FS330
LIQZP-LEB, LIQZP-LES
Digital high performance 2-way proportional
cartridges specifically designed for high
speed closed loop controls.
They are
equipped with two LVDT position transducers
for best dynamics in not compensated flow
regulations. The cartridge execution for
blocks installation grants high flow capabili-
ties and minimized pressure drops.
LEB basic execution with analog reference
signal or IO-Link interface for digital reference
signals, valve settings, and real-time diagnostics.
LES full execution which includes also
optional fieldbus interfaces for digital
reference signals, valve settings, and real-
time diagnostics.
Bluetooth/USB connection is always present
for valve settings via mobile App and Atos PC
software.
Size: 16 ÷ 125 - ISO 7368
Max flow:
600 ÷
22000 l/min
Max pressure: 420 bar
Valve size ISO 7368, see section
:
Size 16 25 32 40
l/min 250 500 800 1200
Size 50 63 80 100 125
l/min 2000 3000 4500 7200 9350
Nominal flow (l/min) at Δp 5 bar
10
Digital proportional 2-way cartridges high performance
piloted, with on-board driver and two LVDT transducers
1
MODEL CODE
a
b
c
d
e
f
g
h
i
j
k
l
Poppet
Sleeve
Main stage LVDT transducer
Pilot valve
On-board digital driver
Bluetooth/USB connection
Fieldbus connectors
Main connector
Pilot valve LVDT transducer
Air bleeding
Air suction port
X1 port (external pilot pressure)
X
Y
B
A
functional symbol
LIQZP
Proportional 2-way
cartridge, piloted
/
25 2 L4
*
Poppet type, regulating characteristics, see section
:
13
L4 = linear
Configuration:
2 = 2 way
----
LES NPSN
Alternated p/Q controls:
SN = none
LIQZP-LES-SN-BP-322L4
simplified symbol
(1) Possible combined options: /FI, /IQ, /IZ (/T Bluetooth adapter option and /V damping plate option can be combined with all other options)
Electronic options (1), not available for LEB-SN-IL:
F = fault signal
I = current reference input and monitor 4 ÷ 20 mA
Q
= enable signal
Z = double power supply (only for LES), enable, fault and
monitor signals - 12 pin connector
Fieldbus interfaces, only for LES, see section
:
NP = Not present
BC = CANopen EW = POWERLINK
BP = PROFIBUS DP EI = EtherNet/IP
EH = EtherCAT EP = PROFINET RT/IRT
7
IO-Link interface, only for LEB, see section
:
NP = Not present IL = IO-Link
6
LEB = basic on-board digital driver
LES = full on-board digital driver
l
k
j
j
X1
MA
MB
SP
AXY
B
Table FS330-12/E

CONNECT
/
*
Bluetooth option, see section
:
T = Bluetooth adapter supplied with the valve
4
Series
number
/
Seals material
,
see section
:
- =
NBR
PE = FKM
BT = NBR low temp.
12
*
*
*
/
Damping plate option
, see section
:
V = plate under the digital driver
8
Smart tuning allows to adjust the
cartridge
dynamic response in order to match different performance requirements.
The
cartridge
is provided with 3 factory settings for the spool control:
- dynamic fast response time and high sensitivity for best dynamic performances. Default factory setting for
cartridge
s
- balanced average response time and sensitivity suitable for major applications
- smooth attenuated response time and sensitivity to improve control stability in critical applications or in environments with electrical disturbances
Smart tuning setting can be switched from Dynamic (default) to Balanced or Smooth via software or fieldbus; if requested, performances can be
further customized directly tuning each single control parameter. For details consult related manuals E-MAN-RI-* and Quickstart, see section
.
For Response time and Bode diagrams see section
.
25
13
3
VALVE SETTINGS AND PROGRAMMING TOOLS - see tech. table GS500
Free downloadable software for PC allows to set all valve functional parameters and to access
complete diagnostic information of digital valve drivers via Bluetooth/USB service port.
Atos E-SW-SETUP PC software supports all Atos digital valve drivers and it is available at
www.atos.com in MyAtos area.
Bluetooth or USB connection
3.2 E-SW-SETUP PC software
3.1 Atos CONNECT mobile App
Free downloadable App for smartphones and tablets which allows quick access to valve
main functional parameters and basic diagnostic information via Bluetooth, thus avoiding
physical cable connection and significantly reducing commissioning time.
Atos CONNECT supports Atos digital valve drivers equipped with E-A-BTH adapter or with
built-in Bluetooth. It does not support valves with p/Q control or axis controls.
LES
mobile App
E-C-SB-USB/M12 cable
E-A-SB-USB/OPT isolator
E-A-BTH adapter
WARNING: drivers USB port is not isolated! For E-C-SB-USB/M12 cable, the use
of E-A-SB-USB/OPT isolator adapter is highly recommended for PC protection
Fieldbus allows valve direct communication with machine control unit for digital reference, valve diagnostics and settings. These execution
allow to operate the valves through fieldbus or analog signals available on the main connector.
7
FIELDBUS - only for LES, see tech. table GS510
5
SMART TUNING
IO-Link allows low cost digital communication between the valve and machine central unit. The valve is directly connected to a port of an IO-Link
master (point-to-point connection) via low-cost unshielded cables for digital reference, diagnostic and settings. The IO-Link master works as a hub
exchanging this information with the machine central unit via fieldbus.
6
IO-LINK - only for LEB, see tech. table GS520
T option adds Bluetooth
®
connectivity to Atos valve drivers thanks to E-A-BTH adapter, which can be left permanently installed on-board, to
allow the Bluetooth connection with the valve drivers at any time. E-A-BTH adapter can also be purchased separately and used to connect with
any supported Atos digital product.
Bluetooth connection to the valve can be protected against unauthorised access by setting a personal password. The adapter leds visually
indicates the status of valve driver and Bluetooth connection.
4
BLUETOOTH OPTION - see tech. table GS500
PC software
LEB
The loss of the pilot pressure causes the undefined position of the main poppet.
The sudden interruption of the power supply during the valve operation causes the immediate shut-off of the main poppet.
This could cause pressure surges in the hydraulic system or high decelerations which may lead to machine damages.
WARNING
WARNING
To avoid overheating and possible damage of the electronic driver, the valves must be never energized without hydraulic supply to the pilot stage.
In case of prolonged pauses of the valve operation during the machine cycle, it is always advisable to disable the driver (option /Q or /Z).
A safety fuse 2,5 A installed on 24V
DC power supply of each valve is always recommended, see also power supply note at sections
17
2
GENERAL NOTES
Atos digital proportionals valves are CE marked according to the applicable directives (e.g. Immunity and Emission EMC Directive).
Installation, wirings and start-up procedures must be performed according to the general prescriptions shown in tech table FS900 and in the
user manuals included in the E-SW-SETUP programming software.
WARNING: for the list of countries where the Bluetooth adapter has been approved, see tech. table GS500
T option is not available for the Indian market, so the Bluetooth adapter must be ordered separately.
V option adds a rubber damping plate between the valve and the on-board digital driver to reduce acceleration mechanical stress on electronic
components, consequently increasing valve life in applications with high vibrations and shocks. For more information see technical table G004.
8
DAMPING PLATE OPTION
Size
16 25 32 40 50 63 80 100 125
250
500
800
1200
2000
3000
4500
7200
9350
350 700 1100 1700 2800 4250 6350 10200 13200
600 1200 1800 2500 4000 6000 10000 16000 22000
Max pressure
[bar]
Ports A, B = 420 X = 350 Y 울 10
Nominal flow of pilot valve at Δp = 70 bar
[l/min]
4 8 20 40 40 100 100 100 100
Leakage of pilot valve at P = 100 bar [l/min] 0,2 0,2 0,3 0,7 0,7 1 1 1 1
Piloting pressure [bar] min: 40% of system pressure max 350 recommended 140 ÷ 160
Piloting volume [cm
3
] 1,6 2,2 7,0 9,4 17,7 32,5 39,5 49,5 124,9
Piloting flow (1) [l/min]
4 5,3 14 19 35,5 56 60 60 88,1
Response time 0 ÷ 100% step signal (2) [ms]
24 25 28 30 30 35 40 50 90
Hysteresis [% of the max regulation]
≤ 0,1
Repeatability [% of the max regulation] ± 0,1
Thermal drift
zero point displacement < 1% at ΔT = 40°C
FS330
10
HYDRAULIC CHARACTERISTICS - based on mineral oil ISO VG 46 at 50 °C
11
ELECTRICAL CHARACTERISTICS
Note:
a maximum time of 800 ms (1000 ms just for size 125), depending on communication type, has to be considered between the driver energizing
with the 24 VDC power supply and when the valve is ready to operate. During this time the current to the valve coils is switched to zero.
(1) With step reference input 0÷100% (2) With pilot pressure = 140 bar, see datailed diagrams in section 13.2
Δp = 5 bar
Δp = 10 bar
Max permissible flow
Nominal flow Δp A-B
[l/min]
9
GENERAL CHARACTERISTICS
Power supplies
Nominal : +24 V
DC
Rectified and filtered : VRMS = 20 ÷ 32 VMAX (ripple max 10 % VPP)
Max power consumption 50 W
Max. solenoid current 2,6 A
Coil resistance R at 20°C
3 ÷ 3,3
Ω
Analog input signals
Voltage: range ±10 V
DC (24 VMAX tolerant) Input impedance: Ri > 50 kΩ
Current: range ±20 mA Input impedance: Ri = 500 Ω
Monitor outputs
Output range: voltage ±10 V
DC @ max 5 mA
current ±20 mA @ max 500 Ω load resistance
Enable input
Range: 0 ÷ 5 V
DC (OFF state), 9 ÷ 24 VDC (ON state), 5 ÷ 9 VDC (not accepted); Input impedance: Ri > 10 kΩ
Fault output
Output range: 0 ÷ 24 V
DC (ON state > [power supply - 2 V] ; OFF state < 1 V ) @ max 50 mA;
external negative voltage not allowed (e.g. due to inductive loads)
Alarms
Solenoid not connected/short circuit, cable break with current reference signal, over/under temperature,
valve spool transducer malfunctions, alarms history storage function
Insulation class
H (180°) Due to the occurring surface temperatures of the solenoid coils,
the European standards ISO 13732-1 and EN982 must be taken into account
Protection degree to DIN EN60529 IP66 / IP67 with mating connectors
Duty factor Continuous rating (ED=100%)
Tropicalization Tropical coating on electronics PCB
Additional characteristics
Short circuit protection of solenoid’s current supply; 3 leds for diagnostic (only for LES); poppet position
control by P.I.D. with rapid solenoid switching; protection against reverse polarity of power supply
Communication interface
USB
Atos ASCII coding
IO-Link
Interface and System
Specification 1.1.3
CANopen
EN50325-4 + DS408
PROFIBUS DP
EN50170-2/IEC61158
EtherCAT
POWERLINK
EtherNet/IP
PROFINET IO RT/IRT
IEC 61158
Communication physical layer
not insulated
USB 2.0 + USB OTG
SDCI
class port B
optical insulated
CAN ISO11898
optical insulated
RS485
Fast Ethernet, insulated
100 Base TX
Recommended wiring cable
LiYCY shielded cables, see section
21
Assembly position Any position
Subplate surface finishing to ISO 4401
Acceptable roughness index: Ra ≤ 0,8, recommended Ra 0,4 – Flatness ratio 0,01/100
MTTFd values according to EN ISO 13849 75 years, for further details see technical table P007
Ambient temperature range
Standard = -20°C ÷ +60°C /PE option = -20°C ÷ +60°C /BT option = -40°C ÷ +60°C
Storage temperature range
Standard = -20°C ÷ +70°C /PE option = -20°C ÷ +70°C /BT option = -40°C ÷ +70°C
Surface protection
Zinc coating with black passivation, galvanic treatment (driver housing)
Corrosion resistance
Salt spray test (EN ISO 9227) > 200 h
Vibration resistance See technical table G004
Compliance
CE according to EMC directive 2014/30/EU (Immunity: EN 61000-6-2; Emission: EN 61000-6-3)
RoHS Directive 2011/65/EU as last update by 2015/863/EU
REACH Regulation (EC) n°1907/2006
13
DIAGRAMS (based on mineral oil ISO VG 46 at 50 °C)
Regulated flow [l/min]
Stroke [% of max]
3
4
3 = LIQZP-L*-322L4
4 = LIQZP-L*-402L4
Regulated flow [l/min]
Stroke [% of max]
1
13.1 Regulation diagrams (values measured at Δp 5 bar)
2
1 = LIQZP-L*-162L4
2 = LIQZP-L*-252L4
Regulated flow [l/min]
Stroke [% of max]
Regulated flow [l/min]
Stroke [% of max]
5
6
5 = LIQZP-L*-50
2L4
6 = LIQZP-L*-63
2L4
7 = LIQZP-L*-802L4
7
1250
1000
750
500
250
0
500
400
300
200
20 40 8060 100
100
0
3000
2400
1800
1200
600
0
5000
4000
3000
2000
1000
0
Stroke [% of max]
9 = LIQZP-L*-1252L4
10000
8000
6000
4000
2000
0
9
Stroke [% of max]
8 = LIQZP-L*-1002L4
7500
6000
4500
3000
1500
0
8
Regulated flow [l/min]
Regulated flow [l/min]
12
SEALS AND HYDRAULIC FLUIDS - for other fluids not included in below table, consult our technical office
Seals, recommended fluid temperature
NBR seals (standard) = -20°C ÷ +60°C, with HFC hydraulic fluids = -20°C ÷ +50°C
FKM seals (/PE option) = -20°C ÷ +80°C
NBR low temp. seals (/BT option) = -40°C ÷ +60°C, with HFC hydraulic fluids = -20°C ÷ +50°C
Recommended viscosity
20÷100 mm
2
/s - max allowed range 15 ÷ 380 mm
2
/s
Hydraulic fluid
Suitable seals type
Classification
Ref. Standard
Mineral oils
NBR, FKM, NBR low temp.
HL, HLP, HLPD, HVLP, HVLPD
DIN 51524
Flame resistant without water
FKM
HFDU, HFDR
ISO 12922
Flame resistant with water
NBR, NBR low temp.
HFC
Max fluid
contamination level
see also filter section at
www.atos.com or KTF catalog
normal operation
longer life
ISO4406 class 18/16/13 NAS1638 class 7
ISO4406 class 16/14/11 NAS1638 class 5
20 40 8060 100
20 40 8060 100
20 40 8060 100
20 40 8060 100 20 40 8060 100
Time [ms]
Time [ms]
Poppet stroke [%]
Poppet stroke [%]
Step signal [%]
Step signal [%]
0-100
0-75
0-50
0-25
13.2 Response time
The response times in below diagrams are measured at different steps of the reference input signal. They have to be considered as average values.
Time [ms] Time [ms]
Poppet stroke [%]
Poppet stroke [%]
Step signal [%]
Step signal [%]
100
75
50
25
014 4228 56
70
014 4228 56
70
LIQZP-16, LIQZP-25 LIQZP-32, LIQZP-40
LIQZP-50
LIQZP-63, LIQZP-80
LIQZP-100
100
75
50
25
100
75
50
25
100
75
50
25
010 3020 40
50
010 3020 40
50
0-100
0-75
0-50
0-25
0-100
0-75
0-50
0-25
0-100
0-75
0-50
0-25
012 3624 48
60
012 3624 48
60
016 4832 64
80
016 4832 64
80
(*) Response time is represented only for 0-100% step; for intermediate steps, the response time increment of presets 2 (balanced) and 3 (smooth)
with respect to the preset 1 (dynamic) is proportional to the step amplitude of the reference input signal
1 = dynamic 2 = balanced (*) 3 = smooth (*)
1
1
1
1
2
3
111123
1
1
1
1
2
3
11112
3
1
1
1
1
23
111123
1
1
1
1
23
111123
Time [ms]
Poppet stroke [%]
Step signal [%]
LIQZP-125
100
75
50
25
0-100
0-75
0-50
0-25
028 8456 112
140
1
1
1
1
23
111123
028 8456 112
140
FS330
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
4
4
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
12
12
3
3
10 50
100
10 50
100
13.5 Bode diagrams LIQZP-L*-322L4
Stated at nominal hydraulic conditions
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
56
56
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
4
4
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
12
1
2
3
3
10 50
100
10 50
100
13.6 Bode diagrams LIQZP-L*-402L4
Stated at nominal hydraulic conditions
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
5
6
13.3 Bode diagrams LIQZP-L*-162L4
Stated at nominal hydraulic conditions
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
1
2
2
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
3
3
10 50
100
10 50
100
4
4
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
56
13.4 Bode diagrams LIQZP-L*-252L4
Stated at nominal hydraulic conditions
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
12
12
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
3
3
10 50
100
10 50
100
4
4
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
56
1
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
4
4
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
12
12
3
3
10 50
100
10 50
100
13.7 Bode diagrams LIQZP-L*-502L4
Stated at nominal hydraulic conditions
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
56
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
4
4
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
12
12
3
3
10 50
100
10 50
100
13.10 Bode diagrams LIQZP-L*-1002L4
Stated at nominal hydraulic conditions
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
56
13.8 Bode diagrams LIQZP-L*-632L4
Stated at nominal hydraulic conditions
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
2
2
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
3
3
10 50
100
10 50
100
4
4
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
56
13.9 Bode diagrams LIQZP-L*-802L4
Stated at nominal hydraulic conditions
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
1
2
12
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
3
3
10 50
100
10 50
100
4
4
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
56
1
1
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
Amplitude ratio [dB]
Frequency [Hz]
Phase [degree]
4
4
+2
0
-3
90°
45°
0°
90°
45°
0°
+2
0
-3
1
2
12
3
3
10 50
100
10 50
100
13.11 Bode diagrams LIQZP-L*-1252L4
Stated at nominal hydraulic conditions
50% ± 5% nominal stroke:
1 = dynamic
2 = balanced
3 = smooth
10% ⟷ 90%
nominal stroke:
4 = dynamic
5 = balanced
6 = smooth
5
6
56
FS330
AIR BLEEDING
16
Sizes 63
÷ 125Size 32 ÷ 50Size 16 ÷ 25
Air suction
SP
MB
MA
SP
MB
MA
6
6
1
2
6
6
1
2
1
2
15
POSSIBLE COMBINED OPTIONS
14
ELECTRONIC OPTIONS - not available for LEB-SN-IL
F = This option permits to monitor the eventual fault condition of the driver, as for example the solenoid short circuit/not connected, reference
signal cable broken for option /I, poppet position transducer broken, etc. - see 17.7 for signal specifications.
I = This option provides 4 ÷ 20 mA current reference and monitor signals, instead of the standard 0 ÷ 10 V
DC.
Input signal can be reconfigured via software selecting between voltage and current, within a maximum range of ±10 VDC or ±20 mA.
It is normally used in case of long distance between the machine control unit and the valve or where the reference signal can be affected
by electrical noise; the valve functioning is disabled in case of reference signal cable breakage.
Q = This option permits to inhibit the valve function without removing the power supply to the driver. Upon disable command the current to the
solenoid is zeroed and the valve’s poppet moves to rest position.
The option /Q is suggested for all cases where the valve has to be frequently inhibited during the machine cycle – see 17.5 for signal
specifications.
Z = This option provides, on the 12 pin main connector, the following additional features:
Fault output signal - see above option /F
Enable input signal - see above option /Q
Repeat enable output signal - only for LEB-SN-NP (see 17.6)
Power supply for driver’s logics and communication - only for LES
(see 17.2)
/FI, /IQ, /IZ
1
Air suction port:
N° 1 plug G1/4” for sizes 16 to 50
N° 1 plug G1/2” for sizes 63 to 100
N° 1 plug G1” for size 125
To be used only in case port A is connected to tank and subjected to neg-
ative pressure, consult our technical office.
2
Air bleeding:
N° 2 plugs G1/4” for size 16 to 100
N° 2 plugs G3/8” for sizes 125
At the machine commissioning it is advisable to bleed the air from piloting
chambers, by loosening the 2 plugs shown in the picture.
Operate the valve for few seconds at low pressure and then lock the plugs.
X1
SP
MB
MA
1
6
2
10
8 (size 125)
17 (size 125)
X1
3
3
3
External pilot pressure (X1):
N° 1 plugs G1/4” for sizes 16 to 100
N° 1 plugs G3/8” for size 125
3
X1
3
Note: /T Bluetooth adapter option and /V damping plate option can be combined with all other options
17
POWER SUPPLY AND SIGNALS SPECIFICATIONS
Generic electrical output signals of the valve (e.g. fault or monitor signals) must not be directly used to activate safety functions, like to switch-ON/OFF
the machine’s safety components, as prescribed by the European standards (Safety requirements of fluid technology systems and components-
hydraulics, ISO 4413).
For LEB-SN-IL signals see section
17.1 Power supply (V+ and V0)
The power supply must be appropriately stabilized or rectified and filtered: apply at least a 10000 μF/40 V capacitance to single phase
rectifiers or a 4700 μF/40 V capacitance to three phase rectifiers. In case of separate power supply see 17.2.
18
17.2 Power supply for driver’s logic and communication (VL+ and VL0) - only for /Z option
The power supply for driver’s logic and communication must be appropriately stabilized or rectified and filtered: apply at least a 10000 μF/40 V
capacitance to single phase rectifiers or a 4700 μF/40 V capacitance to three phase rectifiers.
The separate power supply for driver's logic on pin 9 and 10, allow to remove solenoid power supply from pin 1 and 2 maintaining active the
diagnostics, USB and fieldbus communications.
A safety fuse is required in series to each power supply: 2,5 A time lag fuse.
17.3 Flow reference input signal (Q_INPUT+)
The driver controls in closed loop the valve spool position proportionally to the external reference input signal.
Reference input signal is factory preset according to selected valve code, defaults are 0 ÷ 10 V
DC for standard and 4 ÷ 20 mA for /I option.
Input signal can be reconfigured via software selecting between voltage and current, within a maximum range of ±10 V
DC or ± 20 mA.
Drivers with fieldbus interface can be software set to receive reference signal directly from the machine control unit (fieldbus reference).
Analog reference input signal can be used as on-off commands with input range 0 ÷ 24V
DC.
17.4 Flow monitor output signal (Q_MONITOR) - not for /F
The driver generates an analog output signal proportional to the actual spool position of the valve; the monitor output signal can be soft-
ware set to show other signals available in the driver (e.g. analog reference, fieldbus reference, pilot spool position).
Monitor output signal is factory preset according to selected valve code, defaults are 0 ÷ 10 V
DC for standard and 4 ÷ 20 mA for /I option.
Output signal can be reconfigured via software selecting between voltage and current, within a maximum range of ±10 V
DC or ± 20 mA.
17.5 Enable input signal (ENABLE) - not for standard and /F
To enable the driver, supply a 24 VDC on pin 3 (pin C): Enable input signal allows to enable/disable the current supply to the solenoid,
without removing the electrical power supply to the driver; it is used to active the communication and the other driver functions when the
valve must be disabled for safety reasons. This condition does not comply with norms IEC 61508 and ISO 13849.
Enable input signal can be used as generic digital input by software selection.
17.6 Repeat enable output signal (R_ENABLE) - only for LEB-SN-NP with /Z option
Repeat enable is used as output repeater signal of enable input signal (see 17.5).
17.7 Fault output signal (FAULT) - not for standard and /Q
Fault output signal indicates fault conditions of the driver (solenoid short circuits/not connected, reference signal cable broken for 4 ÷ 20 mA
input, spool position transducer cable broken, etc.). Fault presence corresponds to 0 V
DC, normal working corresponds to 24 VDC.
Fault status is not affected by the Enable input signal. Fault output signal can be used as digital output by software selection.
A safety fuse is required in series to each driver’s logic and communication power supply: 500 mA fast fuse.
18.1 Power supply for IO-Link communication (L+ and L-)
The IO-Link master provides dedicated 24 V
DC power supply for IO-Link communication.
Maximum power consumption: 2 W
Internal electrical isolation of power L+, L- from P24, N24
18.2 Power supply for driver’s logic and valve regulation (P24 and N24)
The IO-Link master provides dedicated 24 V
DC power supply for valve regulation, logics and diagnostics.
Maximum power consumption: 50 W
Internal electrical isolation of power P24, N24 from L+, L-
18.3 IO-Link data line (C/Q)
C/Q signal is used to establish communication between IO-Link master and valve.
18
IO-LINK SIGNALS SPECIFICATIONS - only for LEB-SN-IL
FS330
A
B
C
D
E
F
G
Input - power supply
Gnd - power supply
Gnd - analog signal
Input - on/off signal
Input - analog signal
Software selectable
Input - analog signal
Output - analog signal
Software selectable
Output - on/off signal
TECHNICAL SPECIFICATIONS
NOTES
Standard
/Q
/F
Power supply 24 VDC
Power supply 0 VDC
Analog ground
Enable (24 V
DC) or disable (0 VDC) the valve, referred to V0
Flow reference input signal: ±10 V
DC / ±20 mA maximum range
Defaults are 0 ÷ 10 V
DC for standard and 4 ÷ 20 mA for /I option
Negative reference input signal for Q_INPUT+
Flow monitor output signal: ±10 V
DC / ±20 mA maximum range
Defaults are 0 ÷ 10 V
DC for standard and 4 ÷ 20 mA for /I option
Fault (0 V
DC) or normal working (24 VDC)
Internally connected to the driver housing
19.1 Main connector signals - 7 pin - standard, /F and /Q options
19
ELECTRONIC CONNECTIONS AND LEDS
PIN
19.2 Main connector signal - 12 pin - /Z option
Note: do not disconnect VL0 before VL+ when the driver is connected to PC USB port
1
2
3
4
5
6
7
8
9
10
11
PE
V+
V0
ENABLE referred to:
V0 VL0
Q_INPUT+
INPUT-
Q_MONITOR referred to:
AGND VL0
AGND
NC
R_ENABLE
NC
NC
VL+
NC
VL0
FAULT referred to:
V0 VL0
EARTH
Power supply 24 VDC
Power supply 0 VDC
Enable (24 V
DC
) or disable (0 V
DC
) the valve
Flow reference input signal: ±10 V
DC / ±20 mA maximum range
Defaults are
0 ÷ 10 VDC for standard and 4 ÷ 20 mA for /I option
Negative reference input signal for Q_INPUT+
Flow monitor output signal: ±10 V
DC / ±20 mA maximum range
Defaults are
0 ÷ 10 VDC for standard and 4 ÷ 20 mA for /I option
Analog ground
Do not connect
Repeat enable, output repeater signal of enable input, referred to V0
Do not connect
Do not connect
Power supply 24 V
DC for driver’s logic and communication
Do not connect
Power supply 0 V
DC for driver’s logic and communication
Fault (0 V
DC
) or normal working (24 V
DC
)
Internally connected to the driver housing
Input - power supply
Gnd - power supply
Input - on/off signal
Input - analog signal
Software selectable
Input - analog signal
Input - analog signal
Software selectable
Output - analog signal
Gnd - analog signal
Output - on/off signal
Input - power supply
Gnd - power supply
Output - on/off signal
PIN
TECHNICAL SPECIFICATIONS
NOTES
LEB /Z LES /Z
V+
V0
AGND AGND
ENABLE
Q_INPUT+
INPUT-
Q_MONITOR referred to:
AGND V0
FAULT
EARTH
EH, EW, EI, EP fieldbus execution, connector - M12 - 4 pin
PIN SIGNAL
TECHNICAL SPECIFICATION (1)
1
TX+
Transmitter
2
RX+
Receiver
3
TX-
Transmitter
4
RX-
Receiver
SHIELD
BC fieldbus execution, connector - M12 - 5 pin
PIN SIGNAL
TECHNICAL SPECIFICATION (1)
1
CAN_SHLD
Shield
2
not used
- pass-through connection (2)
3
CAN_GND
Signal zero data line
4
CAN_H
Bus line (high)
5
CAN_L
Bus line (low)
USB connector - M12 - 5 pin always present
PIN SIGNAL
TECHNICAL SPECIFICATION (1)
1
+5V_USB
Power supply
2
ID
Identification
3
GND_USB
Signal zero data line
4
D-
Data line -
5
D+
Data line +
BP fieldbus execution, connector - M12 - 5 pin
PIN SIGNAL
TECHNICAL SPECIFICATION (1)
1
+5V
Termination supply signal
2
LINE-A
Bus line (high)
3
DGND
Data line and termination signal zero
4
LINE-B
Bus line (low)
5
SHIELD
19.4 Communications connectors -
(1) shield connection on connector’s housing is recommended (2) Pin 2 can be fed with external +5V supply of CAN interface
PIN SIGNAL TECHNICAL SPECIFICATIONS NOTES
1 L+
Power supply 24 V
DC for IO-Link communication Input - power supply
2 P24
Power supply 24 V
DC for valve regulation, logics and diagnostics Input - power supply
3 L-
Power supply 0 V
DC for IO-Link communication Gnd - power supply
4 C/Q
IO-Link data line Input / Output - signal
5 N24
Power supply 0 V
DC for valve regulation, logics and diagnostics Gnd - power supply
19.3 IO-Link connector signals - M12 - 5 pin - Coding A, port class B only for LEB-SN-IL
Note: L+, L- and P24, N24 are electrically isolated
L-
C/Q
L+
P24
N24
L-
C/Q
L+
P24
N24
L-
C/Q
L+
P24
N24
L-
C/Q
L+
(1) Maximum power consumption: 50 W
(2) External power supply
Valve to Master connection examples
(2)
Valve
Class
B
Master
Class
B
Valve
Class
B
Master
Class
A
(1)
(1)
(1)
(1)
FS330
19.6 LEB-SN-IL connections layout
(1) Pin layout always referred to driver’s view
19.5 LEB-SN-NP connections layout
MAIN CONNECTORS
A2
A4
A3A1
A2
A4
A1
A3
Ø 28Ø 29
~ 93
~ 100
PG13.5
PG16
Ø 28Ø 29
~ 60
~ 76PG11
PG11
ZM-12P
12 pin - metallic (1)
ZH-12P
12 pin - plastic
ZM-7P
7 pin - metallic (1)
ZH-7P
7 pin - plastic
BLUETOOTH ADAPTER AND USB CONNECTOR
male - 7 pin (2)
male - 12 pin (2)
Standard, /Q, /F
/Z
(1) Use of metallic connectors is strongly recommended in order to fulfill EMC requirements (2) Pin layout always referred to driver’s view
DRIVER OVERVIEW
DRIVER OVERVIEW
TRANSDUCER CONNECTOR
35.5
~ 23
POPPET POSITION
MAIN STAGE
DO NOT REMOVE
TRANSDUCER CONNECTOR
35.5
~ 23
POPPET POSITION
MAIN STAGE
DO NOT REMOVE
IO-Link CONNECTOR - BLUETOOTH ADAPTER AND USB CONNECTOR
A
A
Ø 20
~ 58
13.5
Ø14
B
B
B
~ 50
Ø15
58
18
B
male - 5 pin (1)
IO-Link
ZM-5PF
5 pin - metallic
female (2)
Bluetooth/USB
USB cap
Tightening torque:
0,6 Nm
E-C-SB-USB/M12
USB CABLE - cable length 4m
E-A-BTH
Bluetooth adapter
B
~ 50
Ø15
13.5
Ø14
58
18
B
B
B
E-C-SB-USB/M12
USB CABLE - cable length 4m
Bluetooth/USB
USB cap
Tightening torque:
0,6 Nm
female (2)
E-A-BTH
Bluetooth adapter
Three leds show driver operative conditions for immediate basic diagnostics. Please refer to the driver user manual for detailed information.
19.8 Diagnostic LEDs - only for LES
NP
Not Present
BC
CANopen
BP
PROFIBUS DP
EH
EtherCAT
EW
POWERLINK
EI
EtherNet/IP
EP
PROFINET
L1
VALVE STATUS LINK/ACT
L2
NETWORK STATUS NETWORK STATUS
L3
SOLENOID STATUS LINK/ACT
FIELDBUS
LEDS
L1 L2 L3
19.7 LES connections layout
MAIN CONNECTORS
A2
A4
A3A1
A2
A4
A1
A3
Ø 28Ø 29
~ 93
~ 100
PG13.5
PG16
Ø 28
Ø 29
~ 60
~ 76PG11
PG11
Ø 15
~ 62
Ø 20
~ 51
~ 62
Ø 20
~ 46
Ø 20
Ø 20
~ 58
~ 58
Ø 15
~ 62
Ø 20
~ 62
Ø 20
B
~ 50
Ø15
58
18
B
13.5
Ø14
35.5
~ 23
FIELDBUS CONNECTORS
PROFIBUS DP
ZM-5PM/BP
ZM-5PM
ZM-5PF
ZM-4PM/E
CANopen
ZM-5PF/BP
E-TRM-BC-M12/5PM
female (2)
male (2)
female - INPUT (2)
ZM-4PM/E
E-TRM-BP-M12/4PF
E-C-SB-USB/M12
USB CABLE - length 4m
female (2)
PROFIBUS DP
EtherCAT
POWERLINK
EtherNet/IP
PROFINET
CANopen
female - OUTPUT (2)
EtherCAT
POWERLINK
EtherNet/IP
PROFINET
male - 7 pin (2)
male - 12 pin (2)
Bluetooth/USB
Standard, /Q, /F /Z
female (2)
male (2)
(1) Use of metallic connectors is strongly recommended in order to fulfill EMC requirements (2) Pin layout always referred to driver’s view
ZM-12P
12 pin - metallic (1)
ZH-12P
12 pin - plastic
ZM-7P
7 pin - metallic (1)
ZH-7P
7 pin - plastic
Terminator
Terminator
Tightening torque:
0,6 Nm
DRIVER OVERVIEW
SN NP BC , BP EH , EW , EI , EP
USB cap
TRANSDUCERS CONNECTORS - BLUETOOTH ADAPTER AND USB CONNECTOR
E-A-BTH
Bluetooth adapter
POPPET POSITION
MAIN STAGE
DO NOT REMOVE
FS330
21
CONNECTORS CHARACTERISTICS - to be ordered separately
CONNECTOR TYPE POWER SUPPLY AND SIGNALS POWER SUPPLY AND SIGNALS
CODE ZM-7P ZH-7P
Type 7pin female straight circular 7pin female straight circular
Standard According to MIL-C-5015 According to MIL-C-5015
Material Metallic Plastic reinforced with fiber glass
Cable gland PG11 PG11
Recommended cable
LiYCY 7 x 0,75 mm
2
max 20 m (logic and power supply)
or LiYCY 7 x 1 mm
2
max 40 m (logic and power supply)
LiYCY 7 x 0,75 mm
2
max 20 m (logic and power supply)
or LiYCY 7 x 1 mm
2
max 40 m (logic and power supply)
Conductor size up to 1 mm
2
- available for 7 wires up to 1 mm
2
- available for 7 wires
Connection type to solder to solder
Protection (EN 60529) IP 67 IP 67
CONNECTOR TYPE POWER SUPPLY AND SIGNALS POWER SUPPLY AND SIGNALS
CODE ZM-12P ZH-12P
Type 12pin female straight circular 12pin female straight circular
Standard DIN 43651 DIN 43651
Material Metallic Plastic reinforced with fiber glass
Cable gland PG13,5 PG16
Recommended cable LiYCY 12 x 0,75 mm
2
max 20 m (logic and power supply)
LiYCY 10 x 0,14mm
2
max 40 m (logic)
LiYY 3 x 1mm
2
max 40 m (power supply)
Conductor size 0,5 mm
2
to 1,5 mm
2
- available for 12 wires
0,14 mm
2
to 0,5 mm
2
- available for 9 wires
0,5 mm
2
to 1,5 mm
2
- available for 3 wires
Connection type to crimp to crimp
Protection (EN 60529) IP 67 IP 67
21.1 Main connectors - 7 pin
21.2 Main connectors - 12 pin
21.3 IO-Link connector - only for LEB-SN-IL
CONNECTOR TYPE IL IO-Link
CODE ZM-5PF
Type 5pin female straight circular
Standard M12 coding A – IEC 61076-2-101
Material Metallic
Cable gland Pressure nut - cable diameter 6÷8 mm
Recommended cable 5 x 0,75 mm
2
max 20 m
Connection type screw terminal
Protection (EN 60529) IP 67
21.4 Fieldbus communication connectors
CONNECTOR TYPE
BC CANopen (1) BP PROFIBUS DP (1)
EH EtherCAT, EW POWERLINK,
EI EtherNet/IP, EP PROFINET (2)
CODE ZM-5PF ZM-5PM ZM-5PF/BP ZM-5PM/BP ZM-4PM/E
Type
5 pin female
straight circular
5 pin male
straight circular
5 pin female
straight circular
5 pin male
straight circular
4 pin male
straight circular
Standard M12 coding A – IEC 61076-2-101 M12 coding B – IEC 61076-2-101 M12 coding D – IEC 61076-2-101
Material Metallic Metallic Metallic
Cable gland Pressure nut - cable diameter 6÷8 mm Pressure nut - cable diameter 6÷8 mm Pressure nut - cable diameter 4÷8 mm
Cable CANbus Standard (DR 303-1) PROFIBUS DP Standard Ethernet standard CAT-5
Connection type screw terminal screw terminal terminal block
Protection (EN 60529) IP67 IP 67 IP 67
(1) E-TRM-** terminators can be ordered separately - see tech table GS500 (2) Internally terminated
20
IN / OUT FIELDBUS COMMUNICATION CONNECTORS
Two fieldbus communication connectors are always available for digital drivers executions BC, BP, EH, EW, EI, EP.
This features allows considerable technical advantages in terms of installation simplicity, wirings reduction and
also avoid the usage expensive T-connectors.
For BC and BP executions the fieldbus connectors have an internal pass-through connection and can be used
like end point of the fieldbus network, using an external terminator (see tech table GS500).
For EH, EW, EI and EP executions the external terminators are not required: each connector is internally terminated.
BC and BP pass-through connection
fieldbus
network
fieldbus
interface
fieldbus
network
23
MAIN CONNECTORS INSTALLATION DIMENSIONS [mm]
(1) Fastening bolts supplied with the valve
Reference dimension
Main
connector
code
Valve size
16 25 32 40 50 63 80 100 125
B
ZM-7P 32 32 32 40 45 68 68 80 142
ZH-7P
(1) (1) (1) (1)
29 52 52 64 125
ZM-12P
(1) (1) (1) (1) (1)
35 35 47 108
ZH-12P
(1) (1) (1) (1) (1) (1) (2)
40 101
C (max)
- 104 114 121 134 141 172 202 229 271
D for standard valve
- 124 134 141 154 161 192 222 249 291
D for /V option
- 139 149 156 169 176 207 237 264 306
Above dimenions refer to the main connector fully screwed to driver’s connector. The space A = 15 mm to remove the connector must be considered
(1) The connector installation can be performed only if the valve’s driver protrudes from the edge of the relevant mounting manifold as rapre-
sented in above “Installation 2”
(2) The connector installation may be critic, depending to the cable size and bending radius
Installation 1 - possible interference between manifold and main
connector
A
B
C
D
15 mm space to remove the 7 or 12 pin main connectors
Clearance between main connector to valve’s mounting surface.
See the below table to verify eventual interferences, depending
to the valve size and connector type
A =
B =
Max manifold dimension to avoid interference with the main con-
nector, see below table
C =
Installation 2 - no interference
Type Size Fastening bolts (1) Mass [kg]
LIQZP
16
4 socket head screws M8x90 class 12.9
Tightening torque = 35 Nm
5,6
25
4 socket head screws M12x100 class 12.9
Tightening torque = 125 Nm
8,2
32
4 socket head screws M16x60 class 12.9
Tightening torque = 300 Nm
10,9
40
4 socket head screws M20x70 class 12.9
Tightening torque = 600 Nm
16,7
50
4 socket head screws M20x80 class 12.9
Tightening torque = 600 Nm
23,9
63
4 socket head screws M30x120 class 12.9
Tightening torque = 2100 Nm
44,0
80
8 socket head screws M24x80 class 12.9
Tightening torque = 1000 Nm
71,6
100
8 socket head screws M30x120 class 12.9
Tightening torque = 2100 Nm
122,5
125
8 socket head screws M36x260 class 12.9
Tightening torque = 3600 Nm
375
22
FASTENING BOLTS AND VALVE MASS
100x1005
30
LIQZP-LEB-*-162
LIQZP-LES-*-162
65x65
5
75
203
24
INSTALLATION DIMENSIONS [mm]
H
LIQZP-LEB-*-322
LIQZP-LES-*-322
LIQZP-LEB-*-402
LIQZP-LES-*-402
FS330
~90
C20
A1
85x85
5
80
265
H
218
B
~90
125
C20
A1
B
~90
125
C20
A1
B
~98
125
C20
125x1255A1
39
253
(3)
LIQZP A1
B (1) C (2)
H
LEB - SN - IL 140 60 - 242
LEB - SN - NP 140 60 - 242
LES - SN - NP, BC, BP, EH 140 60 58 235
LES - SN - EW, EI, EP 155 60 58 235
Option /V +15 -
235
H
(3)
(3)
(3)
265
125
B
265
LIQZP-LEB-*-252
LIQZP-LES-*-252
273
Note: for mounting surface and cavity dimensions, see table P006
(1) The indicated dimension refers to the main connector ZM-7P. See section
for main connectors installation dimensions
(2) The indicated dimension refers to the longer connectors or Bluetooth adapter
For dimensions of connectors and Bluetooth adapter, see sections 19.5, 19.6 and 19.7
(3) Space required for connection cable and for connector removal
23
LIQZP-LEB-*-502
LIQZP-LES-*-502
140x140
49
129
295
5
A1
76
142
314
LIQZP-LEB-*-632
LIQZP-LES-*-632
LIQZP-LEB-*-802
LIQZP-LES-*-802
LIQZP-LEB-*-1002
LIQZP-LES-*-1002
45
162
334
70
178
365
Ø300
Note: for mounting surface and cavity dimensions, see table P006
B
~105
125
C
20
180x1805A2
B
~128
125
C
20
Ø250
A2
B
~128
125
C
20
B
~140
125
C
20
A2
~280
~303
~303
~303
LIQZP A1 A2
B (1) C (2)
LEB - SN - IL 140 150 60 -
LEB - SN - NP 140 150 60 -
LES - SN - NP, BC, BP, EH 140 150 60 58
LES - SN - EW, EI, EP 155 165 60 58
Option /V +15 +15 -
(3)
(3)
(3)
(3)
(1) The indicated dimension refers to the main connector ZM-7P. See section
for main connectors installation dimensions
(2) The indicated dimension refers to the longer connectors or Bluetooth adapter
For dimensions of connectors and Bluetooth adapter, see sections 19.5, 19.6 and 19.7
(3) Space required for connection cable and for connector removal
23
01/25
25
RELATED DOCUMENTATION
LIQZP-LEB-*-1252
LIQZP-LES-*-1252
200
318
503
Ø380
FS001 Basics for digital electrohydraulics
FS900 Operating and maintenance information for proportional valves
GS500 Programming tools
GS510 Fieldbus
GS520 IO-Link interface
K800 Electric and electronic connectors
P006 Mounting surfaces and cavities for cartridge valves
QB340 Quickstart for LEB valves commissioning
QF340 Quickstart for LES valves commissioning
E-MAN-RI-LEB TEB/LEB user manual
E-MAN-RI-LES TES/LES user manual
A2
B
~200
125
C
20
LIQZP A2
B (1) C (2)
LEB - SN - IL 140 60 -
LEB - SN - NP 140 60 -
LES - SN - NP, BC, BP, EH 140 60 58
LES - SN - EW, EI, EP 155 60 58
Option /V +15 -
385
(3)
Note: for mounting surface and cavity dimensions, see table P006
(1) The indicated dimension refers to the main connector ZM-7P. See section
for main connectors installation dimensions
(2) The indicated dimension refers to the longer connectors or Bluetooth adapter
For dimensions of connectors and Bluetooth adapter, see sections 19.5, 19.6 and 19.7
(3) Space required for connection cable and for connector removal
23