Page 241
www.argo-hytos.com
E 598 · E 998
Tank top mounting · Connection up to -24 SAE and SAE 2½ · Nominal fl ow rate up to 850 l/min / 224.6 gpm
Return-Suction Filters
Description
Application
For operation in units with hydrostatic drives, when the return
fl ow is under all operating conditions higher than the oil fl ow of
the boost pump.
Performance features
Protection against wear:
By means of fi lter elements that even in full-fl ow fi ltration meet
the highest demands regarding cleanliness classes.
Suction fi lter function:
Because of the 100%-fi ltration of the suction fl ow, no dirt can
get into the boost pump.
Return fi lter function:
By means of full-fl ow fi ltration in the system return, the pumps
above all are protected from dirt particles remaining in the
system after assembly, repairs, or which are generated by wear
or enter the system from outside.
Return Suction Filter E 998
Subject to change · 20.98-EN/US · 0818
Page 242
www.argo-hytos.com
Function (schematic):
B
A
4
5
6
3
A
B
1
2
3
6
Emergency-suction (schematic):
Functional characteristics
The hydraulic oil returning from the circuit (A) passes the filter
element (1), is pressurized by a 0.5 bar / 7.3 psi check valve (2)
and supplied to the boost pump (B). The surplus oil flows filtered
over the integral check valve into the reservoir.
As the boost pump is always fed with pressurized oil, the risk of
cavitation is minimized and full performance is available even
during the critical cold start phase.
Six integral pressure relief valves (3) prevent too high back
pressure and protects the shaft seals against damages. As this
valves lead the oil directly into the tank there is no direct
connection between the return line (A) and the connection of
the boost pump (B) (no by-pass valve function).
The emergency-suction valve (4) with 200 µm protection strainer
(5) supplies the boost pump in case of a short term of lack of oil.
During normal operation, a lack of oil may definitely not occur
(refer to “Design“ section).
Start-up / De-aeration
At first start-up or at start up after repair, deaerating instructions
published by the manufacturers of hydraulic drives must be
observed.
Filter maintenance
By using a clogging indicator the correct moment for main-
tenance is indicated and guarantees therefore the optimum
utilization of the filter elements.
Filter elements
Flow direction from outside to the center.
The star-shaped pleating of the filter material results in:
› large filter surfaces
› low pressure drop
› high dirt-holding capacities
› long service life
The dirt collection bowl (6) prevents dirt particles accumulated at
the filter element from entering into the tank during maintenance.
Accessories
Electrical and / or optical clogging indicators are available.
Dimensions and technical data see catalog sheet 60.20.
Description
Subject to change · 20.98-EN/US · 0818
Page 243
www.argo-hytos.com
Layout
General
In machines with a hydrostatic drive and combined working
hydraulic system, return-suction filters replace the suction or
pressure filters previously required for the feed pump of the
closed-loop hydrostatic drive circuit as well as the return filter
for the open-loop working hydraulic circuit.
While each circuit operates independently with separate filters,
the combination of the two circuits via the return-suction filter
causes interaction between the circuits. If the design criteria
described below are taken into account, you can take full
advantage of the benefits provided by the return-suction filter
concept, thus making sure that your system performs reliably
even under extreme operating conditions.
Required return flow in the system
› In order to maintain a pre-charge pressure of approx.
0.5 bar / 7.3 psi at the intake of the feed pump, the return
flow must exceed the suction flow under any operating
conditions:
› Versions with hole (Ø 8 mm / 0.32 inch) in the pressurizing
valve: at least 30 l/min / 7.9 gpm of excess flow
Permitted feed pump flow rate
› at operating temperature
(ν < 60 mm
2
/s / 280 SUS, rpm = max):
feed pump flow rate < 0.5 x rated return flow according to
column 2 of selection table
› at cold start-up
(ν < 1000 mm
2
/s / 4635 SUS, rpm = 1.000 min
-1
):
feed pump flow rate < 0.2 x rated return flow according to
column 2 of selection table.
Please contact us if your system operates with higher flow rates
than stated above.
Flow velocity in the connecting lines
› Flow velocity in the return lines ≤ 4.5 m/s / 14.8 ft/s
› Flow velocity in the suction lines ≤ 1.5 m/s / 4.9 ft/s
Permitted pressure in the suction lines
At cold start up (ν < 1000 mm
2
/s / 4635 SUS, rpm = 1.000 min
-1
):
feed pump flow rate ≤ 0.2 x rated return flow. The pressure loss
in the suction lines must not exceed 0.4 bar / 5.8 psi.
Backpressures in system return lines
If drain oil from the hydrostatic drive is routed across the filter in
addition to the flow of the open-loop circuit, the following has
to be observed in order to protect the shaft seals:
› permitted leakage oil pressure for a given viscosity and speed
(manufacturer’s specifications!)
› pressure loss caused by the leakage oil pipes
› pressure loss caused by the oil cooler used
› backpressure of the filter for a given flow rate or kinematic
viscosity (refer to pressure loss diagrams)
Depending on the application, the use of a cooler by-pass valve
is recommended.
Generously sized drain oil pipes are also of advantage.
Filter fineness grades
With the filter fineness grades available, the following oil
cleanliness according to ISO 4406 can be achieved:
› 10EX2: 18/15/11 ... 14/11/7
› 16EX2: 20/17/12 ... 17/14/10
Even with the 16EX2 filter fineness grade, the requirements
specified by manufacturers of hydrostatic drives are sometimes
exceeded significantly. If components requiring a still better oil
purity are used, we recommend the 10EX2 filter fineness grade.
Suggested circuit layouts
A) The leakage oil of the hydrostatic drive is routed across the
filter.
B
A
P
1
Drain oil
to filter
Working hydraulics
The entire dirt produced in the hydrostatic drive by abrasion is
filtered out immediately and is thus not taken in by the pump of
the open-loop circuit.
This circuit layout is always recommended if the return flow only
slightly exceeds the suction flow, i.e. if there is a risk that the 0.5
bar / 7.3 psi pre-charge pressure cannot be maintained.
B) The drain oil of the hydrostatic drive is not routed across the
filter but is discharged directly into the tank.
B
A
P
1
Working hydraulics
Drain oil
to tank
This circuit layout has the advantage that drain oil pressures are
comparatively low.
Subject to change · 20.98-EN/US · 0818
Page 244
www.argo-hytos.com
Characteristics
Nominal flow rate
Up to 850 l/min / 224.6 gpm in return line
(see Selection Chart, column 2).
Up to 425 l/min / 112.3 gpm feed pump flow rate (see Layout)
The nominal flow rates indicated by ARGO-HYTOS are based on
the following features:
› closed by-pass valve at ν ≤ 200 mm
2
/s / 927 SUS
› element service life > 1000 operating hours at an average
fluid contamination of 0.07 g per l/min / 0.27 g per gpm
flow volume
› flow velocity in the return lines ≤ 4.5 m/s / 14.8 ft/s
› flow velocity in the suction lines ≤ 1.5 m/s / 4.9 ft/s
Connection
Threaded ports according to
› ISO 228 or DIN 13
› SAE standard J514
› SAE flange (3.000 psi)
Sizes see Selection Chart, column 6
(other port threads on request).
Please consider the connection size regarding max. flow
volumes.
Filter fineness
10 µm(c) ... 16 µm(c)
β-values according to ISO 16889
(see Selection Chart, column 4 and diagram Dx).
Dirt-holding capacity
Values in g test dust ISO MTD according to ISO 16889
(see Selection Chart, column 5).
Hydraulic fluids
Mineral oil and biodegradable fluids
(HEES and HETG, see info sheet 00.20).
Temperature range
-30 °C ... +100 °C (temporary -40 °C ... +120 °C)
-22 °F ... +212 °F (temporary -40 °F ... +248 °F)
Viscosity at nominal flow rate
› at operating temperature: ν < 60 mm
2
/s
› as starting viscosity: ν
max
= 1200 mm
2
/s
› at initial operation:
The recommended starting viscosity can be read from the
diagram D (pressure drop as a function of the kinematic
viscosity) as follows: Find the 70% ∆p of the cracking pressure
of the by-pass valve on the vertical axis. Draw a horizontal line
so that it intersects the ∆p curve at a point. Read this point on
the horizontal axis for the viscosity.
Operating pressure
Max. 10 bar / 145 psi
Materials
Screw-on cap: Aluminum alloy
Filter head: Aluminum alloy
Filter bowl: Steel
Seals: NBR (FPM on request)
Filter media: EXAPOR
®
MAX 2 – inorganic multi-layer
microfiber web
Fitting position
Up to 15° from the vertical, preferably vertical.
Even under unfavorable operating conditions (min. oil level, max.
sloping) the oil outlet resp. emergency suction has to be below
the oil level.
Subject to change · 20.98-EN/US · 0818
Page 245
www.argo-hytos.com
Diagrams
∆p-curves for complete filters in Selection Chart, column 3
(50 % of the nominal flow volume via connection B)
Filter fineness curves in Selection Chart, column 4
Dx
Filtration ratio β as a function of particle size x obtained
by the Multi-Pass-Test according to ISO 16889
The abbreviations represent the following β-values resp.
finenesses:
For EXAPOR
®
MAX 2 and Paper elements:
5EX2 =
β
5 (c)
= 200 EXAPOR
®
MAX 2
7EX2 = β
7 (c)
= 200 EXAPOR
®
MAX 2
10EX2 = β
10 (c)
= 200 EXAPOR
®
MAX 2
16EX2 = β
16 (c)
= 200 EXAPOR
®
MAX 2
30P = β
30 (c)
= 200 Paper
Based on the structure of the filter media of the 30P paper
elements, deviations from the printed curves are quite probable.
For special applications, finenesses differing from these curves
are also available by using special composed filter material.
Filtration ratio β for particles > x µm
Particle size x [µm] (for particles larger
than the given particle size x)
Efficiency [%]
0
1,0
0,5
1,5
2,0
E 598
1
0
2
400
200
600
800
1000
0
1,0
0,5
1,5
2,0
E 998
1
0
2
400
200
600
800
1000
D1
Pressure drop as a function of the flow volume
at ν = 35 mm
2
/s / 162 SUS (0 = casing empty)
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
1
2
3
4
5
200 400 600
800
1000
2
1
1+2
D2
Pressure drop as a function of the flow volume
at ν = 35 mm
2
/s / 162 SUS (0 = casing empty)
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
1
2
3
4
5
200 400 600
800
1000
2
1
1+2
ν [mm
2
/s]
ν [SUS]
Q [l/min]
∆p [bar]
∆p [psi]
∆p [bar]
∆p [psi]
Q [gpm]
ν [mm
2
/s]
ν [SUS]
Q [l/min]
∆p [bar]
∆p [psi]
∆p [bar]
∆p [psi]
Q [gpm]
Subject to change · 20.98-EN/US · 0818
0 52.8
105.7 158.5 211.3 264.2
72.5
58.0
43.5
29.0
14.5
0 927 1854 2781 3708 4635
29.0
21.8
14.5
7.3
2.0
1.5
1.0
0.5
0 52.8 105.7 158.5 211.3 264.2
72.5
58.0
43.5
29.0
14.5
0 927 1854 2781 3708 4635
29.0
21.8
14.5
7.3
2.0
1.5
1.0
0.5
Page 246
www.argo-hytos.com
Selection Chart
All filters are delivered with plugged clogging indicator connections M12 x 1.5.
As clogging indicators on the return side (P
1
) either manometers or electrical pressure switches can be used.
The monitoring of the vacuum on the suction side (P
2
) is additionally possible.
Order example: The filter E 598-256 has to be supplied with 5 + 5 connections (A
1
... A
5
, B
1
... B
5
).
Order description: E 598-556
Connections:
2 various options are available:
Option A
1
A
2
A
3
A
4
A
5
B
1
B
2
B
3
B
4
B
5
2 + 5 connections SAE 2½ G1
6
- - - G1¼ / SAE 1½ G1 G¾ G1½ / SAE 2 2
5 + 5 connections G1¼ / SAE 1½ G1 G¾ G1½ / SAE 2 G1¼ / SAE 1½ G1 G¾ G1½ / SAE 2 5
For the appropriate clogging indicator see catalog sheet 60.20.
Remarks:
› The start of the red area of the manometer respectively the switching pressure of the electrical pressure switch has always to be
lower than the cracking pressure of the pressure relief valve (see Selection Chart, column 8).
› Clogging indicators are optional and always delivered detached from the filter.
› The filters listed in this chart are standard filters. If modifications are required, we kindly ask for your request.
› For de-aeration a bleed valve (for connection P
1
) with Part No. SV 0112.15 is available.
l/min g bar bar kg
1 2 3 4 5 6 7 8 9 10 11 12 13
E 598-256 470 D1/1 10EX2 170 2 + 5 connections 0.5 2.5 1 • V7.1440-06 11.5
4+5
E 598-257 630 D1/2 16EX2 180 2 + 5 connections 0.5 2.5 1 • V7.1440-07 11.5
4+5
E 998-256 680 D2/1 10EX2 270 2 + 5 connections 0.5 2.5 1 • V7.1460-06 13.8
4+5
E 998-257 850 D2/2 16EX2 280 2 + 5 connections 0.5 2.5 1 • V7.1460-07 13.8
4+5
Part No.
Nominal return flow rate
1
Pressure drop see
diagram D/curve no.
Filter fineness see Diagr. Dx
Dirt-holding capacity
Connections
SAE (3000 psi)
Cracking pressure of CV
2
Cracking pressure of PRV
3
Symbol
Suction valve
Replacement filter element
Part No.
Weight
Remarks
1
The individual flow rates must be matched to the connections
2
Cracking pressure of check valve
3
Cracking pressure of pressure relief valve
4
With hole Ø 8 mm / 0.32 inch in the check valve for oil drain when opening the filter cover
5
With emergency-suction valve and protection strainer (mesh size 200 µm)
6
Connection G1 (A
2
) with locking screw
Subject to change · 20.98-EN/US · 0818
Page 247
www.argo-hytos.com
Selection Chart
All filters are delivered with plugged clogging indicator connections M12 x 1.5 mm.
As clogging indicators on the return side (P
1
) either manometers or electrical pressure switches can be used.
The monitoring of the vacuum on the suction side (P
2
) is additionally possible.
Order example: The filter E 598-756 has to be supplied with 5 + 5 connections (A
1
... A
5
, B
1
... B
5
).
Order description: E 598-856
Connections:
2 various options are available:
Option A
1
A
2
A
3
A
4
A
5
B
1
B
2
B
3
B
4
B
5
2 + 5 connections
SAE 2½ -16SAE
6
- - - -20SAE
7
/ SAE 1½ -16 SAE
6
-12 SAE
8
-24 SAE
9
/SAE 2 7
5 + 5 connections
- 20SAE
7
/ SAE 1½ -16 SAE
6
-12 SAE
8
-24 SAE
9
/ SAE 2 -20SAE
7
/ SAE 1½ -16 SAE
6
-12 SAE
8
-24 SAE
9
/SAE 2 8
For the appropriate clogging indicator see catalog sheet 60.20.
Remarks:
› The start of the red area of the manometer respectively the switching pressure of the electrical pressure switch has always to be
lower than the cracking pressure of the pressure relief valve (see Selection Chart, column 8).
› Clogging indicators are optional and always delivered detached from the filter.
› The filters listed in this chart are standard filters. If modifications are required, we kindly ask for your request.
› For de-aeration a bleed valve (for connection P
1
) with Part No. SV 0112.15 is available.
gpm g psi psi lbs
1 2 3 4 5 6 7 8 9 10 11 12 13
E 598-756 124.2 D1/1 10EX2 170 2 + 5 connections 7.3 36 1 • V7.1440-06 25.4
4+5
E 598-757 166.4 D1/2 16EX2 180 2 + 5 connections 7.3 36 1 • V7.1440-07 25.4
4+5
E 998-756 179.6 D2/1 10EX2 270 2 + 5 connections 7.3 36 1 • V7.1460-06 30.4
4+5
E 998-757 224.6 D2/2 16EX2 280 2 + 5 connections 7.3 36 1 • V7.1460-07 30.4
4+5
Part No.
Nominal return flow rate
1
Pressure drop see
diagram D/curve no.
Filter fineness see Diagr. Dx
Dirt-holding capacity
Connections
SAE (3000 psi)
Cracking pressure of CV
2
Cracking pressure of PRV
3
Symbol
Suction valve
Replacement filter element
Part No.
Weight
Remarks
1
The individual flow rates must be matched to the connections
2
Cracking pressure of check valve
3
Cracking pressure of pressure relief valve
4
With hole Ø 0.32 inch / 8 mm in the check valve for oil drain when opening the filter cover
5
With emergency-suction valve and protection strainer (mesh size 200 µm)
6
Connection -16 SAE (A
2
) with locking screw
7
Corresponds to 1
5
/
8
-12 UN-2B
8
Corresponds to 1
1
/
16
-12 UN-2B
9
Corresponds to 1
7
/
8
-12 UN-2B
Subject to change · 20.98-EN/US · 0818
Page 248
www.argo-hytos.com
Dimensions
Measurements in mm
Measurements in inch
Type A B C D E F
1
* F
2
* F
3
* F
4
* G H
1
H
2
I
E 598 s. Selection s. Selection 7.09 5.98 7.05 2.17 5.57 1.63 5.49 0.45 8.50 8.43 25.98
E 998 Chart Chart 7.09 5.98 7.05 2.17 5.57 1.63 5.49 0.45 8.50 8.43 33.86
Type K L M N O Q R S T
U
mm
V W X
E 598 15.98 8.66 4.17 4.92 M10 0.79 M12 2.76 7.87 AF 17 0.47 4.09 4.53
E 998 24.09 8.66 4.17 4.92 M10 0.79 M12 2.76 7.87 AF 17 0.47 4.09 4.53
* For use of SAE-flanges see this measurement
Type A B C D E F
1
* F
2
* F
3
* F
4
* G H
1
H
2
I
E 598 s. Selection s. Selection 180 152 179 55 141.5 41.5 139.5 11.5 216 214 660
E 998 Chart Chart 180 152 179 55 141.5 41.5 139.5 11.5 216 214 860
Type K L M N O Q R S T U V W X
E 598 406 220 106 125 M10 20 M12 70 200 AF 17 12 104 115
E 998 612 220 106 125 M10 20 M12 70 200 AF 17 12 104 115
B
5
R
B
5
B
2
A
2
H
2
F
4
F
3
V
A
3
/A
4
G
ØE
K
ØC
ØD
B
2
B
5
S
U
H
1
I
I
F
1
F
2
A
2
V
G
R
ØE
ØC
ØD
K
2xM
L
T
C
O
A
2
A
1
B
5
B
2
B
1
B
3
B
4
P
2
P
2
M
M
X
N
Q
L
B
3
B
4
P
2
P
2
B
1
A
1
P
1
P
1
A
2
B
5
B
2
A
4
A
3
A
5
M
W
90°
Version with 5 + 5 connections
Version with 2 + 5 connections
When using SAE-flanges
consider sizes F
1
... F
4
Connection G1 plugged
with locking screw
Dia hole in
reservoir
Connections M12 x 1.5
for clogging indicator
standard (mounting holes
for different pressure
switches on request)
Port sizes and mounting surface
(O-ring area of support hatched)
Tank surface sealing with
O-ring N007.1806
(included in basic equipment)
Subject to change · 20.98-EN/US · 0818
Page 249
www.argo-hytos.com
Spare Parts
3
2
1
2
Pos. Designation Part No.
1 Cover assy E 998.1200
2 O-ring
180 x 6 mm
7.09 x 0.24 inch
N007.1806
3 Replacement filter element see Chart. / col. 11
The functions of the complete filters as well as the outstanding
features of the filter elements assured by ARGO-HYTOS can only
be guaranteed if original ARGO-HYTOS spare parts are used.
Quality Assurance
Quality management according to DIN EN ISO 9001
To ensure constant quality in production and operation, ARGO-HYTOS filter elements undergo strict controls and tests according to
the following ISO standards:
ISO 2941 Verification of collapse / burst pressure rating
ISO 2942 Verification of fabrication integrity (Bubble Point Test)
ISO 2943 Verification of material compatibility with fluids
ISO 3968 Evaluation of pressure drop versus flow characteristics
ISO 16889 Multi-Pass-Test (evaluation of filter fineness and dirt-holding capacity)
ISO 23181 Determination of resistance to flow fatigue using high viscosity fluid
Various quality controls during the production process guarantee the leakfree function and solidity of our filters.
Illustrations may sometimes differ from the original. ARGO-HYTOS is not responsible for any unintentional mistake in this specification sheet.
Symbols
1
2
...
...
A
1
A
5
P
1
P
1
P
2
P
2
B
1
B
5
...
A
1
A
2
P
1
P
2
P
2
B
1
B
2
Subject to change · 20.98-EN/US · 0818