Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
3114G B2011 Rev 1.4 - PAGE 1/20
The Sunfab variable displacement pump with its rugged
construction is designed for direct mounting at the auxi-
liary drive (P.T.O.) of commercial vehicles.
With a max. displacement of 130 cm
3
/rev. and a peak
pressure of 450 bar it is suited for many applications.
This is complemented by the high self priming rate and
the low noise level. The pump delivery flow is dependent
on the present drive speed and geometric displacement.
The flow is adjust able in a range between 0 and Q
max.
Long service life is ensured due to the pressurized lubri-
cation of the swash plate bearing shell.
Sunfab SVH is rotation-direction dependent and should
be ordered in either right-hand or left-hand
designs.
Other advantages of Sunfab SVH:
• Short reaction time when resetting the flow
• Compact installation dimensions
• High working pressure level allowed
• Externally drained for best cooling
• Rugged construction and long service life
• Low noise emission
• High power-to-weight-ratio
3115 GB
SVH 062, 092, 112, 130
GB
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH - 092 R DYN - 2 - LSNR/ZL - 2/65 - 350 - C 022
SVH 062 SVH 092 SV H 112 SVH 130
62.4 87.2 110.4 130
350 350 350 400
400 400 400 450
21.5° 21.5° 21.5° 21.5°
0.85 0.85 0.85 0.85
2 2 2 2
3 3 3 3
430 530 900 900
430 530 600 700
100 530 600 700
2500 2300 2200 2100
500 500 500 500
100 151 184 230
53 79,5 97.2 120
24 27 30 30.8
30 35.3 40 40
0.005 0.008 0.01 0.011
75 75 75 75
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 2/20
Versions, main data
(Example)
Basic type
Nominal size
062
092
112
130
Direction of rotation:
L = Left-hand (counter clockwise)
R = Right-hand (clockwise)
always facing the drive shaft
Shaft design:
D = Splined shaft conforming
DIN ISO 14 (for trucks)
M = Spline shaft DIN 5480
only SVH 092, 112
S = Spline shaft SAE-C J 744
H = Spline shaft SAE-B J 744
only SVH 062
T = Spline shaft SAE-B-B J 744
only SVH 062
U = Spline shaft SAE-B J 744(short)
only SVH 062
Q = Spline shaft SAE-C S
only SVH 112, 130
Mounting flange design (input side):
Y = Flange ISO 7653-1985 (for trucks)
P = Flange ISO 7653-1985 10° (for
trucks), only SVH 112, 130
G = Flange ISO 3019-2, only SVH 092
F = Flange SAE-C-4-Hole J 744
ISO 3019-1
Z = Flange SAE-B-4-Hole J 744
ISO 3019-1, only SVH 062
X = Flange SAE-B-2-Hole-45°offset
J 744 ISO 3019-1, only SVH-062
Mounting flange design
(output side), see page 5
no coding = Ports conforming
ISO 228/1 (BSPP)
UNF = Ports conforming
SAE J 514
Pressure specification (bar)
no coding = Without stroke limitation
(standard)
2 = With stroke limitation
(not available for versions
with thru-shaft SVH 062, 092, 112)
2 /... = Factory set stroke limitation,
specification V
g
(cm
2
/rev.)
Pump controllers / Intermediate plates,
see page 3
Shaft design/Housing design:
1 = Standard, suction port and
pressure outlet axial
2 = Thru-shaft, suction port and
pressure outlet radial
3 = Standard, suction port and
pressure outlet radial
4 = Standard, suction and pressure port
SAE axial, only SVH 092
Seals:
N = NBR (Nitrile rubber) - Standard
V = FKM
Type
Geometric displacement V
g
cm
3
/rev.
Nom. pressure p
nom
bar
Pressure p
max
bar
Angle of the swash plate
Required inlet pressure (absolute) for open circuit bar
Max. permissible inlet pressure, absolute bar
Max. permissible housing pressure, absolute bar
Max. permissible drive torque (flange/shaft) Nm
Max. torque for the pump (with power controller) Nm
Max. permissible torque for the thru-shaft, dep. on flange Nm
Max. rev. rating when self priming and max. angle of the swash plate
at 1 bar absolute inlet pressure
rpm
Min. rev. rating for permanent running rpm
Required torque at 100 bar Nm
Drive power for 250 bar and 2000 rpm kW
Mass (weight) complete with controller kg
Tare weight torque Nm
Inertia moment kg m
2
Sound level at 250 bar, 1500 rpm and max. swash plate angle
(Measured in a sound measuring room DIN ISO 4412, distance 1 m)
dB(A)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
20 ... 400 50 350
20 ... 55 10 27
29.4
45.1
www.hawe.de | 2013 03-2013-00 - D 7960 N 35
Controller
Intermediate plate version, coding /ZL Coding /L (only for type V60N-130)
Image 62: Controller coding /ZL
Image 63: Controller coding /L
1.
Power setting
Pressure adjustment
Pressure range (bar)
Δp (bar) /revolution
Default pressure setting (bar)
Pressure limitation 20 ... 400 approx. 50 250
Differential pressure Δp
(only type LSNR)
20 ... 55 approx. 12.5 20
Port X (ISO 228/1): G 1/4
LS signal port, order reference for adapter for UNF thread 79.93 245
Caution
Always monitor the pressure gauge when setting or changing the pressure!
SVH 062, 092, 112, 130
29.4
45.1
3114G B2011 Rev 1.4 - PAGE 3/20
Intermediate plate
Coding /ZW version with thru-shaft
Controller
Coding /ZL intermediate plate version
Ports ISO 228/1 (BSPP):
LS = LS signal port G 1/4
Differential pressure ∆p
1
)
2
)
(Stand-by pressure)
1
) Applies only coding LSNR.
2
) The adjustment range is limited by a mechanical stop. Attention: Always use a pressure gauge when changing the pressure setting!
Pressure limitation
2
)
approx.
approx.
approx.
approx.
approx.
Pressure adjustment Pressure range (bar) ∆p (bar)⁄rev. Pressure setting, factory set (bar)
Pressure limitation
Differential pressure ∆p
Description of the controllers
LSNR Load-Sensing controller with integrated pressure limitation
NR Pressure controller, adjustable directly at the pump. The Pressure
controller automatically maintains a constant system pressure
independant of the required flow. Therefore it is suited for constant
pressure systems, where differing flow is required or as efficient pressure
limitation of the hydraulic system
Intermediate plates Intermediate plate only in combination with controllers LSNR or NR
/ZL SVH 062, 092, 112: Intermediate plate with power controller (torque limitation)
Product ”Pressure x Displacement” = constant
Adjustment range: 25...100% of max. drive torque
/ZW Angled intermediate plate (45°) mandatory for mounting controllers at
pumps with housing design -2, -3
/L SVH 130: Power controller (torque limitation), default option
Adjustment range: 200-700 Nm
Factory setting: 700 Nm
Controller
Coding /LSNR, NR
Controller
Coding /L
Torque setting:
190 Nm/rev
Torque setting:
190 Nm/rev
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
Typ V60N-130
Kennzeichen .../L
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 4/20
Controller symbols
Coding LSNR Coding NR
Coding .../ZL Coding .../L
for SVH 130
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
V
g
x n x h
v
1000
1,59 x V
g
x ∆p
100 x h
mh
2p x M x n
60000
M x n
9549
Q x ∆p
600 x h
t
062 092-112 130
C 011 C 021 C 031 9T 16/32 DP
C 012 C 022 C 032 9T 16/32 DP
1)
C 013 -- -- 11T 16/32 DP
C 014 C 024 C 034 13T 16/32 DP
C 015 C 025 C 035 13T 16/32 DP
-- -- -- 15T 12/24 DP
-- C 027 -- 14T 12/24 DP
-- C 028 C 038 14T 12/24 DP
-- -- -- 17T 12/24 DP
SAE C 14T 12/24 DP
DIN ISO 014 B8x32x36
SAE C
DIN ISO 014
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 5/20
Additional parameter, general
Calculation of the nom. sizes:
Flow rate Torque Power
Q = (lpm) M = (Nm) P = = =
V
g
Displacement (cm³/rev.) h
v
= Volumetric efficiency
∆
p
Differential pressure (bar) h
mh
= Mechanical-hydraulic efficiency
n Speed (rpm) h
t
= Total efficiency (h
t
= h
v
x h
mh
)
Nomenclature Axial piston pump according to the swash plate principle
Mounting At the auxiliary drive of commercial vehicles
(flange ISO 7653-1985 for trucks)or flange assembly
(flange ISO 3019-2 or SAE/ISO 3019-1)
Surface Gas nitrocarburized SVH 062, 092, 112. Painted SVH 130
Direction of rotation Right or left
Changing the rotation direction Contact Sunfab
Installed position Any (observe the installation instructions)
Hydraulic fluid Hydraulic oil acc. to DIN 51524 part 1 to 3; ISO VG 10 to 68 acc. to DIN 51519
Viscosity range: min. approx. 10; max. approx. 1000 mm
2
/sec
Optimal operation range: approx. 20...50 mm
2
/sec. Also suitable are biologically degradable pressure
fluids type HEES (synth. Ester) at operation temperatures up to approx. +70 °C.
Temperature Ambient: approx. -40...+60 °C
Fluid: -25...+80 °C, pay attention to the viscosity range!
Start temperature down to -40 °C is allowable (Pay attention to the viscosity range during start!),
as long as the operation temperature during subsequent running is at least 20 °C higher.
Filtration Should conform to ISO standard 4406 code 21/18/15 ...19/17/13
Mounting flange design (output side)
Available, incl. coupling sleeves Coupling flange for universal joint shafts
Attention: Observe the max. drive torque rating!
Note: An additional support has to be provided in case of pump combinations.
Additional versions on request!
1
) ANSI B 92.1, FLAT ROOT SIDE FIT
The spline width is not conforming the industrial standard. s = 2.357
-0.03
Coding, SVH
Flange Shaft
SAE A-2-Hole
SAE A-2-Hole
SAE A-2-Hole
SAE B-2-Hole
SAE B-4-Hole
SAE B-B-2-Hole
SAE C-2-Hole
SAE C-4-Hole
SAE C-C-2-Hole
Coding Spline profile
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVHÊ112
SVHÊ62
SVHÊ92
t in ms
p
(1 abs.)
Abbildung 6: p Druck (bar); Q Förderstrom (l/min)
1.
Förderstrom
2.
Leistung
3.
Leistung (Nullhub)
Regelzeiten T1
Regelzeiten T2
Abbildung 9: p Druck (bar); T1
Regelzeit(ms)
Abbildung 10: p Druck (bar); T2
Regelzeit(ms)
Abbildung 6: p Druck (bar); Q Förderstrom (l/min)
1.
Förderstrom
2.
Leistung
3.
Leistung (Nullhub)
Regelzeiten T1
Regelzeiten T2
Abbildung 9: p Druck (bar); T1
Regelzeit(ms)
Abbildung 10: p Druck (bar); T2
Regelzeit(ms)
Abbildung 6: p Druck (bar); Q Förderstrom (l/min)
1.
Förderstrom
2.
Leistung
3.
Leistung (Nullhub)
Regelzeiten T1
Regelzeiten T2
Abbildung 9: p Druck (bar); T1
Regelzeit(ms)
Abbildung 10: p Druck (bar); T2
Regelzeit(ms)
Abbildung 6: p Druck (bar); Q Förderstrom (l/min)
1.
Förderstrom
2.
Leistung
3.
Leistung (Nullhub)
Regelzeiten T1
Regelzeiten T2
Abbildung 9: p Druck (bar); T1
Regelzeit(ms)
Abbildung 10: p Druck (bar); T2
Regelzeit(ms)
SVH 130
SVH 112
SVH 62
SVH 92
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 6/20
Curves
Ss = Regulating distance actuator
Tu = Delay < 3 ms
T1 = Response time min to max
T2 = Response time max to min
p = Pressure
LS-line min. length 1.5 m, min. internal diameter 12 mm
approx. 4 bar
Pressure (bar)
Pressure (bar)
Controller curve
Coding L
Pressure / Delivery flow
Delivery flow Q (%)
Response time T
1
(LSNR-controller)
Inlet pressure (LSNR-controller)
Graph valid at viscosity 75 mm
2
/s at
max. setting angle.
Response time T
1
(ms) Inlet pressure (bar)
Delivery flow (l/min)
Pressure (bar)
Speed (rpm)
Response time T
2
(LSNR-controller)
Response time T2 (ms)
Pressure (bar)
Coding LSNR
Geometric displacement (%)
Pressure p
B
(bar)
Flow and Power
Charts show flow/pressure (without controller). Power at max.
setting angle and power at min.setting angle and 1500 rpm
Delivery flow (112)
Delivery flow (092)
Delivery flow (062)
Power (112)
Power (092)
Power (062)
Power (zero stroke)
Power (kW)
Delivery flow (130)
Power (130)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
45.1
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 7/20
Basic pumps: SVH 062
Rotation direction, clockwise (R)
(facing the input shaft)
Rotation direction, counter clockwise (L)
(facing the input shaft)
Mounting flange
design (input side)
coding Y
ISO 7653-1985
Splined shaft
coding D
conforming
DIN ISO 14
Stroke limitation
Ports (ISO 228/1 (BSPP)):
P = Pressure outlet G 3/4
S = Flange, suction port
D = Case drain G 3/4
Coding UNF ports conforming SAE J 514:
P = 1 1/16-12 UN-2B
S = Flange, suction port
D = 1 1/16-12 UN-2B
LS = G 1/4 (ISO 228/1 (BSPP)) with adaptor for 7/16-20 (SAE-4)
Max. torque 120 Nm
(4 x tie rod M12x170)
Stroke limitation
(V
g
approx. 4 cm
3
/rev.)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 8/20
Mounting flange
design (input side)
coding F
ISO 3019-1 127-4
(SAE C-4-Hole)
Spline shaft
coding S
SAE C 14T 12/24DP
Spline shaft
coding U
SAE B 13T
16/32DP short
Spline shaft
coding H
SAE B 13T
16/32DP
Mounting flange
design (input side)
coding Z
ISO 3019-1 101-4
(SAE B-4-Hole)
Mounting flange
design (input side)
coding X
ISO 3019-1 101-2
(SAE B-2-Hole)
Spline shaft
coding T
SAE BB 15T
16/32
Bleeding G 1/8 (BSPP)
Bleeding G
1/8 (BSPP)
Additional input shaft designs
Additional mounting flange design
(with mounting flange design coding Y)
(with mounting flange design coding F, Z, X)
For missing dimensions, see coding Y
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH 062, 092, 112, 130
Flanschausführung (abtriebsseitig)
Kennzeichen C 015
(SAE B-4-Loch)
Abbildung 27: C 015
1.
Abstützung 8xM8
Flanschausführung (abtriebsseitig)
Kennzeichen C 015
(SAE B-4-Loch)
Abbildung 27: C 015
1.
Abstützung 8xM8
89,8
89,8
3114G B2011 Rev 1.4 - PAGE 9/20
SVH 062 with thru-shaft
Housing design
Coding 2
2xM10,
16 deep
Mounting flange design
(output side)
coding C 011, C 012
(SAE A-2-Hole),
(see page 5)
Suction port A
Pressure outlet B
Right hand
A Suction port
B Pressure outlet
Left hand
A Pressure outlet
B Suction port
For port sizes,
see page 7
Mounting flange design
(output side)
coding C 014
(SAE B-2-Hole)
(see page 5)
Housing design
Coding 3
(mounting flange design coding Y)
(mounting flange design coding F, Z, X)
For missing dimensions, see coding Y
For available mounting flange designs (output side) and coupling sleeves, see page 5
Mounting flange design
(output side)
coding C 015
(SAE B-4-Hole)
M8 (Support)
M8 (Support)
M8 (Support)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
45.1
SVH 062, 092, 112, 130
20
3114G B2011 Rev 1.4 - PAGE 10/20
Rotation direction, clockwise (R)
(facing the input shaft)
Rotation direction, counter clockwise (L)
(facing the input shaft)
Mounting flange
design (input side)
coding Y
ISO 7653-1985
Splined shaft
coding D
conforming
DIN ISO 14
Stroke
limitation
Additional input shaft designs Additional mounting flange design
(mounting flange design coding G, F)
(mounting flange design coding Y)
Spline shaft
coding M
DIN 5480
W30x2x14x9g
Mounting flange design
(input side)
coding G
ISO 3019-2-125 B4 HW
Ports (ISO 228/1 (BSPP)):
P = Pressure outlet G1
S = Flange, suction port
D = Case drain G 3/4
Coding UNF ports conforming SAE J 514:
P = 1 5/16-12 UN-2B
S = Flange, suction port
D = 1 1/16-12 UN-2B
LS = G 1/4 (ISO 228/1 (BSPP)) with adaptor for 7/16-20 (SAE-4)
Max. torque 150 Nm
(4 x tie rod M14x190)
Stroke limitation
(V
g
approx. 5 cm
3
/rev.)
SVH 092
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 11/20
SVH 092 with thru-shaft
Mounting flange
design (input side)
coding F
ISO 3019-1 127-4
(SAE C-4-Hole)
Spline shaft
coding S
14T-12/24 DP
(SAE C)
Suction port A Pressure outlet B
Right hand
A Suction port
B Pressure outlet
Left hand
A Pressure outlet
B Suction port
For port sizes, see page 10
Mounting flange
design (output side)
coding C 021, C 022
(SAE A-2-Hole)
(see page 5)
M10, 15 deep
Bleeding G 1/8 (BSPP)
(mounting flange design coding Y)
(mounting flange design coding F, Z, X)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH 062, 092, 112, 130
M12
M12,
M16
M16,
M 12
4
M12
M12,
M16
M16,
Portar
P = SAE 3/4” (6000 psi)
S = SAE 2” (3000 psi)
89,8
89,8
3114G B2011 Rev 1.4 - PAGE 12/20
Mounting flange
design (output side)
coding C 025
(SAE B-4-Hole)
(see pos. page 5)
Mounting flange
design (output side)
coding C 028
(SAE C-4-Hole)
(see page 5)
Mounting flange
design (output side)
coding C 024
(SAE B-2-Hole)
(see page 5)
Mounting flange
design (output side)
coding C 027
(SAE C-2-Hole)
(see page 5)
Housing design
Coding 3
Housing design
Coding 4
For available mounting flange
designs (output side) and
coupling sleeves, see page 5
15 deep
15 deep
SVH 092
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH 112
SVH 062, 092, 112, 130
45.1
45.1
45.1
45.1
- 0.001
- 0.002
3114G B2011 Rev 1.4 - PAGE 13/20
Ports (ISO 228/1 (BSPP)):
P = Pressure outlet G1
S = Flange, suction port
D = Case drain G 3/4
Coding UNF ports conforming SAE J 514:
P = 1 5/16-12 UN-2B
S = Flange, suction port
D = 1 1/16-12 UN-2B
LS = G 1/4 (ISO 228/1 (BSPP)) with
adaptor for 7/16-20 (SAE-4)
Rotation direction, clockwise (R)
(facing the input shaft)
Rotation direction, counter clockwise (L)
(facing the input shaft)
Mounting flange
design (input side)
coding Y
ISO 7653-1985
Mounting flange
design (input side)
coding F, ISO 3019-1
127-4 (SAE C-4-Hole)
Splined shaft
coding D
DIN ISO 14
Splined shaft
coding S
14T-12/24DP (SAE C)
Stroke limitation
Max. torque 150 Nm
(4 x tie rod M14x190)
Stroke limitation
(Vg approx. 6 cm3/rev.)
Bleeding G 1/8 (BSPP)
Additional input shaft designs and
mounting flange design
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH 062, 092, 112, 130
M12
M10,
M12
M10,
M12
M10,
M12
M10,
3114G B2011 Rev 1.4 - PAGE 14/20
Right hand
A Suction port
B Pressure outlet
Left hand
A Pressure outlet
B Suction port
For port sizes, see page 13
SVH 112 with thru-shaft
Housing design
Coding 2
Mounting flange design
(output side)
coding C 021, C 022 (SAE A-2-Hole)
(see page 5)
Suction port A
Pressure outlet B
(mounting flange design coding Y)
(mounting flange design coding F)
G 1/8 (BSPP)
15 deep
Mounting flange design
(input side)
Coding P
ISO 7653-1985
Spline shaft
Coding Q
SAE CS
Ansi B92.1 21T 16/32 DP
Additional input shaft designs
Additional mounting flange design
Spline shaft
Coding M
DIN 5480 W30x2x14x9g
M8 (Support)
M8 (Support)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
M16
M12,
M12,
SVH 062, 092, 112, 130
M12
M10,
M16
M12,
M12,
89,8
89,8
3114G B2011 Rev 1.4 - PAGE 15/20
Mounting flange
design (output side)
coding C 027 (SAE C-2-Hole)
(see page 5)
Mounting flange
design (output side)
coding C 025 (SAE B-4-Hole)
(see page 5)
Mounting flange
design (output side)
coding C 028 (SAE C-4-Hole)
(see page 5)
Housing design
Coding 3
15 deep
15 deep
Mounting flange design
(output side)
coding C 024
(SAE B-2-Hole)
(see page 5)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
45.1
SVH 130
ISO 3019-1 127-4 (SAE C-4-Loch)
14T-12/24 DP (SAE C)
SAE CS
C
D
E
ISO 3019-1 127-4 (SAE C-4-Loch)
14T-12/24 DP (SAE C)
SAE CS
C
D
E
ISO 3019-1 127-4 (SAE C-4-Loch)
14T-12/24 DP (SAE C)
SAE CS
C
D
E
LS
SVH 062, 092, 112, 130
- 0.001
- 0.002
3114G B2011 Rev 1.4 - PAGE 16/20
Rotation direction, clockwise (R)
(facing the input shaft)
Mounting flange
design (input side)
coding Y
ISO 7653-1985
Mounting flange
design (input side)
coding F, ISO 3019-1
127-4 (SAE C-4-Hole)
Splined shaft
coding D
DIN ISO 14
Splined shaft
coding S
14T-12/24DP (SAE C)
Stroke limitation
(approx. 13 cm3/rev)
Ports (ISO 228/1 (BSPP)):
P = Pressure outlet G 1
S = Flange, suction port
D = Case drain G 3/4
Coding UNF ports conforming SAE J 514:
P = 1 5/16-12 UN-2B
S = Flange, suction port
D = 1 1/16-12 UN-2B
LS = G 1/4 (ISO 228/1 (BSPP))
with adaptor for 7/16-20 (SAE-4)
Bleeding G 1/8 (BSPP)
Additional input shaft designs and
mounting flange design
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
ISO 3019-1 127-4 (SAE C-4-Loch)
14T-12/24 DP (SAE C)
SAE CS
C
D
E
ISO 7653-1985
Flanschausführung (abtriebsseitig)
Kennzeichen C 31, C 34, C 35, C 38
Abbildung 58: Flanschausführung C31, C34, C35, C38
F
G
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 17/20
Mounting flange design
(input side)
coding P
ISO 7653-1985
Spline shaft
coding Q
21T 16/32 DP (SAE-CS)
Additional input shaft designs
Additional mounting flange design
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
M12
M10,
ISO 7653-1985
Flanschausführung (abtriebsseitig)
Kennzeichen C 31, C 34, C 35, C 38
Abbildung 58: Flanschausführung C31, C34, C35, C38
F
G
LS
SVH 062, 092, 112, 130
3114G B2011 Rev 1.4 - PAGE 18/20
SVH 130 with thru-shaft
Housing design
Coding 2
Mounting flange design
(output side)
coding C 031 (SAE A), C 034,
C035 (SAE B), C 038 (SAE C)
(see page 5)
Suction port A
Pressure outlet B
Right hand
A Suction port
B Pressure outlet
Left hand
A Pressure outlet
B Suction port
For port sizes, see page 13
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
Flanschausführung (abtriebsseitig)
Kennzeichen C 31
Flanschausführung (abtriebsseitig)
Kennzeichen C 34
Abbildung 59: Flansch C31
Abbildung 60: Flansch C34
Flanschausführung (abtriebsseitig)
Kennzeichen C 35
Flanschausführung (abtriebsseitig)
Kennzeichen C 38
Abbildung 61: Flansch C35
Abbildung 62: Flansch C38
H
Flanschausführung (abtriebsseitig)
Kennzeichen C 31
Flanschausführung (abtriebsseitig)
Kennzeichen C 34
Abbildung 59: Flansch C31
Abbildung 60: Flansch C34
Flanschausführung (abtriebsseitig)
Kennzeichen C 35
Flanschausführung (abtriebsseitig)
Kennzeichen C 38
Abbildung 61: Flansch C35
Abbildung 62: Flansch C38
H
Flanschausführung (abtriebsseitig)
Kennzeichen C 31
Flanschausführung (abtriebsseitig)
Kennzeichen C 34
Abbildung 59: Flansch C31
Abbildung 60: Flansch C34
Flanschausführung (abtriebsseitig)
Kennzeichen C 35
Flanschausführung (abtriebsseitig)
Kennzeichen C 38
Abbildung 61: Flansch C35
Abbildung 62: Flansch C38
H
Flanschausführung (abtriebsseitig)
Kennzeichen C 31
Flanschausführung (abtriebsseitig)
Kennzeichen C 34
Abbildung 59: Flansch C31
Abbildung 60: Flansch C34
Flanschausführung (abtriebsseitig)
Kennzeichen C 35
Flanschausführung (abtriebsseitig)
Kennzeichen C 38
Abbildung 61: Flansch C35
Abbildung 62: Flansch C38
H
SVH 062, 092, 112, 130
106.4
114, 5
M8
M12
M12
M12
146
89,8
3114G B2011 Rev 1.4 - PAGE 19/20
Mounting flange
design (output side)
coding C 034
(see page 5)
Mounting flange
design (output side)
coding C 031
(see page 5)
Mounting flange
design (output side)
coding C 035
(see page 5)
Mounting flange
design (output side)
coding C 038
(see page 5)
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: sunfab@sunfab.se Web: www.sunfab.com
SVH 062, 092, 112, 130
© Copyright 2015 Sunfab Hydraulics AB. All Rights Reserved.
3114G B2011 Rev 1.4 - PAGE 20/20
WARNING
When the pump is running:
1. Do not touch the pressure hose
2. Watch out for rotating parts
3. The pump and hoses may be hot
Sunfab reserves the right to make changes in design and dimensions without notice. Printing and typesetting errors reserved.
