Directional valve
2-way/2-position
Q
max
= 80 l/min, p
max
= 350 bar
Pilot operated, poppet type, switching position monitored, switching solenoid
Type series: WSVP22GPR-SA-10F-_A…
– Screw-in cartridge valve for cavity HF/C1220A
– All external parts with zinc-nickel plating according to
DIN EN ISO 19598
– Installation in threaded port body type GHF-34
– With integral electronic monitoring of operating posi
tion
– With bidirectional seat-valve shut-off
– High pressure wet-armature solenoids
– The slip-on coil can be rotated, and it can be replaced
without opening the hydraulic envelope
– Various plug-connector systems and voltages are
available
Symbol
1
2
G
1
2
G
Simplified Detailed
Description
These 2/2 solenoid-operated cartridge valves, series
WSVP22GPR-SA-10F..., feature monitoring of the oper
ating positions and are size 10, two stage, high perform
ance screw-in cartridges with an 1 1/16-12 UN-2A
mounting thread. The main and pilot stages are both
designed on the poppet/seat principle, and they are
therefore virtually leak-free in both directions of flow.
The safe switch position is always the non-operated
valve position. To ensure that electrical line interrup
tions of any kind do not result in unsafe conditions,
the sensor's switch output is always at High in the
non-operated state. The safe switch position is consid
ered to have been reached when the spool is in the
overlap state. All external parts of the cartridge are
zinc-nickel plated and are thus suitable for use in
the harshest operating environments. The slip-on coils
can be replaced without opening the hydraulic circuit
or removing the electronics (sensor), and can be posi
tioned at any angle through 360°. These screw-in valves
are predominantly used in certain mobile and indus
trial applications where shut-off functions are crucially
important. Examples are where loads, tensions, or
clamping forces must be held without leakage, or where
an operating position must be monitored. If you intend
Type series: WSVP22GPR-SA-10F-_A… 1 / 6 Reference: 400-P-131109-EN-01/03.2025
to install the valve yourself, please refer to the section
"Related data sheets".
Technical data
General characteristics Description, value, unit
Function group directional valve
Function 2-way/2-position
Design screw-in cartridge valve
Controls switching solenoid
Characteristic pilot operated, poppet type, switching position monitored
MTTFd value 150 years
Construction size NG 10
Thread size 1 1/16-12 UN-2A
Mounting attitude unrestricted
Weight 0.72 kg
Cavity acc. factory standard HF/C1220A
Tightening torque steel 65 Nm
Tightening torque aluminium 50 Nm
Tightening torque tolerance ± 10 %
Minimum ambient temperature - 30 °C
Maximum ambient temperature + 50 °C
Surface protection
all external parts with zinc-nickel plating according to
DIN EN ISO 19598
Sealing material see ordering code
Seal kit order number NBR: DS-518-N / FKM: DS-518-V
Hydraulic characteristics Description, value, unit
Maximum operating pressure 350 bar
Maximum flow rate 80 l/min
Flow direction see symbol
Hydraulic fluid
HL and HLP mineral oil according to DIN 51 524;
other fluids on request!
Minimum fluid temperature - 30 °C
Maximum fluid temperature + 80 °C
Viscosity range 10 … 500 mm²/s (cSt)
Recommended viscosity range 15 … 250 mm²/s (cSt)
Minimum fluid cleanliness
(cleanlineless class according to ISO 4406:1999)
class 20/18/15
NOTE!
Slightly increased leakage is possible in dynamic
use in the lowest temperature range.
Type series: WSVP22GPR-SA-10F-_A… 2 / 6 Reference: 400-P-131109-EN-01/03.2025
Electric characteristics Description, value, unit
Actuator type solenoid coil
Solenoid coils type 36X48/16.1
Supply voltage DC 12/24 V DC
Supply voltage tolerance ± 10 %
Nominal power consumption 19 W
Switching time
Switching time measured at: UN: Δp = 280 bar; Q = 64 l/min;
TAmbient = 40 °C; ϑ = 46 mm2/s
2 to 1: 67 ms (energizing) / 96 ms (de-energizing)
1 to 2: 65 ms (energizing) / 65 ms (de-energizing)
Relative duty cycle 100 %
Electrical connection coil several connection types available, see ordering code
Protection class solenoid coil to ISO 20 653 / EN 60 529
several classes of protection available, see ordering code
(with appropriate mating connector and proper fitting and
sealing)
NOTE!
The switching time can be strongly dependent
on flow rate, pressure, oil viscosity and the dwell
time under pressure. In practice, the switching
time may therefore deviate from the specified
value range.
Sensor characteristics Description, value, unit
Supply voltage (+Vs) 10…30 V DC
Maximum load current 100 mA
Short-circuit protection Permanently resistant to load short circuit
Protection class sensor to ISO 20653 / EN 60529
IP 67 / IP 69K (with appropriate mating connector and proper
fitting and sealing)
Vibration test EN 60068-2-6 – 55 Hz, amplitude 1 mm, 3 axes, 30 min
Shock test
EN 60068-2-27 – half sine wave, 30 gn 11 ms half sine wave, 3
axes
EMC immunity EN 61000-6-2
EMC interference emission EN 61000-6-4
MTTF (40° C) according to EN ISO 13849-1 Annex C.5 320 years
MTTFD according to EN ISO 13849-1 Annex C.5.1 640 years
Electrical connection device plug M12x1, 4-pin (male), A-coded
Type series: WSVP22GPR-SA-10F-_A… 3 / 6 Reference: 400-P-131109-EN-01/03.2025
Performance graphs
measured with oil viscosity 33.0 mm²/s (cSt), coil at steady-state temperature and 10 % undervoltage
p = f (Q) Performance limit Δp = f (Q) Pressure drop-flow rate characteristic
400-PG-0797
Q [l/min (gpm)]
p [bar (psi)]
0 20 40 60 80
0
100 (1450)
200 (2900)
300 (4350)
350 (5000)
150 (2150)
250 (3600)
50 (725)
(5.25) (11) (16) (21)
400-PG-0798
30 (435)
80
p [bar (psi)]
Q [l/min. (gpm)]
0
0
25 (360)
20 (290)
15 (215)
10 (145)
5 (70)
(21)
70
(18)
60
(16)
50
(13)
40
(11)
30
(8)
20
(5.25)
10
(2.75)
1) 1 →2
2) 2
→1
2)
1)
Installation
49
[1.93]
27
[1.06]
33,15
[1.31]
35,5
[1.40]
9,2
[.36]
53
[2.09]
68
[2.68]
145
[5.71]
190
[7.48]
45
[1.77]
33,5
[1.32]
0.79 = 0.79 mm millimeter
[.031] = 0.031" inch
Beispiel für die Masseinheit:
Exampel for the dimensional units:
2
1
1 1/16-12 UN-2A
M = 2.7 [Nm] ±10%
(2ft-lbs
± 10%)
A
Ø18.77×1.78
Ø23.47×2.62
Ø16.00×2.00
Ø16.00×2.00
Ø17.30×1.40×1.40
Ø17.30×1.40×1.40
30
M = 1)
A
Type series: WSVP22GPR-SA-10F-_A…
4 / 6 Reference: 400-P-131109-EN-01/03.2025
NOTE!
1) When fitting the screw-in cartridge valve, use
the specified tightening torque. The value can be
found in the chapter "Technical data".
ATTENTION!
Only qualified personnel with mechanical skills
may carry out any maintenance work. Generally,
the only work that should ever be undertaken is
to check, and possibly replace, the seals. When
changing seals, oil or grease the new seals thor
oughly before fitting them.
ATTENTION!
Using screw-in valves and components that
include monitoring of the operating position: do
not use the signal from the position switch to
directly activate a safety-related control function.
In addition, only use solenoid coils that have a
protection diode.
ATTENTION!
The safe switch position is the non-operated
valve position. In accordance with the criteria for
proven safety principles, the status of the posi
tion signal changes during the overlap stroke
(before the valve actually opens).
IMPORTANT!
When connecting the sensor (for monitoring
the operating position), note the information
regarding pin assignment in this data sheet.
The sensor cable must not be subjected to any
pulling forces. Note also that opening the screw-
in valve or removing the electronics (sensor) is
not permitted!
NOTE!
To achieve the screw-in valve's maximum
performance rating, fit the solenoid coil as
shown (with the plug pins nearest the valve
body).
NOTE!
The seals are not available individually. The seal
kit order number can be found in the chapter
"Technical data".
Connection diagram for sensor
1
4
2
3
M
+Vs
Out 1
GND
not connected
Standard "A", 1 switching point:
Valve status
Unactivated
Actuated
Out 1 Out 2
high
low
-
-
Version A
Type series: WSVP22GPR-SA-10F-_A…
5 / 6 Reference: 400-P-131109-EN-01/03.2025
Ordering code
Ex.
directional valve
positive overlap
electrically operated, COIL 36X48, 19 W
bidirectional seat-valve shut-off
pilot operated
2-way/2-position function, de-energized closed
nominal size 10
cavity type HF/C1220A
NBR (nitril-butadien-rubber / BUNA) seals (standard)
FKM (fluorocarbon rubber / VITON) seals
Q = standard model according to valid data sheet
= special model (on request)
= technical design no. (omit by ordering)
PNP-normally closed, 1 switching point
with return spring for main spool
with operating-position monitoring
IMPORTANT!
mating
plug
not
supplied
voltage e.g. 24 (24 V)
current DC
DIN EN 175301-803 connection 3-pole 2 P+E, with protection diode, (IP 65) (standard)
Junior Timer plug connection 2-pole radial, with protection diode, (IP 65)
radial, with protection diode, (IP 67/69K)
(standard)
only connection “GR“ with mating plug
other plug-variants, please consult BUCHER.
22G
24
10
-
-
-
N
D
S
V
P
P
S
A
F
A
1
D
R
_
_
W
Related data sheets
Reference Description
400-P-040011 form tools
400-P-010101 MTTFd Values for Hydraulic Valves
400-P-120112 solenoid coil 36X48-161
400-P-065111 cavity HF/C1220A
400-P-740551 threaded port body GHF-34...
[email protected] www.bucherhydraulics.com
© 2026 by Bucher Hydraulics AG Frutigen, 3714 Frutigen, Switzerland
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense. The
information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to continual
improvement, we reserve the right to amend the product specifications contained in this catalogue.
Type series: WSVP22GPR-SA-10F-_A… 6 / 6 Reference: 400-P-131109-EN-01/03.2025