G761 Series Servovalves
ISO 10372 Size 04
The actual flow is dependent
upon electrical command signal
and valve pressure drop.The
flow for a given valve pressure
drop can be calculated using
the square root function for
sharp edge orifices:
∆p
Q = Q
N
∆p
N
Q gpm[l/min] = calculated flow
Q
N
gpm[l/min] = rated flow
∆p psi[bar] = actual valve
pressure drop
∆p
N
psi[bar] = rated valve
pressure drop
G761 SERIES SERVOVALVES
The G761 Series flow control
servovalves are throttle valves
for 3- and preferably 4-way
applications.They are a high
performance, two-stage design
that covers the range of rated
flows from 1 to 16.5 gpm at
1000 psi valve drop.The
output stage is a closed center,
four-way, sliding spool.The pilot
stage is a symmetrical double-
nozzle and flapper, driven by a
double air gap, dry torque
motor. Mechanical feedback of
the spool position is provided
by a cantilever spring.The valve
design is simple and rugged for
dependable, long life operation.
These valves are suitable for
electrohydraulic position,
speed, pressure or force con-
trol systems with high dynamic
response requirements.
Principle of operation
An electrical command signal
(flow rate set point) is applied
to the torque motor coils and
creates a magnetic force, which
acts on the ends of the pilot
stage armature.This causes a
deflection of armature/flapper
assembly within the flexure
tube. Deflection of the flapper
restricts fluid flow through one
nozzle, which is carried through
to one spool end, displacing
the spool.
Movement of the spool opens
the supply pressure port (P) to
one control port, while simul-
taneously opening the tank
port (T) to the other control
port.The spool motion also
applies a force to the cantilever
spring, creating a restoring
torque on the armature/flapper
assembly. Once the restoring
torque becomes equal to the
torque from the magnetic
forces, the armature/flapper
assembly moves back to the
neutral position, and the spool
is held open in a state of equi-
librium until the command sig-
nal changes to a new level.
In summary, the spool position
is proportional to the input
current.With constant pressure
drop across the valve, flow to
the load is proportional to the
spool position.
2
VALVE FEATURES
➣ 2-stage design with dry torque motor
➣ Low friction double nozzle pilot stage
➣ High spool control forces
➣ High dynamics
➣ Rugged, long-life design
➣ High resolution, low hysteresis
➣ Completely set-up at the factory
➣ Optional fifth port for separate pilot supply
➣ Field replaceable first stage disc filter
G761 SERIES
TWO STAGE SERVOVALVES
This catalog is for users with technical
knowledge.To ensure that all necessary
characteristics for function and safety
of the system are given, the user has
to check the suitability of the
products described here. In case
of doubt, please contact Moog Inc.
3
Operating Pressure
ports P, X, A and B up to 4,500 psi [315 bar]
port T up to 3,000 psi [210 bar]
Temperature Range
Fluid -20 to 275˚F [-29 to 135˚C]
Ambient -20 to 275˚F [-29 to 135˚C]
Seal Material* Fluorocarbon
Operating Fluid Compatible with common
hydraulic fluids, other fluids
on request.
Recommended viscosity 60 – 450 SUS @ 100˚F
System Filtration: High pressure filter (without bypass,
but with dirt alarm) mounted in the main flow and, if
possible, directly upstream of the valve. Refer to Moog
filtration catalog for recommended filtration scheme.
Class of Cleanliness: The cleanliness of the hydraulic fluid
greatly effects the performance (spool positioning, high
resolution) and wear (metering edges, pressure gain, leakage)
of the servovalve.
Recommended Cleanliness Class
For normal operation ISO 4406 < 14/11
For longer life ISO 4406 < 13/10
Filter Rating recommended
For normal operation ß
10
≥ 75 (10 µm absolute)
For longer life ß
5
≥ 75 (5 µm absolute)
Installation Operations Any position, fixed or movable.
Vibration 30 g, 3 axes
Weight 2.4 lb (4.0 lb for steel body)
Degree of Protection EN50529P: class IP65, with
mating connector mounted.
Shipping Plate Delivered with an oil sealed
shipping plate.
Flow Rate Q (gpm)
Valve Pressure Drop ∆p (psi)
40
30
20
10
5
2
1
0.5
200 400 600
2000 3000 4500
1000
5.0 gpm [19 lpm]
10.0 gpm [38 lpm]
16.5 gpm [63 lpm]
2.5 gpm [10 lpm]
1.0 gpm [4 lpm]
G761-3003
G761-3004
G761-3002
G761-3001
G761-3005
Valve Flow Diagram
Valve flow for maximum valve opening (100% command
signal) as a function of the valve pressure drop.
* Other seal material upon request
G761 SERIES
GENERAL TECHNICAL DATA
PA T BX
4
2
-4
-8
-10
0
-2
-6
10 100 1000
Amplitude Ratio (dB)
Frequency (Hz)
Frequency Response of
1, 2.5, 5 gpm Servovalves
120
100
80
60
40
20
0
Phase Lag (˚)
±40%
±100%
2
-4
-8
-10
0
-2
-6
10 100 1000
Amplitude Ratio (dB)
Frequency (Hz)
Frequency Response of
10 gpm Servovalves
120
100
80
60
40
20
0
Phase Lag (˚)
±40%
±100%
120
100
80
60
40
20
0
Time – milliseconds
36 912150
Control Flow – % rated
1
2
3
2
3
1, 2.5, 5 gpm
10 gpm
15 gpm
1
Frequency Response* Typical response charateristics for G761 series servovalves.
Step Response* Typical transient response of G761 series servovalves.
Model…Type G761-………
Mounting Pattern ISO 10372 - 04 - 04 - 0 - 92
Valve Body Version 4-way
2-stage with spool–bushing assembly
Pilot Stage Nozzle/Flapper
Pilot Connection Optional, Internal or External
Fluid Supply G761 series servovalves are intended
to operate with constant supply pressure
Supply Pressure Minimum 200 psi [14 bar]
Maximum Standard 4,500 psi [315 bar]
Proof Pressure at “P” Port 6,750 psi [473 bar]
at “T” Port 4,500 psi [315 bar]
Rated Flow Tolerance @ 1,000 psi ∆P
N
[%] ±10
Symmetry [%] < 10
Threshold* [%] < 0.5
Hysteresis* [%] < 3.0
Null Shift with Temp., 100˚F [55˚K] variation [%] < 2.0
with acceleration to 10 g < 2.0
For every 1,000 psi [70 bar] supply pressure change < 2.0
with return pressure 0 to 500 psi [0 to 35 bar] < 2.0
2
-4
-8
-10
0
-2
-6
10 100 1000
Amplitude Ratio (dB)
Frequency (Hz)
Frequency Response of
15 gpm Servovalves
120
100
80
60
40
20
0
Phase Lag (˚)
±40%
±100%
* Measured at 3,000 psi pilot or operating pressure
NOTE: High response is available, consult factory
G761 SERIES
TECHNICAL DATA
G761-3001, 3002, 3003 G761-3004 G761-3005
X
Y
F4
A
T
B
X
F2
G
P
F3
F1
5
PIN D
2.3
1.60
69.0
PIN B
1.30
3.68
81.0
.09
.327 [8.31]
EXTERNAL NULL ADJUST
2.11
2.3
DISC FILTER
.874
1.750
3.70
1.282
.531 [13.49]
22.20
X PORT
46.7
93.5
33.0
2.72
.53
2.11
.09
3.19
40.5
2.562
THRU
53.5
BEHIND COVER
PIN A
44.45
LOCATING PIN
65.07
.197 [5.00]
3/32 IN. HEX SOCKET
1.84
94.1
.008
ELECTRICAL
4X
32.56
[13.5]
[53.6]
CONNECTOR
PIN C
P PORT
Standard electrical
connector mates with
MS3106F14S-2S
or equivalent.
The mounting manifold
must conform to
ISO 10372-04-04-0-92.
Surface to which valve is
mounted requires a
32
[∆∆]
finish, flat within 0.001[0.03] TIR.
For external null adjust:
flow out of port B will increase
with clockwise rotation of null
adjust (3/32 hex key).
Flow bias is continually varied
for a given port as the null
adjust is rotated.
G761 SERIES
INSTALLATION DRAWINGS
CONVERSION INSTRUCTION
For operation with
internal or external
pilot connection.
P A B T X G F1 F2 F3 F4
Ø.32 Ø.32 Ø.32 Ø.32 Ø.2 Ø.14
5
/
16
-18
5
/
16
-18
5
/
16
-18
5
/
16
-18
X 0.87 0.44 1.31 0.87 1.31 0.48 0 1.75 1.75 0
Y 0.84 1.28 1.28 1.72 0.34 0.78 0 0 2.56 2.56
P A B T X G F1 F2 F3 F4
Ø8.2 Ø8.2 Ø8.2 Ø8.2 Ø5 Ø3.5 M8 M8 M8 M8
X 22.2 11.1 33.3 22.2 33.3 12.3 0 44.4 44.4 0
Y 21.4 32.5 32.5 43.6 8.7 19.8 0 0 65 65
U.S.
METRIC
*The standard version of these valves is configured as internal pilot supply.
Changing pilot supply configuration requires model number change.
Pilot flow Screw & Seal Washer Location (M4 X 6 DIN EN ISO 4762)
supply XP
Internal P* closed open
External X open closed
Rated current and
coil resistance
A variety of coils are
available for G761
Series Servovalves.
Coil connections
A four-pin electrical box
connector (that mates with
an MS3106F14S2S cable
connector) is standard.
All four torque motor leads
are available at the connector
so external connections can
be made for series, parallel
or single coil operation.
Servoamplifier
The servoamplifier responds
to input current, so a
servoamplifier that has
high internal impedance
(as obtained with current
feedback) should be used.
This will reduce the effects
of coil inductance and will
minimize changes due to
coil resistance variations.
6
ELECTRICAL
CONNECTIONS
Coil Resistance [Ω]
Rated Current [mA]
Coil Inductance @ 50 Hz [H]
Electrical Power [W]
Polarity for Valve Opening
P ➧ B, A ➧ T
Parallel
40
±40
0.18
.064
A and C (+)
B and D (-)
Series
160
±20
0.66
.064
A (+), D (-)
Single
80
±40
.22
0.128
A (+), B (-)
or C (+), D (-)
ABCD
ABCD
ABCD
Note: Before applying electrical signals the pilot stage has to be pressurized.
G761 SERIES
ELECTRICAL CONNECTIONS
(Examples with typical G761 series coils)
7
Moog Part Size Moog Part Number
FPM 85 Shore O-Rings (included in delivery),
for P,T, A and B ID 0.426 x 0.070[10.8 x 1.8] 42082-022
for X ID 0.364 x 0.070[9.25 x 1.8] 42082-013
Mating Connector, waterproof IP 65 (not included in delivery)
49054F14S2S(MS3106F14S-2S)
Flushing Block (not included in delivery) 55124
Moog Part Size Moog Part Number
Mounting Bolts (not included in delivery)
(4 pieces) 5/16 - 18 NC x 1-3/4 long A31324-228B
[M8-1.25 x 45 mm long] [B64929-8B45]
Field Replaceable Filter Kit (includes service manual) B52555RK201K1
Pilot Supply Screw M4 x 6 DIN EN ISO 4762 66098-040-006
Seal for Set Screw A25528-040
SPARE PARTS AND ACCESSORIES
G761 SERIES
ORDERING INFORMATION
SPARE PARTS AND ACCESSORIES
G761
• • • • • •
Optional Feature
Series specification
Model Number Type Designation
•••J••M•VP•
Model Designation
Assigned at the factory
Factory Identification (Revision Level)
Rated Flow
Q
N
gpm [lpm] at ∆P
N
= 500 psi [35 bar] per land
04 1.0 [4.0]
10 2.5 [10]
19 5.0 [19]
38 10.0 [38]
63 16.5 [63]
Maximum Operating Pressure (P) and Body Material
J 4,500 psi [310 bar] aluminum
Spool Position without Electrical Signal
M Mid-position
Main Spool Type
O 4-way / Axis cut / linear
D 4-way / +/-10% overlap / linear
Signals for 100% Spool Stroke
H ±7.5 mA (series)
L ±20 mA (series)
Z ±100mA (series)
Valve Connector
P Connector over P-side
B Connector over B-side
Seal Material
V Fluorocarbon
Pilot Connections
4 Internal
5 External
Pilot Stage
F Low Flow, Nozzle-Flapper, ≤ 10 lpm
G High Flow, Nozzle-Flapper, > 10 lpm
Valve Version
H High response 1 gpm/4 lpm - 10 gpm/38 lpm
S Standard response 16.5 gpm/63 lpm
STANDARD MODELS
Model
Rated Flow
(∆ 1,000 psi)
gpm lpm
G761-3001 H04JOFM4VPL 1 4 < 0.31 < 1.2 40 80
G761-3002 H10JOFM4VPL 2.5 10 < 0.38 < 1.5 40 80
G761-3003 H19JOGM4VPL 5 19 < 0.60 < 2.3 40 80
G761-3004 H38JOGM4VPL 10 38 < 0.60 < 2.3 40 80
G761-3005 S63JOGM4VPL 16.5 63 < 0.60 < 2.3 40 80
Internal Leakage
(at 3,000 psi)
gpm lpm
Rated Current
(Single Coil)
mA
Nominal Coil
Resistance
Ohms
Type Designation
Argentina
Australia
Austria
Brazil
China
England
Finland
France
Germany
India
Ireland
Italy
Japan
Korea
Luxembourg
Norway
Russia
Singapore
Spain
Sweden
USA
Industrial Controls Division
Moog Inc., East Aurora, NY 14052-0018
Telephone: 716/652-2000
Fax: 716/687-7910
Toll Free: 1-800-272-MOOG
www.moog.com
CDL6642 Rev F 500-340 0405