High performance directional valve, ISO size 05
Q
max
= 160l/min,p
max
= 315bar
Solenoid controlled, 2-stage
Series WEVDE…
1/5
Reference: 300-P-185110-EN-03
Issue: 09.2024
S High switching reliability thanks to 2-stage follower
spool operation
S Unaffected by:
- asymmetric flow path
- long periods under high pressure without switching
- large pressure drops across the spool lands
- low supply voltage
S High flow rates
S Good Dp-Q characteristics
S Pressure in P, A and B to 315 bar
S Wet armature design, change coils without opening
hydraulic envelope
S With manual override
S For subplate mounting, Interface ISO size 05 to
ISO 4401-05-04
1 Description
Series WEVDE ...-10 high performance spool valves are in
ternally piloted and use the follower spool principle. The
main valve components are a cast body, a spring-centered
follower spool assembly and wet armature solenoids with
pressure-tight core tube and slip-on coil. These valves pro
vide reliable service even under the severest operating con
ditions such as very high flow rates, high operating pres
sures, supply voltage drops, long periods without switching,
large and sudden changes in fluid temperature etc. The
highly effective spool actuation method combines the ad
vantages of direct acting and two-stage solenoid valves,
without incurring the well known disadvantages of either
type. The main spool is offset by both the solenoid force and
the P ⇒ T *) pressure difference inside the valve. The
greater the P ⇒ T pressure difference, the greater the offset
ting force. The spool is returned to the mid-position in the
same way, using the P ⇒ T pressure difference and without
the need for the usual heavy centering springs. If very low
flow rates, or an open circuit condition, result in there being
no P ⇒ T pressure difference, then the spool actuaction re
verts to the normal solenoid / centering spring arrangement.
*) The pressure in P must always be equal to, or greater
than, that in T and the valve must be connected in the con
ventional manner i.e. pressure to P, T to tank.
2 Symbols
1
WEVDE-42-A-10 WEVDE-42-AD-10
WEVDE-42-AG-10
WEVDE-42-BD-10
WEVDE-42-BG-10
WEVDE-43-D-10
WEVDE-43-G-10
AB
PT
a
AB
PT
b
AB
PT
a
AB
PT
b
A
B
PT
ba
WEVDE-42-B-10
AB
PT
a
AB
PT
b
AB
PT
ba
WEVDE-42-AH-10 WEVDE-42-BH-10 WEVDE-43-H-10
AB
PT
a
AB
PT
b
AB
PT
ba
2
3
8
9
4/2 FUNCTIONS
4/2 FUNCTIONS
WITH 4/3 SPOOLS
4/2 FUNCTIONS
WITH 4/3 SPOOLS
4/3 FUNCTIONS
Crossover transients
4
12
11
10
5
6
7
NOTE! Other spool types on request.
300-P-185110-EN-03/09.2024
Series WEVDE
2/5
3 Technical data
General characteristics Description, value, unit
Designation 4/2 and 4/3 solenoid controlled spool valves
Design combined direct acting and 2-stage
Mounting method mainfold mounting
Size nominal size 10 mm, 4401-05-04 size 5 interface
Mass 1 solenoid = 4.8 kg
2 solenoids = 6.3 kg
Mounting attitude horizontal recommended
(vertical mounting makes air bleeding difficult)
Hydraulic characteristics Description, value, unit
Maximum operating pressure P, A and B 315 bar
Maximum return pressure 160 bar
Maximum flow rate 160l/min
Flow direction see symbols
Hydraulic fluid HL and HLP mineral oil to DIN 51 524;
for other fluids, please contact BUCHER
Hydraulic fluid temperature range -30 °C … +80 °C
Ambient temperature range -30°C … +50°C
Viscosity range 10…500mm
2
/s (cSt), recommended 15...250mm
2
/s (cSt)
Minimum fluid cleanliness
Cleanliness class to ISO 4406:1999
class 20/18/15
Electrical characteristics Description, value, unit
Actuator type solenoid coil
Solenoid coils type pressure-tight wet armature design (slip-on coil system)
Supply voltage 12V DC, 24 V DC, 98 V DC, 196 V DC
(Other voltages on request)
196 V DV: DIN (can be used with rectifier for 230 AC)
Supply voltage tolerance ± 10 %
Nominal power consumption 39 W
Relative duty cycle 100%
Protection class to ISO20653 / EN60529 IP65 to DIN 40050
Electrical connection 3-pin square plug rotatable 4x90° to DIN 43650 / ISO 4400
300-P-185110-EN-03/09.2024
Series WEVDE
3/5
4 Performance graphs
measured with oil viscosity 33 mm
2
/s (cSt)
Δp-Q characteristics
→ Δp (bar)
P ⇒ A
P
⇒ B
P
⇒ T
A
⇒ T
B
⇒ T
-
-
-
-
A spool
D spool
G spool
H spool
3321
1211
1312
1222
Switching times
measured with: 24 VDC solenoid 5% under-
voltage, coil at steady-state temperature.
Solenoid ON
Solenoid OFF
45 ... 110 ms
20 ... 50 ms
These are guideline values only, and can be significantly
affected by flow rate and pressure.
To achieve switching times which are largely unaffected
by variations in supply voltage and coil temperature, we
recommend our type LRS Power Reducing connector
plug. Contact BUCHER for application assistance.
→ Q (l/min)
20 100
5
10
15
20
40 60 80 120 140 160
1
2
3
5 Installation information
ATTENTION!
All installation and servicing must be carried out
with care, and by qualified personnel only. When
servicing valves (cleaning, changing seals, etc.)
note the following:
A (and B) spools must not be reversed, or the
function P ⇒ A / B ⇒ T will become P ⇒ B / A ⇒
T (and vice versa). All other spools are symmetri
cal but should always be reassembled with their
original orientation, in any case.
IMPORTANT!: When changing seals, the new
seals should be thoroughly oiled or greased be
fore fitting them to the valve.
IMPORTANT!: Use the correct tightening torque
when fitting Spring cap, DC and Core tube.
IMPORTANT!: At installation, be sure to mount
the valve with its hydraulic ports mating with those
of the manifold block or subplate and, finally, use
the correct tightening torque for the 4 x M6 moun
ting screws.
300-P-185110-EN-03/09.2024
Series WEVDE
4/5
6 Dimensions & sectional view
Solenoid a
Solenoid a Solenoid b
ø 65
215
107
97 11
Solenoid b
ø 65
215
107
9711
13
approx. 113
71
36
30
10
to remove
Plug can be
turned 4x90°
Coil can be
secured at
any angle
through
360°
ø 65
107 97 107
311
21,5 54
46 12
Nameplate
Manual override
at solenoid end(s)
110
to remove
the coil
supplied complete with 4
hex. skt. cap screws M6 x 40.
Tightening torque
Ma = 8 ... 10 [ Nm ]
4/2 function, A valve
4/2 function, B valve
4/3 function
70
the plug
ø 15,6
1,3
P
AB
TT
ISO 4401 size 5 interface
PG9
PG9
PG9
PG9
7 Schematic section
Sealkit no. DS-146, comprising:
Itm. Qty. Description Size
1 5 O-ring no. 014 ∅ 12,42 x 1,78 N90
2 2 O-ring no. 118 ∅ 21,89 x 2,62 N90
3 2 O-ring ∅ 30,00 x 2,00 N70
4 2 O-ring ∅ 30,00 x 2,00 N70
Manual
override
36 A/F hex.
Tightening torque
Ma = 45 ... 55 Nm
27 A/F
Tightening torque
Ma = 45 ... 55 Nm
4
3
2
1
300-P-185110-EN-03/09.2024
Series WEVDE
5/5
8 Ordering code
9 Related data sheets
Reference Description
400-P-050101 Size 05 interface to ISO 4401-05-04
400-P-515101 LRSA DIN plug
E 2024 by Bucher Hydraulics AG Frutigen, CH-3714 Frutigen
www.bucherhydraulics.com[email protected]
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense. The
information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to continual
improvement, we reserve the right to amend the product specifications contained in this catalogue.
Classification: 430.300.300.305.305