Proportional 4/3 Throttle Cartridge, Size 10
Q
max
= 150 l/min,p
max
= 420bar
Sliding-spool design, hydraulic proportional
Series MDHP43…-10…
1/5
Reference: 400-P-630101-EN-00
Issue: 02.2021
S External hydraulic control
S Compact construction
for cavity type DZ – M36x2
S Two nominal volume flow rates
S Different spool options (center position)
S Symmetrical opening characteristics
(thanks to two separate tank ports)
S All exposed parts with zinc-nickel plating
1 Description
Series MDHP-43-10… hydraulically controlled proportional
4/3 throttle valves are size 10, high performance screw-in
cartridges with an M36x2 mounting thread. The sliding
spool is held in neutral position by the spring. As soon as the
pilot pressure of around 5 bar is reached, the spool starts to
open the connection from port 1 to the actuator (port 2 or 3).
The opening cross-section increases proportionally with in
creasing pilot pressure until the end position of the spool
and thus the maximum opening or flow rate is reached at ap
prox. 18 bar. Thanks to two separate tank ports (see sec
tional drawing), symmetrical opening characteristics are
reached on both sides. In addition to two spool designs (G
or D spool), there is a choice of two nominal flow rats with
defined pressure loss using a control edge in each case.
Thus, an optimal resolution of the opening cross-section
can be achieved for the application. These valves are pri
marily used in mobile and industrial applications where high
flow rates need to be controlled with high resolution. All ex
ternal parts of the cartridge are zinc-nickel plated according
to DIN EN ISO 19 598 and are thus suitable for use in the
harshest operating environments. For self-assembly,
please refer to the section related data sheets.
2 Symbol
2
41
3
5 6
2
41
3
5 6
MDHP43D… MDHP43G…
3 Technical data
General characteristics Description, value, unit
Designation proportional 4/3 throttle cartridge
Design sliding-spool design, hydraulic proportional
Mounting method screw-in cartridge M36x2
Tightening torque 250 Nm ± 10%
Size nominal size 10, cavity type DZ
Weight 1.05 kg
Mounting attitude unrestricted
Ambient temperature range -25°C … +50°C
400-P-630101-EN-00/02.2021
Series MDHP43…-10…
2/5
Hydraulic characteristics Description, value, unit
Maximum operating pressure - ports 1 to 4
- ports 5 and 6
420bar
30 bar
Maximum flow rate 150l/min
Nominal flow rate 80l/min at Δp = 10bar
100 l/min at Δp = 10bar
Flow direction see symbols
Hydraulic fluid HL and HLP mineral oil to DIN 51 524;
for other fluids, please contact BUCHER
Hydraulic fluid temperature range -25°C … +70°C
Viscosity range 15…380mm
2
/s (cSt), recommended 20...130mm
2
/s (cSt)
Minimum fluid cleanliness
Cleanliness class to ISO 4406:1999
class 18/16/13
4 Performance graphs measured with oil viscosity 33mm
2
/s (cSt)
Δp = f (Q) Pressure drop - Flow rate characteristic
P0580.ai
Q [l/min (gpm)]
5 (70)
0
10 (140)
15 (215)
20 (285)
25 (350)
30 (430)
0 25 50 75 100 125 150
(6.5) (13) (19) (26) (33) (39)
1)
2)
3)
4)
Q
N
= 100 l /minQ
N
= 100 l /min
Q
N
= 80 l /minQ
N
= 80 l /min
400-P-630101-EN-00/02.2021
Series MDHP43…-10…
3/5
Q = f (p
v
) Flow rate adjustment
[measured at Δp = 10 bar over
control edge 1 to 2 or 1 to 3]
2520151050
0
25 (6.5)
100 (26)
75 (19)
50 (13)
125 (33)
(70) (140) (215) (285) (350)
Q [l/min (gpm)]
p
v
[bar (psi)]
400−PG−P0581.ai
1)
1) Q
N
80 [l/min] ”D”, ”G” Kolben/spool
Q = f (p
v
) Flow rate adjustment
[measured at Δp = 10 bar over
control edge 1 to 2 or 1 to 3]
2520151050
0
25 (6.5)
100 (26)
75 (19)
50 (13)
125 (33)
(70) (140) (215) (285) (350)
Q [l/min (gpm)]
p
v
[bar (psi)]
1)
1) Q
N
100 [l/min] ”D”, ”G” Kolben/spool
400−PG−P0582.ai
5 Installation information
IMPORTANT!
When fitting the cartridges, the tightening torque
of the fixing screws must be considered. No ad
justments are necessary, since the cartridges are
set in the factory.
ATTENTION!
Only qualified personnel with mechanical skills
may carry out any maintenance work. Generally,
the only work that should ever be undertaken is to
check, and possibly replace, the seals. When
changing seals, oil or grease the new seals tho
roughly before fitting them.
400-P-630101-EN-00/02.2021
Series MDHP43…-10…
4/5
6 Dimensions & sectional view
43
169
126
4
3
1
2
4
5
6
4
3
2
1
41
M36X2
Seal kit NBR/PU no. DS-513-NU
Item Qty. Description
1 2 O-ring no. 119 ∅23, 47x2,62 PU92
2 2 O-ring no. 120 ∅25,07x2,62 PU92
3 2 O-ring no.121 ∅26,64x2,62 PU92
4 1 O-ring no.124 ∅31,42x2,62 N90
400-P-630101-EN-00/02.2021
Series MDHP43…-10…
5/5
7 Ordering code
M P
M = flow-control valve
D = throttle function, direct acting
H = hydraulically operated
P = proportional
43D = 4-way/3-position, spool type D
43G = 4-way/3-position, spool type G
Z = cavity type DZ
A = standard model - see relevant data sheets
Z = special features - please consult BUCHER
10 = nominal size 10
U = PU (Polyurethane) seals and NBR (Nitrile) seals (standard)
(special seals - please consult BUCHER)
80 = 80 l/min Q
N
1-2 / 1-3 at Δp = 10 bar
100 = 100 l/min Q
N
1-2 / 1-3 at Δp = 10 bar
0518 = actuation range (set pressure range)
1 ... 9 = design stage (omit when ordering new units)
-
Ex.
H
43D
ZD
-
0518 1
10
A
U80
-
-
8 Related data sheets
Reference (Old no.) Description
400-P-060291 (i-33.12) Cavity type DZ
E 2021 by Bucher Hydraulics AG Frutigen, CH-3714 Frutigen
www.bucherhydraulics.com[email protected]
All rights reserved.
Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense. The
information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to continual
improvement, we reserve the right to amend the product specifications contained in this catalogue.
Classification: 430.310.325.305.310.310