Manifold Accessories
®
HYDRAFORCE
8.500.1
HYDRAFORCE
.com
®
Orifice Diameter
0.1900
0.1875
HEX
0.25 (6.4)
3/8 - 16 UNC - 2A
ORIFICE PLUGS
Made from a hex socket plug, orifice plugs can be pre-drilled or ordered as blanks. Orifice diameters can be specified within a
range. See the Sizing Guide on catalog page 8.460.1.
Orifice Size
000 Blank (No Orifice) or . . .
XXX Specify Orifice Diameter
from .020 to .187
6112 __ __ __
To Order:
ORIFICE PLATES
STANDARD POSITION
INVERTED POSITION
0.215 - 0.250
(5,47 - 6,35)
0.44
(11,1)
HEX
0.195
(4,95)
Inch
(mm)
0.215 - 0.250
(5,47 - 6,35)
125
125
125
125
0.002 (0,05)
0.002 (0,05)
0.002 (0,05)
0.002 (0,05)
Dia. 0.505 - 0.515
(12,83 - 13,08)
Dia. 0.483 (12,27)
Dia. 0.505 - 0.515
(12,83 - 13,08)
SAE 06 Fitting
SAE 06 Fitting
Orifice Plate
Flow is regulated from a
hydraulic cylinder or motor,
to the control valve
Flow is regulated from the
control valve, to a hydraulic
cylinder or motor
Orifice Plate
R 0.030 (0,76) Max.
R 0.010 (0,25) Max.
Dia. 0.375 (9,53) Max.
Dia. 0.375 (9,53) Max.
Orifice Plates produce a higher restriction in one direction and a lower restriction in the other direction.
Orifice Plates
Orifice Dia.
0.037 ±0.002
0.046 ±0.002
0.059 ±0.002
0.030 ±0.002
0.120 ±0.002
0.156 ±0.002
0.032 ±0.002
Part No.
4500210
4500220
4500230
4531610
4531840
4531850
4536440
Note: Specify diameter in 0.001 inch
increments with a tolerance of ±0.001.
Minimum drill diameter is 0.020 in. Refer
to Sizing Guide on catalog page 8.460.1.
For smaller orifice sizes consult factory.
Orifice Size
000 Blank (No Orifice) or . . .
XXX Specify Orifice Diameter
from .020 to .156
6101 __ __ __
Orifice Diameter
0.156 in.
(3.9 mm) Ref
0.25 in.
(6.4 mm)
Ref
1/16-27 NPTF
Orifice Plug - Level Seal Plug
1/16" Taper - 6101 _ _ _
Orifice Plug -
3/8" Hex Socket - 6112 _ _ _
HydraForce offers a range of accessories that can be
used on its manifolds and housings. Port plugs, orifice
plugs, plates and discs, screen cartridges, pilot pistons,
and adaptor lock kits are among the offerings.
This section provides an overview of the accessories,
with part numbers and sizing information.
An Orifice Sizing Guide is available on catalog page
8.460.1. The Sizing Guide provides drill-through diameters
for orifices for given flow ranges and pressures. It is help-
ful for sizing both orifice discs and plugs.
SAE PORT PLUGS
Available in Hex Head or
Hex Socket Versions
Hex Head
O-Ring Boss Plug
Size
SAE 2
SAE 4
SAE 6
SAE 8
SAE 10
SAE 12
SAE 16
SAE 20
Part No.
6103102
6103104
6103106
6103108
6103110
6103112
6103116
6103120
Hex Socket
O-Ring Boss Plug
Size
SAE 2
SAE 4
SAE 6
SAE 8
SAE 10
SAE 12
SAE 16
SAE 20
Part No.
6103002
6103004
6103006
6103008
6103010
6103012
6103016
6103020
HOUSINGS AND ACCESSORY PRODUCTS
Manifold Accessories (cont’d)
8.500.2
HYDRAFORCE
.com
®
USASI SYMBOL
100
MESH
SCREEN
SCREEN CARTRIDGES
These 100-mesh screen cartridges are not recommended
substitutes for hydraulic filters. However, they are good low-
cost “rock catchers” for shielding control orifices, pilot lines, etc.
Use SCxx cartridges for flow from port 2 to port 1 only.
Part No.
5290210
5291210
5293601
Size
08
10
16
Model
SC08-20-0-N-100
SC10-20-0-N-100
SC16-20-0-N-100
8.500.3
Manifold Accessories (cont’d)
®
HYDRAFORCE
HYDRAFORCE
.com
®
PILOT PISTONS
Pilot pistons can be successfully applied in aluminum housings if the designer and the fabricator prepare the bore correctly.
Without
Seals
Part No.
7013380
7013300
7013340
With
Seals
Part No.
7013380S
7013300S
7013340S
Double Piston
Size
08
10
12
Size
08
10
12
16
Without
Seals
Part No.
7013280
7013200
7013360
7013170
With
Seals
Part No.
7013280S
7013200S
7013360S
7013170S
Cavity
VC08-PCV
VC10-PCV
VC12-PCV
VC16-PCV
Cavity
VC10-PCV
VC10-CBV
Cavity
VC08-DCV
VC10-DCV
VC12-DCV
Single Piston
Size
10
10
Without
Seals
Part No.
4542160
7030310
With
Seals
Part No.
4542160S
7030310S
Heavy Duty Piston
Includes oil passage in nose
for use with center-hole poppets.
See Pilot Piston Cavity details
in Catalog Section 9:
08-size cavities: section 9.108.1
10-size cavities: section 9.110.1
12-size cavities: section 9.112.1
16-size cavities: section 9.116.1
ADAPTOR LOCKDOWN KITS
Lockdown kits can be used to help prevent valves from backing out of their cavities. Kits include adaptor plate, lock washer and ma-
chine screw. HyPerformance™ valves, which have a larger hex size than comparable standard valves, use a special kit with clear
zinc, circular adaptor plates that can be readily distinguished from the adaptor lockdown plates for standard valves.
Valve Model Ref. Dim. Kit Part No.
MR10 1 in. 5399000
HyPerformance™ 1-1/16 in. 4605870
PV70 & ZL70 1-1/8 in. 4205140
SV12 1-1/8 in. 4205140
PD12 1-1/4 in. 5960110
PD16 1-1/2 in. 5960108
EP20 & PD42 1-7/8 in 5960109
Valves with 1-inch
Nominal Hex
1 in. 5965000
HOUSINGS AND ACCESSORY PRODUCTS
Manifold Accessories (cont’d)
8.500.4
HYDRAFORCE
.com
®
Model Code Spacer Length
Blank No Spacer
A1 0.125 (3 mm)
M 0.469 (12 mm)
Screw length is increasd as necessary to
accomodate spacer length.
ADAPTER LOCKDOWN KIT ORDERING INFORMATION
Adapter lockdown kits may be used to help retain valves in their cavities. Kits include adapter plate, lock washer, machine screw
and optional spacer.
XXXXXXX__ __ __ __ __
Model Code
Hex Size
0875 7/8
1000 1
1250 1-1/4
1500 1-1/2
1875 1-7/8
BASE PART NO.
Head Screw
Lock Washer
Adapter Plate
Flat Washer
1-1/8”
REF
Adapter Lockdown Kit for SV12 Valve - P/N 4205140
1/8 Internal Hex
Machine Screw
Lock Washer
Adaptor Plate
Optional Spacer
Adapter Lockdown Kit for HyPerformance Valves - P/N 4605870
