Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 1/19 Edition: 24 04 3.0-20E
APPLICATION
The areas of application oer great diversity. PMV are used where
compact installation dimensions are required and a function requires
sensitively controlled.
Typical applications are cylinder and motor controls for all handling
functions as in loading cranes, telescopic handlers, aerial platforms,
municipal vehicles, construction machinery, drilling equipment, agricul-
tural and forestry machinery, oshore applications, underground mining.
DESCRIPTION
The PMV concept is constructed to oer a high level of modularity. It
allows a conguration of individual modules, which are available as
pre-assembled units with their own type code. Modications, to and
between them, can also be carried out quickly in the eld.
Due to the modular design, special solutions can also be created in a
exible manner. For example, counterbalance valves integrated in the
connection plate or operated non-return valves can be integrated. By
means of the 2-way pressure compensator, the ow can be controlled
Independent from the load.
• Veryexiblycombinableandloadindependent
• Pre-compensatedandload-sensing
• Highcorrosionprotection,K8(Zn/Ni)
• Stainlesssteeladjustingscrews
• Q
max
=180l/min(withoutcompensator200l/min)
• p
max
=420bar
PMV-16
OVERVIEW PMV
OVERVIEW PMV
PMV-P16 (Electrical-pro-
portional)
PMV-T16 (tie rod)
PMV-H16 (Hydraulic)
PMV-A16 (end cap)
PMV-D16 (spring cap)PMV-B00 Option
(pump unloading)
PMV-B00-A option (an-
ti-saturation, LS amplifi er)
PMV-L16 (Manual)PMV-S16 (spool)
PMV-B16 (inlet plate)
PMV-M16 (control
section)
PMV-C16 (connection
plate)
PMV-E16 (end plate)
P
roportional Mobile Valves
A-SIDE B-SIDE
www.wandfluh.com Illustrations are not binding Data subject to change 2/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
OVERVIEW PMV EXAMPLE UNIT
1: End plate
2: Control section
3: delta p setting
4: Spring cap with manual actuation
5: Spring cap
6: Stroke limitation
7: Inlet plate
8: Input pressure limitation
9: LS relief valve A
10: LS relief valve B
11: Connection plate
12: Proportional pressure reducing valve B
13: Proportional pressure reducing valve A
14: Connection plate with LS pressure reliefs
15: End cap
P Pilot
L
P
L
P
LS
LS
P
T1
T1
P
LS
*
LS
ø0.6
Plug
ø**
T1
ø**
7
8
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
2
3
5
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
13
12
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
6
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T T LS
15
4
T2
P
Z
1
A B
11
A BYa Yb
14
10
9
A BYa Yb
14
A B
11
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
1
6
0
Page 1 of 2C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
H
to third parties without permission in written form.
-0.3
Format
Nominal dimension
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6 >6-30 >30-120
±0.1 ±0.1 ±0.2
±0.3
±0.2 ±0.5 ±1
+0.4
Ra 3.2
0289340
Linear dimensions
G
F
E
H
H
00
A0
m
M 1:2
Radiuses,
34.687 kg
D
C
Edges acc. ISO 13715
ISO 14405
erstellt
Surface finish
ECNRev.
P/N:
Doc.-No.
Replacement for:
Replaced by:
ECN-DescriptionNameDate
7VIAL
08.06.2021
Checked
Released
Drawn
Weight
Revision
H
m
Concentricity, axial runout
Violation is illegal and will be legally prosecuted.
Envelope requirement acc.to
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
B
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
73.5
312
56 56 56 56 14.5
121
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
14
4
11
7
3
2
8
5
13
12
9
10
6
15
3
0
°
3
0
°
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 3/19 Edition: 24 04 3.0-20E
ELECTRICAL SPECIFICATIONS
Nominal voltage 12 VDC or 24 VDC
Type of protection Connection version D: IP65
Connection version J: IP66
Connection version G: IP67 and IP69K
Connection Connector socket D: DIN, EN175301-
803 / ISO 4400
Connector socket J: AMP Junior Timer
Connector socket G: Deutsch DT04 – 2P
Relative duty factor 100 % DF
Dither frequency for
proportional solenoids
(recommended)
100 Hz
GENERAL SPECIFICATIONS
Designation Proportional spool valve
Construction type Sectional design pilot operated
Mounting type Inline mounting
Any mounting position
Dimension Nominal size 16
Number of control
sections
Max. 12
Temperature range
environment
-30…+70 °C
MTTFd 150 years
ACTUATION
Possible modes of
operation
• Electrically pilot operated (12V/24V)
• Hydraulically pilot operated (6-22 bar)
• Manual
Manual override (lever) optional combined with electric and hydraulic
actuation.
SURFACETREATMENTSK8
• Most external parts are zinc-nickel coated (K8).
• The xing screws are zinc coated.
• Adjusting screws are in stainless steel.
SEALING MATERIALS
HNBR as standard, FKM (Viton) as option
HYDRAULIC SPECIFICATIONS
Operating pressure P,
A/B
p
max
= 420 bar
Tank pressure p
Tmax
= 35 bar
Maximum volume ow
Q
max
Port P1 or P2: 180 l/min
Port P1 and P2: 280 l/min
Port A/B: 180 l/min (with compensator)
Pressure setting range 50…420 bar
Hysteresis
Hysteresis EHA
≤ 3 % at optimal dither signal
≤ 1 % at optimal dither signal
Fluid Mineral-based or synthetic hydraulic uid
with lubricating properties
Viscosity range 12 mm
2
/s…320 mm
2
/s
Temperature range uid -30…+80 °C (HNBR)
-15…+80 °C (Viton)
Contamination ecency Class 18 / 16 / 13 ISO 4406
Filtration Recommended ltration grade beta
6...10 >= 75
EHA GENERAL SPECIFICATION
Material of housing: Die-cast aluminum AlSi10Mg
Surface treatment: Anodizing EV1
Salt spray test: 360 hours IEC 60068-2-11 part 2 Ka
www.wandfluh.com Illustrations are not binding Data subject to change 4/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
FIXED DISPLACEMENT PUMP
The PMV inlet plate type B16-F/H is used for xed displacement pumps.
This inlet plate includes a 3-way pressure compensator for the recircu-
lation function, as well as a maximum pressure setting. The adjustment
range of the maximum pressure setting is 14 to 420 bar.
The inlet plate type B16-F is suitable for ows up to 100 l/min with
one control section. For higher ow rates, the inlet plate type B16-H
is required.
If no control section is actuated, the pump ow recirculates to the tank
without pressure.
When one or more control sections are actuated, the highest load
pressure signal is fed back to the 3-way pressure compensator, pres-
surising the pump line.
VARIABLEPUMP(LSPUMP)
The PMV inlet plate type B16-V/P is used for load sensing pumps (LS
pumps).
The PMV inlet plate of type B16-V has the ports P, T and the LS signal.
The LS signal can be adjusted up to 420 bar via the pressure setting.
The type B16-P inlet plate also has a maximum pressure setting in P
to provide additional protection for the system.
SCHEMEF/H
SCHEMEV/P
INLET PLATE PMV-B16
B16-V B16-P
PMV - B16 - - - - - K8
Plateversion
F For xed displacement pump
H For xed displacement pump high ow
V For LS pump
P For LS pump with main relief valve in P
Max.pressuremainrelief
1 p
max
100 bar
4 p
max
420 bar
Portconnection
G Thread in BSP
S Thread in SAE-ORB
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
PMV-B22-F/H....NEW
PMV-B22-V.....NEW
PMV-B16-F/H....NEW
PMV-R22-V......
PMV-R22-P.....NEWPMV-B22-P....NEW
PMV-B16-P.....NEW
PMV-B16-V....NEW
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
P-Pilot
PMV-R22-F/H......NEW
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LSL P
LSP TMP
ø**
T1
ø**
ø**
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø**
T1
L
ø**
P Pilot
PLUG
ø0.6
P Pilot
P pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
T1
L
ø**
ø**
P pilot
Page 4 & 5, PMV16 & 22 Datasheets
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS
L
P
LSP TMP
ø**
T1
ø**
ø**
PLUG
ø0.6
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS P
LSP TMP
ø**
T1
ø**
ø**
L
ø0.6
PLUG
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
ø0.6
PLUG
MP
Pls. update these two schemes. T1 line was missing.
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
PMV-B22-F/H....NEW
PMV-B22-V.....NEW
PMV-B16-F/H....NEW
PMV-R22-V......
PMV-R22-P.....NEWPMV-B22-P....NEW
PMV-B16-P.....NEW
PMV-B16-V....NEW
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
P-Pilot
PMV-R22-F/H......NEW
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LSL P
LSP TMP
ø**
T1
ø**
ø**
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø**
T1
L
ø**
P Pilot
PLUG
ø0.6
P Pilot
P pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
T1
L
ø**
ø**
P pilot
Page 4 & 5, PMV16 & 22 Datasheets
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS
L
P
LSP TMP
ø**
T1
ø**
ø**
PLUG
ø0.6
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS P
LSP TMP
ø**
T1
ø**
ø**
L
ø0.6
PLUG
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
ø0.6
PLUG
MP
Pls. update these two schemes. T1 line was missing.
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
PMV-B22-F/H....NEW
PMV-B22-V.....NEW
PMV-B16-F/H....NEW
PMV-R22-V......
PMV-R22-P.....NEWPMV-B22-P....NEW
PMV-B16-P.....NEW
PMV-B16-V....NEW
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
P-Pilot
PMV-R22-F/H......NEW
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LSL P
LSP TMP
ø**
T1
ø**
ø**
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
ø**
T1
L
ø**
P Pilot
PLUG
ø0.6
P Pilot
P pilot
L
P
LS
LS
P
T1
T1
P
LS
*
LS
MP
T1
L
ø**
ø**
P pilot
Page 4 & 5, PMV16 & 22 Datasheets
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS
L
P
LSP TMP
ø**
T1
ø**
ø**
PLUG
ø0.6
P pilot
L
P pilot
L
LS
P
T1
T1
P
LS
LS
LS P
LSP TMP
ø**
T1
ø**
ø**
L
ø0.6
PLUG
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
ø0.6
PLUG
MP
Pls. update these two schemes. T1 line was missing.
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 5/19 Edition: 24 04 3.0-20E
PRESSURE COMPENSATED LS PUMP
The PMV inlet plate type B16-V is used for pressure compensated LS
pumps (constant pressure networks).
The inlet plate is used to connect P and T, whereby the LS connection
is closed here.
The LS signal can be adjusted to up to 420 bar via the pressure relief.
SCHEME V
PMV
-
B00
-
A
- - -
K8
A Anti-saturation and LS amplier (in combination with V or P inlet plate)
Portconnection
G Thread in BSP
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
ANTI-SATURATION,LSAMPLIFIERPMV-B00(OPTIONFORINLETPLATE)
OPTIONANTI-SATURATION,LSAMPLIFIER
The anti-saturation option is used for electrically and hydraulically
operated valves.
If insucient pump ow is provided to the valve block, then the an-
ti-saturation function reduces the feed pressure of the pilot circuit. This
enables the simultaneous and load pressure independent operation of
the individual functions.
The LS amplier option amplies the LS signal in the direction of the
pump and compensates for signal losses. This is useful if the LS pump
has its own internal pressure relief, which causes LS signal pressure
losses. This option can also be used for stability adjustments between
pump and valve block.
SCHEME B00-A
Page 4 / Scheme F/H
P Pilot
L
P
L
P
LS
LS
P
T1
T1
P
LS
*
LS
ø0.6
Plug
ø**
T1
ø**
Page 4 / Scheme B16-P
Page 4 / Scheme B16-V
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
P Pilot
L
P
L
P
LS
LS
P
T1
T1
P
LS
*
LS
ø0.6
Plug
ø**
T1
ø**
Page 5 / Scheme V
P Pilot
P
L
P
LS
LS
P
T1
T1
P
LS
*
LSL
T1
ø**
ø**
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 5 / SYMBOL A
Page 6 / SYMBOL O / C
Page 6 / SYMBOL O / C / P / I
Page 6 / SYMBOL P / I
PMV-B00-A
PMV-B16-P-...
P Pilot
L
P
L
P
LS
LS
P
T1
T1
P
LS
*
LS
ø0.6
Plug
ø**
T1
ø**
P pilot
T1
P
LS
LSamp
ø**
ø**
P Pilot
L
P
L
P
LS
LS
P
T1
T1
P
LS
*
LS
ø0.6
Plug
ø**
T1
ø**
LS
L
LS
L
LS
L
LS
L
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
PMV-B00-A PMV-B16-P-...
www.wandfluh.com Illustrations are not binding Data subject to change 6/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
OPTION ELECTRICAL-PROPORTIONAL PRESSURE SETTING
(P/I)
With this function, the maximum pressure of the entire block can be
adjusted electrically-proportionally.
This function is available in 12V DC and 24V DC.
Limiting current at 50°C 1320 mA at 12 VDC
660 mA at 24 VDC
OPTIONPUMPUNLOADING(O/C)
The pump unloading function can be used as an emergency stop
function, for example. The LS signal of all control sections to the tank
is unloaded. Both the "normally open"and the "normally closed" version
are available. Please note that the stand-by pressure or the pressure in
the pump line remains despite the function activation.
The 12VDC respectively 24VDC solenoids have an electrical power
of 20 watt.
PMV - B00 - - - - - K8
Pumpunloadingandelectrical-proportionalpressurerelief
O Normally open
C Normally closed
P Electrical proportional pressure relief
I Inverse electrical-proportional pressure relief
Voltage
12 12 Volt DC
24 24 Volt DC
Electricalspecications
SD Connector socket DIN, EN175301-803 / ISO 4400
SG Connector socket Deutsch DT04 - 2P
Portconnection
G Thread in BSP
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
PUMPUNLOADINGPMV-B00(OPTIONTOINLETPLATE)
MAX.PRESSUREFORPMV-B00
p
max
= 350 bar
INSTALLED VALVES
Type Designation Data sheet no.
O Normally open -
C Normally closed 1.11-208B
P Electrical-proportional pressure relief 2.3-539
I Inverse electrical-proportional pressure
relief
2.3-548
SCHEMEO/C/P/I
O / C P / I
(PMV-B16-P.....) SCHEME O / C / P / I
P Pilot
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
MP
ø**
T1
L
ø**
P Pilot
ø0.6
PLUG
Page 6, PMV16 & 22 Datasheets
P Pilot
L
P Pilot
L
P
LS
LS
P
T1
T1
P
LS
LS
ø**
T1
ø**
P Pilot
PLUG
ø0.6
MP
(PMV-B22-P.....) SCHEME O / C / P / I
LS
L
LS
L
LS
L
LS
L
LS
L
LS
L
LS
L
LS
L
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 7/19 Edition: 24 04 3.0-20E
CONTROL SECTION PMV-M16
CONTROL SECTION M16-A
The M16-A unit does not have a pressure compensator.
200 % ow of nominal ow rate QN.
CONTROLSECTIONM16-B/C
The units M16-B / C are equipped with a pressure compensator.
The M16-C variant is additionally equipped with a non-return valve in
the supply line to the pressure compensator to ensure the pressure
independence of the individual control sections. The non-return function
prevents consumer oil from owing back into the pump channel.
NOTE!
Max ow 100 l/min across control section M16-C.
The pressure compensation of the pressure compensator can be se-
lected to increase or decrease the ow compared to the nominal value
of the spool. The delta p of the pressure compensator is adjustable via
an adjusting screw on the outside of the valve.
Tightening torque delta p adjusting screw: 10 Nm
SCHEME A
SCHEMEB/C
M16-B M16-C
By selecting a pressure compensator in the control section, the ow
rate is regulated individually and load-independently per function. Each
control section can be individually congured with a wide variety of
modules. The actuation functions "electrical", "hydraulical" and "manual”
can be added to the control section to guarantee high exibility of the
variants. A manual override function is also possible for the electrical
and hydraulical operating modes.
The complete PMV-16 control unit can be constructed from up to 12
dierent control sections.
NOTE!
B (Boost ow spring), the pressure drop of the compensator
cannot be adjusted.
PMV - M16 - - - - K8
Pressurecompensator
A Without pressure compensator
B With pressure compensator
C With pressure compensator and non-return valve function
S Spacer plate Width = 14 mm (1/4" of a section)
S1 Spacer plate Width = 28 mm (1/2" of a section)
Pressurecompensatorspring
Nominal volume ow rate Q
N
see spool kit PMV-S16
N No pressure compensator (for option A & S only)
S Standard ow spring (100 % ow)
Spring/-kit (others on request)
L Low ow spring (56 % ow) 800.2006
H High ow spring (120 % ow) 800.2005
B Boost ow spring (180 % ow) 800.9006
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
Page 7 => SYMBOL A
Page 9 => SCHEME
Page 7 & 8 => M16-B
Page 7 => M16-C
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS T
T LS
b a
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
Page 11 => SCHEME
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T T LS
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 7 => SYMBOL A
Page 9 => SCHEME
Page 7 & 8 => M16-B
Page 7 => M16-C
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS T
T LS
b a
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
Page 11 => SCHEME
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T T LS
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
SPACERPLATEM16-S/S1
For more space between sections, there is the option of using two types
of standard spacer plates. The S plate has 1/4 of a section and S1 is
1/2 section width.
NOTE! The Tie rods PMV-T16 have lengths of the width of
the control sections.
www.wandfluh.com Illustrations are not binding Data subject to change 8/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
ELECTRICAL-PROPORTIONAL PMV-P16 FOR CONTROL SECTION
ELECTRICAL-PROPORTIONAL
The electrically-proportionally actuated version uses an electrical
control module that controls the main spool of the control section via 2
proportional pressure reducing valves.
The pressure reducing valves are available in 12VDC and 24 VDC with
dierent connector versions.
The control module PMV-P16 can be used optionally in combination with
the spring cap PMV-D16 or the manual override PMV-L16.
The cap contains an adjustment screw for ow limitation.
Tightening torque of the fastening screws: 6 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
Limiting current at 50°C 1500 mA at 12 VDC
750 mA at 24 VDC
Solenoid resistance 4.72 Ω ±5 % at 12 VDC
20.8 Ω ±5 % at 24 VDC
SCHEME
PMV - P16 - - - K8
Voltage
12 12 Volt DC
24 24 Volt DC
Electricalspecications
SJ Connector socket AMP Junior - Timer
SG Plug socket Deutsch DT04 - 2P
XA ATEX (IECEx, CCC, EAC) L15*
XU AUS Australia L15*
XM MA L15*
XC UC NEC 500 / NEC 505 L15*
EH EHA On-board elect. CAN & Spool feedback
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
* Other electrical specifications see data sheet 1.1-183
Page 7 => SYMBOL A
Page 9 => SCHEME
Page 7 & 8 => M16-B
Page 7 => M16-C
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS T
T LS
b a
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
Page 11 => SCHEME
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T T LS
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 9/19 Edition: 24 04 3.0-20E
1. POSITION SENSOR
CURRENT DRIVER
2. ELECTRIC BOARD
INPUT SIGNAL
3. PROPORTIONAL
CONTROL VALVES
. .
LVDT
EHA
CAN
1
2
3
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
ELECTRICAL DATA
Voltage 24 V
No-load current 20 mA
Max power consumption 25 W
Device Connector Deutsch Connector DT14-6P
Protection class up to IP6K6 / IPX9K
Switching time pilot t
on
< 50 ms (pA = 0 % to 90 %)
t
o
< 50 ms (pA = 100 % to 10 %)
SAFETYFUNCIONS(ELECTRONICSONLY)
The EHA provides three safety functions in complaince of DIN EN ISO 13849
SAFETY FUNCTION 1 SAFETYFUNCTION2 DIAGNOSTIC FUNCTION 3
Current less state Pressure less state Rated customer diagnostic
function ‒ EHA diag-message
Description Whenever the signal process-
ing of setpoints along the rated
safety-chain (CAN … valve-coil)
is disturbed, the valves enter
the current less state, which is
dened as the safe state.
Whenever the signal processing
of setpoints along the rated safe-
ty-chain (CAN … pilot-pressure)
is disturbed, the valves enter
the pressure less state, which is
dened as the safe state.
The current position of the valve
slider (accuracy ±4 %) is trans-
mitted via the CAN bus interface
cyclically (user congurable inter-
vals of 10ms, 30ms and 100ms)
accompanied by an error code in
case one has occurred.
MTTFd 46,6 years 28,7 years 77,8 years
Diagnostic coverage 97 % (mid: 90 % to 99 %) 72 % (low: 60 % to 90 %) 96 % (mid: 90 % to 99 %)
Performance Level D C D
EHAON-BOARDELECTRONICSCAN&SPOOLFEEDBACK
www.wandfluh.com Illustrations are not binding Data subject to change 10/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
SENSORIC ACCURACY
SENSOR TYPE HALL EFFECT
Range ± 8 mm
Redudant sensoric yes
Absolut accuracy < 1,0 % (± 3 mm)
< 2,5 % (± 8 mm)
< 3,5 % (± 9 mm)
Temperature coecient
(-25°C–100°C)
± 300ppm/°C (<± 8 mm
± 500ppm/°C (>± 8 mm
PIN ASSIGNMENT
PIN NUMBER FUNCTION
1 U Bat (batterie voltage)
2 CAN_L CAN Signal (dominant low)
3 "Aout (analog output signal)
Ain (analog input signal)"
4 Agnd (analog output ground)
5 GND (battery ground)
6 CAN_H CAN Signal (dominant high)
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 11/19 Edition: 24 04 3.0-20E
SPRING CAP PMV-D16 FOR CONTROL SECTION
SPRING CAP D16
The spring cap D16 is used for the electrical and hydraulical operating
form. The cap is used to hold the spring assembly and contains an
adjustment screw for ow limitation.
Tightening torque of the fastening screws: 6 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
PMV - D16 - - K8
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
HYDRAULICAL
In the hydraulically actuated version, instead of the electrical-proportional
control module, a hydraulic control module is used, which contains ports
(A, B) for the hydraulic joysticks.
The port dimension is designed in ¼"BSP.
The pilot pressure range of the hydraulic joysticks used should be 6
to 22 bar.
The control module PMV-H16 can be used optionally in combination with
the spring cap PMV-D16 or the manual override PMV-L16.
The cap contains an adjustment screw for ow limitation.
Tightening torque of the fastening screws: 6 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
SCHEME
Page 7 => SYMBOL A
Page 9 => SCHEME
Page 7 & 8 => M16-B
Page 7 => M16-C
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS T
T LS
b a
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
Page 11 => SCHEME
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T T LS
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
PMV - H16 - - - K8
Portconnection
G Thread in BSP
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
HYDRAULICAL PMV-H16 FOR CONTROL SECTION
www.wandfluh.com Illustrations are not binding Data subject to change 12/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
MANUAL PMV-L16 FOR CONTROL SECTION
MANUAL L16
The manual cap L16 is used for the manually operated function only or
the manual override function.
The cap is used to hold the spring assembly and contains an adjustment
screw for ow limitation.
Tightening torque of the fastening screws: 6 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
Lever force: 26 N
Centre position lever: Standard horizontal,
can optionally be mounted rotated by 30° in both directions.
Lever stroke range for full deection: +/- 30°
MANUALLY OPERATED PMV-A16 FOR CONTROL SECTION
MANUALLY ACTUATED
For fully manual control sections, the end cap A16 is used in combination
with the manual cap L16.
The cap contains an adjustment screw for ow limitation.
Tightening torque of the fastening screws: 6 Nm.
Tightening torque of the nut with ow limitation: 10 Nm
SCHEME
PMV - L16 - - K8
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
PMV - A16 - - K8
Sealtype
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
Page 7 => SYMBOL A
Page 9 => SCHEME
Page 7 & 8 => M16-B
Page 7 => M16-C
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T
T
LS
b a
P
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS T
T LS
b a
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
BLS
T
T
LS
b a
Page 11 => SCHEME
P Pilot
L
T1
P
LS
A B LSBLSA
PT T
A
B
LS
T T LS
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 13/19 Edition: 24 04 3.0-20E
SPOOL PMV-S16
SYMBOL
PMV - S16 - - - -
SymbolSpool
ACB
ADB
Ratio
1 1:1
2 2:1 (high ow in A)
NominalvolumeowrateQ
N
100 100 l/min
075 75 l/min
050 50 l/min
030 30 l/min
Springassembly
H Manual control only (A16 with L16)
F Manual control only, with friction brake (A16 with L16)
E Electrical / hydraulical control (P16 or H16 with D16)
O Electrical / hydraulical control – manual override (P16 or H16 with L16)
PT
A B
T
LSA LSB
PT
A B
T
LSA LSB
Spool with closed centre position Spool with open centre position
A / B 20 % open to the tank
ACB ADB
The various spool sets consist of spool and spring assembly and can
be mounted in any variation in the honed bore of the control section
due to the high production accuracy.
In order to cover the entire volume ow range, there are various spools
with corresponding control edges.
Spools with a ow ratio of 1:1, but also spools with a ow ratio of 2:1
can be congured for the corresponding cylinder applications.
The PMV programme provides a wide range of spool types. The most
common spools are available with closed or open centre position, but
special shapes are also available. Flexibility is further increased with the
choice of pressure compensator delta p setting in the control section to
precisely set the required ow rate.
FRICTIONBRAKE
There are detent positions in the middle and also in the end of each
stroke position (center position, fully open on "a" and fully open on "b").
In between, the hand lever can be positioned freely on each angle
position and then the lever will stay in this position.
www.wandfluh.com Illustrations are not binding Data subject to change 14/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
CONNECTION PLATE PMV-C16
PMV - C16 - - - - - - K8
Type
N A/B port only
H A/B port & LS relief
C A/B port & LS relief & optional cartridge
Max.settingLSpressurerelief
N Without (N & C plate only)
1 100 bar
4 420 bar
CartridgeoptionssideA
N No options (If type C or S no cartridge mounted)
T Shock suction function For type C
A Pressure relief in user port, <280bar For type C
B Pressure relief in user port, >280bar For type C
S Suction function For type C
CartridgeoptionssideB
N No options (If C or S no cartridge mounted)
T Shock suction function For type C
A Pressure relief in user port, <280bar For type C
B Pressure relief in user port, >280bar For type C
S Suction function For type C
Portconnection
G Thread in BSP 3/4"
S Thread in SAE-ORB 12
Sealtype
NN No seals (N plate only)
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 15/19 Edition: 24 04 3.0-20E
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
CONNECTION PLATE C16-C
The connection plate type C16-C is an extended design.
In addition to the LS pressure relief valves, this plate can be extended
with additional cartridges for various functions. Possible variants of
built-in cartridges are the suction function (S), the pressure relief func-
tion (B) and the shock suction function (T). The cartridges can be used
independently on the A and B sides.
These additional valves in A and B act directly on the working port. This
is in contrast to the LS pressure limitations, which act on the LS signal.
SCHEME C
C-TT
C-BB
C-SS
CONNECTION PLATE C16-N
The basic connecting plate type C16-N has only the ports A and B.
CONNECTION PLATE C16-H
LS pressure relief valves are integrated in the connection plate type
C16-H on the A and B sides.
SCHEME N
SCHEME H
SURFACE TREATMENTS
Cartridges for PMV-C16-C are zinc coated.
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Page 9 => SYMBOL
Page 11 => SYMBOL
Page 14 => SYMBOL N
P Pilot
A B LSBLSA
PT T
b a
P Pilot
A B LSBLSA
PT T
Page 14 => SYMBOL H
Page 14 => SYMBOL C
Page 14 => C-BB
Page 14 => C-TT
Page 14 => C-SS
A B
A BYa Yb
A BYa Yb
A BYa Yb
A BYa Yb
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
www.wandfluh.com Illustrations are not binding Data subject to change 16/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
END PLATE PMV-E16
PMV - E16 - - - - K8 -
Plateversion
A Small end plate without ports
B With additional P2 and T2 port
C With Z port, with additional P2 and T2 port
R Reduction plate size 16/10
Portconnection
G Thread in BSP
S Thread in SAE-ORB
N No ports (A plate only)
Sealtype
NN No seals (A plate only)
D4 Seals HNBR 90
D1 Seals Viton
Surfaceprotection
K8 Zinc-nickel
Options
L Internal L (Drain) to T
WIDE END PLATE E16-B
The PMV end plate type E16-B includes an extra P and T port in addition
to the LS pressure relief of the shuttle valve cascade.
SCHEME B
Page 15 => SYMBOL B
Page 15 => SYMBOL A
Page 15 => SYMBOL C
T2
P
Z
T2
P
Z
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
WIDE END PLATE E16-C
The PMV end plate type E16-C includes an extra P and T port.
In addition, the LS signal of a downstream valve unit can be connected to
the upstream valve unit via the Z port (series connection of two blocks).
SCHEME C
Page 15 => SYMBOL B
Page 15 => SYMBOL A
Page 15 => SYMBOL C
T2
P
Z
T2
P
Z
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
SMALL END PLATE E16-A
The PMV end plate type E16-A only contains the LS pressure relief of
the shuttle valve cascade.
SCHEME A
Page 15 => SYMBOL B
Page 15 => SYMBOL A
Page 15 => SYMBOL C
T2
P
Z
T2
P
Z
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
NOTE!
Using the reduction inlet plate PMV-R22, it is necessary
to have on both sides the (wide) endplate.
PMV-E22-B/C (size 22 side) and PMV-E16-B/C (size16
side)
SMALL END PLATE E16-A-L
The PMV end plate type E16-A-L contains the LS pressure relief of the
shuttle valve cascade and drain connected internal to T.
SCHEME A-L
NOTE!
Back pressure from T can inuence of the valve function.
We recommend that use this only together with PMV-L16
& -A16.
Page 15 => SCHEME B
Page 15 => SCHEME A-L
Page 15 => SCHEME C
T2
P
Z
T2
P
Z
Page 15 => SCHEME A
Dokument darf ohne schriftliche Einwilligung weder kopiert,
verwertet noch an Dritte weitergegeben werden.
Zuwiderhandlung ist strafbar und wird gerichtlich verfolgt.
Blatt
Revision
Gezeichnet
Freigegeben
Geprüft
Datum Name Änderungsbeschrieb
Ersetzt durch:
Ersatz für:
Dok.-Nr.
Art.-Nr.
Rev.
Änderungsnr.
Format
1 1
A2
von
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 17/19 Edition: 24 04 3.0-20E
Tierods PMV - T16 -
S01 Tie rod kit small, end plate A, 1 section
S02 Tie rod kit small, end plate A, 2 sections
S03 Tie rod kit small, end plate A, 3 sections
S04 Tie rod kit small, end plate A, 4 sections
S05 Tie rod kit small, end plate A, 5 sections
S06 Tie rod kit small, end plate A, 6 sections
S07 Tie rod kit small, end plate A, 7 sections
S08 Tie rod kit small, end plate A, 8 sections
S09 Tie rod kit small, end plate A, 9 sections
S10 Tie rod kit small, end plate A, 10 sections
S11 Tie rod kit small, end plate A, 11 sections
S12 Tie rod kit small, end plate A, 12 sections
W01 Tie rod kit wide, end plate B/C, 1 section
W02 Tie rod kit wide, end plate B/C, 2 sections
W03 Tie rod kit wide, end plate B/C, 3 sections
W04 Tie rod kit wide, end plate B/C, 4 sections
W05 Tie rod kit wide, end plate B/C, 5 sections
W06 Tie rod kit wide, end plate B/C, 6 sections
W07 Tie rod kit wide, end plate B/C, 7 sections
W08 Tie rod kit wide, end plate B/C, 8 sections
W09 Tie rod kit wide, end plate B/C, 9 sections
W10 Tie rod kit wide, end plate B/C, 10 sections
W11 Tie rod kit wide, end plate B/C, 11 sections
W12 Tie rod kit wide, end plate B/C, 12 sections
TIE RODS
For the assembly of complete PMV-16 control blocks, 2 dierent tie
rod kits are available, which are used depending on the type of end
plate used.
The tie rod kits each consist of 3 pcs. tie rods and M8 nuts with plastic
caps.
The tie rods are in Cr-steel material and the M8 nuts are Zinc-nickel
coated.
Q = f (l) Volumeow-signal-characteristics
Spool types ACB, ADB
K4276
Q [l/min]
I [mA]
500
1000
600
1200
400
800
300
600
200
400
0
0
24 VDC
12 VDC
100
200
700
1400
180
160
140
120
100
80
60
40
20
0
Q = 120 l/min
Q = 180 l/min
Q = 100 l/min
Q = 75 l/min
Q = 50 l/min
Q = 30 l/min
PERFORMANCE SPECIFICATIONS
Oil viscosity = 30 mm2/s
Δp = f (Q) Pressuredropvolumeowcharacteristic
Recirculation curve 3-way pressure compensator
Inlet plate type B16-F
K4278
∆p [bar] P → T
Q [l/min]
2502001501000 50 300
30
25
20
15
10
5
0
B16-H
B16-F
Q = f (p) Volumeow-pressure-characteristics
Pressure compensator type M16-B
Q = f (Δp) Volumeow-pressure-characteristics
Control section without pressure compensator
K4286
Q [l/min]
∆p [bar]
504030200 10
220
200
180
160
140
120
100
80
60
40
K4277
Q [l/min]
p [bar]
3002001000 420
200
175
150
125
100
75
50
25
0
Q = 120 l/min
Q = 180 l/min
Q = 100 l/min
Q = 80 l/min
Q = 60 l/min
Q = 40 l/min
www.wandfluh.com Illustrations are not binding Data subject to change 18/19 Edition: 24 04 3.0-20E
Proportional Mobile Valve PMV-16
DIMENSIONS
Dimension drawing
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
1
6
0
Page 1 of 2
H
Envelope requirement acc.to
to third parties without permission in written form.
-0.3
Format
E
-0.1
Chamfers
Abstract general tolerances ISO 2768-1
>0,5-3 >3-6
+0.4
>6-30
±0.2±0.1Linear dimensions
>30-120
±0.5
±0.1
±0.2 ±1
H
±0.3
H
0289340
Nominal dimension
F
E
D
M 1:2
00
Radiuses,
Violation is illegal and will be legally prosecuted.
C:\00_Wandfluh\Artikelhierarchie\01_Verkaufsartikel\Stack valves\PMV-16\DEMO PMV-16 Massskizze
Ra 3.2
C
B
A0
ISO 14405
erstellt
Surface finish
ECNRev.
G
Doc.-No.
Replacement for:
Replaced by:
P/N:
Edges acc. ISO 13715
ECN-Description
Concentricity, axial runout
Name
7VIAL
Date
08.06.2021
Checked
Released
Drawn
m
34.687 kg
m
Weight
H
Revision
Material:
This document must not be copied, exploited or submitted
ISO 2768
A
B
C
D
E
F
G
H
I
J
1234
5
67
89
10
10
9
876
5
4321 1 1
11 12 13 14
A
Linear dimensions, radiuses,
Chamfers, angle
Straightness, flatness
Rectangularity, symmetry
General
tolerances
Model reference: Doc.-No. 0287696 / Configuration 001
Befestigungsgewinde
M8x12
M
8
x
1
2
328.35
136 89
51 49
M
8
x
1
2
6
103.1
BSP SAE ORB
P1, T1, T2: 3/4" 12
A,B: 3/4" 12
LS: 1/4" 6
L: 1/4" 6
Ya, Yb: 1/4" 6
Ppilot: 1/4" 6
Z: 1/4" 6
Befestigungsgewinde
M8x12
Befestigungsgewinde
M8x12
M
8x
12
6
M8
x
1
2
6
79
54
6.5
M
8
x
1
2
3
0
°
3
0
°
183.2
205.2
73.5
312
56 56 56 56 14.5
121
M
8
x
1
2
M
8
x
1
2
48
124
6
30
111
M
8
x
1
2
8
M
8
x
1
2
55
56
51
110
46
32.5
68.5
56
14
4
11
7
3
2
8
5
13
12
9
10
6
15
127
142
PMV-P16-XA
PMV-P16-EH
Proportional Mobile Valve PMV-16
www.wandfluh.com Illustrations are not binding Data subject to change 19/19 Edition: 24 04 3.0-20E
HYDRAULIC PORT
Port BSP SAE ORB
Port P, T G3/4“ 12
Port A, B G3/4“ 12
Port LS G1/4“ 6
Port L (Drain) G1/8“ 4
Port Ya, Yb G1/4“ 6
Port Z G1/4“ 6
WEIGHTS PER PMV MODULE
PMV-B16-F / H / P 5,4 kg
PMV-B16-V 4,6 kg
PMV-M16 3,5 kg
PMV-P16 1,3 kg
PMV-P16-EH 2,3 kg
PMV-P16-XA 3,8 kg
PMV-H16 0,7 kg
PMV-D16 0,3 kg
PMV-L16 0,6 kg
PMV-A16 0,4 kg
PMV-S16 0,2 kg
PMV-C16-N 1,4 kg
PMV-C16-H 1,9 kg
PMV-C16-C 3,4 kg
PMV-E16-A 1,0 kg
PMV-E16-B / C 3,2 kg
WEIGHTSPERTIERODKIT
PMV-T16-W01 0,2 kg
PMV-T16-W02 0,2 kg
PMV-T16-W03 0,3 kg
PMV-T16-W04 0,4 kg
PMV-T16-W05 0,4 kg
PMV-T16-W06 0,5 kg
PMV-T16-W07 0,6 kg
PMV-T16-W08 0,6 kg
PMV-T16-W09 0,7 kg
PMV-T16-W10 0,7 kg
PMV-T16-W11 0,8 kg
PMV-T16-W12 0,9 kg
WEIGHTSPERTIERODKIT
PMV-T16-S01 0,1 kg
PMV-T16-S02 0,2 kg
PMV-T16-S03 0,2 kg
PMV-T16-S04 0,3 kg
PMV-T16-S05 0,4 kg
PMV-T16-S06 0,4 kg
PMV-T16-S07 0,5 kg
PMV-T16-S08 0,6 kg
PMV-T16-S09 0,6 kg
PMV-T16-S10 0,7 kg
PMV-T16-S11 0,8 kg
PMV-T16-S12 0,8 kg
WEIGHTS PER PMV MODULE
PMV-B00-A-G 1,0 kg
PMV-B00-I-G 1,4 kg
PMV-B00-P-G 1,4 kg
PMV-B00-O-G 0,8 kg
PMV-B00-C-G 0,7 kg
ASSEMBLY INSTRUCTIONS
Type of mounting Control unit in sandwich construction
with threaded connection.
Mounting holes on the inlet and end
plate M8 x 12
Mounting position any
Tightening torque
Tie rods
M = 25 Nm
Socket Tool 13 mm
ASSEMBLY OF THE CONTROL UNIT
Various M8x12 mounting threads are available for the assembly of the
control unit:
Inlet plate:
PMV-B16: 6 x mounting thread M8x12
End plate:
PMV-E16: 3 x mounting thread M8x12