Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 1/19 Edition: 24 04 3.0-30E
APPLICATION
The areas of application oer great diversity. PMV are used where
compact installation dimensions are required and a function requires
sensitively controlled.
Typical applications are cylinder and motor controls for all handling
functions as in loading cranes, telescopic handlers, aerial platforms,
municipal vehicles, construction machinery, drilling equipment, agricul-
tural and forestry machinery, oshore applications, underground mining.
DESCRIPTION
The PMV concept is constructed to oer a high level of modularity. It
allows a conguration of individual modules, which are available as
pre-assembled units with their own type code. Modications, to and
between them, can also be carried out quickly in the eld.
Due to the modular design, special solutions can also be created in a
exible manner. For example, counterbalance valves integrated in the
connection plate or operated non-return valves can be integrated. By
means of the 2-way pressure compensator, the ow can be controlled
Independent from the load.
• Veryexiblycombinableandloadindependent
• Pre-compensatedandload-sensing
• Highcorrosionprotection,K8(Zn/Ni)
• Stainlesssteeladjustingscrews
• Q
max
=400l/min(withoutcompensator450l/min)
• p
max
=420bar
PMV-22
OVERVIEW PMV
OVERVIEW PMV
PMV-P22 (Electrical-pro-
portional)
PMV-T22 (tie rod)
PMV-H22 (Hydraulic)
PMV-A22 (end cap)
PMV-D22 (spring cap)PMV-B00 Option
(pump unloading)
PMV-B00-A option (an-
ti-saturation, LS amplifi er)
PMV-L22 (Manual)PMV-S22 (spool)
PMV-B22 (inlet plate)
PMV-M22 (control
section)
PMV-C22 (connection
plate)
PMV-E22 (end plate)
P
roportional Mobile Valves
A-SIDE B-SIDE
www.wandfluh.com Illustrations are not binding Data subject to change 2/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
OVERVIEW PMV EXAMPLE UNIT
1: Inlet plate
2: Input pressure limitation
3: Control section
4: 2-way compensator with delta p setting
5: Stroke limitation
6: LS relief valve A
7: LS relief valve B
8: Proportional pressure reducing valve A
9: Proportional pressure reducing valve B
10: Connection plate with LS pressure reliefs
11: Stroke limitation
12: End cap
13: Spring cap with manual actuation
14: Connection plate with LS pressure reliefs and suction function
15: Connection plate
16: 2-way compensator with delta p setting and check valve function
17: End plate
F
Released
D
Radiuses,
m
H
Envelope requirement acc.to
>3-6
Page 1 of 1C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-22\PMV-22 Komplette Ventile\0304409
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
±0.1
>0,5-3
±0.2
±0.3
Format
±0.1
>6-30 >30-120
±0.2
G
±0.5
+0.4
±1
H
A0
to third parties without permission in written form.
C
B
A
m
Concentricity, axial runout
M 1:2
H
-0.3
1413
H
00
Violation is illegal and will be legally prosecuted.
PMV-22
Edges acc. ISO 13715
ISO 14405
erstellt
Surface finish
Project number:
Replacement for:
Rev.
P/N:
Doc.-No.
E
ECN-Description
ECN
NameDate
7VIAL
27.07.2022
Checked
Nominal dimension
Ra 3.2
0304409
Linear dimensions
68.192 kg
Drawn
Weight
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0304406 / Configuration 001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
15
153.6
M
1
0
x
1
5
M
1
0
x1
5
151.6
M
1
0
x
1
5
31.6
10
25
M
1
0
x1
5
61 61
200
389
M
1
0
x1
5
45
60 85 (R22; 90) 61 61
10
163.6
31 81
10
M
1
0
x
1
5
(
4
x
)
3
0
°
183.6 103.1 94
3
0
°
1
6
0
49
52.5
123.3
34
66.5
125.8
61
P Pilot
A B LSBLSA
PT T
b a
3
4
5
P Pilot
A B LSBLSA
PT T
b a
8 9
12
A B
15
A BYa Yb
6 7
P Pilot
A B LSBLSA
PT T
b a
11
A BYa Yb
10
13
T2
P
Z
17
1: Inlet plate
2: Input pressure limitation
3: Control section
4: 2-way compensator with delta p setting
5: Stroke limitation
6: LS relief valve A
7: LS relief valve B
8: Proportional pressure reducing valve A
9: Proportional pressure reducing valve B
10: Connection plate with LS pressure reliefs
11: Stroke limitation
12: End cap
13: Spring cap with manual actuation
14: Connection plate with LS pressure reliefs and suction function
15: Connection plate
16: 2-way compensator with delta p setting and check valve function
17: End plate
A BYa Yb
14
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø0.6
Plug
ø**
T1
L
ø**
P Pilot
2 1
16
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A
B
LS T
T
LS
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A3
von
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 3/19 Edition: 24 04 3.0-30E
ELECTRICAL SPECIFICATIONS
Nominal voltage 12 VDC or 24 VDC
Type of protection Connection version D: IP65
Connection version J: IP66
Connection version G: IP67 and IP69K
Connection Connector socket D: DIN, EN175301-
803 / ISO 4400
Connector socket J: AMP Junior Timer
Connector socket G: Deutsch DT04 – 2P
Relative duty factor 100% DF
Dither frequency for
proportional solenoids
(recommended)
100 Hz
GENERAL SPECIFICATIONS
Designation Proportional spool valve
Construction type Sectional design pilot operated
Mounting type Inline mounting
Any mounting position
Dimension Nominal size 22
Number of control
sections
Max. 10
Temperature range
environment
-30…+70 °C
MTTFd 150 years
ACTUATION
Possible modes of
operation
• Electrically pilot operated (12V/24V)
• Hydraulically pilot operated (6-22 bar)
• Manual
Manual override (lever) optional with electric and hydraulic operating
form.
SURFACETREATMENTSK8
• Most external parts are zinc-nickel coated (K8).
• The xing screws are zinc coated.
• Adjusting screws are in stainless steel.
SEALING MATERIALS
HNBR as standard, FKM (Viton) as option
HYDRAULIC SPECIFICATIONS
Operating pressure P,
A/B
p
max
= 420 bar
Tank pressure p
Tmax
= 35 bar
Maximum volume ow
Q
max
Port P1 or P2: 400 l/min
Port P1 and P2: 800 l/min
Port A/B: 400 l/min and without compen-
sator 450 l/min.
Pressure setting range 50…420 bar
Hysteresis ≤ 3 % at optimal dither signal
Fluid Mineral-based or synthetic hydraulic uid
with lubricating properties
Viscosity range 12 mm
2
/s…320 mm
2
/s
Temperature range uid -30…+80 °C (HNBR)
-15…+80 °C (Viton)
Contamination ecency Class 18 / 16 / 13 ISO 4406
Filtration Recommended ltration grade beta
6...10 >= 75
www.wandfluh.com Illustrations are not binding Data subject to change 4/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
FIXED DISPLACEMENT PUMP
The PMV inlet plate type B/R22-F/H is used for xed displacement
pumps.
This inlet plate includes a 3-way pressure compensator for the recircu-
lation function, as well as a maximum pressure setting. The adjustment
range of the maximum pressure setting is 14 to 420 bar.
The inlet plate type B/R22-F is suitable for ows up to 250 l/min with
one control section. For higher ow rates, the inlet plate type B/R22-H
is required. Max. ow with the H-compensator is 310 l/min.
If no control section is actuated, the pump ow recirculates to the tank
without pressure.
When one or more control sections are actuated, the highest load
pressure signal is fed back to the 3-way pressure compensator, pres-
surising the pump line.
VARIABLEPUMP(LSPUMP)
The PMV inlet plate type B/R22-V/P is used for load sensing pumps
(LS pumps).
The PMV inlet plate of type B/R22-V has the ports P, T and the LS signal.
The LS signal can be adjusted up to 420 bar via the pressure setting.
The type B/R22-P inlet plate also has a maximum pressure setting in
P to provide additional protection for the system.
SCHEMEF/H
SCHEMEV/P
INLET PLATE PMV-B22 AND R22
PMV - - - - - - K8
Platetype
B22 Inlet plate size 22
R22 Reduction plate size 22/16
Plateversion
F For xed displacement pump
H For xed displacement pump high ow
V For LS pump
P For LS pump with main relief valve in P
Max.pressuremainrelief
1 p
max
100 bar
4 p
max
420 bar
Portconnection
G Thread in BSP
S Thread in SAE-ORB
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
PMV-B22-F/H....NEW
PMV-B22-V.....NEW
PMV-B16-F/H....NEW
PMV-R22-V......
PMV-R22-P.....NEWPMV-B22-P....NEW
PMV-B16-P.....NEW
PMV-B16-V....NEW
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
P-Pilot
PMV-R22-F/H......NEW
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LSL P
LSP TMP
ø**
T1
ø**
ø**
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø**
T1
L
ø**
P Pilot
PLUG
ø0.6
P Pilot
P pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
T1
L
ø**
ø**
P pilot
Page 4 & 5, PMV16 & 22 Datasheets
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS
L
P
LSP TMP
ø**
T1
ø**
ø**
PLUG
ø0.6
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS P
LSP TMP
ø**
T1
ø**
ø**
L
ø0.6
PLUG
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
ø0.6
PLUG
MP
Pls. update these two schemes. T1 line was missing.
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
PMV-B22-F/H....NEW
PMV-B22-V.....NEW
PMV-B16-F/H....NEW
PMV-R22-V......
PMV-R22-P.....NEWPMV-B22-P....NEW
PMV-B16-P.....NEW
PMV-B16-V....NEW
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
P-Pilot
PMV-R22-F/H......NEW
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LSL P
LSP TMP
ø**
T1
ø**
ø**
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø**
T1
L
ø**
P Pilot
PLUG
ø0.6
P Pilot
P pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
T1
L
ø**
ø**
P pilot
Page 4 & 5, PMV16 & 22 Datasheets
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS
L
P
LSP TMP
ø**
T1
ø**
ø**
PLUG
ø0.6
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS P
LSP TMP
ø**
T1
ø**
ø**
L
ø0.6
PLUG
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
ø0.6
PLUG
MP
Pls. update these two schemes. T1 line was missing.
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
PMV-B22-F/H PMV-R22-F/H
PMV-B22-V PMV-R22-V PMV-B22-P PMV-R22-P
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 5/19 Edition: 24 04 3.0-30E
PRESSURE COMPENSATED LS PUMP
The PMV inlet plate type B/R22-V is used for pressure compensated
LS pumps (constant pressure networks).
The inlet plate is used to connect P and T, whereby the LS connection
is closed here.
The LS signal can be adjusted to up to 420 bar via the pressure relief.
SCHEME V
PMV - B00 - A - - - K8
A Anti-saturation and LS amplier (in combination with V or P inlet plate)
Portconnection
G Thread in BSP
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
ANTI-SATURATION,LSAMPLIFIERPMV-B00(OPTIONFORINLETPLATE)
OPTIONANTI-SATURATION,LSAMPLIFIER
The anti-saturation option is used for electrically and hydraulically
operated valves.
If insucient pump ow is provided to the valve block, then the an-
ti-saturation function reduces the feed pressure of the pilot circuit. This
enables the simultaneous and load pressure independent operation of
the individual functions.
The LS amplier option amplies the LS signal in the direction of the
pump and compensates for signal losses. This is useful if the LS pump
has its own internal pressure relief, which causes LS signal pressure
losses. This option can also be used for stability adjustments between
pump and valve block.
SCHEME B00-A
PMV-B22-F/H....NEW
PMV-B22-V.....NEW
PMV-B16-F/H....NEW
PMV-R22-V......
PMV-R22-P.....NEWPMV-B22-P....NEW
PMV-B16-P.....NEW
PMV-B16-V....NEW
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
P-Pilot
PMV-R22-F/H......NEW
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LSL P
LSP TMP
ø**
T1
ø**
ø**
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø**
T1
L
ø**
P Pilot
PLUG
ø0.6
P Pilot
P pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
T1
L
ø**
ø**
P pilot
Page 4 & 5, PMV16 & 22 Datasheets
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS
L
P
LSP TMP
ø**
T1
ø**
ø**
PLUG
ø0.6
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS P
LSP TMP
ø**
T1
ø**
ø**
L
ø0.6
PLUG
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
ø0.6
PLUG
MP
Pls. update these two schemes. T1 line was missing.
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
PMV-B22-V PMV-R22-V
PMV-B22-P PMV-B00-A
Page 5 / SYMBOL A
PMV-B00-A
PMV-B22-P-...
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
P pilot
T1
P
LS
LSamp
ø**
ø**
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
www.wandfluh.com Illustrations are not binding Data subject to change 6/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
OPTION ELECTRICAL-PROPORTIONAL PRESSURE SETTING
(P/I)
With this function, the maximum pressure of the entire block can be
adjusted electrically-proportionally.
This function is available in 12V DC and 24V DC.
Limiting current at 50°C 1320 mA at 12 VDC
660 mA at 24 VDC
OPTIONPUMPUNLOADING(O/C)
The pump unloading function can be used as an emergency stop
function, for example. The LS signal of all control sections to the tank
is unloaded. Both the "normally open"and the "normally closed" version
are available. Please note that the stand-by pressure or the pressure in
the pump line remains despite the function activation.
The 12VDC respectively 24VDC solenoids have an electrical power
of 20 watt.
SCHEMEO/C/P/I
I / P C / O
PMV - B00 - - - - - K8
Pumpunloadingandelectrical-proportionalpressurerelief
O Normally open
C Normally closed
P Electrical proportional pressure relief
I Inverse electrical-proportional pressure relief
Voltage
12 12 Volt DC
24 24 Volt DC
Electricalspecications
SD Connector socket DIN, EN175301-803 / ISO 4400
SG Connector socket Deutsch DT04 - 2P
Portconnection
G Thread in BSP
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
PUMPUNLOADINGPMV-B00(OPTIONTOINLETPLATE)
MAX.PRESSUREFORPMV-B00K8
p
max
= 350 bar
INSTALLED VALVES
Type Designation Data sheet no.
O Normally open -
C Normally closed 1.11-208B
P Electrical-proportional pressure relief 2.3-539
I Inverse electrical-proportional pressure
relief
2.3-548
(PMV-B16-P.....) SCHEME O / C / P / I
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
Page 6, PMV16 & 22 Datasheets
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
(PMV-B22-P.....) SCHEME O / C / P / I
LS
L
LS
L
LS
L
LS
L
LS
L
LS
L
LS
L
LS
L
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 7/19 Edition: 24 04 3.0-30E
CONTROL SECTION PMV-M22
CONTROL SECTION M22-A
The M22-A unit does not have a pressure compensator.
CONTROLSECTIONM22-B/C
The units M22-B / C are equipped with a pressure compensator.
The M22-C variant is additionally equipped with a non-return valve in
the supply line to the pressure compensator to ensure the pressure
independence of the individual control sections. The non-return function
prevents consumer oil from owing back into the pump channel.
NOTE!
M22-C ow decreased with 10%.
Max ow 350 l/min across control section C.
The pressure compensation of the pressure compensator can be se-
lected to increase or decrease the ow compared to the nominal value
of the spool. The delta p of the pressure compensator is adjustable via
an adjusting screw on the outside of the valve.
Tightening torque delta p adjusting screw: 10 Nm
SCHEME A
SCHEMEB/C
M22-B M22-C
By selecting a pressure compensator in the control section, the ow
rate is regulated individually and load-independently per function. Each
control section can be individually congured with a wide variety of
modules. The actuation functions "electrical", "hydraulical" and "manual”
can be added to the control section to guarantee high exibility of the
variants. A manual override function is also possible for the electrical
and hydraulical operating modes.
The complete PMV-22 control unit can be constructed from up to 10
dierent control sections.
PMV - M22 - - - - K8
Pressurecompensator
A Without pressure compensator
B With pressure compensator
C With pressure compensator and non-return valve function
S Spacer plate Width = 15,25 mm (1/4" of a section)
S1 Spacer plate Width = 30,50 mm (1/2" of a section)
Pressurecompensatorspring
Nominal volume ow rate Q
N
see spool kit PMV-S22
N No pressure compensator (for option A & S only)
S Standard ow spring (100 % ow) 800.3204
Spring/-kit (others on request)
L Low ow spring (68 % ow) 800.3206
H High ow spring (160 % ow) 800.3205
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS
T
T LS
b a
PAGE 7, SCHEME A
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS T
T LS
b a
PAGE 7, SCHEME B
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A
B
LS T
T
LS
b a
PAGE 7, SCHEME C
Rev Date Drawn Checked Description
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS
T
T LS
b a
PAGE 7, SCHEME A
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS T
T LS
b a
PAGE 7, SCHEME B
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A
B
LS T
T
LS
b a
PAGE 7, SCHEME C
Rev Date Drawn Checked Description
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
www.wandfluh.com Illustrations are not binding Data subject to change 8/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
ELECTRICAL-PROPORTIONAL PMV-P22 FOR CONTROL SECTION
ELECTRICAL-PROPORTIONAL
The electrically-proportionally actuated version uses an electrical
control module that controls the main spool of the control section via 2
proportional pressure reducing valves.
The pressure reducing valves are available in 12VDC and 24 VDC with
dierent connector versions.
The control module PMV-P22 can be used optionally in combination with
the spring cap PMV-D22 or the manual override PMV-L22.
The cap contains an adjustment screw for ow limitation.
Tightening torque of the fastening screws: 10 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
Limiting current at 50°C 1500 mA at 12 VDC
750 mA at 24 VDC
Solenoid resistance 4.72 Ω ±5% at 12 VDC
20.8 Ω ±5% at 24 VDC
SCHEME
PMV - P22 - - - K8
Voltage
12 12 Volt DC
24 24 Volt DC
Electricalspecications
SJ Connector socket AMP Junior Timer
SG Plug socket Deutsch DT04 - 2P
XA ATEX (IECEx, CCC, EAC) L15*
XU AUS Australia L15*
XM MA L15*
XC UC NEC 500 / NEC 505 L15*
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
* Other electrical specifications see data sheet 1.1-183
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS T
T LS
b a
PAGE 8, SCHEME P22
PAGE 9, SCHEME H22
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
PAGE 11, SCHEME L22 & A22
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS
T
T
LS
Rev Date Drawn Checked Description
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 9/19 Edition: 24 04 3.0-30E
PMV - H22 - - - K8
Portconnection
G Thread in BSP
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
HYDRAULICAL PMV-H22 FOR CONTROL SECTION
HYDRAULICAL
In the hydraulically actuated version, instead of the electrical-proportional
control module, a hydraulic control module is used, which contains ports
(A, B) for the hydraulic joysticks.
The port dimension is designed in ¼"BSP.
The pilot pressure range of the hydraulic joysticks used should be 6
to 22 bar.
The control module PMV-H22 can be used optionally in combination with
the spring cap PMV-D22 or the manual override PMV-L22.
The cap contains an adjustment screw for ow limitation.
Tightening torque of the fastening screws: 10 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
SCHEME
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
www.wandfluh.com Illustrations are not binding Data subject to change 10/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
SPRING CAP PMV-D22 FOR CONTROL SECTION
MANUAL PMV-L22 FOR CONTROL SECTION
SPRING CAP D22
The spring cap D22 is used for the electrical and hydraulical operating
form. The cap is used to hold the spring assembly and contains an
adjustment screw for ow limitation.
Tightening torque of the fastening screws: 10 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
MANUAL L22
The manual cap L22 is used for the manually operated function only or
the manual override function.
The cap is used to hold the spring assembly and contains an adjustment
screw for ow limitation.
Tightening torque of the fastening screws: 10 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
Max. lever force: 35 N
Centre position lever: Standard horizontal,
can optionally be mounted rotated by 30° in both directions.
Lever stroke range for full deection: +/- 30°
PMV - D22 - - K8
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
PMV - L22 - - K8
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 11/19 Edition: 24 04 3.0-30E
MANUALLY OPERATED PMV-A22 FOR CONTROL SECTION
MANUALLY ACTUATED
For fully manual control sections, the end cap A22 is used in combination
with the manual cap L22.
The cap contains an adjustment screw for ow limitation.
Tightening torque of the fastening screws: 10 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
SCHEME
PMV - A22 - - K8
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS T
T LS
b a
PAGE 8, SCHEME P22
PAGE 9, SCHEME H22
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
PAGE 11, SCHEME L22 & A22
P Pilot
L
LS
P
T1
A B LSBLSA
PT T
A B
LS
T
T
LS
Rev Date Drawn Checked Description
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
www.wandfluh.com Illustrations are not binding Data subject to change 12/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
SPOOL PMV-S22
SYMBOL
PMV - S22 - - - -
SymbolSpool
ACB
ADB
Ratio
1 1:1
2 2:1 (high ow in A)
NominalvolumeowrateQ
N
250 250 l/min
Springassembly
H Manual control only (A22 with L22)
E Electrical / hydraulical control (P22 or H22 with D22)
O Electrical / hydraulical control – manual override (P22 or H22 with L22)
PT
A B
T
LSA LSB
PT
A B
T
LSA LSB
Spool with closed centre position Spool with open centre position
A / B 20 % open to the tank
ACB ADB
The various spool sets consist of spool and spring assembly and can
be mounted in any variation in the honed bore of the control section
due to the high production accuracy.
In order to cover the entire volume ow range, there are various spools
with corresponding control edges.
Spools with a ow ratio of 1:1, but also spools with a ow ratio of 2:1
can be congured for the corresponding cylinder applications.
The PMV programme provides a wide range of spool types. The most
common spools are available with closed or open centre position, but
special shapes are also available. Flexibility is further increased with the
choice of pressure compensator delta p setting in the control section to
precisely set the required ow rate.
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 13/19 Edition: 24 04 3.0-30E
CONNECTION PLATE PMV-C22
PMV - C22 - - - - - - K8
Type
N A/B port only
H A/B port & LS relief
C A/B port & LS relief & optional cartridge
T Twin plate, port connection F/F1 only
A Adapter plate in combination with F1 Twin plate
Max.settingLSpressurerelief
N Without (only N & T with F1 plate)
1 100 bar (not optional for N & T with F1)
4 420 bar (not optional for N & T with F1)
CartridgeoptionssideA
N No options (If C or T no cartridge mounted)
T Shock suction function For type C & T (F)
A Pressure relief in user port, 50-420 bar For type C & T (F)
S Suction function For type C & T (F)
CartridgeoptionssideB
N No options (If C or T no cartridge mounted)
T Shock suction function For type C & T (F)
A Pressure relief in user port, 50-420 bar For type C & T (F)
S Suction function For type C & T (F)
Portconnection
N Connection surface (Adapter plate)
G Thread in BSP
S Thread in SAE-ORB
F Flange SAE 1", code 62
F1 Flange SAE 1-1/2", code 62
Sealtype
NN No seals (N plate only)
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
www.wandfluh.com Illustrations are not binding Data subject to change 14/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
CONNECTION PLATE C22-C
The connection plate type C22-C is an extended design.
In addition to the LS pressure relief valves, this plate can be extended
with additional cartridges for various functions. Possible variants of
built-in cartridges are the suction function (S), the pressure relief func-
tion (A) and the shock suction function (T). The cartridges can be used
independently on the A and B sides.
These additional valves in A and B act directly on the working port. This
is in contrast to the LS pressure limitations, which act on the LS signal.
SCHEME C
C-TT
C-AA
C-SS
T-TT
CONNECTION PLATE C22-N
The basic connecting plate type C22-N has only the ports A and B.
CONNECTION PLATE C22-H
LS pressure relief valves are integrated in the connection plate type
C22-H on the A and B sides.
SCHEME N
SCHEME H
SURFACE TREATMENTS
Cartridges for PMV-C22-C are zinc coated.
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
CONNECTION PLATE C22-T
TwinplatewithSAE1"connection
The connection plate type C22-T is an extended design called Twin plate.
It combines the ow from two sections.
In addition to the LS pressure relief valves, this plate can be extended
with additional cartridges for various functions. Possible variants of
built-in cartridges are the suction function (S), the pressure relief func-
tion (A) and the shock suction function (T). The cartridges can be used
independently on the A and B sides.
These additional valves in A and B act directly on the working port. This
is in contrast to the LS pressure limitations, which act on the LS signal.
TwinplatewithSAE1-1/2"connection
For SAE 1-1/2" connection an adapter plate is required where the LS
pressure relief valves are mounted (2 in the A ports and 2 in the B ports).
The Twin plate with SAE 1-1/2" connections is mounted on the Adapter
plate. These have no additional valve functions integrated.
SCHEME T
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
A
SAE 1-1/2"
B
SAE 1-1/2"
Ya Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
T-F1 WITH A (ADAPTER PLATE)
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 15/19 Edition: 24 04 3.0-30E
END PLATE PMV-E22
SMALL END PLATE E22-A
The PMV end plate type E22-A only contains the LS pressure relief of
the shuttle valve cascade.
SCHEME A
WIDE END PLATE E22-B
The PMV end plate type E22-B includes an extra P and T port in addition
to the LS pressure relief of the shuttle valve cascade.
WIDE END PLATE E22-C
The PMV end plate type E22-C includes an extra P and T port.
In addition, the LS signal of a downstream valve unit can be connected to
the upstream valve unit via the Z port (series connection of two blocks).
SCHEME B
SCHEME C
PMV - E22 - - - - K8
Plateversion
A Small end plate without ports
B With additional P2 and T2port
C With Z port, with additional P2 and T2 port
Portconnection
G Thread in BSP
S Thread in SAE-ORB
N No ports (A plate only)
Sealtype
NN No seals (A plate only)
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
Page 15 => SYMBOL B
Page 15 => SYMBOL A
Page 15 => SYMBOL C
T2
P
Z
T2
P
Z
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 15 => SYMBOL B
Page 15 => SYMBOL A
Page 15 => SYMBOL C
T2
P
Z
T2
P
Z
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 15 => SYMBOL B
Page 15 => SYMBOL A
Page 15 => SYMBOL C
T2
P
Z
T2
P
Z
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
NOTE!
Using the reduction inlet plate PMV-R22, it is necessary
to have on both sides the (wide) endplate.
PMV-E22-B/C (size 22 side) and PMV-E16-B/C (size16
side)
www.wandfluh.com Illustrations are not binding Data subject to change 16/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
Tierods PMV - T22 -
S01 Tie rod kit small, end plate A, 1 section
S02 Tie rod kit small, end plate A, 2 sections
S03 Tie rod kit small, end plate A, 3 sections
S04 Tie rod kit small, end plate A, 4 sections
S05 Tie rod kit small, end plate A, 5 sections
S06 Tie rod kit small, end plate A, 6 sections
S07 Tie rod kit small, end plate A, 7 sections
S08 Tie rod kit small, end plate A, 8 sections
S09 Tie rod kit small, end plate A, 9 sections
S10 Tie rod kit small, end plate A, 10 sections
W01 Tie rod kit wide, end plate B/C, 1 section
W02 Tie rod kit wide, end plate B/C, 2 sections
W03 Tie rod kit wide, end plate B/C, 3 sections
W04 Tie rod kit wide, end plate B/C, 4 sections
W05 Tie rod kit wide, end plate B/C, 5 sections
W06 Tie rod kit wide, end plate B/C, 6 sections
W07 Tie rod kit wide, end plate B/C, 7 sections
W08 Tie rod kit wide, end plate B/C, 8 sections
W09 Tie rod kit wide, end plate B/C, 9 sections
W10 Tie rod kit wide, end plate B/C, 10 sections
TIE RODS
For the assembly of complete PMV-22 control blocks, 2 dierent tie
rod kits are available, which are used depending on the type of end
plate used.
The tie rod kits each consist of 3 pcs. tie rods and M10 nuts with plastic
caps.
The tie rods are in Cr-steel material and the M10 nuts are Zinc-nickel
coated
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 17/19 Edition: 24 04 3.0-30E
Q = f (l) Volumeow-signal-characteristics
Spool types ACB, ADB
I [mA]
500
1000
600
1200
400
800
300
600
200
400
0
0
24 VDC
12 VDC
100
200
700
1400
K4288
Q [l/min]
I [mA]
450
400
350
300
250
200
150
100
50
0
Q = 400 l/min
Q = 250 l/min
Q = 170 l/min
PERFORMANCE SPECIFICATIONS
Oil viscosity = 30 mm2/s
Δp = f (Q) Pressuredropvolumeowcharacteristic
Recirculation curve 3-way pressure compensator
Inlet plate type B22-F/H
K4287
∆p [bar] P → T
Q [l/min]
5004003002000 100 600 700
35
30
25
20
15
10
5
0
B22-H
B22-F
Q = f (p) Volumeow-pressure-characteristics
Pressure compensator type M22-B
K4289
Q [l/min]
p [bar]
3002001000 420
375
300
225
150
75
0
Q = 350 l/min
Q = 300 l/min
Q = 250 l/min
Q = 200 l/min
Q = 130 l/min
Q = f (dp) Volumeow-pressure-characteristics
Control section without pressure compensator
K4290
Q [l/min]
∆p [bar]
504030200 10
640
540
440
340
240
140
40
www.wandfluh.com Illustrations are not binding Data subject to change 18/19 Edition: 24 04 3.0-30E
Proportional Mobile Valve PMV-22
DIMENSIONS
Dimension drawing
E
F
D
Radiuses,
m
H
Linear dimensions
G
Page 1 of 1C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV -22\PMV-22 Komplette Ventile\0304409
P/N:
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6 >30-120
Weight
±0.5
±0.1
+0.4
±0.3
>6-30
±0.2
±0.1
±1
±0.2
Ra 3.2
to third parties without permission in written form.
C
B
A
m
7VIAL
Violation is illegal and will be legally prosecuted.
M 1:2
0304409
Format
68.220 kg
-0.3
1413
H
A0
PMV-22
ISO 14405
erstellt
Surface finish
ECNRev.
Edges acc. ISO 13715
Replacement for:
00
Project number:
Doc.-No.
ECN-Description
Name
H
Concentricity, axial runout
Date
27.07.2022
Checked
Nominal dimension
H
Envelope requirement acc.to
Released
Drawn
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0304406 / Configuration 001
205
181
31
163.6
81
10
M
1
0
x
1
5
(
4
x
)
3
0
°
183.6 103.1 94
3
0
°
1
6
0
61 61
200
389
61
45
60 85 (R22; 90)
M
1
0
x
1
5
61
10
49
52.5
123.3
34
125.8
66.5 61
4
11
12
13
14
15
16
1
2
5
6
7
8
9
10
3
17
15
M
1
0
x
1
5
M
1
0
x
1
5
M
1
0
x1
5
153.6
31.6
151.6
10
25
M
1
0
x1
5
E
F
D
Radiuses,
m
H
Linear dimensions
G
Page 1 of 1C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV -22\PMV-22 Komplette Ventile\0304409
P/N:
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6 >30-120
Weight
±0.5
±0.1
+0.4
±0.3
>6-30
±0.2
±0.1
±1
±0.2
Ra 3.2
to third parties without permission in written form.
C
B
A
m
7VIAL
Violation is illegal and will be legally prosecuted.
M 1:2
0304409
Format
68.220 kg
-0.3
1413
H
A0
PMV-22
ISO 14405
erstellt
Surface finish
ECNRev.
Edges acc. ISO 13715
Replacement for:
00
Project number:
Doc.-No.
ECN-Description
Name
H
Concentricity, axial runout
Date
27.07.2022
Checked
Nominal dimension
H
Envelope requirement acc.to
Released
Drawn
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0304406 / Configuration 001
205
181
31
163.6
81
10
M
1
0
x
1
5
(
4
x
)
3
0
°
183.6 103.1 94
3
0
°
1
6
0
61 61
200
389
61
45
60 85 (R22; 90)
M
1
0
x
1
5
61
10
49
52.5
123.3
34
125.8
66.5 61
4
11
12
13
14
15
16
1
2
5
6
7
8
9
10
3
17
15
M
1
0
x
1
5
M
1
0
x
1
5
M
1
0
x1
5
153.6
31.6
151.6
10
25
M
1
0
x1
5
E
F
D
Radiuses,
m
H
Linear dimensions
G
Page 1 of 1C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV -22\PMV-22 Komplette Ventile\0304409
P/N:
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6 >30-120
Weight
±0.5
±0.1
+0.4
±0.3
>6-30
±0.2
±0.1
±1
±0.2
Ra 3.2
to third parties without permission in written form.
C
B
A
m
7VIAL
Violation is illegal and will be legally prosecuted.
M 1:2
0304409
Format
68.220 kg
-0.3
1413
H
A0
PMV-22
ISO 14405
erstellt
Surface finish
ECNRev.
Edges acc. ISO 13715
Replacement for:
00
Project number:
Doc.-No.
ECN-Description
Name
H
Concentricity, axial runout
Date
27.07.2022
Checked
Nominal dimension
H
Envelope requirement acc.to
Released
Drawn
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0304406 / Configuration 001
205
181
31
163.6
81
10
M
1
0
x
1
5
(
4
x
)
3
0
°
183.6 103.1 94
3
0
°
1
6
0
61 61
200
389
61
45
60 85 (R22; 90)
M
1
0
x
1
5
61
10
49
52.5
123.3
34
125.8
66.5 61
4
11
12
13
14
15
16
1
2
5
6
7
8
9
10
3
17
15
M
1
0
x
1
5
M
1
0
x
1
5
M
1
0
x1
5
153.6
31.6
151.6
10
25
M
1
0
x1
5
E
F
D
Radiuses,
m
H
Linear dimensions
G
Page 1 of 1C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV -22\PMV-22 Komplette Ventile\0304409
P/N:
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6 >30-120
Weight
±0.5
±0.1
+0.4
±0.3
>6-30
±0.2
±0.1
±1
±0.2
Ra 3.2
to third parties without permission in written form.
C
B
A
m
7VIAL
Violation is illegal and will be legally prosecuted.
M 1:2
0304409
Format
68.220 kg
-0.3
1413
H
A0
PMV-22
ISO 14405
erstellt
Surface finish
ECNRev.
Edges acc. ISO 13715
Replacement for:
00
Project number:
Doc.-No.
ECN-Description
Name
H
Concentricity, axial runout
Date
27.07.2022
Checked
Nominal dimension
H
Envelope requirement acc.to
Released
Drawn
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0304406 / Configuration 001
205
181
31
163.6
81
10
M
1
0
x
1
5
(
4
x
)
3
0
°
183.6 103.1 94
3
0
°
1
6
0
61 61
200
389
61
45
60 85 (R22; 90)
M
1
0
x
1
5
61
10
49
52.5
123.3
34
125.8
66.5 61
4
11
12
13
14
15
16
1
2
5
6
7
8
9
10
3
17
15
M
1
0
x
1
5
M
1
0
x
1
5
M
1
0
x1
5
153.6
31.6
151.6
10
25
M
1
0
x1
5
E
F
D
Radiuses,
m
H
Linear dimensions
G
Page 1 of 1C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV -22\PMV-22 Komplette Ventile\0304409
P/N:
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6 >30-120
Weight
±0.5
±0.1
+0.4
±0.3
>6-30
±0.2
±0.1
±1
±0.2
Ra 3.2
to third parties without permission in written form.
C
B
A
m
7VIAL
Violation is illegal and will be legally prosecuted.
M 1:2
0304409
Format
68.220 kg
-0.3
1413
H
A0
PMV-22
ISO 14405
erstellt
Surface finish
ECNRev.
Edges acc. ISO 13715
Replacement for:
00
Project number:
Doc.-No.
ECN-Description
Name
H
Concentricity, axial runout
Date
27.07.2022
Checked
Nominal dimension
H
Envelope requirement acc.to
Released
Drawn
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0304406 / Configuration 001
205
181
31
163.6
81
10
M
1
0
x
1
5
(
4
x
)
3
0
°
183.6 103.1 94
3
0
°
1
6
0
61 61
200
389
61
45
60 85 (R22; 90)
M
1
0
x
1
5
61
10
49
52.5
123.3
34
125.8
66.5 61
4
11
12
13
14
15
16
1
2
5
6
7
8
9
10
3
17
15
M
1
0
x
1
5
M
1
0
x
1
5
M
1
0
x1
5
153.6
31.6
151.6
10
25
M
1
0
x1
5
E
F
D
Radiuses,
m
H
Linear dimensions
G
Page 1 of 1C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV -22\PMV-22 Komplette Ventile\0304409
P/N:
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6 >30-120
Weight
±0.5
±0.1
+0.4
±0.3
>6-30
±0.2
±0.1
±1
±0.2
Ra 3.2
to third parties without permission in written form.
C
B
A
m
7VIAL
Violation is illegal and will be legally prosecuted.
M 1:2
0304409
Format
68.220 kg
-0.3
1413
H
A0
PMV-22
ISO 14405
erstellt
Surface finish
ECNRev.
Edges acc. ISO 13715
Replacement for:
00
Project number:
Doc.-No.
ECN-Description
Name
H
Concentricity, axial runout
Date
27.07.2022
Checked
Nominal dimension
H
Envelope requirement acc.to
Released
Drawn
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0304406 / Configuration 001
205
181
31
163.6
81
10
M
1
0
x
1
5
(
4
x
)
3
0
°
183.6 103.1 94
3
0
°
1
6
0
61 61
200
389
61
45
60 85 (R22; 90)
M
1
0
x
1
5
61
10
49
52.5
123.3
34
125.8
66.5 61
4
11
12
13
14
15
16
1
2
5
6
7
8
9
10
3
17
15
M
1
0
x
1
5
M
1
0
x
1
5
M
1
0
x1
5
153.6
31.6
151.6
10
25
M
1
0
x1
5
Proportional Mobile Valve PMV-22
www.wandfluh.com Illustrations are not binding Data subject to change 19/19 Edition: 24 04 3.0-30E
HYDRAULIC PORT
Port BSP SAE ORB
Port P G 1 1/4“ 20
Port T G 1 1/2“ 24
Port A, B G 1 1/4“ 20
Port LS G 1/4“ 6
Port L (Drain) G 1/4“ 6
Port Ya, Yb G 1/4“ 6
Port Z G 1/4“ 6
WEIGHTS PER PMV MODULE
PMV-B22-F/H 11,7 kg
PMV-B22-V 10,9 kg
PMV-M22 6,8 kg
PMV-P22 1,4 kg
PMV-P22-XA 4,2 kg
PMV-H22 0,8 kg
PMV-D22 0,5 kg
PMV-L22 1,1 kg
PMV-A22 0,6 kg
PMV-S22 0,4 kg
PMV-C22-N 2,2 kg
PMV-C22-H 2,9 kg
PMV-C22-C 6,2 kg
PMV-C22-T 11,0 kg
PMV-E22-A 2,7 kg
PMV-E22-B 7,2 kg
PMV-R22 12,7 kg
WEIGHTSPERTIERODKIT
PMV-T22-W01 0,3 kg
PMV-T22-W02 0,4 kg
PMV-T22-W03 0,5 kg
PMV-T22-W04 0,6 kg
PMV-T22-W05 0,8 kg
PMV-T22-W06 0,9 kg
PMV-T22-W07 1,0 kg
PMV-T22-W08 1,1 kg
PMV-T22-W09 1,2 kg
PMV-T22-W10 1,3 kg
WEIGHTSPERTIERODKIT
PMV-T22-S01 0,2 kg
PMV-T22-S02 0,3 kg
PMV-T22-S03 0,5 kg
PMV-T22-S04 0,6 kg
PMV-T22-S05 0,7 kg
PMV-T22-S06 0,8 kg
PMV-T22-S07 0,9 kg
PMV-T22-S08 1,0 kg
PMV-T22-S09 1,1 kg
PMV-T22-S10 1,2 kg
WEIGHTS PER PMV MODULE
PMV-B00-A-G 1,0 kg
PMV-B00-I-G 1,4 kg
PMV-B00-P-G 1,4 kg
PMV-B00-O-G 0,8 kg
PMV-B00-C-G 0,7 kg
ASSEMBLY INSTRUCTIONS
Type of mounting Control unit in sandwich construction
with threaded connection.
Mounting holes on the inlet and end
plate M10 x 12
Mounting position any
Tightening torque
Tie rods
M = 46 Nm
Socket Tool 17 mm
ASSEMBLY OF THE CONTROL UNIT
Various M10x12 mounting threads are available for the assembly of
the control unit:
Inlet plate:
PMV-B22: 6 x mounting thread M10x12
End plate:
PMV-E22: 3 x mounting thread M10x12