Subject to change · 40.55-e · 0215
Page 1
www.argo-hytos.com
HD 152 · HD 172
In-line mounting · Operating pressure up to 630 bar · Nominal flow rate up to 190 l/min
High Pressure Filters – Worldline 200
Description
Application
In the high pressure circuits of hydraulic systems.
Performance features
Protection against wear:
By means of filter elements that, in full-flow filtration, meet even
the highest demands regarding cleanliness classes.
Protection against malfunction:
Through installation near to the control valves or other expensive
components. The specific determined flow rate guarantees a
closed by-pass valve even at ν ≤ 200 mm
2
/s (cold start conditi-
on).
Filter elements
Flow direction from outside to centre. The star-shaped pleating
of the filter material results in:
› large filter surfaces
› low pressure drop
› high dirt-holding capacities
› long service life
Filter maintenance
By using a clogging indicator the correct moment for main-
tenance is stated and guarantees the optimum utilization of the
filter life.
Materials
Filter head: Spheroidal graphite cast iron (SGI)
Filter bowl: Cold extruded steel
Coating: Powder paint
Seals: NBR (FPM on request)
Filter media: EXAPOR
®
MAX 2 - inorganic multi-layer
microfibre web
Paper - cellulose web, impregnated with resin
Accessories
If an electrical indicator is used a transparent socket with LED for
optical indication is also available with Part No. DG 041.1200.
High Pressure Filter HD 172
Page 2
www.argo-hytos.com
Subject to change · 40.55-e · 0215
Characteristics
Operating pressure
0 ... 400 bar, min. 2 x 10
6
pressure cycles
Nominal pressure according DIN 24550
0 ... 630 bar, min. 10
4
pressure cycles
Quasi-static operating pressure
Permissible pressures for other numbers of cycles
Nominal flow rate
Up to 190 l/min (see Selection Chart, column 2)
The nominal flow rates indicated by ARGO-HYTOS are based on
the following features:
› closed by-pass valve at ν ≤ 200 mm
2
/s
› element service life > 1000 operating hours at an average
fluid contamination of 0,07 g per l/min flow volume
› flow velocity in the connection lines:
up to 250 bar ≤ 8 m/s
> 250 bar ≤ 12 m/s
Number of cycles n
Operating pressure p [bar]
Filter fineness
5 µm(c) ... 30 µm(c)
β-values according to ISO 16889
(see Selection Chart, column 4 and diagram Dx)
Dirt-holding capacity
Values in g test dust ISO MTD according to ISO 16889
(see Selection Chart, column 5)
Hydraulic fluids
Mineral oil and biodegradable fluids
(HEES and HETG, see info-sheet 00.20)
Temperature range
-30 °C ... +100 °C (temporary -40 °C ... +120 °C )
Viscosity at nominal flow rate
› at operating temperature: ν < 60 mm
2
/s
› as starting viscosity: ν
max
= 1200 mm
2
/s
› at initial operation:
The recommended starting viscosity can be read from the
diagram D (pressure drop as a function of the kinematic
viscosity) as follows: Find the 70 % ∆p of the cracking
pressure of the by-pass valve on the vertical axis. Draw a
horizontal line so that it intersects the ∆p curve at a point.
Read this point on the horizontal axis for the viscosity.
Mounting position
Preferably vertical, filter head on top
Connection
Threaded ports according to ISO 228 or DIN 13. Sizes see Selecti-
on Chart, column 6 (other port threads on request).
Electrical clogging indicator
› Switching voltage: max. 120 V AC / 175 V DC
› Switching current: max. 0,17 A AC / 0,25 A DC
› Switching power: max. 3,5 VA AC / 5 W DC
› Type of contact: Change-over
› Electrical protection: IP 65 (with mounted and secured
socket)
Page 3
www.argo-hytos.com
Subject to change · 40.55-e · 0215
Diagrams
∆p-curves for complete filters in Selection Chart, column 3
D1
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
0
1,0
0,5
1,5
HD 152
1
0
25 50 75 125100 150 175 200
2
4
5
3
∆p [bar]
Q [l/min]
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
2,5
5,0
7,5
10,0
12,5
15,0
1
4
2
5
3
200 400 600
800
1000
∆p [bar]
ν [mm
2
/s]
D2
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
0
1,0
0,5
1,5
HD 172
1
0
25 50 75 125100 150 175 200
2
4
5
7
6
3
∆p [bar]
Q [l/min]
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
1+3
4
4
7
6
6
2
5
200 400 600
800
1000
2,5
5,0
7,5
10,0
12,5
15,0
∆p [bar]
ν [mm
2
/s]
Dx
Filter fineness curves in Selection Chart, column 4
Filtration ratio β as a function of particle size x obtained
by the Multi-Pass Test according to ISO 16889
The abbreviations represent the following β-values resp.
finenesses:
For EXAPOR
®
MAX2 and Paper elements:
5EX2 = β
5 (c)
= 200 EXAPOR
®
MAX 2
7EX2 = β
7 (c)
= 200 EXAPOR
®
MAX 2
10EX2 = β
10 (c)
= 200 EXAPOR
®
MAX 2
16EX2 = β
16 (c)
= 200 EXAPOR
®
MAX 2
30P = β
30 (c)
= 200 Paper
Based on the structure of the filter media of the 30P paper
elements, deviations from the printed curves are quite probable.
For screen elements
40S = screen material with mesh size 40 µm
60S = screen material with mesh size 60 µm
100S = screen material with mesh size 100 µm
Tolerances for mesh size according to DIN 4189
For special applications, finenesses differing from these curves
are also available by using special composed filter media.
Filtration ratio β for particles > x µm
Particle size x [µm] (for particles larger
than the given particle size x)
Efficiency [%]
Page 4
www.argo-hytos.com
Subject to change · 40.55-e · 0215
Selection Chart
Remarks:
› The filters listed in this chart are standard filters. If modifications are required, e.g. connections SAE ¾ resp. SAE 1
(6000 psi), we kindly ask for your request.
› If an electrical indicator is used a transparent socket with LED for optical indication is also available with Part No. DG 041.1200.
Part No.
Nominal flow rate
Pressure drop see
diagram
D/
curve no.
Filter fineness see diagr.
Dx
Dirt-holding capacity
Connection A/B
Cracking pressure of by-pass
Symbol
Replacement filter element
Part No.
Weight
Clogging indicator
Cracking pressure in ( )
Remarks
l/min g bar kg bar
1 2 3 4 5 6 7 8 9 10 11 12
HD 152-186 110 D1/1 10EX2 13 G¾ - 6 V3.0617-26
1
7,1 electrical (5) change-over
HD 152-166 125 D1/2 10EX2 17 G¾ 7 1 V3.0617-06 6,9 - -
HD 152-276 125 D1/2 10EX2 17 G¾ 7 2 V3.0617-06 7,0 optical (5) -
HD 152-156 125 D1/2 10EX2 17 G¾ 7 3 V3.0617-06 7,0 electrical (5) change-over
HD 152-188 150 D1/3 16EX2 14 G1 - 6 V3.0617-18
1
7,1 electrical (5) change-over
HD 152-168 175 D1/4 16EX2 17 G1 7 1 V3.0617-08 6,9 - -
HD 152-278 175 D1/4 16EX2 17 G1 7 2 V3.0617-08 7,0 optical (5) -
HD 152-158 175 D1/4 16EX2 17 G1 7 3 V3.0617-08 7,0 electrical (5) change-over
HD 152-151 130 D1/5 30P 8,7 G1 7 1 P3.0617-01
2
6,9 - -
HD 152-261 130 D1/5 30P 8,7 G1 7 2 P3.0617-01
2
7,0 optical (5) -
HD 172-189 80 D2/1 5EX2 16 G1 - 6 V3.0623-13
1
8,4 electrical (5) change-over
HD 172-163 110 D2/2 5EX2 17 G1 7 1 V3.0623-03 8,0 - -
HD 172-273 110 D2/2 5EX2 17 G1 7 2 V3.0623-03 8,1 optical (5) -
HD 172-153 110 D2/2 5EX2 17 G1 7 3 V3.0623-03 8,1 electrical (5) change-over
HD 172-186 140 D2/3 10EX2 18 G1 - 6 V3.0623-26
1
8,4 electrical (5) change-over
HD 172-166 160 D2/4 10EX2 23 G1 7 1 V3.0623-06 8,0 - -
HD 172-276 160 D2/4 10EX2 23 G1 7 2 V3.0623-06 8,1 optical (5) -
HD 172-156 160 D2/4 10EX2 23 G1 7 3 V3.0623-06 8,1 electrical (5) change-over
HD 172-188 180 D2/5 16EX2 19 G1 - 6 V3.0623-18
1
8,4 electrical (5) change-over
HD 172-168 190 D2/6 16EX2 25 G1 7 1 V3.0623-08 8,0 - -
HD 172-278 190 D2/6 16EX2 25 G1 7 2 V3.0623-08 8,1 optical (5) -
HD 172-158 190 D2/6 16EX2 25 G1 7 3 V3.0623-08 8,1 electrical (5) change-over
HD 172-151 150 D2/7 30P 14 G1 7 1 P3.0623-11
2
8,0 - -
HD 172-261 150 D2/7 30P 14 G1 7 2 P3.0623-11
2
8,1 optical (5) -
1
Filter element differential pressure stable up to 160 bar
2
Paper media supported with metal gauze
Page 5
www.argo-hytos.com
Subject to change · 40.55-e · 0215
Dimensions
G
E
A
B
ØC
ØC
ØH
K
ØR
P
S
Q
S
Q
L
N
O
M
M
M
V
ersion wit
h
integrate
d
optica
l
c
l
o
gg
in
g
in
d
icator
Version with integrated electrical clogging indicator
SAE-
f
lange (6000 psi)
Minimum distance from
ferromagnetic parts: 7 mm
E
E
F
Terminal connection
I
D
Measurements
Type A/B C D E F G H I K L M
Ø/depth
N O P Q
opt./electr.
R S
opt./electr.
HD 152 G¾, G1 36, 45 224 39 66 104 75 70 AF27 60 M10/12 35 17,5 30 69/86 102 24/30
HD 172 G1 45 285 39 66 104 75 70 AF27 60 M10/12 35 17,5 30 69/86 102 24/30
Symbols
2 3 4 5 6 7
1
Page 6
www.argo-hytos.com
Subject to change · 40.55-e · 0215
Spare Parts
4
3
2
1
5
7
6
Pos. Designation Part No.
1 Filter bowl HD 152 HD 152.0102
1 Filter bowl HD 172 HD 171.0102
2 O-ring 63 x 3,5 N007.0634
3 Filter element see Chart/col. 9
4 Reed switch with screws and
socket (Pos. 5)
HD 049.1410
5 Socket DIN 43650 - AF3 DG 041.1220
6 Optical indicator (with Pos. 7) HD 049.1400
7 O-ring 17 x 2 N007.0172
The functions of the complete filters as well as the outstanding
features of the filter elements assured by ARGO-HYTOS can only
be guaranteed if original ARGO-HYTOS spare parts are used.
Quality Assurance
Quality management according to DIN EN ISO 9001
To ensure constant quality in production and operation, ARGO-HYTOS filter elements undergo strict controls and tests according to
the following ISO standards:
ISO 2941 Verification of collapse/burst pressure rating
ISO 2942 Verification of fabrication integrity (Bubble Point Test)
ISO 2943 Verification of material compatibility with fluids
ISO 3968 Evaluation of pressure drop versus flow characteristics
ISO 16889 Multi-Pass-Test (evaluation of filter fineness and dirt-holding capacity)
ISO 23181 Determination of resistance to flow fatigue using high viscosity fluid
Before release into the series production the filter casing is tested for fatigue strength in our pressure pulse test rig.
Various quality controls during the production process guarantee the leakfree function and solidity of our filters.
Illustrations may sometimes differ from the original. ARGO-HYTOS is not responsible for any unintentional mistake in this specification sheet.