Pressure Reducing (and Check) Valves
252
1.6 (3.5)
2.4 (5.3)
3.0 (6.6)
4.8 (10.6)
5.7 (12.6)
Valve Model
Numbers
RG-03
RG-06
RG-10
RCG-03
RCG-06
RCG-10
Socket Head Cap Screw
Japanese Std. "JIS" and European Design Std. N. American Design Std.
Qty.
M10 50 Lg.
M10 50 Lg.
M10 50 Lg.
M10 70 Lg.
M10
80 Lg.
M10
90 Lg.
3/8-16 UNC 2 Lg.
3/8-16 UNC 2 Lg.
3/8-16 UNC 2 Lg.
3/8-16 UNC 2-3/4 Lg.
3/8-16 UNC 3-1/4 Lg.
3/8-16 UNC 3-1/2 Lg.
4
4
6
4
4
6
Valve
Model
Numbers
-03
RG
RCG
-06
RG
RCG
-10
RG
RCG
Japanese Standard "JIS"
Sub-plate
Model Numbers
Thread
Size
European Design Standard
Sub-plate
Model Numbers
Thread
Size
N. American Design Standard
Sub-plate
Model Numbers
Thread
Size
Approx. Mass
kg (lbs.)
HGM-03-20
HGM-03X-20
HGM-06-20
HGM-06X-20
HGM-10-20
HGM-10X-20
Rc 3/8
Rc 1/2
Rc 3/4
Rc 1
Rc 1-1/4
Rc 1-1/2
HGM-03-2080
HGM-03X-2080
HGM-06-2080
HGM-06X-2080
HGM-10-2080
HGM-10X-2080
3/8 BSP.F
1/2 BSP.F
3/4 BSP.F
1 BSP.F
1-1/4 BSP.F
1-1/2 BSP.F
HGM-03-2090
HGM-03X-2090
HGM-06-2090
HGM-06X-2090
HGM-10-2090
HGM-10X-2090
3/8 NPT
1/2 NPT
3/4 NPT
1 NPT
1-1/4 NPT
1-1/2 NPT
Attachment
Mounting bolts
Sub-plate
Instructions
Model Number Designation
Special Seals
for Phosphate
Ester Type
Fluids
(Omit if not
required)
F:
03
06
10
03
06
10
03
06
10
03
06
10
C:
3.5-14
(510-2030)
H:
7-20.5
(1020-2970)
B:
0.7-7
(102-1020)
Pressure
Reducing
Valves
R:
Pressure
Reducing and
Check Valves
RC:
Threaded
Connection
T :
Sub-plate
Mounting
G:
Threaded
Connection
T :
Sub-plate
Mounting
G:
22
22
22
22
22
22
22
22
22
22
22
22
F- R
Special Seals Series Number
T
Type of Mounting
-22
Design
Number
*
Design Standards
-03 -B
Pres. Adj. Range
MPa (PSI)
Valve
Size
None:
Japanese Std. "JIS"
80 :
European Design Std.
90 :
N.American Design Std.
None:
Japanese Std. "JIS"
80 :
European Design Std.
90 :
N.American Design Std.
Sub-plates are available. Specify the sub-plate model number from the table above. When sub-plates are not used, the mounting
surface should have a good machined finish.
The sub-plates are the same as those for H type pressure control valves. With the reducing and check valve, the sub-plate is used in a
position 180° turned (upside down) from the normal position. When mounting the sub-plate, be sure to bring the valve locating pin to
the sub-plate pin hole. For dimensions, see
page 244 to 246.
To adjust the pressure, loosen the lock nut and turn the pressure adjustment handle slowly clockwise for higher
pressures and anti-clockwise for lower pressures. After adjustments, do not forget to tighten the lock nut.
Connect the drain port directly to the reservoir in which case the pressure at the drain port should be kept at a low
back pressure close to the atmospheric pressure.
In case of "Threaded Connections", there are two threaded connection type primary pressure ports. They can be
connected each other in-line; one as an inlet and the other as an outlet or the valve can be used by plugging one of the
pressure ports.