Hydraulic Motor/Pump
Series F11/F12
Fixed Displacement
Hydraulic Motor/Pump
Hydraulic Motor/Pump
parker.com/pmde
2
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Conversion factors
1 kg ................................................................. 2.20 lb
1 N ............................................................... 0.225 lbf
1 Nm ......................................................... 0.738 lbf ft
1 bar ..............................................................14.5 psi
1 l ......................................................0.264 US gallon
1 cm
3
.......................................................0.061 cu in
1 mm ............................................................. 0.039 in
1°C .............................................................
5
/
9
(°F-32)
1 kW .............................................................. 1.34 hp
Conversion factors
1 lb ............................................................... 0.454 kg
1 lbf ................................................................4.448 N
1 lbf ft ..........................................................1.356 Nm
1 psi ...................................................... 0.068948 bar
1 US gallon ..................................................... 3.785 l
1 cu in .....................................................16.387 cm
3
1 in ............................................................... 25.4 mm
1°F ............................................................
9
/
5
°C + 32
1 hp...........................................................0.7457 kW
Torque (M)
M = [Nm]
Basic formulas for hydraulic motors
Flow (q)
q = [l/min]
Power (P)
P = [kW]
D x n
1000 x η
v
D x ∆p x η
hm
63
q x ∆p x η
t
600
D - displacement [cm
3
/rev]
n - shaft speed [rpm]
η
v
- volumetric efficiency
∆p - differential pressure [bar]
(between inlet and outlet)
η
hm
- mechanical efficiency
η
t
- overall efficiency
(η
t
=
η
v
x η
hm
)
Torque (M)
M = [Nm]
Basic formulas for hydraulic pumps
Flow (q)
q = [l/min]
Power (P)
P = [kW]
D x n x η
v
1000
D x ∆p
63 x η
hm
q x ∆p
600 x η
t
D - displacement [cm
3
/rev]
n - shaft speed [rpm]
η
v
- volumetric efficiency
∆p - differential pressure [bar]
(between inlet and outlet)
η
hm
- mechanical efficiency
η
t
- overall efficiency
(η
t
=
η
v
x η
hm
)
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS
CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide
product or system options for further investigation by users having technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components
and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The
user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning
the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized
distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or
specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and
sufficient for all applications and reasonably foreseeable uses of the components or systems.
Offer of Sale
Please contact your Parker representation for a detailed ”Offer of Sale”.
WARNING – USER RESPONSIBILITY
3
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Content
1
2
3
4
5
General product information General product information
General information and design, Bearing life, F11/F12 Fan motors, Pages 4 - 7
F11/F12 in saw motor applications, Parker Power Boost
Series F11 F11
Bent axis piston pump/motor with fixed displacement Pages 8 - 38
Series F12 F12
Bent axis piston pump/motor with fixed displacement Pages 39 - 59
Accessories Accessories
Flushing valves, FV13 flushing valve block, Integrated pressure relief valve, SR pressure Pages 60 - 68
relief/anticavitation valve block, SV pressure relief valve block, Speed sensor, BLA Boost units
Installation and start up information Installation and start up information
F11, F12 Pages 69 - 71
4
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Series F11
F11 is a bent-axis, fixed displacement motor/pump. It
can be used in numerous applications in both open and
closed loop circuits.
The F11 series is available in sizes 5, 6, 10, 12, 14 and
19 cc.
F11 Features
• Maxintermittentpressureupto420barand
continuous operating pressure up to 350 bar
• Thankstolowweightpistonsandacompactdesignof
the rotating parts, the F11 tolerates very high speeds,
up to 14000 rpm
• CETOP,ISO,SAWandSAEversions
Series F12
F12 is a bent-axis, fixed displacement motor/pump. It
can be used in numerous applications in both open and
closed loop circuits.
The F12 series is available in sizes 30, 40, 60, 80, 90,
110, 125, 152, 162, 182 and 250 cc.
F12 Features
• Maxintermittentpressureupto480barand
continuous operating pressure up to 420 bar
• The7or9pistondesignprovideshighstart-uptorque
and smooth motor operation
• ISO,Cartridge,SAWandSAEversions
General Features
• Thelaminatedpistonringoffersimportantadvantagessuchasunbeatableefciencyand
thermal shock resistance
• Highallowablespeedsandoperatingpressuresmeanshighoutputpower
• Theuniquepistonlocking,timinggearandbearingset-upaswellasthelimitednumberofparts
add up to a very robust design with long service life and, above all, proven reliability.
• The40°anglebetweenshaftandcylinderbarrelallowsforaverycompact,lightweightmotor/
pump.
• Smallenvelopsizeandahighpower-to-weightratio
• Themotorversionhashighlyengineeredvalveplatesforhighspeedandlownoise
• Thepumpversionhashighlyengineeredvalveplatesforincreasedselfprimingspeedandlow
noise, available with left and right hand rotation.
• TheF11'sandF12'shaveasimpleandstraight-forwarddesignwithveryfewmovingparts,
making them very reliable motors/pumps.
• Ouruniquetiminggeardesignsynchronizesshaftandcylinderbarrel,makingtheF11/F12very
toleranttohigh'G'forcesandtorsionalvibrations.
• Heavydutyrollerbearingspermitsubstantialexternalaxialandradialshaftloads.
General Information
5
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
1
F12_shaft_loads.EPS
Leif A./020204
α
F
170°
190°
Bearing_life_DE.eps
Leif A./020201
Life expectancy
(logarithmic scale)
Other
causes
Bearing
fatigue
Rotating group
fatigue and wear
System
pressure
Hydraulic unit life versus system pressure.
Bearing life
General information
Bearing life can be calculated for that part of the load/
lifecurve(shownbelow)thatisdesignated'Bearing
fatigue'.'Rotatinggroupfatigueandwear'and'Other'
caused by material fatigue, fluid contamination, etc.
should also be taken into consideration when estimating
the service life of a motor/pump in a specific application.
Bearing life calculations are mainly used when compar-
ing different frame sizes. Bearing life, designated B
10
(or
L
10
), is dependent of system pressure, operating speed,
external shaft loads, fluid viscosity in the case, and fluid
contamination level.
The B
10
value means that 90% of the bearings survive,
at a minimum, the number of hours calculated. Statisti-
cally, 50% of the bearings will survive at least five times
the B
10
life.
Required information
When requesting a bearing life calculation from Parker
Hannifin, the following information (where applicable)
should be provided:
- A short presentation of the application
- F11 or F12 size and version
- Duty cycle (pressure and speed versus time
at given displacements)
- Low system pressure
- Case fluid viscosity
- Life probability (B
10
, B
20
, etc.)
- Operating mode (pump or motor)
- Direction of rotation (L or R)
- External shaft loads (Forces, Gear, Belt, Cardan
or none)
For forces please provide:
- Axial load, Fixed radial load, Bending moment, Ro-
tating radial load and distance flange to radial load.
For Gear please provide:
- Pitch diameter, Pressure angle, Spiral angle, Dis-
tance flange – gearwheel (mid) and Gearwheel
spiral direction (R or L).
For Belt please provide:
- Pretension, Coefficient of friction, Angle of contact,
Distance flange – pulley (mid) and Diameter pulley.
For Cardan please provide:
- Shaft angle, Distance flange – first joint and dis-
tance between joints
- Angle of attack (α) as defined below
The direction (α) of the radial load is positive in the
direction of rotation as shown.
To obtain maximum bearing life, the radial load should,
in most cases, be located between 170° and 190°.
Technical information
Bearing life calculation
An application is usually governed by a certain duty or
work cycle where pressure and speed vary with time
during the cycle.
In addition, bearing life depends on external shaft
forces, fluid viscosity in the case and fluid contamina-
tion.
Parker Hannifin has a computer program for calculating
bearing life and will assist in determining F11 or F12
motor/pump life in a specific application.
6
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Technical information
F11/F12 Fan motors
F11/F12 motors, in frame sizes -5 to -40 cc, are
common in Fan applications. Some typical options are,
built in check valve, pressure relief valve, cartridge
flange and tapered shaft (refer to the schematic to the
right).
The fan motor can be operated at very high speeds
without reliability problems. The fan is usually installed
directly on the motor shaft without additional bearing
support. The F11/F12 has up to 95% overall efficiency
which reduces the diesel consumption and minimizes
the cooling demand.
Fan motor circuit
Because of the built-in anti cavitation valve, either left
hand (L) or right hand (R) rotation must be specified
when ordering the motor.
When the pump flow to the motor is shut off and the
motor is operating at very high speeds, it is important
that sufficient return port back pressure is available
(port B in the schematic to the right).
The anti cavitation valve will then open and direct flow
to the motor inlet port. If the inlet pressure is insuf-
ficient, motor cavitation will be experienced.
In an open circuit, back pressure can be created by a
counter pressure valve installed in the return line; pref-
erably, it should be pilot operated to minimize power
losses. A back pressure of about 10 bar is sufficient in
most applications.
For more drawings illustrating motors with make-up
valve, see chapters 2, F11 and 3, F12.
For more info about integrated pressure relief valves,
see page 63.
Example of ordering code
F11-010-MB-CV-K-000-MUVL-00
MUVL = Make up/anti cavitation valve, counter clock-
wise rotation
MUVR = Make up/anti cavitation valve, clockwise
rotation
Built -in
anti cavita-
tion valve
Alternative
drain port D
Main port B
Main port A
Drain port C
Type V
Tapered
shaft
Port A Port B
Port C/D
Fan motor (F11-10 left hand rotated shown).
Schematic Fan motor with anti cavitation valve
7
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
1
F11/F12 in saw motor applications
Series F11/F12 motors have proven suitable for
demanding applications such as chain saws. Primarily
due to the 40° bent-axis design, spherical pistons (with
laminated piston rings) and gear synchronization, very
high speeds are permissible. Not even low tempera-
tures at start-up affect reliability.
Because of the built-in anti cavitation valve, either left
hand (L) or right hand (R) rotation must be specified
when ordering the motor.
When the pump flow to the motor is shut off and the
motor is operating at very high speeds, it is important
that sufficient return port back pressure is available.
The anti cavitation valve will then open and direct flow
to the motor inlet port. If the inlet pressure is insuf-
ficient, motor cavitation will be experienced.
To further enhance the saw function and, at the same
time, reduce weight, cost and installation dimensions,
a specific saw motor has been developed (frame sizes
F11-6, -10, -12, -14, -19, F12-30 and -40; refer to the
illustration to the right) which is specifically dedicated
to bar saws. The motor allows the saw bar bearings
to be mounted directly on the motor housing, and the
sprocket installs on the motor shaft without additional
bearings. Catalogue MSG30-8245/UK
Parker Power Boost
A high speed F11 or F12 motor could be optimized
with a Power Boost™, which means less fluid friction
and oil compression. This can reduce power losses
by up to 5 kW. The improved efficiency generates less
heat, reducing the need for cooling and consequently
improves fuel consumption.
Parker Power Boost is available for size F11-6, -10,
-12, -14, -19 and F12-30.
When to order a motor with Power Boost it is to be
specified with a B in last field in model code. Ex below.
F11-019-SB-CS-K-000-MUVL-B0
F11_saw_motor_install.eps
Leif A./020204
F11 with built-in
Make up/anti
cavitation valve
Saw bar supported
directly on the
motor flange
Feed
cylinder
Chain sprocket mounted
directly on the shaft
Saw
chain
Protective
cover
Saw
bar
Chain saw installation (example; F11-10 shown)
Technical information
8
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
F11
Content
Content Page
Specifications .................................................................................................9
Efficiency ......................................................................................................10
Noise level ....................................................................................................10
Selfpriming speed and required inlet pressure ............................................. 11
Ordering codes
F11-CETOP .................................................................................................. 12
F11-ISO ........................................................................................................ 13
F11-SAE ....................................................................................................... 14
Installation dimensions CETOP
F11-005 ........................................................................................................15
F11-006, -010 ............................................................................................... 16
F11-012 ........................................................................................................18
F11-014 ........................................................................................................20
F11-019 ........................................................................................................22
Installation dimensions ISO
F11-006, -010 ............................................................................................... 24
F11-012 ........................................................................................................26
F11-014 ........................................................................................................28
Installation dimensions SAE
F11-006, -010 ............................................................................................... 30
F11-012 ........................................................................................................32
F11-014 ........................................................................................................34
F11-019 ........................................................................................................36
9
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
Specifications
Frame size F11 -005 -006 -010 -012 -014 -019
Displacement [cm
3
/rev] 4.9 6.0 9.8 12.5 14.3 19.0
Operating pressure
max intermittent
1)
[bar] 420 420 420 420 420 420
max continuous [bar] 350 350 350 350 350 350
Motor operating speed [rpm]
max intermittent
1)
14 000 11 200 11 200 10 300 9 900 8 900
max continuous
3)
12 800 10 200 10 200 9 400 9 000 8 100
min continuous 50 50 50 50 50 50
Max pump selfpriming speed
2)
L or R function; max [rpm] 4 600 – 4 200 3 900 3 900 3 500
Motor input flow
max intermittent
1)
[l/min] 69 67 110 129 142 169
max continuous [l/min] 63 61 100 118 129 154
Drain temperature
3)
, max [°C] 115 115 115 115 115 115
min [°C] -40 -40 -40 -40 -40 -40
Theoretical torque at 100 bar [Nm] 7.8 9.5 15.6 19.8 22.7 30.2
Mass moment of inertia
(x10
-3
) [kg m
2
]
0.16 0.39 0.39 0.40 0.42 1.1
Weight [kg] 4.7 6.5 6.5 7.5 7.5 11
1) Intermittent: max 6 seconds in any one minute.
2) Selfpriming speed valid at sea level. Find more info on page 11
3) See also installation information. Page 69
10
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
Efficiency
Because of its high overall efficiency, driving a motor/
pump from series F11 requires less fuel or electric
power. Also, it allows the use of a small reservoir and
heat exchanger, which in turn reduce cost, weight, and
installation size.
The diagrams to the right show volumetric and
mechanical efficiencies of an F11-5 motor.
F11-19 motors can be equipped with Power Boost
which in high speed applications can decrease the
mechanical losses by up to 15%, see page 7.
Contact Parker Hannifin for efficiency information on a
particular F11 frame size that is being considered.
Noise level
Series F11 feature low noise levels from low to high
speeds and pressures.
The noise level is measured in a semi-anechoic room,
1 m behind the unit. As an example, the diagram to the
right shows the noise level of an F11-005.
The noise level for a particular motor/pump may vary
±2 dB(A) compared to what is shown in the diagram.
NOTE: Noise information for F11/F12 frame sizes
are available from Parker Hannifin.
Technical information
100
98
96
94
92
90
1000 2000 3000 4000 5000
300
200
∆p [bar]
[%]
100
98
96
94
92
90
1000 2000 3000 4000 5000
300
200
∆p [bar]
[%]
Speed [rpm]
Speed [rpm]
Mechanical efficiencies
Volumetric efficiencies
Noise level
[dB(A)]
Pressure
[bar]
50
55
60
65
70
75
80
100 200 300 400
5000 rpm
3000 rpm
1000 rpm
11
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
2000 3000 4000 5000 6000 7000 8000 9000
F11-010F11-012/014F11-019
F11-005
2,0
1,5
1,0
0,5
0
-0,5
0 1000 2000 3000 4000 5000 6000 7000
F11-006
F11-010
F11-012/014F11-019
F11-005
2,0
1,5
1,0
0,5
0
-0,5
Selfpriming speed and required inlet
pressure
Series F11
In pump applications, the F11 with function L (counter
clockwise rotation) or R (clockwise rotation) is normally
used. The L and R (pump) provide the highest self
priming speeds (see table) as well as the lowest
noise level. The M and H (motor) function can also be
used as a pump, in either direction, but at a lower self
priming speed.
Operating above the self priming speed (refer to
Diagram 1) requires increased inlet pressure. As an
example, at least 1.0 bar is needed when operating
the F11-19-M as a pump at 3500 rpm. An F11 used
as a motor (e.g. in a hydrostatic transmission), may
sometimes operate as a pump at speeds above
the selfpriming speed; this requires additional inlet
pressure. Insufficient inlet pressure can cause pump
cavitation resulting in greatly increased pump noise
and deteriorating performance.
Inlet_pressure_gauge.eps
Leif A./020204
Inlet pres-
sure
gauge
Inlet pressure
[bar]
0.15 bar vacuum 0.15 bar vacuum
Diagram 1. Min required inlet pressure for Motor.
Inlet pressure
[bar]
Selfpriming speed [rpm]Selfpriming speed [rpm]
Diagram 2. Min required inlet pressure for Pump.
The inlet pressure can be charged by external pump, pressurized reservoir or using BLA Boost unit
Find more info about the BLA unit at page 68.
Technical information
F11 Motor version F11 Pump version
Function L or R
M H
F11-5 4600 3800 3200
F11-6 3100
F11-10 4200 3100 2700
F11-12 3900 - 3000*
F11-14 3900 - 3000*
F11-19 3500 2400 2100
* Valve plate S
12
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
F11-CETOP
x: Available (x): Optional – : Not available
Ordering codes
F11 — — —— — — —
Frame
size
Function
Main
ports
Mounting
flange
Shaft
seal
Shaft
Version
number
Option
page 6
Option
page 7, 67
Frame size 5 6 10 12 14 19
Code Function
M Motor x x x - - x
Q Motor, low noise x - x x x x
S Motor, high speed - - (x) (x) (x) (x)
H Motor, high pressure (x) - (x) - - (x)
R Pump,clockwiserot'n (x) - (x) (x) (x) (x)
L Pump, counter clockw. (x) - (x) (x) (x) (x)
For other versions, contact Parker Hannifin
Frame size 5 6 10 12 14 19
Code Option
0000 Standard x x x x x x
MUVR Make up/Anti
cavitation valve
clockwise rotation
- (x) (x) (x) (x) (x)
MUVL Make up/Anti
cavitation valve
counter clockwise
rotation
- (x) (x) (x) (x) (x)
Frame size 5 6 10 12 14 19
Code Shaft*
K Metric key x x x x x x
J Metric key (x) (x) (x) (x) - -
P Metric key - - - - (x) -
A Spline, DIN 5480 - (x) (x) (x) - -
D Spline, DIN 5480 x x x x x x
S Spline, SAE (x) - - - - -
V Tapered shaft - (x) (x) (x) (x) -
*See also dimensional drawings on pages 15-23.
Frame size 5 6 10 12 14 19
Code Shaft seal
V FPM, high pressure,
high temperature
x x x x x x
For other versions, contact Parker Hannifin
Frame size
Code Displacem.
(cm
3
/rev)
005 4.9
006 6.0
010 9.8
012 12.5
014 14.3
019 19.0
Frame size 5 6 10 12 14 19
Code Main ports
B BSP threads x x x x x x
U SAE, UN threads (x) (x) (x) (x) (x) (x)
Frame size 5 6 10 12 14 19
Code Mounting flange
C CETOP flange x x x x x x
Frame size 5 6 10 12 14 19
Code Option
00 Standard x x x x x x
P_ Prepared for speed sensor - (x) (x) (x) (x) (x)
B_ Power Boost and Prepared
for speed sensor
- (x) (x) (x) (x) (x)
_T Painted Black (x) (x) (x) (x) (x) (x)
Version number
(assigned for special
versions)
NOTE: All combinations are not valid, please contact
Parker Hannifin
13
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
Frame size 6 10 12 14
Code Function
M Motor x x - -
Q Motor, low noise - x x x
S Motor, high speed - (x) (x) (x)
H Motor, high pressure - (x) - -
R Pump,clockwiserot'n - (x) (x) (x)
L Pump, counter clockw. - (x) (x) (x)
For other versions, contact Parker Hannifin
Frame size 6 10 12 14
Code Option
0000 Standard x x x x
MUVR Make up/Anti
cavitation valve
clockwise rotation
(x) (x) (x) (x)
MUVL Make up/Anti
cavitation valve
counter clockwise
rotation
(x) (x) (x) (x)
Frame size 6 10 12 14
Code Shaft*
K Metric key x x x x
J Metric key (x) (x) (x) -
P Metric key - - - (x)
A Spline, DIN 5480 (x) (x) (x) -
D Spline, DIN 5480 x x x x
V Tapered shaft (x) (x) (x) (x)
*See also dimensional drawings on pages 25-29.
Frame size 6 10 12 14
Code Option
00 Standard x x x x
P_ Prepared for speed sensor (x) (x) (x) (x)
B_ Power Boost and Prepared
for speed sensor
(x) (x) (x) (x)
_T Painted Black (x) (x) (x) (x)
F11-ISO
x: Available (x): Optional – : Not available
Ordering codes
F11 — — —— — — —
Frame
size
Function
Main
ports
Mounting
flange
Shaft
seal
Shaft
Version
number
Option
page 6
Option
page 7, 67
Frame size 6 10 12 14
Code Shaft seal
V FPM, high pressure,
high temperature
x x x x
For other versions, contact Parker Hannifin
Frame size
Code Displacem.
(cm
3
/rev)
006 6.0
010 9.8
012 12.5
014 14.3
Frame size 6 10 12 14
Code Main ports
F Metric threads - x x x
B BSP threads x (x) (x) (x)
M Side ports, metric - (x) (x) (x)
Frame size 6 10 12 14
Code Mounting flange
I ISO flange x x x x
Version number
(assigned for special
versions)
NOTE: All combinations are not valid, please contact
Parker Hannifin
14
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
Ordering codes
F11-SAE
x: Available (x): Optional – : Not available
F11 — — —— — — —
Frame
size
Function
Main
ports
Mounting
flange
Shaft
seal
Shaft
Version
number
Option
page 6
Option
page 7, 67
Frame size 6 10 12 14 19
Code Shaft seal
V FPM, high pressure,
high temperature
x x x x x
For other versions, contact Parker Hannifin
Frame size
Code Displacem.
(cm
3
/rev)
006 6.0
010 9.8
012 12.5
014 14.3
019 19.0
Frame size 6 10 12 14 19
Code Main ports
U SAE, UN threads x x x x x
B BSP threads (x) (x) (x) (x) (x)
Frame size 6 10 12 14 19
Code Mounting flange
S SAE flange x x x x x
Version number
(assigned for special
versions)
Frame size 6 10 12 14 19
Code Function
M Motor x x - - x
Q Motor, low noise - x x x x
S Motor, high speed - (x) (x) (x) (x)
H Motor, high pressure - (x) - - (x)
R Pump,clockwiserot'n - (x) (x) (x) (x)
L Pump, counter clockw. - (x) (x) (x) (x)
For other versions, contact Parker Hannifin
Frame size 6 10 12 14 19
Code Option
0000 Standard x x x x x
MUVR Make up/Anti
cavitation valve
clockwise rotation
(x) (x) (x) (x) (x)
MUVL Make up/Anti
cavitation valve
counter clockwise
rotation
(x) (x) (x) (x) (x)
Frame size 6 10 12 14 19
Code Shaft*
T SAE key - - - x x
S SAE spline x x x x x
K Metric key x x x - -
J Metric key (x) (x) (x) - -
V Tapered shaft (x) (x) (x) (x) -
*See also dimensional drawings on pages 31-37.
Frame size 6 10 12 14 19
Code Option
00 Standard x x x x x
P_ Prepared for speed sensor (x) (x) (x) (x) (x)
B_ Power Boost and Prepared
for speed sensor
(x) (x) (x) (x) (x)
_T Painted Black (x) (x) (x) (x) (x)
NOTE: All combinations are not valid, please contact
Parker Hannifin
15
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
F11-005
(CETOP versions)
Installation dimensions
84 max
38
65
5
54
40
5
40°
9
13
134 max
96 max
8
25
9
20
M6x12 min
Ø127 max
Ø11 (x2)
100
W18x1,25x13x9g
F11_5_install.eps
Leif A./031008
18
35
28
CCW
CW
Type C mounting flange
Flange C
Key 6x6x30
Type K key shaft
Approx.
center of
gravity
Type D spline shaft (DIN 5480)
Type S spline shaft (13T16/32 DP)
47.5
88.5
113.5
20.5
Ø80
(+0/-0.046)
Ø18 (+0.008/-0.003)
Ø20.3
Ø21.81
R 0.5
R 0.7
Drain port C
(BSP1/4")
Drain port C
9/16"-18 UNF
O-ring boss;
SAE J514d
Main port A
(BSP 1/2")
Main port A
3/4"-16 UNF
O-ring boss;
SAE J514d
Main port B
(BSP 1/2")
Main port B
3/4"-16 UNF
O-ring boss;
SAE J514d
Drain port D
(BSP1/4")
Main ports Code U
16
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
94 max
46
79
11 53
101
63
40°
9
14
156 max
116 max
133
8
30
Ø152 max
Ø13 (x2)
125
CCW
CW
F11-006, -010
(CETOP versions)
Installation dimensions
Type C mounting flange
Flange C
Approx.
center of
gravity
R 0.5
Drain port C
(BSP3/8")
Main port A
(BSP 3/4")
Main port B
(BSP 3/4")
Drain port D
(BSP3/8")
Ø100 (
+0/-0.054)
17
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
AB
(55)
(149)
50
7
Ø23
22
42
43
23
2
Ø4
M6x12 min
28
M10x16 min
5/8 UNF-2A
26
CCW
CW
156 max
95
25°
68
44
(28)
F11-006, -010
(CETOP versions)
Installation dimensions
Key 6x6x35
Type K key shaft
(Std)
22.5
R 0.7
Ø20
(+0.009/-0.004)
Ø25 (+0.009/-0.004)
Type J key shaft
(Opt.)
Key 8x7x35
3.5
Spline shaft D
W20x1.25x14x9g;
DIN 5480
Spline shaft A
W 25x1.25x18x9g
DIN 5480
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown).
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
Speed sensor
(optional)
Shaft options
18
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
AB
116
max
Ø13 (x2)
125
152 max
CCW
CW
40°
(x4)
101
46
30
102
53
101
14 (x2)
156
max
133
8
9
F11-012
(CETOP versions)
Installation dimensions
Main port A
(BSP 3/4")
Flange C
Drain port D
(BSP3/8")
Ø100 (
+0/-0.054)
Main port B
(BSP 3/4")
Type C mounting flange
19
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
AB
(59)
CCW
CW
M6x12 min
102
(45)
25°
72
(149)
(32)
156
max
50
7
Ø23
42
22
28
M10x16 min
26
43
23
2
Ø4
9
5/8 UNF-2A
F11-012
(CETOP versions)
Installation dimensions
Speed sensor
(optional)
Type K key shaft
(Std)
Spline shaft D
W20x1.25x14x9g;
DIN 5480
Ø20
(+0.009/-0.004)
22.5
Key 6x6x35
Ø25 (+0.009/-0.004)
Type J key shaft
(Opt.)
Key 8x7x35
3.5
Spline shaft A
W 25x1.25x18x9g
DIN 5480
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Shaft options
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
20
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
BA
100
157
max
14
102
53
125
Ø13 (x2)
114
150
39° (x4)
102
46
30
8
133
F11-014
(CETOP versions)
Installation dimensions
Flange C
Type C mounting flange
Main port B
(BSP 3/4")
Drain port C
(BSP3/8")
Drain port D
(BSP3/8")
Main port A
(BSP 3/4")
R 0.5
9.5
Ø100 (
+0/-0.054)
CCW CW
21
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
BA
25°
149
157
max
102
4572
(32)
59
Ø27
42
8
28
M8x16 min
26
43
23
2
Ø4
5/8 UNF-2A
M6x12 min
50
7
Ø27
F11-014
(CETOP versions)
Installation dimensions
Speed sensor
(optional)
CCW CW
Type K
key shaft
Spline shaft D
W 25x1.25x18x9g
DIN 5480
Key
8x7x35
R 0.7
3.5
Ø25
(+0.009/-0.004)
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Shaft options
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
Type P key shaft
Ø20
(+0.009/-0.004)
22.5
Key 6x6x35
22
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
88
11
63
114 max
54
58
165 max
29
23
138
25
100
16
10
45°
126
Ø172 max
Ø14 (x2)
140
CCW
CW
F11-019
(CETOP version)
Installation dimensions
Type C mounting flange
Approx.
center of
gravity
Flange C
R 1.2
max
Drain port C
(BSP3/8")
Main port A
(BSP 3/4")
Main port B
(BSP 3/4")
Drain port D
(BSP3/8")
Ø112 (
+0/-0.054)
23
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
110
150
27
33
163 max
28
61
65
(150)
25°
M8x16 min
28
42
CCW
CW
F11-019
(CETOP version)
Installation dimensions
Type K
key shaft
Key
8x7x35
3.5
Ø28.3
Ø25
(+0.009/-0.004)
Spline shaft D
W 25x1.25x18x9g
DIN 5480
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Shaft options
Speed sensor
(optional)
24
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
F11-006, -010
(ISO versions)
Installation dimensions
95
79
53
145
max
95 (max)
46
30
12
123
7
Ø9 (x4)
(Ø103)
B
B
A
ccw
cw
Main port A
M22x1.5
16 deep min
ISO 9974-1
Flange I
(ISO 3019/2)
Drain port
M12x1.5
14 deep min
ISO 9974-1
Ø80
+0/-0.046
10.5 (x4)
Main port B
M22x1.5
16 deep min
ISO 9974-1
19.5
18.5
92.5
72.8
R 0.5 max
R 4.5 (x4)
25
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
95
68
44
145
max
(149)
28
55
B
A
ccw
cw
B
25°
68
28
50
7
Ø23
22
42
43
23
2
Ø4
M6x12 min
28
M10x16 min
5/8 UNF-2A
26
F11-006, -010
(ISO versions)
Installation dimensions
Spline shaft D
W20x1.25x14x9g;
DIN 5480
Ø20
(+0.009/-0.004)
22.5
3.5
Key 6x6x35
Ø25 (+0.009/-0.004)
Key 8x7x35
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Shaft options
Type K key shaft
(Std)
Type J key shaft
(Opt.)
Spline shaft A
W 25x1.25x18x9g
DIN 5480
Speed sensor
(optional)
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
Side ports M (both sides)
M22x1.5
14 deep min
ISO 9974-1
Only for F11-010
26
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
95
102
101
46
30
12
53
Ø9 (x4)
(Ø103)
B
A
ccw
cw
90
123
147
max
7
F11-012
(ISO versions)
Installation dimensions
Ø80 +0/-0.046
Flange I
(ISO 3019/2)
Main port A
M26x1.5
16 deep min
ISO 9974-1
Drain port
M16x1.5
12 deep min
ISO 9974-1
Main port B
M26x1.5
16 deep min
ISO 9974-1
18.5
19.5
R 0.5
72.8
10.5 (x4)
R 4.5 (x4)
27
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
102
72
45
50
7
Ø23
B
A
ccw
cw
139
147
max
(59)
(32)
72
(32)
M6x12 min
28
M10x16 min
42
28
22
43
23
2
Ø4
5/8 UNF-2A
F11-012
(ISO versions)
Installation dimensions
3.5
Speed sensor
(optional)
Ø20
(+0.009/-0.004)
Type K key shaft
(Std)
22.5
Key 6x6x35
Type J key shaft
(Opt.)
Ø25 (+0.009/-0.004)
Key 8x7x35
Shaft options
Spline shaft D
W20x1.25x14x9g;
DIN 5480
Spline shaft A
W 25x1.25x18x9g
DIN 5480
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
Side ports M (both sides)
M22x1.5
14 deep min
ISO 9974-1
28
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
BA
101
46
30
12
21
90
147
max
102
53
(Ø103)
Ø9 (x4)
95
123
CCW
CW
F11-014
(ISO versions)
Installation dimensions
Drain port D M16x1.5
(depth 12; ISO 9974-1)
Flange I
(ISO 3019/2)
Type I mounting flange (ISO 3019/2)
Drain port C M16x1.5
(depth 12; ISO 9974-1)
10.5 (x4)
R4.5 (x4)
R 0.5 max
6.7
18.5
Ø80
(+0/-0.046)
72.8
Main port A
M26x1.5
16 deep min
ISO 9974-1
Main port B
M26x1.5
16 deep min
ISO 9974-1
29
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
F11-014
(ISO versions)
Installation dimensions
BA
28
M8x16 min
Ø27
139
147
max
42
102
45
25°
28
43
23
2
Ø4
5/8 UNF-2A
(59)
(32)
72
25°
(32)
72
CCW
CW
50
7
Ø27
M6x12 min
Speed sensor
(optional)
Type K
key shaft
Key 8x7x35
Spline shaft D
W25x1.25x18x9g
(DIN 5480)
3.5
Ø25
(+0.009/-0.004)
Shaft options
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
Side ports M (both sides)
M22x1.5
14 deep min
ISO 9974-1
Ø20
(+0.009/-0.004)
Type P key shaft
22.5
Key 6x6x35
30
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
F11-006, -010
(SAE versions)
Installation dimensions
29° (x4)
102
133
122 max
177 (max)
146
CCW CW
R14
(x4)
79
53
30
17
(x2)
156 max
55
94 max
46
Main port A
1
1
/
16
"-12 UN
O-ring boss;
SAE J514d
Drain port
9
/
16
"-18 UNF
O-ring boss; SAE J514d
Main port B
1
1
/
16
"-12 UN
O-ring boss;
SAE J514d
Ø101.6
(+0/-0.05)
9.5
R 0.5
Ø14.4
(x2)
Flange S
size 101-2 SAE B
SAE J744c
31
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
F11-006, -010
(SAE versions)
Installation dimensions
CCW CW
68
95
(28)
44
Ø23
8
50
156 max
55
33
8
7
M6x12 min
23
8
43
23
2
Ø4
5/8 UNF-2A
(149)
25°
42
28
M10x16 min
Type S spline shaft
SAE B, 13T, 16/32 DP
(SAE J498b, class 1;
30° involute spline;
flat root, side fit)
Ø20
(+0.009/-0.004)
22.5
Key 6x6x35
Shaft options
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Speed sensor
(optional)
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
Type K key shaft
(Std)
Ø25 (+0.009/-0.004)
Type J key shaft
(Opt.)
Key 8x7x35
3.5
32
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
Installation dimensions
F11-012
(SAE versions)
BA
146
174 max
R 14 (x4)
122
158 max
17
(x2)
Ø24
(x2)
102
53
102
133
101
46
30
Ø55
ccw
cw
29° (x4)
Flange S
size 101-2 SAE B
SAE J744c
Drain port
9
/
16
"-18 UNF
O-ring boss; SAE J514d
Ø14.4
(x2)
Ø101.6
(+0/-0.05)
9.5
R 0.5
Main port A
1
1
/
16
"-12 UN
O-ring boss;
SAE J514d
Main port B
1
1
/
16
"-12 UN
O-ring boss;
SAE J514d
33
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
BA
(58)
(32)
158 max
8
8
33
23
151
50
7
102
72 45
Ø23
M6x12 min
ccw
cw
43
23
2
Ø4
5/8 UNF-2A
8
42
28
M10x16 min
Installation dimensions
F11-012
(SAE versions)
Speed sensor
(optional)
Type S spline shaft
SAE B, 13T, 16/32 DP
(SAE J498b, class 1;
30° involute spline;
flat root, side fit)
Ø20
(+0.009/-0.004)
22.5
Key 6x6x35
Shaft options
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
Type K key shaft
(Std)
Ø25 (+0.009/-0.004)
Type J key shaft
(Opt.)
Key 8x7x35
3.5
34
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
F11-014
(SAE versions)
Installation dimensions
101
46
30
Ø80
Ø24 (x2)
102
17
(x2)
158
max
146
29° (x4)
102
53
120
174 (max)
BA
R 14 (x4)
133
CCW CW
Drain port D
9
/
16
"-18 UNF
O-ring boss; SAE J514d
Type S mountingangeSAE'B'(SAEJ744c)
Drain port C
9
/
16
"-18 UNF
O-ring boss;
SAE J514d
Ø14.5 (x2)
9.5
R 0.5
Main port A
1
1
/
16
"-12 UN
O-ring boss;
SAE J514d
Main port B
1
1
/
16
"-12 UN
O-ring boss;
SAE J514d
Ø101.6 (+0/-0.05)
35
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
F11-014
(SAE versions)
Installation dimensions
Ø80
Ø27
24
33
8
151
158
max
102
45
25°
BA
8
43
23
2
Ø4
5/8 UNF-2A
72
(32)
(58)
CCW CW
Speed sensor
(optional)
Type T key shaft
Size 25-1 (B–B)
(SAE J744c)
Type S spline shaft
SAE B, 13T, 16/32 DP
(SAE J498b, class 1;
30° involute spline;
flat root, side fit)
5
/
16
"-24 UNF-2B
(depth 16)
Key
6.35x6.35x31.8
38.1
2.3
Ø25.4 (+0/-0.05)
28.1
Shaft options
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Tapered key shaft "V"
SAE J744 22-3 (B)
51.6
6.375
25.4
3.2
36
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
F11-019
(SAE version)
Installation dimensions
88
11
63
74
181 max
117
17
54
Ø176 max
29
155
30°
14 R
123
114 max
ccw
cw
Type S mounting flange SAE ‘B’ (SAE J744c)
Approx.
center of
gravity
Flange S
Ø14.4 (x2)
146.1
R 0.8
* O-ring ports according to SAE J514d
Main port A*
(
1
1
/
16
"-12)
Drain port D*
(
9
/
16
"-18)
Drain
port C*
(
9
/
16
"-18)
Main port B*
(
1
1
/
16
"-12)
9.6
Ø101.6
(+0/-0.05)
37
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
2
F11-019
(SAE version)
Installation dimensions
83
110
33
49
(25°)
181 max
8
33
167
5
/
16
"-24 UNF-2b
8
61
65
ccw
cw
Type T key shaft
SAE ‘B-B’ (SAE J744c)
38.1
28.1
(depth 16)
R 1.0
28.3
Key 6.35x6.35x31.8
Ø25.4
(+0/-0.05)
2.3
Shaft options
Make up/Anti cavitation valve
(MUVL or MUVR optional;
clockwise rotation shown)
Type S spline shaft
SAE B, 13T, 16/32 DP
(SAE J498b, class 1;
30° involute spline;
flat root, side fit)
Speed sensor
(optional)
38
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11
Catalogue MSG30-8249/UK
Notes
39
Parker Hannifi n
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
F12
Content
Content Page
Specifi cations ...............................................................................................40
Effi ciency ......................................................................................................41
Noise level ....................................................................................................41
Selfpriming speed and required inlet pressure ............................................. 42
Ordering codes
F12-ISO ........................................................................................................ 43
F12-Cartridge ...............................................................................................44
F12-SAE ....................................................................................................... 45
Installation dimensions ISO
F12-30, -40, -60, -80, -90, -110 and -125 .................................................... 46
F12-152, -162 and -182 ................................................................................48
Installation dimensions Cartridge
F12-30, -40, -60, -80, -90, -110 and -125 ..................................................... 50
Installation dimensions SAE
F12-30, -40, -60, -80, -90, -110 and -125, 4 bolt fl ange ...............................52
F12-152, -162 and -182 ................................................................................54
F12-250 ........................................................................................................56
F12-250 Options (SAE version) ....................................................................57
F12-30, -40, and -60, 2 bolt fl ange ...............................................................58
40
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
Specifications
Frame size F12 -030 -040 -060 -080 -090 -110 -125 -152 -162 -182 -250
Displacement [cm
3
/rev] 30.0 40.0 59.8 80.4 93.0 110.1 125.0 149.8 163.1 179.8 242
Operating pressure
max intermittent
1)
[bar] 480 480 480 480 420 480 480 480 480 480 420
max continuous [bar] 420 420 420 420 350 420 420 420 420 420 350
Motor operating speed [rpm]
max intermittent
1)
8600 6700 5800 5300 5000 4800 4600 4000 4000 4000 3000
max continuous
3)
6700 6100 5300 4800 4600 4400 4200 3700 3700 3700 2700
min continuous 50 50 50 50 50 50 50 50 50 50 50
Max pump selfpriming speed
2)
L or R function; max [rpm] 3150 2870 2500 2300 2250 2200 2100 1700 1600 1500 1500
Motor input flow
max intermittent
1)
[l/min] 219 268 347 426 465 528 575 608 648 728 726
max continuous [l/min] 201 244 317 386 428 484 525 547 583 655 653
Drain temperature
3)
, max [°C] 115 115 115 115 115 115 115 115 115 115 115
min [°C] -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40
Theoretical torque at 100 bar [Nm] 47.6 63.5 94.9 127.6 147.6 174.8 198.4 241 257 289 384.1
Mass moment of inertia
(x10
-3
) [kg m
2
]
1.7 2.9 5 8.4 8.4 11.2 11.2 21 21 21 46
Weight [kg] 11.5 15.7 18.6 25.7 25.7 33 33 40 40 40 77
1) Intermittent: max 6 seconds in any one minute.
2) Selfpriming speed valid at sea level. Find more info on page 42
3) See also installation information. Page 69
41
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
Efficiency_F12_DE.eps
Leif A./020201
100%
90%
80%
0 1000 2000 3000 4000
100%
90%
80%
0 1000 2000 3000 4000
210 bar
420 bar
420 bar
210 bar
Speed
[rpm]
Speed
[rpm]
90
85
80
75
70
65
0 100 200 300
Noise_F12.eps
Leif A./020204
Noise level
[dB(A)]
5000 rpm
3500 rpm
2000 rpm
Pressure
[bar]
Efficiency
Because of its high overall efficiency, driving a motor/
pump from series F12 requires less fuel or electric
power.
Also, it allows the use of a small reservoir and heat
exchanger, which in turn reduce cost, weight,
and installation size.
The diagrams to the right show volumetric and
mechanical efficiencies of an F12-030 motor.
F12-030 motors can be equipped with Power Boost
which in high speed applications can decrease the
mechanical losses by up to 15%, see page 7.
Contact Parker Hannifin for efficiency information on a
particular F12 frame size that is being considered.
Noise level
Series F12 feature low noise levels from low to high
speeds and pressures.
As an example, the diagram to the right shows the
noise level of an F12-030 pump/motor.
The noise level is measured in a semi-anechoic room,
1 m behind the unit.
The noise level for a particular motor/pump may vary
±2 dB(A) compared to what is shown in the diagram.
NOTE: Noise information for F12 frame sizes are
available from Parker Hannifin.
Technical information
Mechanical efficiencies
Volumetric efficiencies
42
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
1000 2000 3000 4000 5000
F12-182 -250 -125 -110 -90 -80 -60 -40 -30
2,0
1,5
1,0
0,5
0
-0,5
F12-162 -152
Inlet pressure
[bar]
0,15 bar vacuum
Speed [rpm]
Inlet pressure
[bar]
Speed [rpm]
Selfpriming speed and required
inlet pressure
Series F12
When operating the F12 as a pump (with L or R valve
plate) above the selfpriming speed, the inlet must be
pressurized. Increased noise and deteriorating perform-
ance may otherwise be experienced.
Diagrams 2 and 3 shows required pump inlet pressure
vs. shaft speed.
The F12 motor (type M valve plate) sometimes operates
as a pump e.g. when used in a propel transmission and
the vehicle is going downhill.
Minimum required inlet pressure versus shaft speed is
shown in the diagrams.
The inlet pressure can be charged by external pump,
pressurized reservoir or using BLA Boost unit.
Find more info about the BLA unit at page 68.
Diagram 2.
Min. required pump (F12-L or -R) inlet press.
Diagram 3. Min. required motor (F12-M) inlet pressure.
Technical information
1000 2000 3000 4000
F12-152-162-182
F12-250 -125 -110 -90 -80 -60 -40 -30
2,0
1,5
1,0
0,5
0
-0,5
0,15 bar vacuum
F12 Motor version
F12 Pump version
43
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
Ordering codes
F12-ISO
x : Available (x): Optional – : Not available
1) F12-110 and -125: Accessory valve block (page 62)
2) Pressure setting on page 63
F12 — — —— — — —
Frame
size
Function
Main
ports
Mounting
flange
Shaft
seal
Shaft
Version
number
Option
page 6, 61
Option
page 7, 67
Frame size 30 40 60 80 90 110 125 152 162 182
Code Function
M Motor x x x x x x x x x x
S Motor, high
speed
(x) (x) (x) - - - - (x) (x) (x)
R Pump,
clockwise
rotation
(x) (x) (x) (x) (x) (x) (x) (x) (x) (x)
L Pump,
counter
clockwise
rot'n
(x) (x) (x) (x) (x) (x) (x) (x) (x) (x)
For other versions, contact Parker Hannifin
Frame size 30 40 60 80 90 110 125 152 162 182
Code Option
0000 Standard x x x x x x x x x x
L130 Flushing valve
1.3 mm orifice
(x) (x) (x) (x) (x) -
1)
-
1)
- - -
MUVR Make up/Anti
cavitation valve
clockwise rotation
(x) - - - - - - - - -
MUVL Make up/Anti
cavitation valve
counter clockwise
rotation
(x) - - - - - - - - -
P__R
2)
Pressure relief valve
clockwise rotation
(x) (x) (x) - - - - - - -
P__L
2)
Pressure relief valve
counter clockwise
rotation
(x) (x) (x) - - - - - - -
Frame size 30 40 60 80 90 110 125 152 162 182
Code Shaft*
D DIN Spline,
Standard
x x x x x x x x x x
A DIN Spline,
Optional
- (x) - - - - - - - -
Z DIN Spline,
Optional
(x) (x) (x) (x) (x) (x) (x) (x) (x) (x)
K Metric key,
Standard
x x x x x x x x x x
J Metric key,
Optional
- (x) - - - - - - - -
H DIN Spline,
Optional
- - - - - - - (x) (x) (x)
G Metric key,
Optional
- - - - - - - (x) (x) (x)
P Metric key,
Optional
(x) - - - - - - (x) (x) (x)
V Tapered shaft (x) (x) (x) - - (x) (x) - - -
*See also dimensional drawings on pages 46 and 48.
Frame size 30 40 60 80 90 110 125 152 162 182
Code Shaft seal
V FPM, high pressure,
high temperature
x x x x x x x x x x
For other versions, contact Parker Hannifin
Frame size
Code Displacem.
(cm
3
/rev)
030 30.0
040 40.0
060 59.8
080 80.4
090 93.0
110 110.1
125 125.0
152 149.8
162 163.1
182 179.8
Frame size 30 40 60 80 90 110 125 152 162 182
Code Main ports
F SAE 6000 psi
flange
x x x x x x x x x x
D SAE 6000 psi
Horizontal
- - - - - - - (x) (x) (x)
A SAE 6000 psi Axial - - - - - - - (x) (x) (x)
K SAE 6000 psi Rear - - - - - - - (x) (x) (x)
M SAE 6000 psi Side - - - - - - - (x) (x) (x)
Frame size 30 40 60 80 90 110 125 152 162 182
Code Mounting flange
I ISO flange x x x x x x x x x x
F ISO 200 flange - - - - - - - x x x
Frame size 30 40 60 80 90 110 125 152 162 182
Code Option
P0 Prepared for speed
sensor
x x x x x x x x x x
PT Prepared for speed
sensor and Painted
Black
(x) (x) (x) (x) (x) (x) (x) (x) (x) (x)
B0 Power Boost and
Prepared for speed
sensor
(x) - - - - - - - - -
BT Power Boost, Pre-
pared for speed
sensor and Painted
Black
(x) - - - - - - - - -
Version number
(assigned for special
versions)
NOTE: All combinations are not valid, please contact
Parker Hannifin
44
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
F12-Cartridge
Ordering codes
F12 — — —— — — —
Frame
size
Function
Main
ports
Mounting
flange
Shaft
seal
Shaft Version
number
Option
page 6, 61
Option
page 7, 67
x : Available (x): Optional – : Not available
1) F12-110 and -125: Accessory valve block (page 62)
2) Pressure setting on page 63
Frame size 30 40 60 80 90 110 125
Code Function
M Motor x x x x x x x
S Motor, high
speed
(x) (x) (x) - - - -
For other versions, contact Parker Hannifin
Frame size 30 40 60 80 90 110 125
Code Shaft*
C DIN Spline, Std. x x x x x x x
K Metric key, Option (x) - (x) (x) (x) (x) (x)
J Metric key, Option - (x) - - - - -
B Spline DIN 5480 - - (x) - - (x) (x)
V Tapered shaft (x) (x) (x) - - (x) (x)
*See also dimensional drawings on page 50.
Frame size 30 40 60 80 90 110 125
Code Shaft seal
V FPM, high pressure,
high temperature
x x x x x x x
For other versions, contact Parker Hannifin
Frame size
Code Displacem.
(cm
3
/rev)
030 30.0
040 40.0
060 59.8
080 80.4
090 93.0
110 110.1
125 125.0
Frame size 30 40 60 80 90 110 125
Code Main ports
F SAE 6000 psi flange x x x x x x x
Frame size 30 40 60 80 90 110 125
Code Mounting flange
C Cartridge x x x x x x x
Version number
(assigned for special
versions)
Frame size 30 40 60 80 90 110 125
Code Option
0000 Standard x x x x x x x
L130 Flushing valve 1.3 mm
orifice
(x) (x) (x) (x) (x) -
1)
-
1)
MUVR Make up/Anti
cavitation valve
clockwise rotation
(x) - - - - - -
MUVL Make up/Anti
cavitation valve
counter clockwise rotation
(x) - - - - - -
P__R
2)
Pressure relief valve
clockwise rotation
(x) (x) (x) - - - -
P__L
2)
Pressure relief valve coun-
ter clockwise rotation
(x) (x) (x) - - - -
Frame size 30 40 60 80 90 110 125
Code Option
P0 Prepared for speed sensor x x x x x x x
PT Prepared for speed sensor
and Painted Black
(x) (x) (x) (x) (x) (x) (x)
B0 Power Boost and Prepared
for speed sensor
(x) - - - - - -
BT Power Boost, Pre pared for
speed sensor and Painted
Black
(x) - - - - - -
NOTE: All combinations are not valid, please contact
Parker Hannifin
45
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
x : Available (x): Optional – : Not available
1) F12-110 and -125: Accessory valve block (page 62)
2) Metric threads
3) Pressure setting on page 63
4) Not in combination with any valve options
Ordering codes
F12 — — —— — — —
F12-SAE
Frame
size
Function Main
ports
Mounting
flange
Shaft
seal
Shaft
Version
number
Option
page 6, 61
Option
page 7, 67
Frame size 30 40 60 80 90 110 125 152 162 182 250
Code Function
M Motor x x x x x x x x x x -
S Motor, high
speed
(x) (x) (x) - - - - (x) (x) (x) -
Q Motor - - - - - - - - - - x
R Pump,
clockwise
rotation
(x) (x) (x) (x) (x) (x) (x) (x) (x) (x) (x)
L Pump,
counter
clockwise
rot'n
(x) (x) (x) (x) (x) (x) (x) (x) (x) (x) (x)
For other versions, contact Parker Hannifin
Frame size 30 40 60 80 90 110 125 152 162 182 250
Code Option
0000 Standard x x x x x x x x x x x
L130 Flushing valve
1.3 mm orifice
(x) (x) (x) (x) (x) -
1)
-
1)
- - - -
MUVR Make up/Anti
cavitation
valve clock-
wise rotation
(x) - - - - - - - - - -
MUVL Make up/Anti
cavitation
valve counter
clockwise
rotation
(x) - - - - - - - - - -
P__R
3)
Pressure
relief valve
clockwise
rotation
(x) (x) (x) - - - - - - - -
P__L
3)
Pressure
relief valve
counter clock-
wise rotation
(x) (x) (x) - - - - - - - -
Frame size 30 40 60 80 90 110 125 152 162 182 250
Code Shaft*
T SAE key,
Standard
x x x x x x x x x x x
R SAE key,
Optional
- - - (x) (x) - - - - - -
S SAE Spline,
Optional
x x x x x x x x x x x
F SAE Spline,
Optional
- - - (x) (x) - - (x) (x) (x) (x)
U SAE Spline,
Optional
- - - (x) (x) - - - - - -
K Metric key,
Standard
- - - - - - - - - - x
D Spline DIN
5480
- - - - - - - - - - (x)
V Tapered
shaft
(x) (x) (x) - - (x) (x) - - - -
*See also dimensional drawings on pages 52 - 59.
Frame size 30 40 60 80 90 110 125 152 162 182 250
Code Shaft seal
V FPM, high pressure,
high temperature
x x x x x x x x x x x
For other versions, contact Parker Hannifin
Frame size
Code Displacem.
(cm
3
/rev)
030 30.0
040 40.0
060 59.8
080 80.4
090 93.0
110 110.1
125 125.0
152 149.8
162 163.1
182 179.8
250 242.0
Frame size 30 40 60 80 90 110 125 152 162 182 250
Code Main ports
S SAE 6000 psi
flange
x x x x x x x - - - -
U SAE UN
threads
4)
(x) (x) (x) (x) (x) (x) (x) - - - -
F SAE 6000 psi
flange
2)
- - - - - - - x x x x
D SAE 6000 psi
Horizontal
2)
- - - - - - - (x) (x) (x) -
A SAE 6000 psi
Axial
2)
- - - - - - - (x) (x) (x) -
K SAE 6000 psi
Rear
2)
- - - - - - - (x) (x) (x) -
M SAE 6000 psi
Side
2)
- - - - - - - (x) (x) (x) -
Frame size 30 40 60 80 90 110 125 152 162 182 250
Code Mounting flange
S SAE 4 bolt x x x x x x x x x x x
R SAE 4 bolt - - - (x) (x) - - - - - -
T SAE 2 bolt x x x - - - - - - - -
Version number
(assigned for special
versions)
Frame size 30 40 60 80 90 110 125 152162182250
Code Option
00 Standard - - - - - - - - - - x
P_ Prepared for speed
sensor
x x x x x x x x x x (x)
B_ Power Boost and
Prepared for speed
sensor
(x) - - - - - - - - - -
_T Painted Black (x) (x) (x) (x) (x) (x) (x) (x) (x) (x) (x)
NOTE: All combinations are not valid, please contact
Parker Hannifin
46
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
F12-30, -40, -60, -80, -90, -110 and -125
(ISO versions)
Installation dimensions
A1
A1
A3
B3
K3
L3
C3
A2
G2
J2
N2
G3
H3
J3
F3
R2
Q2
S2
2)
D3
ØE3 (Tol. k6)
P2
L2
M2
D2
ØE2
ØF2 (tol. h8)
H2
(±0,5)
K2
B2
C2
ØD1 (x4)
B1
C1
T3
ccw
cw
71
97
Ø4
1 1/4˝-12 UNF-2A
62
R2
Ø4
1 1/8˝-12 UNF
Ø4
49
1˝-12 UNF-2A
Type I mounting flange
(ISO 3019/2)
Port E (third drain port)
F12-110 and -125 barrel housing
(ISO /cartridge version)
Port B
Port A
Port D
Type K (P)
Key shaft
2) Type Z has no thread
Port C
1)
F12-80 shown
Speed
sensor
(optional)
Speed
sensor
(optional)
F12-30
only
Type I
flange
See table
Flushing
valve
(optional)
Type D (Z)
spline shaft
1) Port C
Inspection/
drain port
Shaft option D (Z)
Tapered key shaft "V"
SAE J744 32-3 (C)
Tapered key shaft "V"
SAE J744 38-3 (C-C)
Tapered key shaft "V"
SAE J744 44-3 (D&E)
Shaft option V (F12-30) Shaft option V (F12-40) Shaft option V (F12-60)
65.88
85.5
34.92
39.67
Ø38.1
Ø44.45
Ø31.75
Key 7.94x7.94x25.9
Key 9.54x9.54x44.45
Key 11.11x11.11x50.8
30.96
47
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
Spline shaft (DIN 5480)
Key shaft
Installation dimensions
Type K
(std)
Type P
(opt.)
Type J
(opt.)
Type V
(opt.)
F12-30 Ø30 Ø25
3)
- 32-3
-40 Ø30 - Ø35 38-3
-60 Ø35 - - 44-3
-80 Ø40 - - -
-90 Ø40 - - -
-110 Ø45 - - 44-3
-125 Ø45 - - 44-3
Dim.
F12-30 F12-40 F12-60 F12-80
F12-90
F12-110
F12-125
A1 88.4 113.2 113.2 127.2 141.4
B1 118 146 146 158 180
C1 118 142 144 155 180
D1 11 13.5 13.5 13.5 18
A2 100 110 125 135 145
B2 59 65 70 78 85
C2 25 26 22 32 38
D2 8 8 10 12 14
E2 33 42 42 52 58
F2 100 125 125 140 160
G2 172 173 190 216 231
H2 25.5 32.5 32.5 32.5 40.5
J2 50 60 60 70 82
K2 55 52 54 70.5 66.5
L2 40 50 50 56 70
M2 5 5 5 7 6
N2 136.5 137 154 172.5 179
P2 8 8 8 8 8
Q2 28 28 33 36 41
R2
1)
35 35 40 45 50
R2
2)
43 35 35 35 45
S2
1)
M12
x24
M12
x24
M12
x28
M16
x36
M16 x36
S2
2)
- M12
x24
- M12
x28
-
A3 122 134 144 155 170
B3 66 66 66 75 83
C3 23.8 23.8 23.8 27.8 31.8
D3 M12 M12 M12 M16 M16
E3 30 30 35 40 45
F3 33 33 38 43 49
G3 136.5 137 154 172.5 179
H3 23.5 30.5 30.5 30.5 38.5
J3 24 24 28 36 36
K3 50.8 50.8 50.8 57.2 66.7
L3 18 20 20 20 22
T3 - - - - 68
1) Spline shaft type D
2) Spline shaft type Z
3) Max operating pressure 350 bar
Ports
F12-30 F12-40 F12-60 F12-80
F12-90
F12-110
F12-125
A, B
size
3
/
4
"
3
/
4
"
3
/
4
" 1" 1
1
/
4
"
Screw
thread
*)
M10
x20
M10
x20
M10
x20
M12
x20
M14
x26
C
thread
**)
M22
x1.5
M22
x1.5
M22
x1.5
M22
x1.5
M22
x1.5
D
thread
**)
M18
x1.5
M18
x1.5
M22
x1.5
M22
x1.5
M22
x1.5
E
thread
- - - - M22
x1.5
A, B: ISO 6162 *) Metric thread x depth in mm
**) Metric thread x pitch in mm.
Type D (std) Type A Type Z (optional)
F12-30 W30x2x14x9g - W25x1.25x18x9g
3)
-40 W32x2x14x9g W35x2x16x9g W30x2x14x9g
-60 W35x2x16x9g - W32x2x14x9g
-80 W40x2x18x9g - W35x2x16x9g
3)
-90 W40x2x18x9g - W35x2x16x9g
3)
-110 W45x2x21x9g - W40x2x18x9g
3)
-125 W45x2x21x9g - W40x2x18x9g
3)
48
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
F12-152, -162 and -182
(ISO versions)
Installation dimensions
ISO 180
(type I)
ISO 200
(type F)
A1 210 233
B1 210 233
C1 158.4 176.8
D1 158.4 176.8
E1 Ø18 Ø21
A2 180 h8 200 h8
Shaft
G and H
Shaft
D, Z, K and P
B2 50 40
D1
179
101
A2
132
A1
E1
C1
B1
190
127
278
208
8
25
B2
37
82
70
6
M16x2-6H
Ø50k6
25
37
31
25
37
50
45
M16x31
W45x2x21x9g
Thread
M16x2 - 6H (8x)
Depth 27
Main ports
1 1/2" (2x)
Main ports type F
(90 deg Vertical)
Approx. Centre
of gravity
Key
14x9x70
Key
14x9x70
M22x1.5
Case Port D
M22x1.5
Case
Port C
Mounting Flange
ISO 3019
Straight Thread
7/16-20 UNF-2B
Deair and Flushing
Port E
Shaft option P
Shaft option D Shaft options Z and H
Shaft options K and G
39.7
79.4
36.5
18.25
53.4(+0.018/+0.002)
31
70
6
M16x2-6H
Ø45k6
82
48.4
31
45
M16x2-6H
55
W50x2x24x9g
(DIN 5480)
49
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
C
135
99
200
86
233
278
Ø175
101
300
310
163
69
F12-152, -162 and -182
(ISO versions)
Installation dimensions
C
286
200
Ø175
101
237
82
163
109
C
117
163
246
278
99
Ø175
200
Thread
M16x2 - 6H (8x)
Depth 27
Thread
M14x2 - 6H (8x)
Depth 19
Thread
M14x2 -
6H (8x)
Depth 19
Thread
M14x2 - 6H (8x)
Depth 19
Main ports
1 1/2" (2x)
Main ports 1 1/4" (2x)
Main ports 1 1/4" (2x)
Main ports 1 1/4" (2x)
Main ports type A
(180 deg Vertical)
Main ports type D
(90 deg Horizontal)
Main ports type K
(40 deg rear)
Main ports type M
(Side ports)
18.25
36.5
79.4
39.7
66.7
66.7
66.7 (2x)
31.8
31.8
31.8 (2x)
50
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
F12-30, -40, -60, -80, -90, -110 and -125
(Cartridge versions)
Installation dimensions
A4
B4
A5
G5
R5
Q5
ØV5
ØF5 (Tol. h8)
H5
(±0,2)
K5
S5
T5
B5
C5
N5 G6
H6
ØM6
ØN6
ØP6
Q6
L6
A6
B6
C6
K6
R6
P5
C4
T6
E4
ØD4
(x2)
40° (-30, -40,
-60, -110, -125)
43° (-80, -90)
ØE5 (Tol. k6)
J5
D5
L5
M5
ccw
cw
71
97
Ø4
1 1/4˝-12 UNF-2A
62
R2
Ø4
1 1/8˝-12 UNF
Ø4
49
1˝-12 UNF-2A
F12-80 shown
Type C mounting flange
Port E (third drain port)
F12-110 and -125 barrel housing
(ISO /cartridge version)
Port A
Port B
Speed
sensor
(optional)
Port C
1)
Type C
spline
shaft
See table
Type K (J)
key shaft
O-ring
(included)
Flushing
valve
(optional)
Port D
Tapered key shaft "V"
SAE J744 32-3 (C)
Tapered key shaft "V"
SAE J744 38-3 (C-C)
Tapered key shaft "V"
SAE J744 44-3 (D&E)
1) Port C
Inspection/
drain port
Shaft option K (J) Shaft option V (F12-30) Shaft option V (F12-40) Shaft option V (F12-60)
65.88
85.5
34.92
39.67
Ø38.1
Ø44.45
Ø31.75
Key 7.94x7.94x25.9
Key 9.54x9.54x44.45
Key 11.11x11.11x50.8
30.96
51
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
Type K (std) Type J (opt.) Type V (opt.)
F12-30 Ø30 - 32-3
-40 Ø30 Ø35 38-3
-60 Ø35 - 44-3
-80 Ø40 - -
-90 Ø40 - -
-110
Ø45
-
44-3
-125
Ø45
-
44-3
Spline shaft (DIN 5480)
Key shaft
Installation dimensions
Dim.
F12-30 F12-40 F12-60 F12-80
F12-90
F12-110
F12-125
A4 160 200 200 224 250
B4 140 164 164 196 206
C4 188 235 235 260 286
D4 14 18 18 22 22
E4 77 95 95 110 116
A5 100 110 125 135 145
B5 59 65 70 77.5 85
C5 25 26 22 32 38
D5 8 8
1)
10
2)
10 12 14
E5 30 30
1)
35
2)
35 40 45
F5 135 160 160 190 200
G5 127 133 146 157 175
H5 89 92.3 92.3 110.5 122.8
J5 50 60 60 70 82
K5 14 16 15 15 15
L5 40 50 50 56 70
M5 5 5 5 7 6
N5 91 97 110 114 123
P5 22 30 31 40 40
Q5 28 28 28 37 37
R5 35 35 35 45 45
S5 70.5 72 76 91 95.7
T5 15 15 15 15 15
V5 32 35 35 45 45
A6 122 134 144 155 170
B6 66 66 66 75 83
C6 23.8 23.8 23.8 27.8 31.8
G6 91.5 97 110 114 123
H6 69.5 71 74 89.5 93.7
K6 50.8 50.8 50.8 57.2 66.7
L6 16 18 18 20 20
M6 92 115 115 130 140
N6 110 127 135 154 160
P6 128.2 153.2 153.2 183.2 193.2
Q6 5 5 5 5 5
R6 5 5 5 5 5
T6 - - - - 68
1) Key shaft type K
2) Key shaft type J (opt.).
Ports
F12-30 F12-40 F12-60 F12-80
F12-90
F12-110
F12-125
A, B
size
3
/
4
"
3
/
4
"
3
/
4
" 1" 1
1
/
4
"
Screw
thread
M10
x20
M10
x20
M10
x20
M12
x22
M14
x26
C
thread
M14
x1.5
M14
x1.5
M14
x1.5
M14
x1.5
M14
x1.5
D, E
thread
M18
x1.5
M18
x1.5
M22
x1.5
M22
x1.5
M22
x1.5
A, B: ISO 6162
Type C (standard) Type B (optional)
F12-30 W30x2x14x9g -
-40 W30x2x14x9g -
-60 W30x2x14x9g W35x2x16x9g
-80 W40x2x18x9g -
-90 W40x2x18x9g -
-110 W40x2x18x9g W45x2x21x9g
-125 W40x2x18x9g W45x2x21x9g
O-ring dimensions
F12-30 127x4
-40 150x4
-60 150x4
-80 180x4
-90 180x4
-110 190x4
-125 190x4
52
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
F12-30, -40, -60, -80, -90, -110 and -125
(SAE versions with 4 bolt flange)
Installation dimensions
A7
A7
ØD7 (x4)
B7
C7
T9
A8
G8
J8
N8
L8
M8
D8
ØE8
ØF8
H8
K8
B8
C8
A9
B9
K9
L9
C9
G9
H9
J9
F9
R8
Q8
D9
ØE9
ccw
cw
71
97
Ø4
1 1/4˝-12 UNF-2A
62
R2
Ø4
1 1/8˝-12 UNF
Ø4
49
1˝-12 UNF-2A
Shown: F12-80 with
4 bolt flange
Type S (SAE 4 bolt) mounting flange
Port E (third drain port)
F12-110 and -125 barrel housing
(SAE version)
Port A
Port B
Port C
1)
Speed
sensor
(optional)
Speed
sensor
(optional)
F12-30
only
Type S
flange
See
table
Type S (U)
spline shaft
Type T key shaft
Flushing
valve
(optional)
Port D
1) Port C
Inspection/
drain port
Shaft option S (U)
Tapered key shaft "V"
SAE J744 32-3 (C)
Tapered key shaft "V"
SAE J744 38-3 (C-C)
Tapered key shaft "V"
SAE J744 44-3 (D&E)
Shaft option V (F12-30) Shaft option V (F12-40) Shaft option V (F12-60)
65.88
85.5
34.92
39.67
Ø38.1
Ø44.45
Ø31.75
Key 7.94x7.94x25.9
Key 9.54x9.54x44.45
Key 11.11x11.11x50.8
30.96
53
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
Mounting flange (SAE J744)
Installation dimensions
Dim.
F12-30 F12-40 F12-60 F12-80
F12-90
F12-110
F12-125
A7 89.8 114.5 114.5 114.5 161.6
B7 118 148 148 155 204
C7 118 144 144 155 200
D7 14 14 14 14 21
A8 100 110 125 135 145
B8 59 65 70 77.5 85
C8 25 26 22 32 38
D8 6.35 7.94 7.94 9.53 11.1
E8 33 42 42 52 57.5
F8 101.60/
101.55
127.00/
126.94
127.00/
126.94
127.00/
126.94
152.40/
152.34
G8 189.5 197 214 240 264
H8 8 8 8 8 8
J8 38 48 48 54 67
K8 72 76 79 95 99
L8 31.8 38.1 38.1 44.5 54.1
M8 2.5 4 4 4 7.5
N8 153.5 161 178.3 197.1 212
Q8
1)
26 27 27 29 39
Q8
2)
- - - 23 -
R8
1)
33 48 48 54 66.7
R8
2)
- - - 48 -
A9 122 134 144 155 170
B9 66 66 66 75 83
C9 23.8 23.8 23.8 27.8 31.8
D9*
5
/
16
"-24
3
/
8
"-24
3
/
8
"-24
1
/
2
"-20
5
/
8
"-18
E9 25.40/
25.35
31.75/
31.70
31.75/
31.70
38.10/
38.5
44.45/
44.40
F9 28.2 35.3 35.3 42.3 49.4
G9 153.8 161 178.3 197.1 212
H9 9.7 12.7 12.7 12.7 12.7
J9 16 19 19 26 32
K9 50.8 50.8 50.8 57.2 66.7
L9 18 20 20 20 22
T9 - - - - 68
* UNF-2B thread
1) Spline shaft type S
2) Spline shaft type U
3) Max operating pressure 350 bar
Main ports A and B, type U (optional)
F12-30 1
1
/
16
" - 12 UN
3)
F12-40 1
5
/
16
" - 12 UN
3)
F12-60 1
5
/
16
" - 12 UN
3)
F12-80 1
5
/
16
" - 12 UN
3)
F12-90 1
5
/
16
" - 12 UN
3)
F12-110 1
5
/
8
" - 12 UN
3)
F12-125 1
5
/
8
" - 12 UN
3)
Ports
F12-
30
F12-
40
F12-
60
F12-80
F12-90
F12-110
F12-125
A, B size
3
/
4
"
3
/
4
"
3
/
4
" 1" 1
1
/
4
"
Screw
thread
**)
3
/
8
"-16
x22
3
/
8
"-16
x20
3
/
8
"-16
x22
7
/
16
"-14
x27
1
/
2
"-13
x25
C thread
7
/
8
"-14
7
/
8
"-14
7
/
8
"-14
7
/
8
"-14 1
1
/
16
"-12
D thread
3
/
4
"-16
3
/
4
"-16
7
/
8
"-14
7
/
8
"-14 1
1
/
16
"-12
E thread
- - - - 1
1
/
16
"-12
A, B: ISO 6162 C, D, E: O-ring boss (SAE J514)
**) UN thread x depth in mm.
S (standard) R (optional)
F12-30 SAE'B',4bolt -
-40 SAE'C',4bolt -
-60 SAE'C',4bolt -
-80 SAE'C',4bolt SAE ’D’, 4 bolt
-90 SAE'C',4bolt SAE ’D’, 4 bolt
-110 SAE'D',4bolt -
-125 SAE'D',4bolt -
Spline shaft (SAE J498b, class 1, flat root, side fit)
S (standard) U (opt.) F (optional)
F12-30 SAE'B'
13T, 16/32 DP
- -
-40 SAE'C'14T,
12/24 DP
- -
-60 SAE'C'14T,
12/24 DP
- -
-80 SAE'C-C'
17T, 12/24 DP
SAE'C'
14T,12/24DP
3)
SAE'D'
13T, 8/16 DP
-90 SAE'C-C'
17T, 12/24 DP
SAE'C'
14T,12/24DP
3)
SAE'D'
13T, 8/16 DP
-110 SAE'D'
13T, 8/16 DP
- -
-125 SAE'D'
13T, 8/16 DP
- -
Key shaft (SAE J744)
F12 T (standard) R (optional) V (optional)
-30 SAE'B-B'
(Ø25.4 mm/1")
-
32-3
-40 SAE'C'
(Ø31.75 mm/1
1
/
4
")
-
38-3
-60 SAE'C'
(Ø31.75 mm/1
1
/
4
")
- 44-3
-80 SAE'C-C'
(Ø38.1 mm/1
1
/
2
")
SAE ’D’
(Ø44.45 mm /1
3
/
4
")
-
-90 SAE'C-C'
(Ø38.1 mm/1
1
/
2
")
SAE ’D’
(Ø44.45 mm /1
3
/
4
")
-
-110 SAE'D'
(Ø44.45 mm/1
3
/
4
")
- 44-3
-125 SAE'D'
(Ø44.45 mm/1
3
/
4
")
- 44-3
54
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
Ø57 min
8
54
R4
R4
35
Installation dimensions
F12-152, -162 and -182
(SAE versions)
139
135
303
233
8
Ø21 (4x)
205
190
179
101
Straight Thread
7/16-20 UNF-2B
Deair and Flushing
Port E
Straight Thread
1-1/16-12UN-2B
Case Port C
Approx. Centre
of gravity
Straight Thread
1-1/16-12UN-2B
Case Port D
Thread
M16x2 - 6H (8x)
Depth 27
Main ports
1 1/2" (2x)
Mounting Flange Code S
SAE J744 Size 152-4 (D)
Shaft option FShaft option SShaft option T
Main ports type F
(90 deg Vertical)
Ø152.4 (+0/-0.05)
Ø152.4 (+0/-0.05)
102.5
12.7
79.4
161.6
80.8
199.6
39.7
R0.8
161.6
36.5
18.25
6.7
49.3
Ø44.45
(+0/-0.05)
Ø43.713 (+0/-0.13)
Ø50.06 (+0/-0.13)
Key
11.11x11.11x54
5/8-18 UNF
depth 30
5/8-11 UNC
depth 35
5/8-11 UNC
depth 30
12.7
66.7
66.7
66.7
R0.8
34.7
SAE'D';13T,
8/16 DP
class 1, flat root
side fit
Type T
key shaft
SAE'D'
(SAE J744c)
SAE J498b
15T-8/16 DP
55
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
101
325
334
163
69
C
311
200
Ø175
261
82
163
101
109
C
270
302
163
117
99
Ø175
200
C
135
99
200
258
303
86
Ø175
Thread
M16x2 - 6H (8x)
Depth 27
Thread M14x2 - 6H (8x)
Depth 19
Thread
M14x2 - 6H (8x)
Depth 19
Thread
M14x2 - 6H (8x)
Depth 19
Main ports
1 1/2" (2x)
Main ports
1 1/4" (2x)
Main ports 1 1/4" (2x)
Main ports 1 1/4" (2x)
Installation dimensions
F12-152, -162 and -182
(SAE versions)
Main ports type A
(180 deg Vertical)
Main ports type D
(90 deg Horizontal)
Main ports type K
(40 deg rear)
Main ports type M
(Side ports)
79.4
39.7
18.25
36.5
66.7
31.8
66.7
66.7(2x)
31.8
31.8 (2x)
56
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
232 max
101
141
336
200
max
M16x35
(x8)
197 118
79
24
27
200 max
Ø21
(x4)
180
395
216
ccw
cw
F12-250
(SAE version)
Installation dimensions
Approx.
center of
gravity
Type S mounting flange
SAE ‘D’ (SAE J744c)
* 6000 psi flange (SAE J518c)
161.6
161.6
R0.8
12.7
7.9
36.5
79.38
Main port A*
(
1
1
/
2
")
Main port B*
(1
1
/
2
")
Drain port D
(
BSP
3
/
4
")
Drain
port C
(
BSP
3
/
4
")
Ø152.4
(+0/-0.05)
Plugged
with
steel plug
57
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
F12-250 Options (SAE version)
Installation dimensions
16
M16x31min
Ø57
min
82
R1
max.
6
57 min
Ø20
5/8-11 UNCx36 min
M16x31min
48
R4
55
R4
R4
35
197 118
53.5
Key
14x9x70
Type K key shaft
(metric; not SAE)
Type T key shaft
(SAE key)
56.3
34.7
66.7
66.7
49.6
(0/-0.16)
79.4
Ø57.5
Ø57.5 Ø57.5
136.5
76.2
R1.6 max
Ø50
(+0.018/+0.002)
12.7x12.7x76.2
Ø50.8
(+0.011/-0.005)
Ø50.06 (0/-0.13)
Ø43.713 (0/-0.13)
Type S spline shaft
SAE J498b, class 1;
30° involute spline;
13T-8/16 DP;
flat root, side fit
Type F spline shaft
SAE J498b, class 1;
15T-8/16 DP;
fillet root, side fit
Speed sensor
(optional)
Shaft option D Shaft option SShaft option F
Shaft option T
Shaft option K
Type D spline shaft
W50x2x24x9g
DIN 5480 side fit
Plugged
with
steel plug
58
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
F12-30, -40, and -60
(SAE versions with 2 bolt flange)
Installation dimensions
ØD10
(x2)
A10
B10
G11
J11
D11
A11 B11
C11
N11
L12
A12
B12
C12
G12
H12
K12
J12
F12
D12
ØE12
L11
M11
ØE11
ØF11
K11
H11
R11
Q11
F10
E10 R
C10 R
ccw
cw
62
R2
Ø4
1 1/8˝-12 UNF
Ø4
49
1˝-12 UNF-2A
71
97
Ø4
1 1/4˝-12 UNF-2A
Port A
Port B
Port D
Flushing
valve
(optional)
Type T
key shaft
Type T
flange
Speed
sensor
(optional)
F12-30
only
1) Port C
Inspection/
drain port
Port C
1)
Type T (SAE 2 bolt) mounting flange
Shown: F12-60 with 2 bolt flange
See
table
Type S
spline shaft
Shaft option S
Tapered key shaft "V"
SAE J744 32-3 (C)
Tapered key shaft "V"
SAE J744 38-3 (C-C)
Tapered key shaft "V"
SAE J744 44-3 (D&E)
Shaft option V (F12-30) Shaft option V (F12-40) Shaft option V (F12-60)
65.88
85.5
34.92
39.67
Ø38.1
Ø44.45
Ø31.75
Key 7.94x7.94x25.9
Key 9.54x9.54x44.45
Key 11.11x11.11x50.8
30.96
59
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F12
Catalogue MSG30-8249/UK
3
Installation dimensions
Dim.
F12-30 F12-40 F12-60
A10 146 181 181
B10 176 215 215
C10 63 74 74
D10 14.4 17.5 17.5
E10 10 16 16
F10 10 15.5 15.5
A11 100 110 125
B11 59 65 70
C11 25 26 22
D11 6.35 7.94 7.94
E11 33 42 42
F11 101.60/
101.55
127.00/
126.95
127.00/
126.95
G11 189.5 197 214
H11 8 8 8
J11 38 48 48
K11 71 77 81.5
L11 31.8 38.1 38.1
M11 2.5 4 4
N11 154 161 178.5
Q11 26 27 27
R11 33 48 48
A12 122 134 144
B12 66 66 66
C12 23.8 23.8 23.8
D12
1) 5
/
16
"-24
3
/
8
"-24
3
/
8
"-24
E12 25.40/
25.35
31.75/
31.70
31.75/
31.70
F12 28.2 35.2 35.2
G12 154 161 178.5
H12 9.7 12.7 12.7
J12 16 19 19
K12 50.8 50.8 50.8
L12 18 20 20
1) UNF-2B thread
6) Max operating pressure 350 bar
Ports
F12-30 F12-40 F12-60
A, B size 19 (
3
/
4
") 19 (
3
/
4
") 19 (
3
/
4
")
Screw
thread
*)
3
/
8
"-16
x22
3
/
8
"-16
x20
3
/
8
"-16
x22
C thread
3
/
4
"-16
3
/
4
"-16
7
/
8
"-14
D thread
3
/
4
"-16
3
/
4
"-16
7
/
8
"-14
A, B (main ports): SAE J518c (6000 psi)
C, D (drain ports): O-ring boss (SAE J514)
*) UN thread
Main ports A and B, type U (optional)
F12-30 1
1
/
16
" - 12 UN
6)
-40 1
5
/
16
" - 12 UN
6)
-60 1
5
/
16
" - 12 UN
6)
O-ring ports according to SAE J514d
Mounting flange T (SAE J744)
F12-30 SAE'B',2bolt
-40 SAE'C',2bolt
-60 SAE'C',2bolt
Spline shaft S
(SAE J498b, class 1, flat root, side fit)
F12-30 SAE'B'
13 T; 16/32 DP
-40 SAE'C'
14 T; 12/24 DP
-60 SAE'C'
14 T; 12/24 DP
Key shaft (SAE J744)
T (Standard) V (optional)
F12-30 SAE'B-B'
Ø25.4 mm/1"
32-3
-40 SAE'C'
Ø31.75 mm/1
1
/
4
"
38-3
-60 SAE'C'
Ø31.75 mm/1
1
/
4
"
44-3
60
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Accessories
Accessories
Content Page
Flushing valves for F12 motors .....................................................................61
FV13 flushing valve block .............................................................................62
Integrated pressure relief valve ....................................................................63
Possible pressure settings ............................................................................ 63
SR pressure relief anti-cavitation valve ........................................................64
SV pressure relief valve ................................................................................ 65
SV pressure relief valve, Dimensions ...........................................................66
Speed sensor ...............................................................................................67
BLA Boost Units ...........................................................................................68
61
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
4
20
Q [l/min]
20
16
16
12
12
8
8
4
4
0
0 Δp [bar]
Ø1,3 mm
Flow versus pressure differential (port A or B to tank).
General information
The integrated flushing valve supplies the motor with a
cooling flow through the case which may be required
when operating at high speeds and power levels.
In a closed loop hydrostatic transmission the flushing
valve secures that cool fluid from the charge circuit is
constantly added to the main circuit.
The flushing valve consists of a ’three-position’, three-
way spool valve which connects the low pressure side
of the main hydraulic circuit with the motor case. The
valve opens at a pressure differential between port A
and port B of approximately 14 bar.
In order to limit the flow, a nozzle with a orifice is avail-
able from Parker Hannifin. The diagram to the right
shows flow versus differential pressure.
For general advise when flushing might be needed,
see page 67.
Hydraulic schematic.
F12_60_FV_install.eps
Leif A./03-01-27
Built-in
flushing
valve
Nozzle
Ø1.3 mm
Orifice size
(No nozzle)
F12_FV_schem.eps
Leif A./03-01-27
Port A
Port B
Integrated flushing valve
(F12-30, -40, -60, -80, -90)
Nozzle
Ø1.3 mm
Flushing valves for F12 motors
Ordering code
F12 – 080 – MF – IV – K –
000
– L130 – P0
Standard F12 ordering code
(for F12-30, -40, -60, -80, -90)
NOTE: FV13 flushing valve block for
F12-110 shown on next page.
Integrated flushing valve (F12-30, -40, -60, -80, -90)
Code
Nozzle designation
L 130 1.3 mm
62
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Code
Nozzle
L 130
Ø1.3 mm
Code Techn. status
A
Factory assigned
Code Seals
H
Nitrile rubber
Code
Size (SAE 6000 psi)
3
1¼" (for F12-110 / -125)
Code Version
1
Factory
assigned
Flushing
valve
F12_110_FV13_view.eps
Leif A./03-01-27
FV13 valve block
Restrictor nozzle
F12-110 motor
FV13 flushing valve block (for F12-110, -125)
The FV13 for the F12-110 / -125 motor has the same
function as the integrated flushing valve for the other
F12 frame sizes. The valve block mounts between the
motor port flange and the split-flange tube/hose connec-
tors utilizing ’long’ mounting screws (screw size M14x75
or
1
/
2
"-13 UNC based on split-flange height as shown
below).
The FV13 flushing valve kit contains the required O-
rings (shown below) but no screws, split-flanges or tube/
hose connectors.
FV13 installation
FV13 restrictor nozzles
When required, a nozzle is utilized to restrict the flow
through the F12-110, -125 motor case. The nozzle
installs in the drilled and tapped (M10x1.0) drain line
located in the valve block as shown to the left. The
diagram on page 61 shows flushing flow versus dif-
ferential pressure for selected orifice sizes.
The following table lists currently available nozzles
and the corresponding FV13 ordering code designa-
tion.
Hydraulic schematic.
F12_FV13_schem.eps
Leif A./03-01-27
Port A
Port B
Nozzle Ø1.3 mm
FV13 flushing valve block
(27)
25
47
92
44
38
83
142
7
φ 32
(x2)
FV13_install.eps
Leif A./03-01-27
Nozzle
Weight:
2.9 kg
15.5 dia. (x8)
Tube/hose
connector
Split
flange
FV13 valve
block
O-ring
29.2x3.0
O-ring
37.69x3.53 (x2)
31.8
66.7
Flushing valves for F12 motors
FV13_squares.eps
Leif A./03-01-28
FV13 Ordering code
FV 1 3 – H – A – L130
Valve Version Size Seals Techn. Nozzel
type status
Designation Flushing valve
Part number
Orifice
size [mm]
Orifice
Part number
L000 no nozzle 3780292
L130 (std.) 3795623 1.3 379 4413
63
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
4
Port A
Port B
Pressure relief valve for F12-motors
Diagram for PLC082 pressure relief valves integrated in F12-030
∆p (bar) Pressure override characteristic
q (l/min)
300
500
400
100
200
0
0255075 100
Diagram for PLC182 pressure relief valves integrated in F12-040 and F12-060
∆p (bar) Pressure override characteristic
q (l/min)
25 12550 15075 175100 200
100
0
0
200
300
400
500
Integrated pressure relief valve
( F12-030, -040, -060 )
Integrated pressure relief valves are available for
F12-030, F12-040 and F12-060. These are designed
to protect the motor from short duration pressure
spikes. The motor could be ordered with non-adjustable
pressure setting between 210 - 420 bar. The motor
has to be ordered as unidirectional, L or R, and this is
specified in the ordering code as example below.
F12-030-MS-SV-S-000-P28L-P0
P=Pressure relief valve, 28 = 280 bar, L = left
Possible pressure settings
Code Pressure
bar
21 210
23 230
25 250
28 280
30 300
33 330
35 350
38 380
40 400
42 420
64
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Code Serial number
00
Factory assigned
Code
Port size (SAE 6000 psi)
1
3
/
4
" for:
F12-30, -40, -60
2
1" for:
F12-80, -90
3
1¼" for:
F12-110 , -125
Pressure relief/
make-up valve
block
SR pressure relief anti-cavitation valve
The SR pressure relief/make-up valve block for series
F12 motors is designed to protect the motor and the
main hydraulic lines from short duration pressure spikes.
The valve block also provides an excellent make-up
function.
The valve block installs directly on the motor port flange,
and is available in 3 sizes:
1
3
/
4
" for F12-30/-40/-60
2 1" for F12-80, -90
3 1¼" for F12-110 , -125
The SR valve block consists of a housing containing two
high pressure relief cartridges and two separate check
valves for anti-cavitation. Cartridges are available in non-
adjustable pressure settings between 280 and 420 bar
(4 000 and 6000 psi respectively).
A make-up port (G) is also provided. In certain operating
conditions, the motor (when operating as a pump) may
cavitate because of insufficient inlet pressure.
To prevent this, the G port should be pressurized.
Contact Parker Hannifin for further information.
Thepressuredropthroughthemainports(A–A'or
B–B')islow.Asanexample,thepressuredropon
size 1 (
3
/
4
") is 0.45 bar (6.5 psi) at 175 l/min, and on
size 2 (1") 0.7 bar (10 psi) at 250 l/min.
NOTE: The valve block includes main port O-rings
(facing the motor) but no mounting screws.
SR valve block location.
SR valve block schematic.
F12_SR_schem_SE.eps
Leif A./03-01-27
Port B
Port A
Port G
SR valve block F12 motor
F12_SR_install.eps
Leif A./03-01-31
Port G
SR valve block
Pressure relief/anticav. valve for F12-motors
SR_SV_squares.eps
Leif A./03-01-29
Ordering code
SR 1 – / – 00 – H F – A
Valve Version Port Serial Seals Threads Techn.
function size Pressure settings number status
Code Version
1
Factory assigned
Code
Pressure settings (A/B ports) [bar]
280, 300, 330, 350, 380, 400 or 420
Code Seals
H
Nitrile rubber
Code
Threads (port G)
F
Metric
Code Techn. status
A
Factory assigned
65
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
4
Pressure relief/anticav. valve for F12-motors
SV pressure relief valve
General information
The SV pressure relief valve block for series F12 motors
is designed to protect the motor and adjacent hydraulic
components from short duration pressure peaks.
It installs directly on the motor port flange and is
available in two sizes:
’1’:
3
/
4
" for F12-30/-40/-60
’2’: 1" for F12-80/ -90
The valve block consists of a housing containing two
high pressure relief cartridges with anti-cavitation func-
tion. Cartridges are available in non-adjustable pressure
settings between 280 and 420 bar.
A make-up/drain port, L, is also provided. In certain
operating conditions the motor may cavitate because of
in-sufficient inlet pressure. To prevent this, the L port can
be pressurized. When there is a risk of over-heating, the
L port can also be utilized to take out part of the flow for
cooling. Contact Parker Hannifin for further information.
Thepressuredropthroughthemainports(A–A'or
B–B')islow.Asanexample,thepressuredropon
size 1 (
3
/
4
") is 0.45 bar (6,5 psi) at 175 l/min (45 gpm),
and on size 2 (1") 0.7 bar (10 psi) at 250 l/min (65 gpm).
NOTE: - The valve block includes main port O-rings
(facing the motor) but no mounting screws.
- The valve blocks can be used on all versions
of series F12 motors.
SV valve block installed on an F12 motor.
Hydraulic schematic.
F12_80_SV_install.eps
Leif A./03-01-31
SV pressure relief
valve block
F12_SV_schematic.eps
Leif A./03-01-29
(F12)
SV valve block Port B’
Port L Port A’
Port A
Port B
CLM
D
E
F
A
φ P
(x6)
K
G
H
B
J
SR11_install.eps
Leif A./03-01-27
Check
valve
Relief
valve
cartridge
Facing
the motor
Ports
A/A’
Ports
B/B’
N
thread
Port L
Port G
(size 1 and 2)
M22x1.5; min 16 deep
Dim.
[mm]
Size 1
(
3
/
4
")
Size 2
(1")
Size 3
(1¼")
A 55 57
57
B 55 55
25
C 32 32
26
D 157 160
160
E 66 75
83
F 23.8 27.8
31.8
G 50.8 57.15
66.7
H 103 109
88
J 140 150
135
K 18 18
-
L 18 18
18
M 78.5 80
-
N M10
x18
M12
x20
M14
x23
P 11 13
15.5
Weight Size 1
(
3
/
4
")
Size 2
(1")
Size 3
(1¼")
[kg] 7.4 9.1
8.5
SR pressure relief anti-cavitation valve, Dimensions
66
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Pressure relief
valve
SV_install.eps
Leif A./03-01-27
A
B
F
E
G
φ K (x8)
H
J
D
C
Facing
the motor
Port BPort A
Make-up port L
(M22x1.5)
Port A Port B
relief valve cartr.
Ordering code
SR_SV_squares.eps
Leif A./03-01-29
SV 1 – / – 00 – H F – A
Valve Version Port Serial Seals Threads Techn.
function size Pressure setting number (port L) status
Dim. [mm] SV11 SV12
A 71 73
B 31 31
C 36 41
D 47 51
E 130 127
F 66 75
G 23.8 27.8
H 50.8 57.2
J 99 109
K 11 13
Weight [kg] 4.2 5.0
Code
Port size (SAE 6000 psi)
1
3
/
4
"
F12-30, -40, -60
2
1"
F12-80, -90
Code Version
1
Factory assigned
Code
Pressure settings (A/B ports) [bar]
280, 300, 330, 350, 380, 400 or 420
Code Serial number
00
Factory assigned
Code Seals
H
Nitrile rubber
Code
Threads (port L)
F
Metric
Code Techn. status
A
Factory assigned
SV pressure relief valve, Dimensions
67
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
4
F12_speed_sensor.eps
Leif A./020204
Speed
sensor
A speed sensor kit is available for series F11/F12.
A ferrostat differential (Hall-effect) sensor installs in
a separate, threaded hole in the F11/F12 bearing
housing .
On F12 the speed sensor is directed towards the ring
gear. On F11 the speed sensor is directed towards the
pistons. The sensor output is a 2 phase shifted square
wave signal within a frequency range of 0 Hz to 15 kHz.
NOTE: - The motor bearing housing must be
prepared for the speed pick-up;
refer to the F11/F12 ordering codes on
pages 12-14(F11) and 43-45 (F12).
- On F11 the pistons position must be
known before mounting.
- Additional information is provided in the
marketing information MSG30-8302/UK.
- The speed sensor is also shown in the
illustrations on pages 17 to 37 and 46 to 59.
Part number for Speed sensor is 3783883.
Speed sensor
F12 with speed sensor.
F11-14 with speed sensor.
Speed
sensor
68
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Catalogue MSG30-8249/UK
Hydraulic motor/pump
BLA Boost units Series F11/F12
BLA
General information
The BLA boost unit simplifies the building of closed or
semi-closed hydrostatic transmissions.
Main features are:
• Replacesconventionalchargepumpand
corresponding valves in many applications
• Allowspumpspeedsabovenormalselfpriming
speed
• Suitableforsystemowratesto400l/min
• Includeslter
• Simpleconstruction-nomoving/wearparts
• Cost-effectiveinstallation
• Smalltanksize
• Helpsinbuildingalow-costhydrostatic
transmission.
Typical applications:
• Fandrives
• Propellerdrives
• Generatordrives
• Pumpdrives
Description
In a closed circuit hydrostatic transmission, a charge
pump is normally included with the main pump, pro-
viding make-up fluid which replaces pump and motor
volumetric losses. It also maintains sufficient pump inlet
pressure to avoid cavitation.
The BLA boost unit replaces the charge pump in many
applications, when the following conditions are met:
- The max-to-min pump flow ratio does not exceed 2:1
- System pressure changes gradually without frequent
and pronounced pressure peaks
- The line length between pump and boost unit is
relatively short.
There are two basic sizes of the BLA boost unit:
- BLA 4 (to 160 l/min pump flow)
- BLA 6 (to 400 l/min pump flow).
The main part of the unit is an aluminium housing
with a built-in nozzle and an injector; refer to the cross
section to the right.
When fluid flows from the motor outlet port through
the unit and to the pump inlet port, the increased fluid
velocity between the nozzle and injector creates a low
pressure zone causing additional fluid to be drawn from
tank into the main circuit.
Also, pressure increases after the injector, allowing the
pump to be operated at speeds higher than the self-
priming speed. The ’boost pressure’ increases with flow.
The housing includes ports that should be connected to
the pump and motor drain ports respectively.
An additional bleed-off nozzle diverts approx. 10% of
the main flow through the cartridge filter before being
directed to the tank.
Oil cooling
An oil cooler is usually required in the hydraulic system,
in order to remove the heat that is generated in the
main circuit. A full-flow oil cooler should be installed in
the return line between the motor and the boost unit.
BLA boost unit cross section.
1
4
3
5
6
7
2
BLA_install.eps
Leif A./02-01-03
1. Pump
2. Motor
3. Boost unit (with injector
and nozzle
4. Filter cartridge
5. Pressure relief valve
6. Full-flow filter (when
required
7. Reservoir
Boost unit installation
For more information please see our technical
catalogue BLA boost unit MSG30-8224/UK
BLA_cross_section.eps
Leif A./02-01-03
Injector From Nozzle
tank
To
pump
inlet
From
motor
outlet
Bleed-off
nozzle
To
filter
From filter
to tank
BLA Boost Units
69
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
5
Series F12
Series F11
Clockwise rotation
Port A Port B
Counter
clockwise
rotation
Direction of rotation
The motor versions are bi-directional.
The pump versions are uni-directional, allowing higher
selfpriming speeds (refer to pages 9, 11 and 40, 42).
The illustration to the right shows direction of flow ver-
sus shaft rotation. In a motor application, the shaft turns
clockwise when port B (black arrow) is pressurized, and
counter clockwise when port A (open arrow) is pressu-
rized.
In a pump application where the shaft turns clock-wise,
port B is the inlet port and should be connected to tank;
when the shaft turns counter clockwise, port A is the
inlet port.
Hydraulic fluids
Ratings and performance data for series F11/F12 are
based on operating with good quality, contamination-
free, petroleum-based fluids.
Hydraulic fluids type HLP (DIN 51524), automatic
transmission fluids type A, or API CD engine oils can be
used.
Fire resistant fluids (when used under modified operat-
ing conditions) and synthetic fluids may also be suitable.
Operating temperature
The following temperatures should not be exceeded
(type V FPM shaft seals):
Main circuit 80 °C
Drain circuit: 115 °C.
NBR shaft seals (type N) can be used to
90 °C drain fluid temperature.
NOTE: The temperature should be measured at
the utilized drain port.
Continuous operation may require case flushing in order
to meet the viscosity and temperature limitations.
The following table shows operating speeds, above
which flushing is usually required, as well as suggested
flow through the case.
F11/F12 in series operation
When running F11/F12 in series at higher pressure
levels,
Please contact Parker Hannifin for further information.
NOTE:
When operating the F11/F12 as a pump above
the selfpriming speed (valid for both the pump and
motor versions), the inlet must be sufficiently pres-
surized. Increased noise and deteriorating perform-
ance may otherwise be experienced.
For further information refer to ’Selfpriming speed
and required inlet pressure’ on pages 11 and 42.
Installation information
Frame size Speed [rpm] Flow [l/min]
F11-5 5500 1 - 2
F11-6 4500 2 - 3
F11-10 4500 2 - 3
F11-12 4500 2 - 3
F11-14 4500 2 - 3
F11-19 4000 2 - 4
Frame size Speed [rpm] Flow [l/min]
F12-30 3500 4 - 8
F12-40 3000 5 - 10
F12-60 3000 7 - 14
F12-80 2500 8 - 16
F12-90 2500 8 - 16
F12-110 2300 9 - 18
F12-125 2300 9 - 18
F12-152/162/182 2200 10 - 20
F12-250 1800 12 - 22
70
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
Installation information
Viscosity
The ideal operating range is15 to 30 mm
2
/s [cSt].
At operating temperature, the viscosity (of the drain
fluid) should be kept above 8 mm
2
/s [cSt].
At start-up, the viscosity should not exceed
1000 mm
2
/s [cSt]
Filtration
To obtain the highest service life of the F11/F12,
the fluid cleanliness should meet or exceed
ISO code 20/18/13 (ISO 4406).
During normal operating conditions, a 10 µm (absolute)
filter is recommended.
Case pressure
The service life of the shaft seal ring is affected by the
speed of the motor and the case drain pressure and
it can decrease with an increase in the frequency of
pressure peaks.
Note, seal life can be shorter at unfavourable operating
conditions (high temperature, low oil viscosity, contami-
nated oil).
The table below shows recommended case pressure
as a function of shaft speed.
The case pressure must be equal to or greater than the
external pressure on the shaft seal ring.
To secure correct case pressure and lubrication, a
spring loaded check valve, 1-3 bar, in the drain line
(shown on next page) is recommended.
Note.
Contact Parker Hannifin for information when
operating at high speeds.
Shaft speed [rpm] 1500 3000 4500 6000 max
F11-5, -6, -10,
-12, -14, -19
[bar] 0.5 - 10 0.5 - 7.0 1.0 - 5.0 2.0 - 5.0 3.0 - 5.0
F12-30, -40,
-60, -80, -90
[bar] 0.5 - 8 0.5 - 6.0 1.0 - 4.5 2.0 - 4.0 -
F12-110, -125,
-152, -162,
-182, -250
[bar] 0.5 - 6 1.0 - 4.0 2.0 - 4.0 - -
Required inlet pressure
The motor may operate as a pump under certain
conditions.
When this occurs, a minimum pressure must be main-
tained at the inlet port; increased noise and gradually
deteriorating performance due to cavitation may
otherwise be experienced.
A 15 bar inlet pressure, measured at the motor inlet
port, satisfies most operating conditions.
Contact Parker Hannifin for more specific information
on inlet pressure requirements.
71
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic motor/pump
Series F11/F12
Catalogue MSG30-8249/UK
5
Spring loaded
check valve
1-3 bar
Drain flow
F12_ports.eps
Leif A./020204
Port C
Port E
(F12-110 and -125)
Port D
Drain flow
Flushing flow
(when required)
Recommended
1-3 bar
Case drain connections
Series F11/F12 have two drain ports, C and D, while
F12-110 and -125 have an additional port, E.
The uppermost drain port (such as port C in the illustra-
tion below) should always be utilized.
Inmountingpositionssuchas'shaftup'(below)
a spring loaded check valve should be installed in the
drain line in order to insure a sufficiently high oil level in
the case.
Preferably, the drain line should be connected directly
to the reservoir.
Before start-up
Make sure the F11/F12 case as well as the entire
hydraulic system is filled with a recommended fluid.
The internal leakage, especially at low operating pres-
sures, is not sufficient to provide lubrication at start-up.
NOTE:
- To avoid cavitation and obtain a low noise level
as well as reduced heat generation, tubes, hoses
and fittings must be adequately dimensioned.
- Preferably, the suction line flow speed should be
0.5 to 1 m/s, and pressure line flow speeds
3 to 5 m/s.
Installation information
Drain flow
Recommended
1-3 bar
Drain flow
Recommended
1-3 bar
Drain flow
Recommended
1-3 bar
Catalogue MSG30-8249/UK. 1.5 M 04/2018, TMCZ© 2018 Parker Hannin Corporation. All rights reserved.
Your local authorized Parker distributor
Ed. 2018-02-08
Europe, Middle East, Africa
AE – United Arab Emirates,
Dubai
Tel: +971 4 8127100
parker.me@parker.com
AT – Austria, Wiener Neustadt
Tel: +43 (0)2622 23501-0
parker.austria@parker.com
AT – Eastern Europe, Wiener
Neustadt
Tel: +43 (0)2622 23501 900
parker.easteurope@parker.com
AZ – Azerbaijan, Baku
Tel: +994 50 2233 458
parker.azerbaijan@parker.com
BE/LU – Belgium, Nivelles
Tel: +32 (0)67 280 900
parker.belgium@parker.com
BG – Bulgaria, Soa
Tel: +359 2 980 1344
parker.bulgaria@parker.com
BY – Belarus, Minsk
Tel: +48 (0)22 573 24 00
parker.poland@parker.com
CH – Switzerland, Etoy
Tel: +41 (0)21 821 87 00
parker.switzerland@parker.com
CZ – Czech Republic, Klecany
Tel: +420 284 083 111
parker.czechrepublic@parker.com
DE – Germany, Kaarst
Tel: +49 (0)2131 4016 0
parker.germany@parker.com
DK – Denmark, Ballerup
Tel: +45 43 56 04 00
parker.denmark@parker.com
ES – Spain, Madrid
Tel: +34 902 330 001
parker.spain@parker.com
FI – Finland, Vantaa
Tel: +358 (0)20 753 2500
parker.nland@parker.com
FR – France, Contamine s/Arve
Tel: +33 (0)4 50 25 80 25
parker.france@parker.com
GR – Greece, Piraeus
Tel: +30 210 933 6450
parker.greece@parker.com
HU – Hungary, Budaörs
Tel: +36 23 885 470
parker.hungary@parker.com
IE – Ireland, Dublin
Tel: +353 (0)1 466 6370
parker.ireland@parker.com
IL – Israel
Tel: +39 02 45 19 21
parker.israel@parker.com
IT – Italy, Corsico (MI)
Tel: +39 02 45 19 21
parker.italy@parker.com
KZ – Kazakhstan, Almaty
Tel: +7 7273 561 000
parker.easteurope@parker.com
NL – The Netherlands, Oldenzaal
Tel: +31 (0)541 585 000
parker.nl@parker.com
NO – Norway, Asker
Tel: +47 66 75 34 00
parker.norway@parker.com
PL – Poland, Warsaw
Tel: +48 (0)22 573 24 00
parker.poland@parker.com
PT – Portugal
Tel: +351 22 999 7360
parker.portugal@parker.com
RO – Romania, Bucharest
Tel: +40 21 252 1382
parker.romania@parker.com
RU – Russia, Moscow
Tel: +7 495 645-2156
parker.russia@parker.com
SE – Sweden, Spånga
Tel: +46 (0)8 59 79 50 00
parker.sweden@parker.com
SK – Slovakia, Banská Bystrica
Tel: +421 484 162 252
parker.slovakia@parker.com
SL – Slovenia, Novo Mesto
Tel: +386 7 337 6650
parker.slovenia@parker.com
TR – Turkey, Istanbul
Tel: +90 216 4997081
parker.turkey@parker.com
UA – Ukraine, Kiev
Tel: +48 (0)22 573 24 00
parker.poland@parker.com
Parker Worldwide
UK – United Kingdom, Warwick
Tel: +44 (0)1926 317 878
parker.uk@parker.com
ZA – South Africa, Kempton Park
Tel: +27 (0)11 961 0700
parker.southafrica@parker.com
North America
CA – Canada, Milton, Ontario
Tel: +1 905 693 3000
US – USA, Cleveland
Tel: +1 216 896 3000
Asia Pacific
AU – Australia, Castle Hill
Tel: +61 (0)2-9634 7777
CN – China, Shanghai
Tel: +86 21 2899 5000
HK – Hong Kong
Tel: +852 2428 8008
IN – India, Mumbai
Tel: +91 22 6513 7081-85
JP – Japan, Tokyo
Tel: +81 (0)3 6408 3901
KR – South Korea, Seoul
Tel: +82 2 559 0400
MY – Malaysia, Shah Alam
Tel: +60 3 7849 0800
NZ – New Zealand, Mt Wellington
Tel: +64 9 574 1744
SG – Singapore
Tel: +65 6887 6300
TH – Thailand, Bangkok
Tel: +662 186 7000
TW – Taiwan, Taipei
Tel: +886 2 2298 8987
South America
AR – Argentina, Buenos Aires
Tel: +54 3327 44 4129
BR – Brazil, Sao Jose dos Campos
Tel: +55 800 727 5374
CL – Chile, Santiago
Tel: +56 2 623 1216
MX – Mexico, Toluca
Tel: +52 72 2275 4200
EMEA Product Information Centre
Free phone: 00 800 27 27 5374
(from AT, BE, CH, CZ, DE, DK, EE, ES, FI, FR, IE, IL,
IS, IT, LU, MT, NL, NO, PL, PT, RU, SE, SK, UK, ZA)
US Product Information Centre
Toll-free number: 1-800-27 27 537
www.parker.com