163
VANE PUMPS
"PV2R" Series
Single Vane Pumps
B
"PV2R" Series Single Vane Pumps
2
Graphic Symbol
F-
Series
Number
Special Seals
F:
For phosphate
ester type
fluids (Omit
if not
required)
PV2R2
Nominal
Displacement
3
cm /rev
Design
Standards
Design
Number
A:
Upwards
(Normal)
Refer to
42
41
31
30
PV2R1 -6 -L -R A -42
-
*
A
Type of
Mounting
Shaft
Rotation
Discharge
Port
Position
Suction
Port
Position
A:
Upwards
(Normal)
R:
Clockwise
(Normal)
L:
Foot
Mounting
F:
Flange
Mounting
PV2R3
PV2R4
6, 8, 10, 12
14, 17, 19
23, 25, 31
PV2R1
41, 47, 53
59, 65
76, 94, 116
136, 153, 184
200, 237
Pump
Model
Numbers
PV2R1
PV2R2
PV2R3
PV2R4
Name
of
Port
Suction
Discharge
Suction
Discharge
Suction
Discharge
Suction
Discharge
Japanese
Standard "JIS"
F5-08-A-10
F5-04-A-10
F5-10-A-10
F5-06-A-10
F5-16-A-10
F5-10-A-10
F5-24-A-10
F5-12-A-10
European
Design
Standard
F5-08-A-1080
F5-04-A-1080
F5-10-A-1080
F5-06-A-1080
F5-16-A-1080
F5-10-A-1080
F5-12-A-1080
N. American
Design
Standard
Japanese
Standard "JIS"
European
Design
Standard
F5-08-B-10
F5-04-B-10
F5-10-B-10
F5-06-B-10
F5-16-B-10
F5-10-B-10
F5-24-B-10
F5-12-B-10
F5-08-B-1090
F5-04-B-1090
F5-10-B-1090
F5-06-B-1090
F5-16-B-1090
F5-10-B-1090
F5-24-B-1090
F5-12-B-1090
N. American
Design
Standard
Japanese
Standard "JIS"
European
Design
Standard
F5-08-C-10
F5-04-C-10
F5-10-C-10
F5-06-C-10
F5-16-C-10
F5-10-C-10
F5-24-C-10
F5-12-C-10
F5-08-C-1090
F5-04-C-1090
F5-10-C-1090
F5-06-C-1090
F5-16-C-1090
F5-10-C-1090
F5-24-C-1090
F5-12-C-1090
N. American
Design
Standard
Pipe Flange Kit Numbers
Threaded Connection Socket Welding
Butt Welding
Model Number Designation
Pipe Flange Kits
1. Available to supply pump with anti-clockwise rotation.
Consult Yuken for details.
Pipe flange kits are available. When ordering, specify the kit number from the table below.
2.Design Standards:None.....Japanese Standard "JIS"
80
90
.........
.........
European Design Standard
N. American Design Standard
Notes: Special seals (Viton seals) are required when phosphate ester type fluids are used. (Prefix
"F-"
to the pipe flange kit number when ordering.)
Details of the pipe flange kits are shown on
page 824.
"PV2R" Series Single Vane Pumps
2
1
22
In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of the
flanges. Therefore, please pay cautious attention to the operating pressure when the socket welding flanges are used.
1.
As dimensions of the pipe flange mounting surface are conformed to SAE 4 Bolt Split Flange (Standard Pressure Series), pipe flanges conforming to
the SAE Standards can be used.
2.
These pumps are of high pressure and high performance, which have been developed especially for low noise operation.
To comply with a variety of applications including injection moulding machines, PV2R series single pumps provide the
output flow of such a wide range as from 5.8 to 237 cm
3
/rev (.354 to 14.46 cu.in./rev).
The intergral driving parts of the pumps are combined into a kit form and available for supply as a cartridge kit.
Therefore, the replacement of the driving parts can be done easily.
(Viewed from Shaft End)
1