Subject to change · 20.20-e · 0215
Page 1
www.argo-hytos.com
E 043 · E 072
Tank top mounting · Connection up to G¾ · Nominal flow rate up to 70 l/min
Return Filters
Description
Application
In the return line circuits of hydraulic systems.
Performance features
Protection against wear:
By means of filter elements that, in full-flow filtration, meet even
the highest demands regarding cleanliness classes.
Protection against malfunction:
By means of full-flow filtration in the system return, the pumps
above all are protected from dirt particles remaining in the
system after assembly, repairs, or which are generated by wear
or enter the system from outside.
Special features
› By-pass valve:
The location close to the inlet port prevents dirt particles
retained by the filter element from entering into the clean oil
side.
› Removable bowl:
In case of maintenance the filter bowl is removed together
with the filter element – there fore dirt particles are not
flushed back into the tank.
› Extension pipe:
A correct extension pipe length ensures oil outlet below
minimum oil level and prevents foaming.
Filter elements
Flow direction from outside to centre. The star-shaped pleating
of the filter material results in:
› large filter surfaces
› low pressure drop
› high dirt-holding capacities
› long service life
Ventilating filter
Ventilation of the reservoir by an integral star-shape pleated filter
element:
› removable (replace annually!)
› splash-proof
› fineness 2 µm
Filter maintenance
By using a clogging indicator the correct moment for main-
tenance is stated and guarantees the optimum utilization of the
filter life.
Return Filter E 072
Page 2
www.argo-hytos.com
Subject to change · 20.20-e · 0215
Minerials
Screw-on cap: Polyester, GF-reinforced
Filter head: Aluminium alloy
Filter bowl: Polyamid, CF-reinforced, electrically
conducting
Seals: NBR (FPM on request)
Filter media: EXAPOR
®
MAX 2- organic multi-layer
microfibre web
Paper - cellulose web, impregnated with resin
Characteristics
Nominal flow rate
Up to 70 l/min (see Selection Chart, column 2)
The nominal flow rates indicated by ARGO-HYTOS are based on
the following features:
› closed by-pass valve at ν ≤ 200 mm
2
/s
› element service life > 1000 operating hours at an average
› fluid contamination of 0,07 g per l/min flow volume
› flow velocity in the connection lines ≤ 4,5 m/s
Connection
Threaded ports according to ISO 228 or DIN 13.
Sizes see Selection Chart, column 6 (other port threads on
request)
Filter fineness
5 µm(c) ... 30 µm(c)
β-values according to ISO 16889
(see Selection Chart, column 4 and diagram Dx)
Dirt-holding capacity
Values in g test dust ISO MTD according to ISO 16889
(see Selection Chart, column 5)
Hydraulic fluids
Mineral oil and biodegradable fluids
(HEES and HETG, see info-sheet 00.20).
With high filling conditions we recommend an electrical
conductivity >_ 500 pS/m at 20 °C.
Temperature range
-30 °C ... +100 °C (temporary -40 °C ... +120 °C)
Viscosity at nominal flow rate
› at operating temperature: ν < 60 mm
2
/s
› as starting viscosity: ν
max
= 1200 mm
2
/s
› at initial operation:
The recommended starting viscosity can be read from the
diagram D (pressure drop as a function of the kinematic
viscosity) as follows: Find the 70 % ∆p of the cracking pressure
of the by-pass valve on the vertical axis. Draw a horizontal line
so that it inter-sects the ∆p curve at a point. Read this point on
the horizontal axis for the viscosity.
Operating pressure
Max. 10 bar
Mounting position
Preferably vertical, outlet downwards
Accessories
Electrical and optical clogging indicators are available on request.
Dimensions and technical data see catalogue sheet 60.20.
An optional oil separator (Part No. E 043.1701) is available on
request.
Extension pipes on the bowl outlet are available in several
lengths on request.
A self-assembly system for installation of extension pipes can be
ordered. For detailed information please see catalogue sheet
20.390.
Page 3
www.argo-hytos.com
Subject to change · 20.20-e · 0215
Diagrams
∆p-curves for complete filters in Selection Chart, column 3
D1
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
0,2
0,4
0,6
0,8
1
1
2
0
3
10
15
25
35
5
20 30
40
E 043
0
1
2
3
4
5
1
3
2
200 400 600
800
1000
∆p [bar]
∆p [bar]
Q [l/min]
ν [mm
2
/s]
D2
0
0,2
0,4
0,6
0,8
1
1
2
3
0
4
20
10
30
50
70
40 60
80
E 072
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
∆p [bar]
Q [l/min]
0
1
2
3
4
5
2
1
4
3
200 400 600
800
1000
Pressure drop as a function of the
kinematic viscosity at nominal flow
∆p [bar]
ν [mm
2
/s]
Filter fineness curves in Selection Chart, column 4
Dx
Filtration ratio β as a function of particle size x
obtained by the Multi-Pass-Test according to
ISO 16889
The abbreviations represent the following β-values resp.
finenesses:
For EXAPOR
®
MAX 2 and Paper elements:
5EX2 = β
5 (c)
= 200 EXAPOR
®
MAX 2
7EX2 = β
7 (c)
= 200 EXAPOR
®
MAX 2
10EX2 = β
10 (c)
= 200 EXAPOR
®
MAX 2
16EX2 = β
16 (c)
= 200 EXAPOR
®
MAX 2
30P = β
30 (c)
= 200 Paper
Based on the structure of the filter media of the 30P paper
elements, deviations from the printed curves are quite probable.
For screen elements:
40S = screen material with mesh size 40 µm
60S = screen material with mesh size 60 µm
100S = screen material with mesh size 100 µm
Tolerances for mesh size according to DIN 4189
For ventilating filter elements:
2CL = 99,5 % efficiency for particles of size 2 µm
For special applications, finenesses differing from these curves
are also available by using special composed filter material.
Filtration ratio β for particles > x µm
Particle size x [µm] (for particles larger
than the given particle size x)
Efficiency [%]
Page 4
www.argo-hytos.com
Subject to change · 20.20-e · 0215
Selection Chart
l/min g bar kg
1 2 3 4 5 6 7 8 9 10 11 12
E 043-156 25 D1/1 10EX2 6,1 G
1
/
2
2,5 2 V3.0510-56 0,6 L1.0403-01 (2CL) -
E 043-166 25 D1/1 10EX2 6,1 G
1
/
2
2,5 1 V3.0510-56 0,6 - -
E 043-158 35 D1/2 16EX2 6,1 G
1
/
2
2,5 2 V3.0510-58 0,6 L1.0403-01 (2CL) -
E 043-168 35 D1/2 16EX2 6,1 G
1
/
2
2,5 1 V3.0510-58 0,6 - -
E 043-151 30 D1/3 30P 4,0 G
1
/
2
1,5 2 P3.0510-51 0,6 L1.0403-01 (2CL) -
E 043-161 30 D1/3 30P 4,0 G
1
/
2
1,5 1 P3.0510-51 0,6 - -
E 072-153 25 D2/1 5EX2 7,7 G
3
/
4
2,5 2 V3.0520-53 0,8 L1.0403-01 (2CL) -
E 072-163 25 D2/1 5EX2 7,7 G
3
/
4
2,5 1 V3.0520-53 0,8 - -
E 072-156 50 D2/2 10EX2 13 G
3
/
4
2,5 2 V3.0520-56 0,8 L1.0403-01 (2CL) -
E 072-166 50 D2/2 10EX2 13 G
3
/
4
2,5 1 V3.0520-56 0,8 - -
E 072-158 70 D2/3 16EX2 13 G
3
/
4
2,5 2 V3.0520-58 0,8 L1.0403-01 (2CL) -
E 072-168 70 D2/3 16EX2 13 G
3
/
4
2,5 1 V3.0520-58 0,8 - -
E 072-151 50 D2/4 30P 6,6 G
3
/
4
1,5 2 P3.0520-51* 0,8 L1.0403-01 (2CL) -
E 072-161 50 D2/4 30P 6,6 G
3
/
4
1,5 1 P3.0520-51* 0,8 - -
Part No.
Nominal flow rate
Pressure drop see
diagram
D/
curve no.
Filter fineness see Diagr.
Dx
Dirt-holding capacity
Connection A
Cracking pressure of by-pass
Symbol
Replacement element
Part No.
Weight
Replacement ventilating filter
Part No.
(Filter fineness see diagrams)
Remarks
All filters are delivered with a plugged clogging indicator connection M12 x 1,5. As clogging indicators either manometers or
electrical pressure switches can be used. Optional extension pipes adapt the filter length to various tank depths. For ordering of
accessories please use the below mentioned codes.
Order example: The filter E 072-156 has to be supplied with an extension pipe for a mounting depth of 500 mm.
Order description: E 072-156 / EV 500
Part No. (Basic unit)
Mounted extension pipe (5 various lengths are available on request)
E 043: EV 150, EV 200, EV 300, EV 400, EV 500
E 072: EV 250, EV 300, EV 400, EV 500, EV 600
For the appropriate clogging indicators see catalogue sheet 60.20.
Remarks:
› The switching pressure of the electrical pressure switch has always to be lower than the cracking pressure of the by-pass valve
(see Selection Chart, column 7).
› Clogging indicators are optional and always delivered detached from the filter.
› The filters listed in this chart are standard filters. Other designs available on request.
* Paper media supported with metal gauze
Page 5
www.argo-hytos.com
Subject to change · 20.20-e · 0215
Dimensions
Measurements
Type A B C
min/max
D E F G H I1 I2 K L M N O P1 P2 Q R S
E 043 G1/2 75 60/63 51 27,8 24 26 67 175 110 83 88 9 51 11 59,5 57,5 46 79 42
E 072 G3/4 75 60/63 51 27,8 24 26 67 270 110 180 88 9 51 11 59,5 57,5 46 79 42
Type T U V W X
E 043 2 21 AF 21 35 AF 36
E 043 2 21 AF 21 35 AF 36
Symbols
1
2
Oil separator optional
ARGO-HYTOS
Part No. E 043.1701
Design with ventilating filter Design without ventilating filter
Max. oil level under
stationary conditions
when using an
oil separator
Flat gasket (included in
basic equipment)
Dia hole in reservoir
Extension pipe
on request
Required mounting surface
Ventilating filter
Fineness 2 µm
(replaceable)
Connection M12 x 1,5
for clogging indicator
B
E
Page 6
www.argo-hytos.com
Subject to change · 20.20-e · 0215
Spare Parts
9
10
1
2
3
4
5
6
7
8
Pos. Designation Part No.
1 Screw-on cap FR 043.0201
2 Compression spring N015.1606
3 O-ring 57 x 3 N007.0573
4 Filter element see Chart / col. 9
5 Filter bowl E 043 * FR 043.0107
5 Filter bowl E 072 * FR 072.0104
6 O-ring 50 x 2 N007.0501
7 Ventilating filter L1.0403-01
8 Flat gasket (for versions D 043.0113
without oil separator)
9 Oil separator with Pos. 10 E 043.1701
10 Flat gasket (for versions D 043.0118
with oil separator)
Quality Assurance
Quality management according to DIN EN ISO 9001
To ensure constant quality in production and operation, ARGO-HYTOS filter elements undergo strict controls and tests according to
the following ISO standards:
ISO 2941 Verification of collapse/burst pressure rating
ISO 2942 Verification of fabrication integrity (Bubble Point Test)
ISO 2943 Verification of material compatibility with fluids
ISO 3968 Evaluation of pressure drop versus flow characteristics
ISO 16889 Multi-Pass-Test (evaluation of filter fineness and dirt-holding capacity)
ISO 23181 Determination of resistance to flow fatigue using high viscosity fluid
Various quality controls during the production process guarantee the leakfree function and solidity of our filters.
Illustrations may sometimes differ from the original. ARGO-HYTOS is not responsible for any unintentional mistake in this specification sheet.
* Specify mounting depth (EV) in mm
The functions of the complete filters as well as the outstanding
features of the filter elements assured by ARGO-HYTOS can
only be guaranteed if original ARGO-HYTOS spare parts are
used.