing Port Options
Max. Operating Pressure
414 bar (6000 psi)
414 bar (6000 psi)
Code
24
Port Style
1 1/2” nominal
Table 2: Port Size
Code
G3
G3H
G6
G6H
C3
C6
Bypass Valve and Service Type
4.5 bard (65 psid) bypass valve, Cap service, metric port
4.5 bard (65 psid) bypass valve, Head service, metric port
4.5 bard (65 psid) bypass valve, Cap service, imperial port
4.5 bard (65 psid) bypass valve, Head service, imperial port
4.5 bard (65 psid) bypass valve with reverse flow, metric port
4.5 bard (65 psid) bypass valve with reverse flow, imperial port
Table 4: Bypass Valve and Service Options
Code
08Z
13Z
20Z
Length and Seal Material
8” nominal length, fluorocarbon seals
13” nominal length, fluorocarbon seals
20” nominal length, fluorocarbon seals
Table 3: Housing Length and Seal Options
K24087, G3, G6, C3, C6
K2420Z
S2408Z, G3, G6, G3H
S2413Z, G3, G6, G3H
S2420Z
Table A
Port & Length Options
Tables 1, 2 and 3
Table B
Bypass & Orientation Options
Tables 4
G3, G6, C3, C6
G3, G6, C3, C6
G6H, C3, C6
G6H, C3, C6
G3, G6, C3, C6
Section 2
Element P/N: UE 310
Table 5 Table 3
Note: Z indicates fluorocarbon seals are standard.
Other options are available; contact Pall.
* CST: Cyclic
Stabilization Test
to determine filter
rating under stress
conditions, based
on SAE ARP4205
Code
AZ
AP
AN
AS
AT
CST Rating*
07/04/01
11/08/03
13/09/04
15/11/06
16/14/08
ß
x(c)
≥2000 based on ISO 16889
3
5
7
12
25
Table 5: Filter Element Options
Section 3 (At least one Differential Pressure Indicator or
‘B’ type blanking plug must be ordered)
Differential Pressure Indicator P/N:
RC Z091 Z
Table 6 Table 7
Note: If no differential pressure indicator
is selected, ‘B’ type blanking plug (P/N
HC9000A104Z) must be ordered separately
and fitted to replace the plastic shipping plug.
Note: Z indicates fluorocarbon
seals are standard. Other
options are available;
contact Pall.
Code
Omit
SS
Pressure Setting
Brass Indicator
Stainless Steel Indicator: recommended for high pressure cycle
applications with pressure > 200 bar (3000 psi)
Table 7: Differential Pressure Indicator Material
Other setting options are available; contact Pall.
Code
A218M
A218R
A219D
Brass Option indicator
Electrical switch (SPDT) with Hirschmann connector
Electrical switch (SPDT) with Hirschmann connector
with Red and Green LED indicators
Visual indicator
Table 6: Indicator Options
Other options available; contact Pall.
* Requires YM suffix after SS code from Table 7.
Code
Stainless Steel indicator
778NZ Visual filter with thermal lockout
861CZ Electrical Switch (SPDT) with 6” leads
861CZ* Electrical switch (SPDT) with Hirschmann connector
771BZ Electrical switch (SPDT) with 3-pin
25 Harbor Park Drive
Port Washington NY 11050
+1 516 484 3600 telephone
+1 800 289 7255 toll free US
Portsmouth - UK
+44 (0)23 9233 8000 telephone
+44 (0)23 9233 8811 fax
Visit us on the Web at www.pall.com
Pall Corporation has offices and plants throughout the world. For Pall representatives
in your area, please go to www.pall.com/contact
Because of technological developments related to the products, systems, and/or
services described herein, the data and procedures are subject to change without
notice. Please consult your Pall representative or visit www.pall.com to verify that
this information remains valid.
© Copyright 2015, Pall Corporation. Athalon, Pall and are trademarks of Pall Corporation.
® Indicates a trademark registered in the USA. Better Lives. Better Planet and
Filtration. Separation. Solution.SM are service marks of Pall Corporation.
M&EUH310MEN Printed in the UK March 2016
Dimensional Drawings
Dimensions in mm (inches)
S24 OPTION
K24 OPTION
Length
Code
08
13
20
Overall length mm (in)
K Type Head
444.6 (17.50)
579.2 (22.80)
749.4 (29.50)
Cover Service Element Removal
Clearance mm (in)
248 (9.76)
383 (15.08)
553 (21.77)
Empty Weight kg (lb)
K Type Head
31.7 (69.9)
36.5 (80.5)
42.5 (93.9)
Head Service Element
Removal Clearance mm (in)
305 (12)
440 (17.32)
N/A
S Type Head
31.7 (69.9)
36.5 (80.5)
42.5 (93.9)
S Type Head
505.1 (19.89)
639.7 (25.19)
809.9 (31.89)
0.25
140
124
0.25
4X MOUNTING HOLES Ø23.0
TO SUIT M20 OR 7/8” UNC
BOLTS
OUTLET
INLET
INDICATOR
PORT
POSITION
197.5 mm
(7.78 in)
60 mm
(2.36 in)
102.5 mm
(4.04 in)
135.5 mm
(5.33 in)
152.5 mm
(6.00 in)
60 mm
(2.36 in)
102.5 mm
(4.35 in)
OVERALL LENGTH - SEE TABLE ABOVE
120 mm
(4.72 in)
132 mm
(5.2 in)
60 mm
(2.36 in)
66 mm
(2.6 in)
155 mm
(6.10 in)
Ø127 mm
(5.0 in)
VENT PLUG - TORQUE
TO 16/15Nm (12/11
LBFT) 1/4” OD TO SAE
J514 FOR VENT CODE
‘6’ G1/4” TO ISO228
FOR VENT CODE ‘3’
TORQUE 105/95Nm
(77/70 LBFT) COVER
INTO TUBE
BYPASS VALVE
172.3 mm MAX
(6.78 in)
2X 140 mm
(5.51 in)
2X 100 mm
(3.93 in)
82 mm
(3.23 in)
0.25
140
124
0.25
4X MOUNTING HOLES Ø23.0
TO SUIT M20 OR 7/8” UNC
BOLTS
mm
(4.88 in)
92.5 mm
(3.64 in)
2X 70 mm
(7.76 in)
57 mm
(2.24 in)
33 mm
(1.3 in)
99.4 mm
(3.91 in)
62 mm
(2.44 in)
2X mm
(5.5 in)
25 mm
(0.98 in)
0.25
140
124
0.25
(NOT SHOWN)
DRAIN PLUG - TORQUE TO 16/15Nm (12/11
LBFT) 1/4” OD TO SAE J514 FOR VENT CODE
‘6’ G1/4” TO ISO228 FOR VENT CODE ‘3’
INLET
OUTLET
HEAD
Ø127.0 mm
(5.0 in)
TORQUE 105/95Nm
(77/70 LBFT) COVER
INTO TUBE
VENT PLUG - TORQUE TO 16/15Nm (12/11 LBFT)
1/4” OD TO SAE J514 FOR VENT CODE ‘6’ G1/4”
TO ISO228 FOR VENT CODE ‘3’
OVERALL LENGTH - SEE TABLE ABOVE
MIN DISTANCE REQUIRED
FOR ELEMENT REMOVAL
4X Ø35.2/34.9
Ø155 mm
(6.10 in)
4X 100 mm
(3.94 in)
87.1 mm MAX
(3.43 in) MAX
87.1 mm MAX
(3.43 in) MAX
INDICATOR PORT
POSITION
BYPASS VALVE
18 mm (0.71 in)
137 mm
(5.39 in)
102 mm
(4.02 in)
103.5 mm
(4.07 in)
MIN DISTANCE REQUIRED
FOR ELEMENT REMOVAL
DRAIN PLUG - TORQUE
TO 16/15Nm (12/11
LBFT) 1/4” OD TO SAE
J514 FOR VENT CODE
‘6’ G1/4” TO ISO228 FOR
VENT CODE ‘3’