Subject to change 20.50-e · 0215
Page 1
www.argo-hytos.com
E 444 · E 454 · E 464 · E 644
Tank top mounting · Connection up to SAE 2 · Nominal fl ow rate up to 680 l/min
Return Filters
Description
Application
In the return line circuits of hydraulic systems.
Performance features
Protection against wear:
By means of fi lter elements that, in full-fl ow fi ltration, meet even
the highest demands regarding cleanliness classes.
Protection against malfunction:
By means of full-fl ow fi ltration in the system return, the pumps
above all are protected from dirt particles remaining in the
system after assembly, repairs, or which are generated by wear
or enter the system from outside.
Special features
› By-pass valve:
The location close to the inlet port prevents dirt particles
retained by the fi lter element from entering into the clean oil
side.
› Removable bowl:
In case of maintenance the fi lter bowl is removed together
with the fi lter element - therefore dirt particles are not fl ushed
back into the tank.
Filter elements
Flow direction from outside to centre. The star-shaped pleating
of the fi lter material results in:
› large fi lter surfaces
› low pressure drop
› high dirt-holding capacities
› long service life
In fi lters with a magnetic system, the ferromagnetic particles in
the fl uid pass fi rst through a strong magnetic fi eld and are
separated.
Filter maintenance
By using a clogging indicator the correct moment for main-
tenance is stated and guarantees the optimum utilization of the
fi lter life.
Materials
Filter head cover: Aluminium alloy
Filter head: Aluminium alloy
Housing: Steel, phosphated
Housing bottom: Polyamide, GF reinforced
Seals: NBR (FPM om request)
Filter media: EXAPOR
®
MAX 2 - inorganic multi-layer
microfi bre web
Paper - cellulose web, impregnated with
resin, stainless steel wire mesh (1.4301)
Return Filter E 454
Return Filter E 454
Page 2
www.argo-hytos.com
Subject to change · 20.50-e · 0215
Accessories
Extension pipes or diffusers on the bowl outlet are available on
request. Even the combination of both options is possible.
› Extension pipe:
A correct extension pipe length ensures oil outlet below
minimum oil level and prevents foaming.
› Diffuser:
Diffusers reduce oil velocity and direct the oil to 90° outlet
flow. This function prevents also oil foaming and whirling up
of solid particles settled at the tank bottom. The mesh screen
element filters the oil in case of an open by-pass valve.
Electrical and optical clogging indicators are available on request.
Dimensions and technical data see catalogue sheet 60.20.
Characteristics
Nominal flow rate
Up to 680 l/min (see Selection Chart, column 2). The nominal
flow rates indicated by ARGO-HYTOS are based on the
following features:
› closed by-pass valve at ν ≤ 200 mm
2
/s
› element service life > 1000 operating hours at an average
fluid contamination of 0,07 g per l/min flow volume
› flow velocity in the connection lines ≤ 4,5 m/s
Connection
Threaded ports according to ISO 228 or DIN 13 and SAE-flange
(3000 psi). Sizes see Selection Chart, column 6 (other port
threads on request).
Filter fineness
5 µm(c) ... 60 µm(c)
β-values according to ISO 16889
(see Selection Chart, column 4 and diagram Dx)
Dirt-holding capacity
Values in g test dust ISO MTD according to ISO 16889
(see Selection Chart, column 5)
Hydraulic fluids
Mineral oil and biodegradable fluids
(HEES and HETG, see info-sheet 00.20).
Temperature range
-30 °C ... +100 °C (temporary -40 °C ... +120 °C)
Viscosity at nominal flow rate
› at operating temperature: ν < 60 mm
2
/s
› as starting viscosity: ν
max
= 1200 mm
2
/s
› at initial operation:
The recommended starting viscosity can be read from the
diagram D (pressure drop as a function of the kinematic
viscosity) as follows: Find the 70 % ∆p of the cracking
pressure of the by-pass valve on the vertical axis. Draw a
horizontal line so that it intersects the ∆p curve at a point.
Read this point on the horizontal axis for the viscosity.
Operating pressure
Max. 10 bar
Mounting position
Preferably vertical, outlet downwards
Page 3
www.argo-hytos.com
Subject to change · 20.50-e · 0215
Diagrams
∆p-curves for complete filters in Selection Chart, column 3
D1
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
1
2
0
3+4
100
200
300
400
500
600
700
E 444
0
1
2
3
4
4
2
3
1
200 400 600
800
1000
Q [l/min]
ν [mm
2
/s]
D2
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
1
2
3+4
100
200
300
400
500
600
700
E 454
5
0
Q [l/min]
0
1
2
3
4
4
2
3
1
200 400 600
800
1000
ν [mm
2
/s]
D3
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
1
2
0
3+4
100
200
300
400
500
600
700
E 464
Q [l/min]
0
1
2
3
4
4
2
3
1
200 400 600
800
1000
ν [mm
2
/s]
D4
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
1
0
100
200
300
400
500
600
700
E 644
Q [l/min]
0
1
2
5
3
4
1
200 400 600
800
1000
ν [mm
2
/s]
∆p [bar]
∆p [bar]
∆p [bar]
∆p [bar]
∆p [bar]
∆p [bar]
∆p [bar]
∆p [bar]
Page 4
www.argo-hytos.com
Subject to change · 20.50-e · 0215
Filtration ratio β as a function of particle size x obtained
by the Multi-Pass-Test according to ISO 16889
The abbreviations represent the following β-values resp.
finenesses:
For EXAPOR
®
MAX 2 and Paper elements:
5EX2 =
β
5 (c)
= 200 EXAPOR
®
MAX 2
7EX2 = β
7 (c)
= 200 EXAPOR
®
MAX 2
10EX2 = β
10 (c)
= 200 EXAPOR
®
MAX 2
16EX2 = β
16 (c)
= 200 EXAPOR
®
MAX 2
30P = β
30 (c)
= 200 Paper
Based on the structure of the filter media of the 30P paper
elements, deviations from the printed curves are quite probable.
Screen elements:
40S = screen material with mesh size 40 µm
60S = screen material with mesh size 60 µm
100S = screen material with mesh size 100 µm
Tolerances for mesh size according to DIN 4189
For special applications, finenesses differing from these curves
are also available by using special composed filter media.
Filter fineness curves in Selection Chart, column 4
Dx
All filters are delivered with a plugged clogging indicator connection M12 x 1,5. (Mounting holes for differential pressure switches
on request). As clogging indicators either manometers or electrical pressure switches can be used. Two different head pieces with
three various connecting options are available. All filters can also be supplied with an outlet diffuser. Optional extension pipes
adapt the filter length to various tank depths. For ordering of accessories please use the below mentioned codes.
Order example: The filter E 453-456 has to be supplied with 2 connections (A and A3), an outlet diffuser and an
extension pipe for 564 mm length.
Order description: E 454- 256 / VD / EV 564
Connections:
3 various options are available
one connection (A) - G1½ / SAE 2 1
two connections
1
(A und A3) - G1½ / SAE 2 und G¾ 2
four connections
1
(A1, A2, A3 und A4) - 2 x G1¼ / SAE 1½, G¾ und G1 4
Options (bowl outlet):
2 various options are available
VD: Outlet diffuser, RV: Extension pipe
Extension pipe:
7 various lengths are available
EV = K (Bowl length) + 81 / + 136 / + 196 / + 231 / + 356 / + 446 / + 626 mm (see section dimensions and measurements)
For the appropriate clogging indicators see catalogue sheet 60.20.
Remarks:
› The switching pressure of the electrical pressure switch has always to be lower than the cracking pressure of the by-pass valve
(see Selection Chart, column 7).
› Clogging indicators are optional and always delivered detached from the filter.
› The filters listed in this chart are standard filters. Other designs, e.g. with screen elements (mesh size 450 µm) at the bowl
outlet, are available on request.
Filtration ratio β for particles > x µm
Particle size x [µm] (for particles larger
than the given particle size x)
Efficiency [%]
1
The individual flow rates must match the connections
Order Information
Page 5
www.argo-hytos.com
Subject to change · 20.50-e · 0215
Selection Chart
l/min g bar kg
1 2 3 4 5 6 7 8 9 10 11
E 444-459 115 D1/1 5EX2 45 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1217-53 4,4 -
E 444-456 200 D1/2 10EX2 61 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1217-56 4,4 -
E 444-468 270 D1/3 16EX2 62 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1217-58 4,4 -
E 444-481 175 D1/4 30P 29 2 x G1¼ / SAE1½, G¾ + G1 1,5 3 P2.1217-51
2
4,4 -
E 454-459 220 D2/1 5EX2 93 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1234-23 6,1 -
E 454-456 375 D2/2 10EX2 130 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1234-26 6,1 -
E 454-468 480 D2/3 16EX2 124 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1234-28 6,1 -
E 454-453 350 D2/4 30P 63 2 x G1¼ / SAE1½, G¾ + G1 1,5 3 P2.1234-41
2
6,1 -
E 454-400 525 D2/5 60S (3600 cm²) 2 x G1¼ / SAE1½, G¾ + G1 1,5 6 S2.1234-00 6,4 with magnetic
system
E 464-459 300 D3/1 5EX2 140 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1250-03 7,8 -
E 464-456 500 D3/2 10EX2 200 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1250-06 7,8 -
E 464-468 600 D3/3 16EX2 200 2 x G1¼ / SAE1½, G¾ + G1 2,5 3 V2.1250-08 7,8 -
E 464-453 480 D3/4 30P 95 2 x G1¼ / SAE1½, G¾ + G1 1,5 3 P2.1250-11
2
7,8 -
E 644-476 680 D4/1 10EX2 250 2 x G1¼ / SAE1½, G¾ + G1 3,0 3 V2.1260-46 9,5
Part No.
Nominal flow rate
1
Pressure drop see
diagram D/curve no.
Filter fineness see Diagr. Dx
Dirt-holding capacity
Filter surface in ( )
Connection A
SAE (3000 psi)
Cracking pressure of by-pass
Symbol
Replacement filter element
Part No.
Weight
Remarks
2
Paper media supported with metal gauze
Page 6
www.argo-hytos.com
Subject to change · 20.50-e · 0215
Dimensions
H
K
F
B
G
I+(ET-K)
minimum distance
for filter maintenance
M12
EØ
DØ
CØ
Dia hole in
reservoir
Versions with 1 or 2 connections
Option VD EV
Option VD
EV
T1
ET
Version with 4 connections
Z
H
B
Tank surface sealing either with
flat gasket E 442.0103
or O-ring N007.1375
(both items included in basic equipment)
S
S
M
Q
N
(optional)
W
V
X
Y
P
P
Connection M12 x 1,5 for
clogging indicators standard
(mounting holes for differential
pressure switches on request)
P
15
A
M10
90°
4 x 90°
Ø 185
T2
O
O
P
Ø 140,5
▫
2xM
11,5Ø
For calculation of dimension EV see Selection Chart
Measurements
* for design with 4 connections
Symbole
1 2 3 4 5 6
Type A B C D E F G H I K M N O Q S T1 T2 V W X Y Z
E 444
see
2 141 128,5 139,9 12 36/35* 90 315 195 86,5 116 35 18 92 47,5 64 98,5 110,5 89 98,5 32,5
E 454
Selection
2 141 128,5 139,9 12 36/35* 90 485 362 86,5 116 35 18 92 47,5 64 98,5 110,5 89 98,5 32,5
E 464
Chart
2 141 128,5 139,9 12 36/35* 90 650 530 86,5 116 35 18 92 47,5 64 98,5 110,5 89 98,5 32,5
E 644 2 141 128,5 139,9 12 36/35* 90 750 630 86,5 116 35 18 92 47,5 64 98,5 110,5 89 98,5 32,5
Page 7
www.argo-hytos.com
Subject to change · 20.50-e · 0215
Spare Parts
Pos. Designation Part No.
1 Cover E 443.1200
1a Cover
with magnetic system
E 443.1210
2 Hexagonscrew M10 x 35 28213600
3 By-pass (1,5 bar) E 440.1500
3 By-pass (2,5 bar) E 460.1520
3 By-pass (3,0 bar) E 640.1510
4 Filter elements s. Chart / col. 9
5 Filter bowl E 444 * E 441.1900
5 Filter bowl E 454 * E 451.1900
5 Filter bowl E 464 * E 461.1900
5 Filter bowl E 644 * E 641.1900
6 O-ring 125 x 6 N007.1256
7 O-ring 151,76 x 5,33 N007.1525
8 Flat gasket E 442.0103
9 O-ring 136.5 x 5,34 N007.1375
* Please indicate options (VD, VDEV, resp. RVEV)
The functions of the complete filters as well as the outstanding
features of the filter elements assured by ARGO-HYTOS can only
be guaranteed if original ARGO-HYTOS spare parts are used.
Quality Assurance
Quality management according to DIN EN ISO 9001
To ensure constant quality in production and operation, ARGO-HYTOS filter elements undergo strict controls and tests according to
the following ISO standards:
ISO 2941 Verification of collapse/burst pressure rating
ISO 2942 Verification of fabrication integrity (Bubble Point Test)
ISO 2943 Verification of material compatibility with fluids
ISO 3968 Evaluation of pressure drop versus flow characteristics
ISO 16889 Multi-Pass-Test (evaluation of filter fineness and dirt-holding capacity)
ISO 23181 Determination of resistance to flow fatigue using high viscosity fluid
Various quality controls during the production process guarantee the leakfree function and solidity of our filters.
Illustrations may sometimes differ from the original. ARGO-HYTOS is not responsible for any unintentional mistake in this specification sheet.
1
1a
3
4
5
6
7
8
9
2