110
7
19
M24x1,5
ø38
34
22,2
HP
P
T
HP-Connection: 1/4" BSP
P & T Connections: 1/8" BSP
2
ScanWill - More Pressure. More Power
ScanWill compact hydraulic pressure intensifiers offer an easy,
energy-saving, safe and cost-efficient solution to achieving a higher output
pressure from an existing low-pressure power source.
Low pressure supplied to the inlet port
– say 15 - 200 bar / 218 - 2,900 psi – is transformed to a higher pressure at
the outlet port – from 20 - 4,000 bar / 290 - 58,000 psi.
ScanWill intensifiers are offered in cast iron and steel
with a chrome finish as well as in stainless steel for the oil & gas sector.
Technology
ScanWill intensifiers are based on a piston principle where a larger
diameter piston pushes a smaller diameter piston thus increasing
the pressure to a factor equal to the ratio: Larger diameter area
divided by smaller diameter area.
The outlet pressure will always be proportionate to
the supplied pressure.
The diagram shows the basic principle of the ScanWill
intensifiers consisting of a piston arrangement, a Piston
Control Valve PCV, Check Valves CV1 & CV2 and
the Pilot Operated check Valve POV.
110
7
19
M24x1,5
ø38
34
22,2
HP
P
T
HP-Connection: 1/4" BSP
P & T Connections: 1/8" BSP
110
7
19
M24x1,5
ø38
34
22,2
HP
P
T
HP-Connection: 1/4" BSP
P & T Connections: 1/8" BSP
LOW/MEDIUM PRESSURE | MP-S
MultiPlier Small is a compact all-round in-line hydraulic
pressure intensifier for use in limited space.
Features:
• In-line pressure intensifier
• End pressure range: 20 - 800 bar / 290 - 11,600 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
Technical Specications
Ratio Max.
Inlet Flow
Max.
Supply Pressure
Max.
Output Pressure
( i ) (LPM / GPM) (bar / psi) (bar / psi)
2.0 8.0 / 2.1 200 / 2,900 400 / 5,800
2.4 8.0 / 2.1 200 / 2,900 480 / 6,960
2.8 8.0 / 2.1 200 / 2,900 560 / 8,120
3.4
8.0 / 2.1
200 / 2,900 680 / 9,860
4.0
8.0 / 2.1 200 / 2,900 800 / 11,600
5.0
8.0 / 2.1 160 / 2,320 800 / 11,600
7.0
8.0 / 2.1 114 / 1,653 800 / 11,600
9.0
8.0 / 2.1 89 / 1,290 800 / 11,600
3
113
47,5
16
18
51
28
51
M28x1,5
33
2 off M4x6
for mounting
on both sides
HP-Connection
46
T
P
P & T Connections: ¼” BSP or 7/16-20 unf
HP Connection: ¼” BSP or 9/16-18 unf
MP-T | LOW/MEDIUM PRESSURE
MultiPlier Tube is an all-round in-line hydraulic
pressure intensifier for tube connections.
Features:
• In-line pressure intensifier
• End pressure range: 20 - 800 bar / 290 - 11,600 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
Technical Specications
Ratio Max.
Inlet Flow
Max.
Supply Pressure
Max.
Output Pressure
(i) (LPM / GPM) (bar / psi) (bar / psi)
1.5 15.0 / 4.0 200 / 2,900 300 / 4,350
2.0 15.0 / 4.0 200 / 2,900 400 / 5,800
2.8
8.0 / 2.1 200 / 2,900
560 / 8,120
3.4 15.0 / 4.0 200 / 2,900 680 / 9,860
4.0 14.0 / 3.7 200 / 2,900 800 / 11,600
5.0 14.0 / 3.7 160 / 2,320 800 / 11,600
7.0 13.0 / 3.4 114 / 1,653 800 / 11,600
9.0 13.0 / 3.4 89 / 1,290 800 / 11,600
4
25
151
ø70
44
65
P
T
HP
P & T Connections: 3/8" BSP
HP Connection: 1/2" BSP
LOW/MEDIUM PRESSURE | MP-M
MultiPlier Medium is an in-line hydraulic pressure
intensifier for medium size hydraulic systems.
Features:
• In-line pressure intensifier
• End pressure range: 20 - 800 bar / 290 - 11,600 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
– including a P.O. check Valve POV
Technical Specications
Ratio Max.
Inlet Flow
Max.
Supply Pressure
Max.
Output Pressure
(i) (LPM / GPM) (bar / psi) (bar / psi)
1.8 25.0 / 6.6 200 / 2,900 360 / 5,220
2.1 25.0 / 6.6 200 / 2,900 420 / 6,090
2.6 35.0 / 9.3 200 / 2,900 520 / 7,540
3.4 35.0 / 9.3 200 / 2,900 680 / 9,860
4.0 35.0 / 9.3 200 / 2,900 800 / 11,600
5.0 35.0 / 9.3 160 / 2,320 800 / 11,600
7.0 35.0 / 9.3 114 / 1,653 800 / 11,600
5
225
40
61
ø90
80
All connections: 1/2" BSP
HP
P
T
MultiPlier Large is an in-line hydraulic pressure intensifier
for large-sized hydraulic systems.
Features:
• In-line pressure intensifier
• End pressure range: 20 - 800 bar / 290 - 11,600 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
– including a P.O. check Valve POV
Technical Specications
Ratio Max.
Inlet flow
Max.
Supply Pressure
Max.
Output Pressure
(i) (LPM / GPM) (bar / psi) (bar / psi)
1.5 80.0 / 21.2 200 / 2,900 300 / 4,350
2.0 80.0 / 21.2 200 / 2,900 400 / 5,800
3.4 80.0 / 21.2 200 / 2,900 680 / 9,860
4.0 80.0 / 21.2 200 / 2,900 800 / 11,600
5.0 80.0 / 21.2 160 / 2,320 800 / 11,600
7.0 80.0 / 21.2 114 / 1,653 800 / 11,600
6
MP-L | LOW/MEDIUM PRESSURE
98
12
60
45
45
60
R16
28°
4 x ø6,2 for mounting
P
T
HP
7
MultiPlier Flange is a hydraulic pressure
intensifier for flange-on mounting.
Features:
• Flange-on pressure intensifier
• End pressure range: 20 - 700 bar / 290 - 10,150 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
– including a P.O. check Valve POV
Technical Specications
Ratio Max.
Inlet flow
Max.
Supply Pressure
Max.
Output Pressure
(i) (LPM / GPM) (bar / psi) (bar / psi)
1.5 15.0 / 4.0 200 / 2,900 300 / 4,350
2.0
15.0 / 4.0
200 / 2,900 400 / 5,800
2.8 8.0 / 2.1 200 / 2,900 560 / 8,120
3.4 15.0 / 4.0 200 / 2,900 680 / 9,860
4.0 14.0 / 3.7 175 / 2,538 700 / 10,150
5.0 14.0 / 3.7 140 / 2,030 700 / 10,150
7.0 13.0 / 3.4 100 / 1,450 700 / 10,150
9.0 13.0 / 3.4 78 / 1,128 700 / 10,150
LOW/MEDIUM PRESSURE |
MP-F
40,5
ø5,3
ø5,3
ø5,3
ø5,3
32,5
20,8
50
31
17,5
10,3
19
164,5
67
60
T
P
A
B
M8x9 in P & T
MultiPlier Cetop/NG6 is a hydraulic pressure
intensifier for Cetop/NG6 mounting.
Features:
• Cetop DO3 / NG6 pressure intensifier
• End pressure range: 20 - 500 bar / 290 - 7,250 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
– including a P.O. check Valve POV
Technical Specications
Ratio Max.
Inlet flow
Max.
Supply Pressure
Max.
Output Pressure
(i) (LPM / GPM) (bar / psi) (bar / psi)
1.5 15.0 / 4.0 200 / 2,900 300 / 4,350
2.0 15.0 / 4.0 200 / 2,900 400 / 5,800
2.8 8.0 / 2.1 178 / 2,589 500 / 7,250
3.4 15.0 / 4.0 147 / 2,132 500 / 7,250
4.0 14.0 / 3.7 125 / 1,812 500 / 7,250
5.0 14.0 / 3.7 100 / 1,450 500 / 7,250
7.0 13.0 / 3.4 71 / 1,036 500 / 7,250
9.0 13.0 / 3.4 56 / 806 500 / 7,250
8
MP-C | LOW/MEDIUM PRESSURE
112
56
ø68
30
18
D
HP-Connection
For mounting
2 x M4
on both sides
51
51
28
The HP-Connection and D depend
on the top Plate chosen
ø50
8
60
P & T Connections:
1/4" BSP or 7/16-20 unf
MultiPlier 2000 is a hydraulic pressure intensifier
for high-pressure power packs up to 3,000 bar / 43,500 psi.
Features:
• In-line pressure intensifier
• End pressure range: 800 - 3,000 bar / 11,600 - 43,500 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
• Selection of top plates for high pressure connection available
Technical Specications
Ratio Max.
Inlet flow
Max.
Supply Pressure
Max.
Output Pressure
(i) (LPM / GPM) (bar / psi) (bar / psi)
7.0 13.0 / 3.4 200 / 2,900 1,400 / 20,300
10.0 12.0 / 3.2 200 / 2,900 2,000 / 29,000
13.0 10.0 / 2.6 200 / 2,900 2,600 / 37,700
16.0 10.0 / 2.6 188 / 2,711 3,000 / 43,500
9
HIGH PRESSURE | MP-2000
10
The MultiPlier 1400/2000/4000 models are hydraulic pressure
intensifiers for high flow and high pressure.
Features:
• In-line pressure intensifiers
• End pressure range: 800 - 4,000 bar / 11,600 - 58,000 psi
• Reciprocating - continuously delivers flow during pressure build-up
• Multiple intensification ratios available
• All high-pressure valves are integrated
• Selection of top plates for high pressure connection available
Technical Specications
MPL Ratio Max.
Inlet flow
Max.
Supply Pressure
Max.
Output Pressure
(i)
(LPM / GPM) (bar / psi) (bar / psi)
1400
7.0
60.0 / 15.8 200 / 2,900 1,400 / 20,300
2000
10.0
50.0 / 13.2 200 / 2,900 2,000 / 29,000
2000
14.0
50.0 / 13.2 200 / 2,900 2,800 / 40,600
4000
20.0
30.0 / 7.9 200 / 2,900 4,000 / 58,000
MPL-1400/2000/4000 | HIGH PRESSURE
198,5
D
ø90
80
61
The HP-Connection and D depends
on the top plate chosen.
P
T
P & T Connections: G1/2" (1/2" BSP)
MPL-2000
HP-Connection and D depend
on the top plate chosen
61
223,5
D
ø90
80
P
T
P & T Connections: 1/2" BSP
MPL-1400
198,5
D
ø90
80
61
The HP-Connection and D depends
on the top plate chosen.
P
T
P & T Connections: G1/2" (1/2" BSP)
11
MP-T-P-7.0-R
The MP-T-P-7.0-R is a custom made pressure intensifier
built for mounting on a rotating unit.
The pressure intensifier rotates at 1,500 rpm while
intensifying a supplied pressure of 30 bar / 435 psi to
210 bar / 3,045 psi.
Features:
• In-line rotating pressure intensifier
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
MP-CT
MultiPlier CT is a hydraulic pressure intensifier for Cetop/NG6
mountings with separate high-pressure ports. A hydraulic mini power
pack can also be added when a higher end pressure is required.
Features:
• Cetop DO3 / NG6 pressure intensifier
• End pressure range: 20 - 800 bar / 290 - 11,600 psi
• Multiple intensification ratios available
• Reciprocating - continuously delivers flow
during pressure build-up
• All high-pressure valves are integrated
– including a P.O. check Valve POV
• No change of pressure in A & B ports,
separate port for high pressure
SIS-SERIES
The ScanWill Intensifier Solution is for use in hydraulic
systems where higher pressure is needed, locally.
The SIS-series is design protected.
Features:
• Compact solution - Fast to connect
• Strainer filters included
• Pressure gauge included
• Pressure setting valve included
• For single and double acting cylinders
• Multiple intensification ratios available
• Available in stainless steel
SPECIAL SOLUTIONS
MP-I
MultiPlier MP-I is a hydraulic pressure intensifier
designed as a screw-in component for
hydraulic manifolds.
Features:
• No tubing required
• Generates higher pressure only
in defined areas of the manifold
• Other manifold components do not need to
be pressure rated above pump pressure
• Multiple intensifications ratios available
• All high pressure valves are integrated
Check out our website:
www.scanwill.com
Contact us:
ScanWill Fluid Power ApS
Hassellunden 14
Smørum
DK-2765 Denmark
Telephone: +45 74 42 34 50
Email: info@scanwill.com
ScanWill has a network of
more than 40 Sales Partners
around the world providing
technical assistance and swift
customer service.
ScanWill’s entire product
range is always in stock for
day-to-day shipment
from the facilities in
Smørum, Denmark.
ScanWill has more than 25
years of production knowledge
and application experience.