Subject to change · 30.10-e · 0215
Page 1
www.argo-hytos.com
D 042 · D 062
In-line mounting · Operating pressure up to 100 bar · Nominal flow rate up to 90 l/min
Pressure Filters
Description
Application
In the pressure circuits of hydraulic and lubrication systems.
Performance features
Protection against wear:
By means of filter elements that, in full-flow filtration, meet even
the highest demands regarding cleanliness classes.
Protection against malfunction:
Through installation near to the control valves or other expensive
components. The specific determined flow rate guarantees a
closed by-pass valve even at ν ≤ 200 mm
2
/s (cold start conditi-
on).
Filter elements
Flow direction from outside to centre. The star-shaped pleating
of the filter material results in:
› large filter surfaces
› low pressure drop
› high dirt-holding capacities
› long service life
Filter maintenance
By using a clogging indicator the correct moment for main-
tenance is stated and guarantees the optimum utilization of the
filter life.
Materials
Filter head: Aluminium alloy
Filter bowl: Aluminium alloy
Seals: NBR (FPM on request)
Filter media: EXAPOR
®
MAX 2 - inorganic multi-layer
microfibre web
Paper - cellulose web, impregnated with resin
Accessories
Electrical and/or optical clogging indicators are available -
optionally with one or two switching points resp. temperature
suppression.
Dimensions and technical data see catalogue sheet 60.30.
Pressure Filter D 042
Page 2
www.argo-hytos.com
Subject to change · 30.10-e · 0215
Characteristics
Operating pressure
0 ... 63 bar, min. 3 x 10
6
pressure cycles
Nominal pressure according to DIN 24550
0 ... 100 bar, min. 10
4
pressure cycles
Quasi-static operating pressure
Permissible pressures for other numbers of cycles
100
75
50
0
0
10
3
10
4
10
5
10
6
10
7
10
8
Operating pressure p [bar]
Number of cycles n
Nominal flow rate
Up to 90 l/min (see Selection Chart, column 2)
The nominal flow rates indicated by ARGO-HYTOS are based on
the following features:
› closed by-pass valve at ν ≤ 200 mm
2
/s
› element service life > 1000 operating hours at an average
fluid
› contamination of 0,07 g per l/min flow volume
› flow velocity in the connection lines:
up to 100 bar ≤ 6 m/s
Filter fineness
5 µm(c) ... 30 µm(c)
β-values according to ISO 16889
(see Selection Chart, column 4 and diagram Dx)
Dirt-holding capacity
Values in g test dust ISO MTD according to ISO 16889
(see Selection Chart, column 5)
Hydraulic fluids
Mineral oil and biodegradable fluids
(HEES and HETG, see info-sheet 00.20)
Temperature range
-30 °C ... +100 °C (temporary -40 °C ... +120 °C)
Viscosity at nominal flow rate
› at operating temperature: ν < 60 mm
2
/s
› as starting viscosity: ν
max
= 1200 mm
2
/s
› at initial operation:
The recommended starting viscosity can be read from the
diagram D (pressure drop as a function of the kinematic
viscosity) as follows: Find the 70 % ∆p of the cracking
pressure of the by-pass valve on the vertical axis. Draw a
horizontal line so that it intersects the ∆p curve at a point.
Read this point on the horizontal axis for the viscosity.
Mounting position
Preferably vertical, filter head on top
Connection
Threaded ports according to ISO 228 or DIN 13.
Sizes see Selection Chart, column 6 (other port threads on
request).
Page 3
www.argo-hytos.com
Subject to change · 30.10-e · 0215
Diagrams
∆p-curves for complete filters in Selection Chart, column 3
D1
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
0
0,5
1,0
1,5
2,0
D 042
1+5
2+6
4
0
3
10 20 30 40 50
∆p [bar]
Q [l/min]
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
2
8
10
4
6
1
1
4
4
5
6
5+6
3
2
2
200 400 600
800
1000
∆p [bar]
ν [mm
2
/s]
D2
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
0
0,5
1,0
1,5
2,0
D 062
1+5
2+6
4
0
3
20 40 60 80
100
∆p [bar]
Q [l/min]
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
2
8
10
4
6
1
4
5
6
4
2
3
200 400 600
800
1000
∆p [bar]
ν [mm
2
/s]
Dx
Filter fineness curves in Selection Chart, column 4
Filtration ratio β as a function of particle size x obtained
by the Multi-Pass-Test according to ISO 16889
The abbreviations represent the following β-values resp.
finenesses:
For EXAPOR
®
MAX2 and Paper elements:
5EX2 = β
5 (c)
= 200 EXAPOR
®
MAX 2
7EX2 = β
7 (c)
= 200 EXAPOR
®
MAX 2
10EX2 = β
10 (c)
= 200 EXAPOR
®
MAX 2
16EX2 = β
16 (c)
= 200 EXAPOR
®
MAX 2
30P = β
30 (c)
= 200 Paper
Based on the structure of the filter media of the 30P paper
elements, deviations from the printed curves are quite probable.
For special applications, finenesses differing from these curves
are also available by using special composed filter media.
Filtration ratio β for particles > x µm
Particle size x [µm] (for particles larger
than the given particle size x)
Efficiency [%]
Page 4
www.argo-hytos.com
Subject to change · 30.10-e · 0215
Selection Chart
Optical or electrical indicators are available to monitor the clogging condition of the element. If the indicator should be already
mounted onto the filter head use the abbreviation “M” behind the part number of the indicator. The printed order acknowledge-
ments show both items separately.
Order example: The filter D 042-156 has to be supplied with optical clogging indicator - response pressure 2,0 bar
Order description: D 042-156 / DG 042-01 M
Part No. (Basic unit) Mounted
Clogging indicator
For the appropriate clogging indicators see catalogue sheet 60.30
Remarks:
› The switching pressure of the clogging indicator has always to be lower than the cracking pressure of the by-pass valve
(see Selection Chart, column 7).
› The filters listed in this chart are standard filters. Other designs available on request.
* Paper media supported with metal gauze
l/min g bar kg
1 2 3 4 5 6 7 8 9 10 11 12
D 042-153 16 D1/1 5EX2 4,9 G½ 3,5 4 V3.0510-03 0,8 optional -
D 042-156 27 D1/2 10EX2 6,8 G½ 3,5 4 V3.0510-06 0,8 optional -
D 042-158 44 D1/3 16EX2 6,9 G½ 3,5 4 V3.0510-08 0,8 optional -
D 042-151 40 D1/4 30P 3,6 G½ 3,5 4 P3.0510-11* 0,8 optional -
D 042-183 30 D1/5 5EX2 4,9 G½ 7 4 V3.0510-03 0,8 optional -
D 042-186 44 D1/6 10EX2 6,8 G½ 7 4 V3.0510-06 0,8 optional -
D 062-153 32 D2/1 5EX2 10 G½ 3,5 4 V3.0520-03 1,1 optional -
D 062-156 57 D2/2 10EX2 14 G¾ 3,5 4 V3.0520-06 1,1 optional -
D 062-158 90 D2/3 16EX2 15 G¾ 3,5 4 V3.0520-08 1,1 optional -
D 062-151 80 D2/4 30P 7,1 G¾ 3,5 4 P3.0520-01* 1,1 optional -
D 062-183 48 D2/5 5EX2 10 G½ 7 4 V3.0520-03 1,1 optional -
D 062-196 80 D2/6 10EX2 14 G¾ 7 4 V3.0520-06 1,1 optional -
Part No.
Nominal flow rate
Pressure drop see
diagram D
/curve no.
Filter fineness see diagr.
Dx
Dirt-holding capacity
Connection A/B
Cracking pressure of by-pass
Symbol
Replacement filter element
Part No.
Weight
Clogging indicator
Remarks
Page 5
www.argo-hytos.com
Subject to change · 30.10-e · 0215
Dimensions
G
B
A
E
F
D
K
ØC
ØC
ØH
U
S
T
ØR
V
W
L
P
O
N
M
Q
P
1
P
2
Clogging indicator optional:
Pressure holes plugged with screws M4
D
G
0
41
Minimum distance from
ferromagnetic parts: 7 mm
Measurements
Type A/B C D E F G H I K L M
Ø/depth
N O P Q R S T U V W
D 042 G½ 39 148 27 45,5 80 58,5 55 27 35 M6/8 44 AF 36 19 15 70 81 55 23 30 35,5
D 062 G½, G¾ 39 244 27 45,5 80 58,5 55 27 35 M6/8 44 AF36 19 15 70 81 55 23 30 35,5
Symbols
1 32 4 5
P
1
P
2
6 7
P
1
P
2
Page 6
www.argo-hytos.com
Subject to change · 30.10-e · 0215
Spare Parts
2
3
1
4
5
Pos. Designation Part No.
1 Filter bowl D 042 D 044.0101
1 Filter bowl D 062 D 064.0101
2 O-ring 50 x 2 N007.0501
3 Filter element (with seal) s. Chart / col. 9
4 Hexagonal head screw M4 x 8
DIN 933-8.8
11385800
5 Bonded Seal 4,1 x 7,2 x 1 12504600
The functions of the complete filters as well as the outstanding
features of the filter elements assured by ARGO-HYTOS can
only be guaranteed if original ARGO-HYTOS spare parts are
used.
Quality Assurance
Quality management according to DIN EN ISO 9001
To ensure constant quality in production and operation, ARGO-HYTOS filter elements undergo strict controls and tests according to
the following ISO standards:
ISO 2941 Verification of collapse/burst pressure rating
ISO 2942 Verification of fabrication integrity (Bubble Point Test)
ISO 2943 Verification of material compatibility with fluids
ISO 3968 Evaluation of pressure drop versus flow characteristics
ISO 16889 Multi-Pass-Test (evaluation of filter fineness and dirt-holding capacity)
ISO 23181 Determination of resistance to flow fatigue using high viscosity fluid
Before release into the series production the filter casing is tested for fatigue strength in our pressure pulse test rig.
Various quality controls during the production process guarantee the leakfree function and solidity of our filters.
Illustrations may sometimes differ from the original. ARGO-HYTOS is not responsible for any unintentional mistake in this specification sheet.