E 5.978.1.0/12.10
514
Proportional Pressure
Relief Valve
Metric Cartridge – 350 bar
PDBM06020
Poppet Type - Direct Operated
up to 10 l/min
up to 350 bar
The PDBM06020 is a direct-operated,
poppet type proportional pressure relief
valve.
If the pressure at port 1 rises above the
setting dened by the electrical control,
the valve opens and allows ow from
port 1 to port 2. As a function of the
electrical signal, the relief pressure at
port 1 can be set steplessly.
FEATURES
Excellent stability over the whole ow range
Very good dynamics
Exposed surfaces zinc-plated and corrosion-proof
Minimal wear and long service life due to hardened and ground valve
components
Coil seals protect the solenoid system
Wide variety of coils and connectors available
Low pressure drop due to CFD optimised ow-path
Patented design for guided poppet
Excellent dynamic performance
Screen protected measuring orice enhances safety
FUNCTION
SPECIFICATIONS
Operating pressure: max. 350 bar
Nominal ow: pressure range 070 bar...max.10 l/min
pressure range 210 bar...max. 6 l/min
pressure range 350 bar...max. 4 l/min
Internal leakage: < 0.1 cm³/min at 80% nominal pressure
Media operating temperature range: min. -20 °C to max. +100 °C
Ambient temperature range: min. -20 °C to max. +60 °C
Fluids: Hydraulic oil to DIN 51524 Part 1 and 2
Viscosity: min 7.4 mm²/s to max. 420 mm²/s
Filtration: Class 19/17/14 to ISO 4406 or cleaner
Installation: optional, vertical preferred
Material: Valve body: steel
Piston: hardened and
ground steel
Seals: NBR (standard)
FKM (optional)
Back-up rings: PTFE
Cavity: 06020 metric
Weights: Valve complete: 0.44 kg
Coil only: 0.22 kg
Electronics
Control currents: 850 mA; 18 Ohm (24V)
1750 mA; 4.1 Ohm (12V)
Dither frequency: 160 - 250 Hz
Hysteresis with dither: 2-4% of max. control current
Repeatability: ≤ 1.5% of max. pressure range
Hysteresis error: ≤ 2% of max. control current
Response sensitivity: ≤ 1% of max. control current
Note:
The PDBM06020 can also be supplied with an emergency pressure adjustment (version -01M).
This allows a mechanical pressure adjustment of the valve if the electrical signal is interrupted.
This adjustment should be used only in the case of electrical failure since the manual setting would
be additive to the electrical setting and the danger of equipment damage could develop.
In order to achieve optimal function, any trapped air should be vented with the bleed screw on the
face of the tube (not tted to version -01M).
E 5.978.1.0/12.10
515
MODEL CODE
PDBM06020 - 01 - C - N - 350 - 24 PG - 18.0
Basic model
Proportional
pressure relief valve
Type
01 = standard
Body and Ports*
C = Cartridge only
Seals
N = NBR
V = FKM
Pressure range
070 = up to 70 bar
210 = up to 210 bar
350 = up to 350 bar
Coil voltage
12 = 12 V (4.1 Ohm)
24 = 24 V (18 Ohm)
Coil connector
PG = DIN connector to EN175301-803
PL = leadwires (2) - 457 mm (18") long
PN = Deutsch connector, 2 pole
PU = AMP Junior Timer, 2 pole, axial
other connection types on request
Coil resistance
4.1 = 4.1 Ohm (12V)
18.0 = 18 Ohm (24V)
* Standard line bodies
Code Part No. Material Ports
R06020-01X-01 275266 Steel, zinc-plated G3/8
other housings on request
Seal kits
Code Part No.
Seal kit 06020-NBR 3119017
Seal kit 06020-FKM 3262477
Standard models
Model code Part No.
PDBM06020-01-C-N-070-12PG-4.1 3362793
PDBM06020-01-C-N-070-24PG-18.0 3362790
PDBM06020-01-C-N-210-12PG-4.1 3362794
PDBM06020-01-C-N-210-24PG-18.0 3362791
PDBM06020-01-C-N-350-12PG-4.1 3362825
PDBM06020-01-C-N-350-24PG-18.0 3258051
DIMENSIONS
CAVITY
06020
Form tools
Tool Part No.
Countersink (shank MK3) 170033
Reamer (shank MK2) 1000768
Tap 1002648
Plug gauge 168840
Torque 4
+2
Nm
After loosening knurled nut, coil can
be rotated through 360° and removed
SW24 hex.
Torque 25
+5
Nm
through
thick
tting depth
Millimeter
Subject to technical modications.
Venting screw
Torque 2,5
+0,5
Nm
Millimeter
Subject to technical modications.
E 5.978.1.0/12.10
516
PERFORMANCE
∆p-Q Graph
measured at:
ν = 34 mm
2
/s; T
Oil
= 46 °C
P-I Graph, Pressure range 70 bar
P-Q Graph, Pressure range 70 bar
P-I Graph, Pressure range 210 bar
measured at:
ν = 34 mm
2
/s; T
Oil
= 46 °C
measured at:
ν = 34 mm
2
/s; T
Oil
= 46 °C
measured at:
ν = 34 mm
2
/s; T
Oil
= 46 °C
Pressure drop l = 0 mA
ow rate
Pressure stage
350bar (5100 PSI)
Pressure stage
210bar (3050 PSI)
Pressure stage
70bar (1000 PSI)
Relieving Pressure
Relieving Pressure
max. solenoid current
ow rate
max. solenoid current
max. solenoid current
solenoid de-energised
Relieving Pressure
% of max. solenoid current
% of max. solenoid current
measured at:
ν = 34 mm
2
/s; T
Oil
= 46 °C
P-Q Graph, Pressure range 210 bar
measured at:
ν = 34 mm
2
/s; T
Oil
= 46 °C
P-I Graph, Pressure range 350 bar
measured at:
ν = 34 mm
2
/s; T
Oil
= 46 °C
P-Q Graph, Pressure range 350 bar
% of max. solenoid current
ow rate
Relieving Pressure
max. solenoid current
max. solenoid current
max. solenoid current
solenoid de-energised
Relieving Pressure
Relieving Pressure
max. solenoid current
solenoid de-energised
max. solenoid current
max. solenoid current
ow rate
HYDAC Fluidtechnik GmbH
Justus-von-Liebig-Str.
D-66280 Sulzbach/Saar
Tel: 0 68 97 /509-01
Telefax. 0 68 97 /509-598
The information in this brochure
relates to the operating conditions
and applications described. For
applications or operating conditions
not described, please contact the
relevant technical department.
Subject to technical modications.
NOTE
E 5.978.1.0/12.10
517