Axial Piston Pump

PV016 - PV360

Variable Displacement

3

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Contents

Contents Page

Introduction and general Information ..............................................................4

Technical Data ................................................................................................5

Ordering Code ................................................................................................ 6

Pressure Controls .........................................................................................18

Remote Pressure Controls ...........................................................................20

Load Sensing Controls .................................................................................22

Horse Power/Torque Controls .......................................................................26

Performance Curves .....................................................................................30

Electronic P/Q Controls ................................................................................32

Proportional Displacement Control ...............................................................32

Electronic P/Q Controls ................................................................................33

Efﬁciency and Case Drain Flows ..................................................................34

Performance Curves and Case Drain Flows PV 360 ....................................39

Accessories Control......................................................................................40

Proportional pressure relief valve PVACRE* ................................................ 42

Accessories Control......................................................................................43

Dimensions ...................................................................................................44

Control Dimensions ......................................................................................56

Electronic Module PQDXXA .........................................................................60

Through Drive, Mounting Kits ....................................................................... 61

Through Drive, Flange Load Limitation ........................................................62

Multiple Pump Combinations - Maximum Moment .......................................62

Through Drive, Shaft Load Limitations .........................................................63

PV360 shaft options .....................................................................................64

4

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

With thru drive for single and multiple pumps

Swash plate type for open circuit

Introduction

Technical Features

• Lownoiselevel

• Fastresponse

• Service-friendly

• Highself-primingspeed

• Compactdesign

• Thrudrivefor100%nominaltorque

General Information

Fluid recommendations

Premium quality hydraulic mineral ﬂuid is recomended,

like HLP oils to DIN 51524, part 2. Brugger- value

has to be 30 N/mm

2

minimum for general application

and 50 N/mm

2

for heavily loaded hydraulic equipment

and fast cycling machines and/or high dynamic loads,

measured in accordance with DIN 51 347-2. See also

Document HY30-3248/UK Parker Hydraulic Fluids.

Viscosity

The normal operating viscosity should range between

16 and 100 mm

2

/s (cSt). Max. start-up viscosity is

800 mm

2

/s (cSt).

Filtration

For maximum pump and system component func-

tionality and life, the system should be protected from

contamination by effective ﬁltration.

Fluid cleanliness should be in accordance with ISO

classiﬁcation ISO 4406:1999. The quality of ﬁlter

elements should be in accordance with ISO standards.

General hydraulic systems for satisfactory operation:

Class 20/18/15, according to ISO 4406:1999

Recommended cleanliness for maximum component

life and functionality: Class 18/16/13, according to ISO

4406:1999

Seals

Check hydraulic ﬂuid speciﬁcation for chemical resistance

of seal material.

Check temperature range of seal material and compare

with max. system and ambient temperature.

N - Nitrile -40 ... +90 °C

Note: The highest ﬂuid temperature will be at the drain

port of the pump, up to 25 °C higher than in the

reservoir.

5

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Technical Data

PV016 PV020 PV023 PV028 PV032 PV040 PV046

Frame size 1 1 1 1 2 2 2

Max. Displacement [cm

3

/rev.] 16 20 23 28 32 40 46

Output ﬂow at 1500 rpm [l/min] 24 30 34,5 42 48 60 69

Nominal pressure pN [bar] 350 350 350 350 350 350 350

Max.pressurepmaxat20%workingcycle

1)

[bar] 420 420 420 420 420 420 420

Case drain pressure, continuous [bar] 0.5 0.5 0.5 0.5 0.5 0.5 0.55

Case drain pressure, max. peak [bar] 2.0 2.0 2.0 2.0 2.0 2.0 2.0

Min. Inlet pressure, abs. [bar] 0.8 0.8 0.8 0.8 0.8 0.8 0.8

Max. Inlet pressure [bar] 16 16 16 16 16 16 16

Input power at 1500 rpm and 350 bar [kW] 15.5 19.5 22.5 27.5 31 39 45

Max speed at 1 bar, abs, inlet pressure [rpm] 3000 3000 3000 3000 2800 2800 2800

Moment of inertia [kgm

2

] 0.0017 0.0017 0.0017 0.0017 0.0043 0.0043 0.0043

Weight [kg] 19 19 19 19 30 30 30

PV063 PV080 PV092 PV140 PV180 PV270 PV360

Frame size 3 3 3 4 4 5 5

Max. Displacement [cm

3

/rev.] 63 80 92 140 180 270 360

Output ﬂow at 1500 rpm [l/min] 94.5 120 138 270 405 405 540

Nominal pressure pN [bar] 350 350 350 350 350 350 350

Max.pressurepmaxat20%workingcycle

1)

[bar] 420 420 420 420 420 420 420

Case drain pressure, continuous [bar] 0.5 0.5 0.5 0.5 0.5 0.5 0.5

Case drain pressure, max. peak [bar] 2.0 2.0 2.0 2.0 2.0 2.0 2.0

Min. Inlet pressure, abs. [bar] 0.8 0.8 0.8 0.8 0.8 0.8 0.8

Max. Inlet pressure [bar] 16 16 16 16 16 16 16

Input power at 1500 rpm and 350 bar [kW] 61.5 78 89.5 136 175 263 350

Max speed at 1 bar, abs, inlet pressure [rpm] 2800 2500 2300 2400 2200 1800 1750

Moment of inertia [kgm

2

] 0.018 0.018 0.018 0.030 0.030 0.098 0.103

Weight [kg] 59 59 59 90 90 172 180

1) Special control options required.

6

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 028

Ordering Code

Code Variation

1 Standard

9 Special

adjustment

2)

Code Port

3)

Threads

4)

1 BSPP metric

3 UNF UNC

7 ISO 6149 UNC

8

5)

ISO 6149 metric

3)

Drain, gauge and ﬂushing ports

4)

All mounting and connecting threads

5)

Mounting interface, code K and L only

Code Mounting interface Shaft

K metr. ISO 4-hole ﬂange Ø100 mm Cylindric, key

L 3019/2 4-hole ﬂange Ø100 mm Splined, DIN 5480

D SAE 4-hole ﬂange SAE B Cylindric, key

E ISO 4-hole ﬂange SAE B-B Splined, SAE

3019/1

Code Displacement Size

016 16 cm³/rev 1

020 20 cm³/rev 1

023 23 cm³/rev 1

028 28 cm³/rev 1

See dimensions for details

6)

to be ordered separately as single part

x= Frame size, see displacement.

axial piston

pump

variable

displacement

P V

mounting

interface

1 K TR 1 1 N

control

see next page

variation

threads

code

coupling

code

thru drive

code

size

and

displacement

rotation

seals

Code Thru drive option

No adaptor for 2nd pump

T

Single pump prepared

for thru drive

with adaptor for 2nd pump as single part

6)

Y SAE AA, Ø 50.8 mm MK-PVBGxYMN

A SAE A, Ø 82.55 mm MK-PVBGxAMN

B SAE B, Ø 101.6 mm MK-PVBGxBMN

G metric, Ø 63 mm MK-PVBGxGMN

H metric, Ø 80 mm MK-PVBGxHMN

J metric, Ø 100 mm MK-PVBGxJMN

Code Coupling for thru drive as single part

6)

1 Single pump, no coupling

H with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBGxK01

Y with coupling SAE A 9T-16/32 DP MK-PVBGxK11

A with coupling SAE - 11T-16/32 DP MK-PVBGxK12

B with coupling SAE B 13T-16/32 DP MK-PVBGxK13

C with coupling SAE B-B 15T-16/32 DP MK-PVBGxK14

2)

requires Kxxxx number

Code Rotation

1)

R Clockwise

L Counter clockwise

1)

When looked on shaft

Code Seals

N NBR

V FPM

W NBR with PTFE shaft seal

P FPM with PTFE shaft seal

7

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 028

Code Control option

electro hydraulic control

F P V Proportional displacement control, no pressure

compensation

U P Proportional displacement control, with pressure

compensation

Control variation

R pilot operated pressure control, open

NG6 interface

K pilot operated pressure control, proportional

pilot valve type PVACRE..35 mounted

M pilot operated pressure control, pressure sensor

and proportional pilot valve type PVACRE..35

mounted for pressure control and/or power

control

Ordering Code

Horse power / Torque control

Displacem. Code

016 Nominal HP Nominal

028 at 1.500 rpm torque

B 3 kW 20 Nm

C 4 kW 25 Nm

D 5.5 kW 35 Nm

E 7.5 kW 50 Nm

G 11 kW 71 Nm

H 15 kW 97 Nm

K 18.5 kW 120 Nm

Function

L Horse power control with pressure control

C Horse power control with load sensing (single spool)

Control variation

C Standard version

1 NG 6 interface top side

W With unloading function, 24 VDC solenoid

K Prop.-pilot valve type PVACRE..35 mounted

Z Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

Code Control options

0 0 1 No control

1 0 0 With cover plate, no control function

M M Standard pressure control, integrated pilot valve

M R Remote pressure control, integrated pilot valve

M F Load Sensing (ﬂow) control, integrated pilot valve

M T Two spool LS control

Control variation

C Standard version

1)

1 NG6 interface top side for pilot valves

W With unloading function, 24VDC solenoid

1)

K Prop.-pilot valve type PVACRE..35 mounted

Z

Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

P MT1 with mounted pilot valve PVAC1P

2)

1) not for MT

2) only for MT

8

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 032 to 046

Ordering Code

Code Variation

1 Standard

9 Special

adjustment

2)

requires Kxxxx number

Code Mounting interface Shaft

K metr. ISO 4-hole ﬂange Ø125 mm Cylindric, key

L 3019/2 4-hole ﬂange Ø125 mm Splined, DIN 5480

D SAE 4-hole ﬂange SAE C Cylindric, key

E ISO 4-hole ﬂange SAE C Splined, SAE

3019/1

Code Displacement Size

032 32 cm³/rev 2

040 40 cm³/rev 2

046 46 cm³/rev 2

Code Thru drive option

No adaptor for 2nd pump

T

Single pump prepared

for thru drive

with adaptor for 2nd pump as single part

6)

A SAE A, Ø 82.55 mm MK-PVBGxAMN

B SAE B, Ø 101.6 mm MK-PVBGxBMN

C SAE C, Ø 127 mm MK-PVBGxCMN

G metric, Ø 63 mm MK-PVBGxGMN

H metric, Ø 80 mm MK-PVBGxHMN

J metric, Ø 100 mm MK-PVBGxJMN

K metric, Ø 125 mm MK-PVBGxKMN

Code Coupling for thru drive as single part

6)

1 Single pump, no coupling

H with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBGxK01

J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBGxK02

Y with coupling SAE A 9T-16/32 DP MK-PVBGxK11

A with coupling SAE - 11T-16/32 DP MK-PVBGxK12

B with coupling SAE B 13T-16/32 DP MK-PVBGxK13

C with coupling SAE B-B 15T-16/32 DP MK-PVBGxK14

D with coupling SAE C 14T-12/24 DP MK-PVBGxK15

See dimensions for details

6)

to be ordered separately as single part

x= Frame size, see displacement.

axial piston

pump

variable

displacement

P V

mounting

interface

1 K TR 1 1 N

control

see next page

variation

threads

code

coupling

code

thru drive

code

size

and

displacement

rotation

seals

Code Port

3)

Threads

4)

1 BSPP metric

3 UNF UNC

7 ISO 6149 UNC

8

5)

ISO 6149 metric

3)

Drain, gauge and ﬂushing ports

4)

All mounting and connecting threads

5)

Mounting interface, code K and L only

Code Rotation

1)

R Clockwise

L Counter clockwise

1)

When looked on shaft

Code Seals

N NBR

V FPM

W NBR with PTFE shaft seal

P FPM with PTFE shaft seal

9

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 032 to 046

Code Control options

0 0 1 No control

1 0 0 With cover plate, no control function

M M Standard pressure control, integrated pilot valve

M R Remote pressure control, integrated pilot valve

M F Load Sensing (ﬂow) control, integrated pilot valve

M T Two spool LS control

Control variation

C Standard version

1)

1 NG6 interface top side for pilot valves

W With unloading function, 24VDC solenoid

1)

K Prop.-pilot valve type PVACRE..35 mounted

Z

Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

P MT1 with mounted pilot valve PVAC1P

2)

Code Control option

electro hydraulic control

F P V Proportional displacement control, no pressure

compensation

U P Proportional displacement control, with pressure

compensation

Control variation

R pilot operated pressure control, open

NG6 interface

K pilot operated pressure control, proportional

pilot valve type PVACRE..35 mounted

M pilot operated pressure control, pressure sensor

and proportional pilot valve type PVACRE..35

mounted for pressure control and/or power

control

Ordering Code

1) not for MT

2) only for MT

Horse power / Torque control

Displacem. Code

032 Nominal HP Nominal

046 at 1.500 rpm torque

D 5.5 kW 35 Nm

E 7.5 kW 50 Nm

G 11 kW 71 Nm

H 15 kW 97 Nm

K 18.5 kW 120 Nm

M 22 kW 142 Nm

S 30 kW 195 Nm

Function

L Horse power control with pressure control

C Horse power control with load sensing (single spool)

Control variation

C Standard version

1 NG 6 interface top side

W With unloading function, 24 VDC solenoid

K Prop.-pilot valve type PVACRE..35 mounted

Z Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

10

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 063 to 092

Code Seals

N NBR

V FPM

W NBR with PTFE shaft seal

P FPM with PTFE shaft seal

Code Variation

1 Standard

9 special

adjustment

2)

Code Rotation

1)

R Clockwise

L Counter clockwise

1)

When looked on shaft

2)

requires Kxxxx number

Code Port

3)

Threads

4)

1 BSPP metric

3 UNF UNC

4

5)

BSPP metr. M14

7 ISO 6149 UNC

8 ISO 6149 metric

3)

Drain, gauge and ﬂushing ports

4)

All mounting and connecting threads

5)

For PV063-PV092 only: pressure port 1 1/4"

with 4 x M14 instead of 4 x M12

Code Displacement Size

063 63 cm³/rev 3

080 80 cm³/rev 3

092 92 cm³/rev 3

Code Thru drive option

No adaptor for 2nd pump

T

Single pump prepared

for thru drive

with adaptor for 2nd pump as single part

6)

A SAE A, Ø 82.55 mm MK-PVBGxAMN

B SAE B, Ø 101.6 mm MK-PVBGxBMN

C SAE C, Ø 127 mm MK-PVBGxCMN

D SAE D, Ø 152,4 mm MK-PVBGxDMN

G metric, Ø 63 mm MK-PVBGxGMN

H metric, Ø 80 mm MK-PVBGxHMN

J metric, Ø 100 mm MK-PVBGxJMN

K metric, Ø 125 mm MK-PVBGxKMN

L metric, Ø 160 mm MK-PVBGxLMN

axial piston

pump

variable

displacement

high

pressure

version

P V

mounting

interface

1 K TR 1 1 N

compensator

see next page

variation

threads

code

coupling

code

thru drive

code

size

and

displacement

rotation

seals

Ordering Code

Code Coupling for thru drive as single part

6)

1 Single pump, no coupling

H with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBGxK01

J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBGxK02

K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBGxK03

Y with coupling SAE A 9T-16/32 DP MK-PVBGxK11

A with coupling SAE - 11T-16/32 DP MK-PVBGxK12

B with coupling SAE B 13T-16/32 DP MK-PVBGxK13

C with coupling SAE B-B 15T-16/32 DP MK-PVBGxK14

D with coupling SAE C 14T-12/24 DP MK-PVBGxK15

E with coupling SAE C - C MK-PVBGxK16

F with coupling SAE D, E MK-PVBGxK17

See dimensions for details

6)

to be ordered separately as single part

x= Frame size, see displacement.

Code Mounting interface Shaft

K metr. ISO 4-hole ﬂange Ø160 mm Cylindric, key

L 3019/2 4-hole ﬂange Ø160 mm Splined, DIN 5480

D SAE 4-hole ﬂange SAE D Cylindric, key

E ISO 4-hole ﬂange SAE D Splined, SAE

3019/1

11

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 063 to 092

Ordering Code

Code Control options

0 0 1 No control

1 0 0 With cover plate, no control function

M M Standard pressure control, integrated pilot valve

M R Remote pressure control, integrated pilot valve

M F Load Sensing (ﬂow) control, integrated pilot valve

M T Two spool LS control

Control variation

C Standard version

1)

1 NG6 interface top side for pilot valves

W With unloading function, 24VDC solenoid

1)

K Prop.-pilot valve type PVACRE..35 mounted

Z

Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

P MT1 with mounted pilot valve PVAC1P

2)

1) not for MT

2) only for MT

Code Control option

electro hydraulic control

F P V Proportional displacement control, no pressure

compensation

U P Proportional displacement control, with pressure

compensation

Control variation

R pilot operated pressure control, open

NG6 interface

K pilot operated pressure control, proportional

pilot valve type PVACRE..35 mounted

M pilot operated pressure control, pressure sensor

and proportional pilot valve type PVACRE..35

mounted for pressure control and/or power

control

Horse power / Torque control

Displacem. Code

063 Nominal HP Nominal

092 at 1.500 rpm torque

G 11 kW 71 Nm

H 15 kW 97 Nm

K 18.5 kW 120 Nm

M 22kW 142 Nm

S 30 kW 195 Nm

T 37 kW 240 Nm

U 45 kW 290 Nm

W 55 kW 355 Nm

Function

L Horse power control with pressure control

C Horse power control with load sensing (single spool)

Control variation

C Standard version

1 NG 6 interface top side

W With unloading function, 24 VDC solenoid

K Prop.-pilot valve type PVACRE..35 mounted

Z Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

12

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 140 to 180

Ordering Code

Code Variation

1 Standard

9 Special

adjustment

2)

requires Kxxxx number

Code Port

3)

Threads

4)

1 BSPP metric

3 UNF UNC

4

5)

BSPP metr. M14

7 ISO 6149 UNC

8

6)

ISO 6149 metric

3)

Drain, gauge and ﬂushing ports

4)

All mounting and connecting threads

5)

Pressure port 1 1/4" with 4 x M14 instead of 4 x M12

6)

Mounting interface, code K and L only

Code Mounting interface Shaft

K metr. ISO 4-hole ﬂange Ø160 mm Cylindric, key

L 3019/2 4-hole ﬂange Ø160 mm Splined, DIN 5480

D SAE 4-hole ﬂange SAE D Cylindric, key

E ISO 4-hole ﬂange SAE D-F Splined, SAE

3019/1

F 4-hole ﬂange SAE D Cylindric, key

G 4-hole ﬂange SAE D Splined, SAE

Code Displacement Size

140 140 cm³/rev 4

180 180 cm³/rev 4

Code Thru drive option

No adaptor for 2nd pump

T

Single pump prepared

for thru drive

with adaptor for 2nd pump as single part

7)

A SAE A, Ø 82.55 mm MK-PVBGxAMN

B SAE B, Ø 101.6 mm MK-PVBGxBMN

C SAE C, Ø 127 mm MK-PVBGxCMN

D SAE D, Ø 152.4 mm MK-PVBGxDMN

H metric, Ø 80 mm MK-PVBGxHMN

J metric, Ø 100 mm MK-PVBGxJMN

K metric, Ø 125 mm MK-PVBGxKMN

L metric, Ø 160 mm MK-PVBGxLMN

Code Coupling for thru drive as single part

7)

1 Single pump, no coupling

H with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBGxK01

J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBGxK02

K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBGxK03

L with coupling 50 x 2 x 24, DIN 5480 MK-PVBGxK04

Y with coupling SAE A 9T-16/32 DP MK-PVBGxK11

A with coupling SAE - 11T-16/32 DP MK-PVBGxK12

B with coupling SAE B 13T-16/32 DP MK-PVBGxK13

C with coupling SAE B-B 15T-16/32 DP MK-PVBGxK14

D with coupling SAE C 14T-12/24 DP MK-PVBGxK15

E with coupling SAE C - C MK-PVBGxK16

F with coupling SAE D, E MK-PVBGxK17

G with coupling SAE F MK-PVBGxK18

See dimensions for details

7)

to be ordered separately as single part

x= Frame size, see displacement.

axial piston

pump

variable

displacement

P V

mounting

interface

1 K TR 1 1 N

control

see next page

variation

threads

code

coupling

code

thru drive

code

size

and

displacement

rotation

seals

Code Rotation

1)

R Clockwise

L Counter clockwise

1)

When looked on shaft

Code Seals

N NBR

V FPM

W NBR with PTFE shaft seal

P FPM with PTFE shaft seal

13

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 140 to 180

Code Control options

0 0 1 No control

1 0 0 With cover plate, no control function

M M Standard pressure control, integrated pilot valve

M R Remote pressure control, integrated pilot valve

M F Load Sensing (ﬂow) control, integrated pilot valve

M T Two spool LS control

Control variation

C Standard version

1)

1 NG6 interface top side for pilot valves

W With unloading function, 24VDC solenoid

1)

K Prop.-pilot valve type PVACRE..35 mounted

Z

Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

P MT1 with mounted pilot valve PVAC1P

2)

Code Control option

electro hydraulic control

F P V Proportional displacement control, no pressure

compensation

U P Proportional displacement control, with pressure

compensation

Control variation

R pilot operated pressure control, open

NG6 interface

K pilot operated pressure control, proportional

pilot valve type PVACRE..35 mounted

M pilot operated pressure control, pressure sensor

and proportional pilot valve type PVACRE..35

mounted for pressure control and/or power

control

Ordering Code

1) not for MT

2) only for MT

Horse power / Torque control

Displacem. Code

140 180 Nominal HP Nominal

at 1.500 rpm torque

K 18.5 kW 120 Nm

M 22 kW 142 Nm

S 30 kW 195 Nm

T 37 kW 240 Nm

U 45 kW 290 Nm

W 55 kW 355 Nm

Y 75 kW 485 Nm

Z 90 kW 585 Nm

2 110 kW 715 Nm

Function

L Horse power control with pressure control

C Horse power control with load sensing (single spool)

Control variation

C Standard version

1 NG 6 interface top side

W With unloading function, 24 VDC solenoid

K Prop.-pilot valve type PVACRE..35 mounted

Z Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

14

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 270

Code Seals

N NBR

V FPM

W NBR with PTFE shaft seal

P FPM with PTFE shaft seal

Code Variation

1 Standard

9 special

adjustment

2)

Code Rotation

1)

R Clockwise

L Counter clockwise

1)

When looked on shaft

2)

requires Kxxxx number

Code Port

4)

Threads

5)

1 BSPP metric

3 UNF UNC

7 ISO 6149 UNC

8 ISO 6149 metric

4)

Drain, gauge and ﬂushing ports

5)

All mounting and connecting threads

Code Displacement Size

270 270 cm³/rev 5

Code Thru drive option

No adaptor for 2nd pump

T

Single pump prepared

for thru drive

with adaptor for 2nd pump as single part

6)

A SAE A, Ø 82.55 mm MK-PVBGxAMN

B SAE B, Ø 101.6 mm MK-PVBGxBMN

C SAE C, Ø 127 mm MK-PVBGxCMN

D SAE D, Ø 152,4 mm MK-PVBGxDMN

E SAE E, Ø 165,1 mm MK-PVBGxEMN

H metric, Ø 80 mm MK-PVBGxHMN

J metric, Ø 100 mm MK-PVBGxJMN

K metric, Ø 125 mm MK-PVBGxKMN

L metric, Ø 160 mm MK-PVBGxLMN

M metric, Ø 200 mm MK-PVBGxMMN

axial piston

pump

variable

displacement

high

pressure

version

P V

mounting

interface

1 K TR 1 1 N

compensator

see next page

variation

threads

code

coupling

code

thru drive

code

size

and

displacement

rotation

seals

Ordering Code

Code Coupling for thru drive as single part

6)

1 Single pump, no coupling

H with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBGxK01

J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBGxK02

K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBGxK03

L with coupling 50 x 2 x 24, DIN 5480 MK-PVBGxK04

M with coupling 60 x 2 x 28, DIN 5480 MK-PVBGxK05

Y with coupling SAE A 9T-16/32 DP MK-PVBGxK11

A with coupling SAE - 11T-16/32 DP MK-PVBGxK12

B with coupling SAE B 13T-16/32 DP MK-PVBGxK13

C with coupling SAE B-B 15T-16/32 DP MK-PVBGxK14

D with coupling SAE C 14T-12/24 DP MK-PVBGxK15

E with coupling SAE C - C MK-PVBGxK16

F with coupling SAE D, E MK-PVBGxK17

See dimensions for details

6)

to be ordered separately as single part

x= Frame size, see displacement.

Code Mounting interface Shaft

K metr. ISO 4-hole ﬂange Ø200 mm Cylindric, key

L 3019/2 4-hole ﬂange Ø200 mm Splined, DIN 5480

D SAE 4-hole ﬂange SAE E Cylindric, key

E ISO 4-hole ﬂange SAE E-F Splined, SAE

3019/1

15

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 270

Ordering Code

Code Control options

0 0 1 No control

1 0 0 With cover plate, no control function

M M Standard pressure control, integrated pilot valve

M R Remote pressure control, integrated pilot valve

M F Load Sensing (ﬂow) control, integrated pilot valve

M T Two spool LS control

Control variation

C Standard version

1)

1 NG6 interface top side for pilot valves

W With unloading function, 24VDC solenoid

1)

K Prop.-pilot valve type PVACRE..35 mounted

Z

Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

P MT1 with mounted pilot valve PVAC1P

2)

Code Control option

electro hydraulic control

F P V Proportional displacement control, no pressure

compensation

U P Proportional displacement control, with pressure

compensation

Control variation

R pilot operated pressure control, open

NG6 interface

K pilot operated pressure control, proportional

pilot valve type PVACRE..35 mounted

M pilot operated pressure control, pressure sensor

and proportional pilot valve type PVACRE..35

mounted for pressure control and/or power

control

1) not for MT

2) only for MT

Horse power / Torque control

Displacem. Code

270 Nominal HP Nominal

at 1.500 rpm torque

T 37 kW 240 Nm

U 45 kW 290 Nm

W 55 kW 350 Nm

Y 75 kW 480 Nm

Z 90 kW 580 Nm

2 110 kW 700 Nm

3 132 kW 840 Nm

Function

L Horse power control with pressure control

C Horse power control with load sensing (single spool)

Control variation

C Standard version

1 NG 6 interface top side

W With unloading function, 24 VDC solenoid

K Prop.-pilot valve type PVACRE..35 mounted

Z Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

16

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 360

Ordering Code

Code Seals

N NBR

V FPM

Code Variation

1 Standard

9 Special

adjustment

2)

Code Rotation

1)

R Clockwise

1)

When looked on shaft

2)

requires Kxxxx number

Code Port

3)

Threads

4)

1 BSPP metric

3 UNF UNC

3)

Drain, gauge and ﬂushing ports

4)

All mounting and connecting threads

Code Mounting interface Shaft

K 4-hole ﬂange Ø250 mm Cylindric, key

L metr. ISO 4-hole ﬂange Ø250 mm Splined, DIN 5480

R 3019/2 4-hole ﬂange Ø224 mm Cylindric, key

T 4-hole ﬂange Ø224 mm Splined, DIN 5480

D SAE 4-hole ﬂange SAE E Cylindric, key

E ISO 4-hole ﬂange SAE E Splined, SAE

3019/1

Code Displacement Size

360 360 cm³/rev 5

Code Thru drive option

No adaptor for 2nd pump

T

Single pump prepared

for thru drive

with adaptor for 2nd pump as single part

6)

A SAE A, Ø 82.55 mm MK-PVBGxAMN

B SAE B, Ø 101.6 mm MK-PVBGxBMN

C SAE C, Ø 127 mm MK-PVBGxCMN

D SAE D, Ø 152.4 mm MK-PVBGxDMN

E SAE E, Ø 165.1 mm MK-PVBGxEMN

H metric, Ø 80 mm MK-PVBGxHMN

J metric, Ø 100 mm MK-PVBGxJMN

K metric, Ø 125 mm MK-PVBGxKMN

L metric, Ø 160 mm MK-PVBGxLMN

M metric, Ø 200 mm MK-PVBGxMMN

Code Coupling for thru drive as single part

6)

1 Single pump, no coupling

H with coupling 25 x 1.5 x 15, DIN 5480 MK-PVBGxK01

J with coupling 32 x 1.5 x 20, DIN 5480 MK-PVBGxK02

K with coupling 40 x 1.5 x 25, DIN 5480 MK-PVBGxK03

L with coupling 50 x 2 x 24, DIN 5480 MK-PVBGxK04

M with coupling 60 x 2 x 28, DIN 5480 MK-PVBGxK05

P with coupling 70 x 3 x 22, DIN 5480 MK-PVBGxK06

Y with coupling SAE A 9T-16/32 DP MK-PVBGxK11

A with coupling SAE - 11T-16/32 DP MK-PVBGxK12

B with coupling SAE B 13T-16/32 DP MK-PVBGxK13

C with coupling SAE B-B 15T-16/32 DP MK-PVBGxK14

D with coupling SAE C 14T-12/24 DP MK-PVBGxK15

E with coupling SAE C - C MK-PVBGxK16

F with coupling SAE D, E MK-PVBGxK17

G with coupling SAE F MK-PVBGxK18

See dimensions for details

6)

to be ordered separately as single part

x= Frame size, see displacement.

axial piston

pump

variable

displacement

P V

mounting

interface

1 K TR 1 1 N

control

see next page

variation

threads

code

coupling

code

thru drive

code

size

and

displacement

rotation

seals

17

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 360

Code Control options

0 0 1 No control

1 0 0 With cover plate, no control function

M M Standard pressure control, integrated pilot valve

M R Remote pressure control, integrated pilot valve

M F Load Sensing (ﬂow) control, integrated pilot valve

M T Two spool LS control

Control variation

C Standard version

1)

1 NG6 interface top side for pilot valves

W With unloading function, 24VDC solenoid

1)

K Prop.-pilot valve type PVACRE..35 mounted

Z

Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

P MT1 with mounted pilot valve PVAC1P

2)

Code Control option

electro hydraulic control

F P V Proportional displacement control, no pressure

compensation

U P Proportional displacement control, with pressure

compensation

Control variation

R pilot operated pressure control, open

NG6 interface

K pilot operated pressure control, proportional

pilot valve type PVACRE..35 mounted

M pilot operated pressure control, pressure sensor

and proportional pilot valve type PVACRE..35

mounted for pressure control and/or power

control

Ordering Code

1) not for MT

2) only for MT

Horse power / Torque control

Displacem. Code

360 Nominal HP Nominal

at 1.500 rpm torque

U 45 kW 290 Nm

W 55 kW 350 Nm

Y 75 kW 480 Nm

Z 90 kW 580 Nm

2 110 kW 700 Nm

3 132 kW 840 Nm

4 160 kW 1020 Nm

5 180 kW 1150 Nm

6 200 kW 1280 Nm

Function

L Horse power control with pressure control

C Horse power control with load sensing (single spool)

Control variation

C Standard version

1 NG 6 interface top side

W With unloading function, 24 VDC solenoid

K Prop.-pilot valve type PVACRE..35 mounted

Z Without integrated pilot valve, NG6 interface,

for mounting of accessory code PVAC*

18

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Standard Pressure Control

Control option MMC

The standard pressure control adjusts the pump displacement according to

the actual need of ﬂow in the system in order to keep the pressure constant.

Control schematics

Response times of the pump are collected from a

circuit as below by measuring the pumps swash angle

movement at different pressures.

Dynamic characteristic of ﬂow control *

t on stroke t

de-stroke

Displacement [%]

0

25

50

75

100

Response time

Pressure Controls

ST

M

P1 P

AP

T

P A

T

Time on-stroke [ms] Time de-stroke [ms]

against

50 bar

against

350 bar

zero stroke

50 bar

zero stroke

350 bar

PV360 520 180 120 82

Pressure adjustment range 15 to 350 bar

Factory setting pressure 50 bar

Differential pressure adjustment range 10 to 40 bar

Factory setting differential pressure 15 bar

Control oil consumption Max 8.0 l/min

* Curve shown exaggerated

On/Off valve

19

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

ST

M

P1 P

AP

T

PA

T

P

Pressure Controls

Control option MM1

With code MM1 the standard pressure control has a

valve interface size NG 6 DIN 24340 (CETOP 03 acc.

RP35H, NFPA D03) on the top side.

This interface allows the mounting of accessories like

multiple pressure selectors without the need of external

piping and valve mounting.

Standard Pressure Control with NG6 Interface

ST

M

P1 P

AP

T

PA

T

P

Standard Pressure Control with Electrical Unloading

Control option MMW

With code MMW a solenoid operated directional control

valve (D1VW002KNJW) for electrical unloading is

mounted on the control top side.

When the solenoid is de-energised, the pump compen-

sates at a stand-by pressure of typically 15 bar. When

the solenoid is energised, the pump compensates at

the pressure adjusted on the integrated pilot valve.

Standard Pressure Control with Proportional Pilot Valve

Control option MMK

With code MMK a proportional pilot valve of type

PVACRE..35 (see page 35) is mounted on the top side

interface.

This allows a variation of the pump compensating pres-

sure between 20 and 350 bar by an electrical signal.

Control option MMZ

Control MMZ has no integrated pilot valve but a valve

interface NG6 DIN 24340 on the top.

This version is recommended for valve accessories.

Standard Pressure Control with Accessory

ST

M

P1 P

AP

T

PA

T

P

ST

M

P1 P

AP

T

PA

T

P

20

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Remote Pressure Control

Control option MRC

The remote pressure control adjusts the pump displacement according to the actual need of ﬂow in the system in

order to keep the pressure constant at a level given by a remotely installed pilot valve.

Control schematics

Response times of the pump are collected from a

circuit as below by measuring the pumps swash angle

movement at different pressures.

Dynamic characteristic of ﬂow control *

Remote Pressure Controls

ST

M

P1 P

AP

T

P A

T

PR

Pressure adjustment range 15 to 350 bar

Factory setting pressure 50 bar

Differential pressure adjustment range 10 to 40 bar

Factory setting differential pressure 15 bar

Control oil consumption Max 8.0 l/min

* Curve shown exaggerated

t on stroke t

de-stroke

Displacement [%]

0

25

50

75

100

Response time

Time on-stroke [ms] Time de-stroke [ms]

against

50 bar

against

350 bar

zero stroke

50 bar

zero stroke

350 bar

PV360 520 180 120 82

On/Off valve

21

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

ST

M

P1 P

AP

T

PA

T

PR

T

P

Remote Pressure Controls

Control option MR1

With code MR1 the remote pressure control has a

valve interface size NG 6 DIN 24340 (CETOP 03 acc.

RP35H, NFPA D03) on the top side.

This interface allows the mounting of accessories like

multiple pressure selectors without the need of external

piping and valve mounting.

Remote Pressure Control with NG6 Interface

ST

M

P1 P

AP

T

PA

T

PR

T

P

Remote Pressure Control with Electrical Unloading

Control option MRW

With code MRW a solenoid operated directional control

valve (D1VW002KNJW) for electrical unloading is

mounted on the control top side.

When the solenoid is de-energised, the pump compen-

sates at a stand-by pressure of typically 15 bar. When

the solenoid is energised, the pump compensates at

the pressure adjusted on the integrated pilot valve.

Remote Pressure Control with Proportional Pilot Valve

Control option MRK

With code MRK a proportional pilot valve of type

PVACRE..35 (see page 35) is mounted on the top side

interface.

This allows a variation of the pump compensating pres-

sure between 20 and 350 bar by an electrical signal.

Control option MRZ

Control MRZ has no integrated pilot valve but a valve

interface NG6 DIN 24340 on the top.

This version is recommended for valve accessories.

Remote Pressure Control with Accessory

ST

M

P1

P

AP

T

PA

T

PR

T

P

ST

M

P1

P

AP

T

PA

T

PR

T

P

22

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Load Sensing Control

Control option MFC

The pilot pressure of the load sensing control is taken from a load sensing port in the hydraulic system.

It is used to match pump ﬂow to system demands.

Control schematics

Response times of the pump are collected from a

circuit as below by measuring the pumps swash angle

movement at different pressures.

Dynamic characteristic of ﬂow control *

Load Sensing Controls

ST

M

P1 P

AP

T

P A

T

PF

Time on-stroke [ms] Time de-stroke [ms]

stand-by

to 50 bar

stand-by

to 350 bar

50 bar to

stand-by

350 bar to

stand-by

PV360 500 690 830 50

Pressure adjustment range 15 to 350 bar

Factory setting pressure 50 bar

Differential pressure adjustment range 10 to 40 bar

Factory setting differential pressure 10 bar

Control oil consumption Max 8.0 l/min

* Curve shown exaggerated

t on stroke t

de-stroke

Displacement [%]

0

25

50

75

100

Response time

Load valve

23

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

ST

M

P1 P

AP

T

PA

T

PF

T

P

Load Sensing Controls

Control option MF1

With code MF1 the remote pressure control has a

valve interface size NG 6 DIN 24340 (CETOP 03 acc.

RP35H, NFPA D03) on the top side.

This interface allows the mounting of accessories like

multiple pressure selectors without the need of external

piping and valve mounting.

Load Sensing Control with NG6 Interface

ST

M

P1 P

AP

T

PA

T

PF

T

P

Load Sensing Control with Electrical Unloading

Control option MFW

With code MFW a solenoid operated directional control

valve (D1VW002KNJW) for electrical unloading is

mounted on the control top side.

When the solenoid is de-energised, the pump compen-

sates at a stand-by pressure of typically 15 bar. When

the solenoid is energised, the pump compensates at

the pressure adjusted on the integrated pilot valve.

Load Sensing Control with Proportional Pilot Valve

Control option MFK

With code MFK a proportional pilot valve of type

PVACRE..35 (see page 35) is mounted on the top side

interface.

This allows a variation of the pump compensating pres-

sure between 20 and 350 bar by an electrical signal.

Control option MFZ

Control MFZ has no integrated pilot valve but a valve

interface NG6 DIN 24340 on the top.

This version is recommended for valve accessories.

Load Sensing Control with Accessory

ST

M

P1 P

AP

T

PA

T

PF

T

P

ST

M

P1 P

AP

T

PA

T

PF

T

P

24

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

2 Spool Load Sensing Control

Control option MTP

The pilot pressure of the load sensing control is taken from a load sensing port in the hydraulic system. It is used

to match pump ﬂow to system demands. With the 2 spool control the interaction of the two control functions is

avoided by using two separate control valves for ﬂow and pressure compensation.

Control schematics

Response times of the pump are collected from a

circuit as below by measuring the pumps swash angle

movement at different pressures.

Dynamic characteristic of ﬂow control *

Load Sensing Controls

ST

M

P1 P

AP

T

PA

T

PF

P

T

Time on-stroke [ms] Time de-stroke [ms]

stand-by

to 50 bar

stand-by

to 350 bar

50 bar to

stand-by

350 bar to

stand-by

PV360 920 670 1000 170

Pressure adjustment range 15 to 350 bar

Factory setting pressure 50 bar

Differential pressure adjustment range 10 to 40 bar

Factory setting differential pressure

load sensing

10 bar

Factory setting differential pressure,

pressure control

15 bar

Control oil consumption Max 8.0 l/min

* Curve shown exaggerated

t on stroke t

de-stroke

Displacement [%]

0

25

50

75

100

Response time

p

Q

Load valve

25

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Load Sensing Controls

Control option MT1

With code MT1 the remote pressure control has a

valve interface size NG 6 DIN 24340 (CETOP 03 acc.

RP35H, NFPA D03) on the top side.

This interface allows the mounting of accessories like

multiple pressure selectors without the need of external

piping and valve mounting.

2 Spool Load Sensing Control with NG6 Interface

ST

M

P1 P

AP

T

PA

T

P

F

P

T

2 Spool Load Sensing Control with Proportional Pilot Valve

Control option MTK

With code MTK a proportional pilot valve of type

PVACRE..35 (see page 35) is mounted on the top side

interface.

This allows a variation of the pump compensating pres-

sure between 20 and 350 bar by an electrical signal.

Control option MTZ

Control MTZ has a valve accessory factory mounted on

the NG6 interface.

Available valve accessory can be seen on page 33.

Specify the accessory with full ordering code.

2 Spool Load Sensing Control with Accessory

ST

M

P1 P

AP

T

PA

T

P

F

P

T

ST

M

P1 P

AP

T

PA

T

P

F

P

T

26

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Horse Power/Torque Controls with Pressure Control

Control option *LC

The horse power control type *L* provides the beneﬁt of the pressure control, plus the ability to limit the input

power the pump will draw. These controls are beneﬁcial when the power available from the prime mover for the

hydraulics is limited or the application power demand has both high ﬂow/low pressure and low ﬂow/high pressure

duty cycles.

Control schematics

Response times of the pump are collected from a

circuit as below by measuring the pumps swash angle

movement at different pressures.

Dynamic characteristic of ﬂow control *

Horse Power/Torque Controls

ST

M

P1 P

AP

T

P A

T

L

See Horse Power characteristic curves on page 24

Pressure adjustment range 15 to 350 bar

Factory setting pressure 350 bar

Differential pressure adjustment range 10 to 40 bar

Factory setting differential pressure 15 bar

Control oil consumption Max 8.0 l/min

* Curve shown exaggerated

t on stroke t

de-stroke

Displacement [%]

0

25

50

75

100

Response time

Time on-stroke [ms] Time de-stroke [ms]

against

50 bar

against

350 bar

zero stroke

50 bar

zero stroke

350 bar

PV360 90 90 100 100

Load valve

27

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

ST

M

P1 P

AP

T

PA

T

L

P

T

Horse Power/Torque Controls

Control option *L1

With code *L1 the remote pressure control has a

valve interface size NG 6 DIN 24340 (CETOP 03 acc.

RP35H, NFPA D03) on the top side.

This interface allows the mounting of accessories like

multiple pressure selectors without the need of external

piping and valve mounting.

Horse Power/Torque Control with NG6 Interface

ST

M

P1 P

AP

T

PA

T

L

P

T

Horse Power/Torque Control with Electrical Unloading

Control option *LW

With code *LW a solenoid operated directional control

valve (D1VW002KNJW) for electrical unloading is

mounted on the control top side.

When the solenoid is de-energised, the pump compen-

sates at a stand-by pressure of typically 15 bar. When

the solenoid is energised, the pump compensates at

the pressure adjusted on the integrated pilot valve.

Horse Power/Torque Control with Proportional Pilot Valve

Control option *LK

With code *LK a proportional pilot valve of type

PVACRE..35 (see page 35) is mounted on the top side

interface.

This allows a variation of the pump compensating pres-

sure between 20 and 350 bar by an electrical signal.

Control option *LZ

Control *LZ has no integrated pilot valve but a valve

interface NG6 DIN 24340 on the top.

This version is recommended for valve accessories.

Horse Power/Torque Control with Accessory

ST

M

P1 P

AP

T

PA

T

L

P

T

ST

M

P1 P

AP

T

PA

T

L

P

T

28

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Horse Power/Torque Controls with Load Sensing

Control option *CC

The horse power control type *C* provides the beneﬁt of the load sensing control, plus the ability to limit the input

power the pump will draw. These controls are beneﬁcial when the power available from the prime mover for the

hydraulics is limited or the application power demand has both high ﬂow/low pressure and low ﬂow/high pressure

duty cycles.

Control schematics

Response times of the pump are collected from a

circuit as below by measuring the pumps swash angle

movement at different pressures.

Dynamic characteristic of ﬂow control *

Horse Power/Torque Controls

ST

M

P1 P

AP

T

P A

T

L

PF

See Horse Power characteristic curves on page 24

Time on-stroke [ms] Time de-stroke [ms]

stand-by

to 50 bar

stand-by

to 350 bar

50 bar to

stand-by

350 bar to

stand-by

PV360 90 90 100 100

Pressure adjustment range 15 to 350 bar

Factory setting pressure 350 bar

Differential pressure adjustment range 10 to 40 bar

Factory setting differential pressure 15 bar

Control oil consumption Max 8.0 l/min

* Curve shown exaggerated

t on stroke t

de-stroke

Displacement [%]

0

25

50

75

100

Response time

Load valve

29

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

ST

M

P1 P

AP

T

PA

T

L

P

T

PF

ST

M

P1 P

AP

T

PA

T

L

P

T

PF

Horse Power/Torque Controls

ST

M

P1 P

AP

T

PA

T

L

P

T

PF

ST

M

P1 P

AP

T

PA

T

L

P

T

PF

Control option *C1

With code *C1 the remote pressure control has a

valve interface size NG 6 DIN 24340 (CETOP 03 acc.

RP35H, NFPA D03) on the top side.

This interface allows the mounting of accessories like

multiple pressure selectors without the need of external

piping and valve mounting.

Horse Power/Torque Control with NG6 Interface

Horse Power/Torque Control with Electrical Unloading

Control option *CW

With code *CW a solenoid operated directional control

valve (D1VW002KNJW) for electrical unloading is

mounted on the control top side.

When the solenoid is de-energised, the pump compen-

sates at a stand-by pressure of typically 15 bar. When

the solenoid is energised, the pump compensates at

the pressure adjusted on the integrated pilot valve.

Horse Power/Torque Control with Proportional Pilot Valve

Control option *CK

With code *CK a proportional pilot valve of type

PVACRE..35 (see page 35) is mounted on the top side

interface.

This allows a variation of the pump compensating pres-

sure between 20 and 350 bar by an electrical signal.

Control option *CZ

Control *CZ has no integrated pilot valve but a valve

interface NG6 DIN 24340 on the top.

This version is recommended for valve accessories.

Horse Power/Torque Control with Accessory

30

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 140

10

35

45

0

5

15

20

30

40

25

0 100 300

50 150 250200

350

PV023

PV028

PV020

PV016

K=18.5 kW

C=4 kW

D=5.5 kW

H=15 kW

B=3 kW

G=11 kW

E=7.5 kW

20

70

0

10

30

40

60

50

0 100 300

50 150 250200 350

PV046

PV040

PV032

D=5.5 kW

E=7.5 kW

G=11 kW

H=15 kW

M=22 kW

K=18.5 kW

S=30 kW

Typical Horse Power/Torque Control Characteristics

Performance Curves

200

210

180

160

140

120

100

80

60

40

20

0

050 100 150 200 250 300

350

PV140

W=55 kW

T=37 kW

S=30 kW

M=22 kW

K=18,5 kW

Y=75 kW

U=45 kW

Z=90 kW

Flow rate Q [l/min]

Pressure p [bar]

Pressure p [bar] Pressure p [bar]

Flow rate Q [l/min]

Pressure p [bar]

140

120

100

80

60

40

20

0

050 100 150 200 250 300 350

PV092

PV080

PV063

S=30 kW

M=22 kW

K=18,5 kW

G=11 kW

H=15 kW

T=37 kW

W=55 kW

U=45kW

K=18.5 kW

31

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 180 to 360

Typical Horse Power/Torque Control Characteristics

Performance Curves

Flow rate Q [l/min

Pressure p [bar]

0

50

100

150

200

250

300

350

400

450

500

550

0 50 100 150 200 250 300 350

U=45 kW

W=55 kW

Y=75 kW

Z=90 kW

2=110 kW

3=132 kW

4=160 kW

5=180 kW

6=200 kW

PV360

Speed : n = 1500 rev/min

Temperature : t = 50 °C

Fluid : HLP, ISO VG46

Viscosity : ν = 46 mm

2

/s at 40 °C

Pressure : Maximum 350 bar, depending on HP level

300

270

240

210

180

150

120

90

60

30

0

050 100 150 200 250 300

350

PV180

W=55 kW

U=45 kW

T=37 kW

M=22 kW

S=30 kW

Y=75 kW

2=110 kW

Z=90 kW

Flow rate Q [l/min]

Pressure p [bar]

300

350

425

250

200

150

100

50

0

050 100 150 200 250 300

350

PV270

W=55 kW

U=45 kW

T=37 kW

3=132 kW

Y=75 kW

2=110 kW

Z=90 kW

Flow rate Q [l/min]

Pressure p [bar]

32

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Proportional Displacement Control

Control option FPV

The proportional displacement control allows the adjustment of the pumps output ﬂow with an electrical input signal.

The actual displacement of the pump is monitored by an LVDT and compared with the commanded displacement in

an electronic control module PQDXXA-Z00. The command is given as an electrical input signal (0 - 10 V) from the

supervising machine control or a potentiometer.

Version FPV of the proportional control does not provide a pressure compensation. The hydraulic circuit must be

protected by a pressure relief valve.

Control schematics

Response times of the pump are collected from a

circuit as below by measuring the pumps swash angle

movement at different pressures.

Dynamic characteristic of ﬂow control *

Electronic P/Q Controls

Time on-stroke [ms] Time de-stroke [ms]

stand-by

to 50 bar

stand-by

to 350 bar

50 bar to

stand-by

350 bar to

stand-by

PV360 180 100 330 240

Pressure adjustment range * 25 to 350 bar

Factory setting pressure * 50 bar

Differential pressure adjustment range * 10 to 40 bar

Factory setting differential pressure * 15 bar

Control oil consumption Max 8.0 l/min

Internal pilot pressure required to control the pump

FPV 15 bar

UPR 25 bar

UPK 25 bar

UPM 25 bar

ST

M

P1 P

AP

T

PA

T

6

8

* Curve shown exaggerated

* Data valid for UP* version

t on stroke t

de-stroke

Displacement [%]

0

25

50

75

100

Response time

p

Q

U

Q

= FPV included

Load valve

33

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

ST

M

P1 P

AP

T

PA

T

6

8

T

P

Electronic P/Q Controls

ST

M

P1 P

AP

T

PA

T

6

8

P

T

ST

M

P1 P

AP

T

PA

T

6

8

3

8

T

P

Control option UPR

Control version UPR provides electro- hydraulic

displacement control and pressure stage mounted on

an elbow manifold.

The elbow manifold provides NG6/D03 interface on top

to mount a pressure pilot valve (not included in UPR).

Proportional Displacement Control with Overriding Pressure Control

Proportional Displacement Control with Proportional Pressure Control

Control option UPK

When using a proportional pressure pilot valve an

electro-hydraulic p/Q control can be realized. The

proportional pressure pilot valve PVACRE..35 is

included in control version UPK.

By using the digital module PQDXXA-Z00 it is possible

to control the displacement proportionally with over-

riding open loop proportional pressure control.

Proportional Displacement Control with Closed Loop Pressure Control

Control option UPM

Control version UPM is completed by a pressure trans-

ducer Parker SCP 8181 CE. In combination with control

module PQDXXA-Z00 a closed loop pressure control of

pump outlet pressure is available.

The control module also offers an electronic power

limiter in addition to closed loop pressure control with

this control option.

= UPM included

U

P

U

Q

p

34

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 028

0

100

200

300

2

4

6

8

10

12

14

4

0

8

12

16

20

0

100 200300

0

20

40

60

80

100

0

5

10

15

20

25

PV020

5

0

10

15

20

25

0

100 200300

0

20

40

60

80

100

0

6

12

18

24

30

PV023 PV028

5

0

10

15

20

25

0

100 200300

0

20

40

60

80

100

0

8

16

24

32

40

Efﬁciency and case drain ﬂows PV016, PV020, PV023

and PV028

The efﬁciency and power graphs are measured at an

input speed of n = 1500 rpm, a temperature of 50 °C and

a ﬂuid viscosity of 30 mm

2

/s.

Case drain ﬂow and compensator control ﬂow leave via

the drain port of the pump. To the values shown are to

be added 1 to 1.2 l/min , if at pilot operated compensa-

tors the control ﬂow of the pressure pilot valve also goes

through the pump.

Please note: The values shown below are only valid for

static operation. Under dynamic conditions and at rapid

compensation of the pump the volume displaced by the

servo piston also leaves the case drain port. This dynamic

control ﬂow can reach up to 40 l/min! Therefore the case

drain line is to lead to the reservoir at full size and without

restrictions as short and direct as possible.

Case drain ﬂow PV016-028 with pressure

compensator (MMC)

Efﬁciency, power consumption

PV016

Efﬁciency and Case Drain Flows

5

0

10

15

20

25

0

100 200320

0

20

40

60

80

100

0

10

20

30

40

50

Pressure [bar]

full ﬂow

dead head

Drain ﬂow [l/min]

Output ﬂow [l/min]

Input power [kW]

vol. efﬁciency

overall efﬁciency

input power at full ﬂow

input power at deadhead

output ﬂow

output ﬂow, vol. efﬁciency

output ﬂow

Efciency[%](overall,volymetric)

35

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 032 to 046

Efﬁciency and case drain ﬂows PV032 to PV046

The efﬁciency and power graphs are measured at an

input speed of n = 1500 rpm, a temperature of 50 °C and

a ﬂuid viscosity of 30 mm

2

/s.

Case drain ﬂow and compensator control ﬂow leave via

the drain port of the pump. To the values shown are to

be added 1 to 1.2 l/min , if at pilot operated compensa-

tors the control ﬂow of the pressure pilot valve also goes

through the pump.

Please note: The values shown below are only valid for

static operation. Under dynamic conditions and at rapid

compensation of the pump the volume displaced by the

servo piston also leaves the case drain port. This dynamic

control ﬂow can reach up to 60 l/min! Therefore the case

drain line is to lead to the reservoir at full size and without

restrictions as short and direct as possible.

Case drain ﬂow PV032-046 with pressure

compensator (MMC)

Efﬁciency, power consumption

PV032

10

0

20

30

40

50

0

100 200300 350

0

20

40

60

80

100

0

8

16

24

32

40

12

0

24

36

48

60

0

100 200300

350

0

20

40

60

80

100

0

8

16

24

32

40

10

0

20

30

40

50

0

100 200300

350

0

20

40

60

80

100

0

16

32

48

64

80

0

100

200

300

2

10

12

14

4

8

6

PV040

PV046

Efﬁciency and Case Drain Flows

Pressure [bar]

full ﬂow

dead head

Drain ﬂow [l/min]

Output ﬂow [l/min]

Input power [kW]

Input power [kW]Input power [kW]

vol. efﬁciency

overall efﬁciency

input power at full ﬂow

input power at deadhead

output ﬂow

output ﬂow, vol. efﬁciency

output ﬂow

Efciency[%](overall,volymetric)

36

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 063 to 092

Case drain ﬂows PV063-092

Efﬁciency, power consumption

PV063

Efﬁciency and case drain ﬂows PV063, PV080, PV092

The efﬁciency and power graphs are measured at an

input speed of n = 1500 rpm, a temperature of 50 °C and

a ﬂuid viscosity of 30 mm

2

/s.

Case drain ﬂow and compensator control ﬂow leave via

the drain port of the pump. To the values shown are to be

added 1 to 1.2 l/min , if at pilot operated compensators

(codes FR*, FF*, FT*, power compensator and p-Q-

control) the control ﬂow of the pressure pilot valve also

goes through the pump.

Please note: The values shown below are only valid for

static operation. Under dynamic conditions and at rapid

compensation of the pump the volume displaced by the

servo piston also leaves the case drain port. This dynamic

control ﬂow can reach up to 80 l/min! Therefore the case

drain line is to lead to the reservoir at full size and without

restrictions as short and direct as possible.

14

0

28

42

56

70

0 100 200300

0

20

40

60

80

100

0

20

40

60

80

100

16

0

32

48

64

80

0 100 200300

0

20

40

60

80

100

0

24

48

72

96

120

20

0

40

60

80

100

0 100 200300

0

20

40

60

80

100

0

30

60

90

120

150

12

8

4

0

0 100 200

300

PV080

PV092

Efﬁciency and Case Drain Flows

Pressure [bar]

full ﬂow

dead head

Drain ﬂow [l/min]

Pressure [bar]

Output ﬂow [l/min]

Output ﬂow [l/min]Output ﬂow [l/min]

Input power [kW]

vol. efﬁciency

overall efﬁciency

input power at full ﬂow

input power at deadhead

output ﬂow

output ﬂow, vol. efﬁciency

output ﬂow

Efciency[%](overall,volymetric)

37

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 140 to 180

Efﬁciency and case drain ﬂows PV140, PV180

The efﬁciency and power graphs are measured at an

input speed of n = 1500 rpm, a temperature of 50 °C and

a ﬂuid viscosity of 30 mm

2

/s.

Case drain ﬂow and compensator control ﬂow leave via

the drain port of the pump. To the values shown are to

be added 1 to 1.2 l/min, if at pilot operated compensa-

tors the control ﬂow of the pressure pilot valve also goes

through the pump.

Please note: The values shown below are only valid for

static operation. Under dynamic conditions and at rapid

compensation of the pump the volume displaced by the

servo piston also leaves the case drain port. This dynamic

control ﬂow can reach up to 120 l/min! Therefore the case

drain line is to lead to the reservoir at full size and without

restrictions as short and direct as possible.

Efﬁciency, power consumption

PV140

Case drain ﬂows PV140-180

30

0

60

90

120

150

0 100 200300

0

20

40

60

80

100

0

50

100

150

200

250

35

0

70

105

140

175

0 100 200300

0

20

40

60

80

100

0

60

120

180

240

300

18

12

6

0

0 100 200

300

PV180

Efﬁciency and Case Drain Flows

Pressure [bar]

Output ﬂow [l/min]Output ﬂow [l/min]

Input power [kW]

vol. efﬁciency

overall efﬁciency

input power at full ﬂow

input power at deadhead

output ﬂow

Efciency[%](overall,volymetric)

Pressure [bar]

full ﬂow

dead head

Drain ﬂow [l/min]

38

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Efﬁciency and case drain ﬂows PV270

The efﬁciency and power graphs are measured at an

input speed of n = 1500 rpm, a temperature of 50 °C and

a ﬂuid viscosity of 30 mm

2

/s.

Case drain ﬂow and compensator control ﬂow leave via

the drain port of the pump. To the values shown are to be

added 1 to 1.2 l/min , if at pilot operated compensators

(codes FR*, FF*, FT*, power compensator and p-Q-

control) the control ﬂow of the pressure pilot valve also

goes through the pump.

Please note: The values shown below are only valid for

static operation. Under dynamic conditions and at rapid

compensation of the pump the volume displaced by the

servo piston also leaves the case drain port. This dynamic

control ﬂow can reach up to 120 l/min! Therefore the case

drain line is to lead to the reservoir at full size and without

restrictions as short and direct as possible.

Efﬁciency, power consumption

PV270

50

0

100

150

200

250

0 100 200300

0

20

40

60

80

100

0

100

200

300

400

500

24

16

8

0

0 100 200

300

Case drain ﬂows PV270

Efﬁciency and Case Drain Flows

Pressure [bar]

Output ﬂow [l/min]

Input power [kW]

vol. efﬁciency

overall efﬁciency

input power at full ﬂow

input power at deadhead

output ﬂow

Efciency[%](overall,volymetric)

Pressure [bar]

full ﬂow

dead head

Drain ﬂow [l/min]

Axial Piston Pump

PV 270

39

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 360

Performance Curves

Typical efﬁciency at full displacement and

1500 rpm

The curves show typical characteristics measured under

following conditions:

Fluid: Mineral oil ISO VG 22 at 32 °C

Inlet pressure 1,0 bar (absolute), measured at inlet port.

60%

70%

80%

90%

100%

0255075 100 125150 175200 225250 275300 325350

Volumetric

Overall

Pressure [bar]

Efciency[%]

1500

1550

1600

1650

1700

1750

1800

1850

0.80.9 1.01.1

Typical inlet characteristics vs. speed at

various percentage displacements

Inlet characteristics

Displacement

95%100%

Inlet pressure [bar]

Self priming speed [rpm]

0

50

100

150

200

250

300

350

400

0255075 100 125 150175 200225 250275 300325 350

0

5

10

15

20

25

30

35

0255075 100 125 150 175 200 225 250 275 300 325 350

Typical drive power at full displacement

Input power – full stroke

Typical compensated power

Input power – zero stroke

1750 rpm

1500 rpm

Pressure [bar]

Input power [kW]Input power [kW]

Case drain ﬂows

Pressure [bar]

Drain ﬂow [l/min]

24

32

40

16

8

0

0 100 200

300360

full ﬂow

dead head

40

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

48

133

48

133

48

133

High

pressure

High

pressure

Low

pressure

Low

pressure

DC solenoid 205

AC solenoid 190

DC solenoid 205

AC solenoid 190

DC solenoid 241

AC solenoid 211

Code Seals

N NBR

V FPM

AC

PV

Function

SolenoidFor

PV pump

series

Adjustment

Seals

Accessories

for

controls

Solenoid

acces-

sories

Mounting

bolts

Nominal

pressure

350 bar

35

Code Function

1P Max. pressure relief

1E 1 pressure,

electrical unloading

stand by default

2P 2 pressures,

electrical selection

2 pressures + stand by

2E electrical selection

low pressure default

2 pressures + stand by

2M electrical selection

stand by default

Code Mounting bolts

C For single controls

S Without bolts

M For code UP*/MT*

Code Solenoid accessories

omit For function 1P

W DIN plug socket

without plug

Code Solenoid voltage

omit For function 1P

Y 110V/50Hz - 120V/60Hz

T 220V/50Hz - 240V/60Hz

J 24V DC

Code Adjustment

S Spindle

with lock nut

PVAC2P* PVAC2M*/PVAC2E*

PVAC1E*

PVAC1P*

Dimensions

Code Threads

M Metric

S SAE / UNC

Threads

Accessories Control

Adjustment

Code S

41

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Accessories Control

Schematics PVAC1P*

Schematics PVAC1E*

Schematics PVAC2P* Schematics PVAC2M*/PVAC2E*

*2M*

42

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Accessories Control

Technical data

General

Nominal size DIN NG06 / CETOP03 / NFPA D03

Mounting position as desired, horizontal mounting preferred

Ambient temperature [°C] -20 ... +70

Weight [kg] 1.8

Hydraulic

Max. operating pressure [bar] Ports P and A up to 420; port T depressurized

Pressure stages [bar] 350, 420

Fluid Hydraulic oil as per DIN 51524 ... 525

Viscosity, recommended [cSt] /

permitted [cSt] /

[mm²/s]

30 ... 80

12 ... 380

Fluid temperature [°C] -20 ... +60

Filtration ISO 4406 (1999), 18/16/13

Linearity [%] ±2.8

Repeatability [%] <±1

Hysteresis [%] ±1.5 of p

max

Electrical

Duty ratio [%] 100 ED

Protection class IP 65 in accordance with EN 60529 (plugged and mounted)

Nominal voltage [V] 16 (1.3 A max. current)

Coil resistance [Ohm] 4 at 20°C

Solenoid connection Connector as per EN 175301-803

Power ampliﬁer, recommended PCD00A-400

Proportional pressure relief valve PVACRE*

Function

When the pressure in port P exeeds the pressure setting

at the solenoid, the poppet opens to port T and limits the

pressure in port P to the adjusted level.

The optimum performance can be achieved in combina-

tion with the digital ampliﬁer module PCD00A-400 (see

catalogue HY11-3500 for reference).

43

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Ordering code proportional pressure relief valve

Schematic PVACRE*

Dimensions PVACRE*

Code Seal

N NBR

V FPM

AC

PV

Prop.

pressure

valve

Pump

series PV

Seal

Accessories

for controller

RE

Code Nominal pressure

35 350 bar

42 420 bar

Nominal

pressure

Mounting

bolts

Thread

option

Code Thread option

M Metric

S SAE / UNC

Code Mounting bolts/

ports

C For single controller

S Without bolts

M For code UP*/MT*

design series 45/46

Accessories Control

Example for PVACRE* mounted

ST

M

P1 P

AP

T

PA

T

P

1/16" NPT

(for P, T)

44

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 028

Dimensions

max. 212

13

52

Ø25

k6

Ø100

h8

131

32

10

94

219

79

132

max. 130

12

125

55

48

15

50

X

119

43

Ø100

h8

90

PV016 - 028, metric version

Shown is a clockwise rotating pump with standard pressure compensator.

Counter clockwise rotating pumps have inlet, outlet and gauge port reversed.

Interface for

horse power pilot cartridge

or LVDT for

displacement feedback

Drain port L1; G1/2

optional M22x1.5; ISO 6149-1

(thread options 7 and 8)

or 7/8-14 UNF

(thread option 3)

view X

Gage port M; G1/4

optional M12x1.5; ISO 6149-1

(thread options 7 and 8)

or 7/16-20 UNF

(thread option 3)

key

8x7x40

DIN 6885

thread M10,

22 deep

Drain port L2 and

L3 (opposite); G1/2

optional M22x2; ISO 6149-1

(thread options 7 and 8)

or 7/8-14 UNF

(thread option 3)

OUTLET for metric and

SAE version:

ﬂage acc. ISO 6162

DN19; PN400

INLET for metric and

SAE version:

ﬂage acc. ISO 6162

DN32; PN250

4xM10, 18 deep

optional 3/8-16UNC-2B

(thread options 3 and 7)

4xM10, 18 deep

optional 7/16-14UNC-2B

(thread options 3 and 7)

Mounting optional L

splined shaft W25x1.5x15x8f

DIN 5480

The pump shown above has mounting option K

and thru drive option T

(prepared for thru drive)

197.5

9.0

28

-0.25

170.5

162.5

50.8

23.8

30.2

58.7

45

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 028

A

B

27

47

G

E

D

F

C

Dimensions

Variation with thru drive

PV016 - 028, SAE version

46

50

Key:

6.35 x 6.35

40 long

Thread:

3/8-16UNC-2B

22 deep

Shown above is

Mounting option D

Mounting option E

Splined shaft 15T-16/32 DP,

ﬂat root, side ﬁt ANSI B92.1

Thru drive:

splined shaft

13T-16/32 DP,

ﬂat root, side ﬁt

9.4

Ø25.4

-0.05

Ø28.2 ±0.15

Ø101.6

-0.05

Ø101.6

-0.05

197.5

(224.5)

89.9

44.9

13.5

Thru drive adaptors are available with the following dimensions

Drawing Dimension

Thru drive option

A B C D E F G Remark

Metr UNC Metr UNC

Y 50.8 8 - - - - 82 M8 5/16"-18 SAE AA 2-Bolt

A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-Bolt

B 101.6 10.5 127 89.8 M12 1/2"-13 - - - SAE B 4-Bolt

G 63 8.5 85 60.1 M8 5/16"-18 100 M8 5/16"-18 2/4-Bolt

H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-Bolt

J 100 10,5 125 88.4 M10 3/8"-16 - - - 4-Bolt

46

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 032 to 046

PV032 - 046, metric version

Dimensions

68

10

9

16

227

max 248

Ø125

h8

Ø125

h8

Ø32

k6

149

138

185

197

71

60

50

99

160

14

97

160

max 130

47

X

PVCMMCN Serie 45

Code AM 350bar

Interface for power pilot

cartridge or LVDT for

displacement feedback

Drain port L1; G3/4

optional M27 x 2; ISO 6149-1

(thread options 7 and 8)

or 1 1/16-12 UNF

(thread option 3)

view X

Gage port M; G1/4

optional M12x1,5; ISO 6149-1

(thread options 7 and 8)

or 7/16 - 20 UNF

(thread option 3)

Drain ports L2 and L3

(opposite); G3/4

optional M27 x 2: ISO 6149-1

(thread options 7 and 8)

or 1 1/16 - 12 UNF

(thread option 3)

Thread M10,

22 deep

Key

10 x 8 x 56

DIN 6885

Mounting optional L

splined shaft W32x1,5x20x8f

DIN 5480

OUTLET for metric and

SAE version:

ﬂange acc. ISO 6162

DN25; PN400

4 x M12, 18 deep

optional 7/16-14 UNC-2B

(thread options 3 and 7)

INLET for metric and

SAE version:

ﬂange acc. ISO 6162

DN38; PN200

4 x M12, 18 deep

optional 1/2-13 UNC-2B

(thread options 3 and 7)

mounting option K

Shown is a clockwise rotating pump with standard pressure compensator.

Counter clockwise rotating pumps have inlet, outlet and gauge port reversed.

36.5

255.5

112.5

35

-0.25

57.2

27.8

69.9

35.7

47

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 032 to 046

At threads options 3 and 7 the dimensions E and G are UNC - 2B threads.

Variation with thru drive

Dimensions

227

L

K

B

A

D

F

E

G

ØC

Thru drive:

splined shaft

W25x1,5x15x8f

DIN 5480

PV032 - 046, SAE version

56

8

60

68

14

8

Key:

7.94 x 7.94

56 long

Thread:

3/8-16UNC-2B

22 deep

Shown above is

Mounting option D

Mounting option E

Splined shaft 14T-12/24 DP,

ﬂat root, side ﬁt ANSI B92.1

114.5

57.25

Ø32.5

±0.13

Ø127

-0.05

Ø127

-0.05

Ø31.75

-0.05

12.7

Thru drive adaptors are available with the following dimensions

Drawing Dimension

Thru drive option

A B C D E F G K L Remark

Metr UNC Metr UNC

A 82.55 8 - - - - 106 M10 3/8"-16 48 261 SAE A 2-Bolt

B 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 48 261 SAE B 2/4-Bolt

C 127 13.5 162 114.6 M12 1/2"-13 - - - 63 276 SAE C 4-Bolt

G 63 8.5 85 60.1 M8 5/16"-18 100 M8 5/16"-18 48 261 2/4-Bolt

H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 48 261 2/4-Bolt

J 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 48 261 2/4-Bolt

K 125 10.5 160 113.1 M12 1/2"-13 - - - 48 261 4-Bolt

48

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

236

252

32

50

178

132120

196

Ø160

h8

Ø40 k6

200

92

9

20

9

10

287

86

78

64

26

56

Ø160 h8

18

Ø200

121

X

Dimensions

PV 063 - 092 Metric

Mounting interface for

horse power pilot or LVDT

for displacement feedback

Gage port M; G1/4, optional M12 x 1.5; ISO

6149-1 (tread option 7 and 8) or 7/16- 20 UNF

(tread option 3)

Drain ports L1, L2 and L3; G3/4”

optional M27 x 2; ISO 6149-1

(tread option 7 and 8)

or 1 1/16 - 12 UNF

(tread option 3)

4 x M12, 20 deep

optional 1/2 - 13 UNC - 2B

(thread options 3 and 7)

4 x M12, 20 deep

optional 1/2 - 13 UNC - 2B

(thread options 3 and 7)

or thread options 4:

4 x M14, 20 deep

INLET for metric and SAE

version:

ﬂange according ISO 6162

DN 51; PN 200 bar

OUTLET for metric and SAE version:

ﬂange according ISO 6162

DN 32; PN 400 bar

77.8

66.6

42.9

31.8

187.5

Max. 308

Max. 133

Key 12 x 8 x 80

DIN 6885

Shown with standard

pressure control

The pump shown above has Mounting option K

and through drive variation T

(prepared for through drive)

Mounting option L, splined shaft

W40 x 1.5 x 25 x 8f DIN 5480

Thread

M12 - 28 deep

view X

43

-0.25

Axial Piston Pump

PV 063 to 092

49

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 063 to 092

Dimensions

PV 063 - 092 SAE Version

8

82

90

75

287

L

K

B

A

D

F

G

E

C

Key: 11.11x11.11

80 long

Thread

1/2-13

UNC-2B

28 deep

Mounting option E

splined shaft 13T-8/16 DP,

ﬂat root, side ﬁt ANSI B92.1

Output: splined shaft

W50x2x24x9g DIN 5480

Shown above is

Mounting option D

Variation with thru drive

Ø152.4

Ø44.45

-0.05

49.3

-0.05

12.6

20.6

80.8

161.6

Ø152.4

-0.05

Thru drive adaptors are available with the following dimensions

Drawing Dimension

Thru drive option

A B C D

E

F G K L Remark

Metr UNC

A 82.55 8 - - - - 106 M10 3/8"-16 58 326 SAE A 2-Bolt

B 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 58 326 SAE B 2/4-Bolt

C 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 58 326 SAE C 2/4-Bolt

D 152.4 13.5 228.5 161.6 M16 5/8"-11 - - - 83 351 SAE D 4-Bolt

G 63 8.5 85 60.1 M8 5/16"-18 100 M8 5/16"-18 58 326 2/4-Bolt

H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 58 326 2/4-Bolt

J 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 58 326 2/4-Bolt

K 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 58 326 2/4-Bolt

L 160 13.5 200 141.4 M16 5/8"-11 - - - 58 326 4-Bolt

50

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 140 to 180

350

20

48

92

10

Ø50 k6

Ø160 h8

97

202

182

158

145

200

35

283

230

106

105

146

63

32

78

Ø160 h8

40

Ø200

18

Dimensions

PV 140 - 180 Metric

Mounting interface for

horse power pilot or

LVDT for displacement

feedback

Gage port M; G1/4,

optional M12 x 1.5; ISO 6149-1

(tread option 7 and 8)

or 7/16- 20 UNF (tread option 3)

Drain ports L2; G1"

optional M33 x 2; ISO 6149-1

(tread option 7 and 8)

or 1 5/16 - 12 UNF

(tread option 3)

Drain ports L3,

dimensions see L2

4 x M12, 20 deep

optional 1/2 - 13 UNC - 2B

(thread options 3 and 7)

4 x M12, 20 deep

optional 1/2 - 13 UNC - 2B

(thread options 3 and 7)

or thread options 4:

4 x M14, 22 deep

INLET for metric and SAE

version:

ﬂange according ISO 6162

DN 64; PN 160 bar

OUTLET for metric and SAE

version:

ﬂange according ISO 6162

DN 32; PN 400 bar

Key 14 x 9 x 75

DIN 6885

Thread

M16 - 36 deep

The pump shown above has Mounting option K

and through drive variation T

(prepared for through drive)

Mounting option L,

splined shaft

W50x2x24 x 9g DIN 5480

Bearing ﬂushing port F; G1/4,

optional M12 x 1.5; ISO 6149-1

(tread option 7 and 8)

or 7/16 - 20 UNF

(tread option 3)

Pressure port: 295

Suction port: 305

15.4

53.5

-0.25

Max. 386

Max. 133

9.3

Shown is a clockwise rotating pump with standard pressure control.

Counter clockwise rotating pump have inlet, outlet and gauge port reversed.

31.8

50.8

88.966.6

9.3

51

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 140 to 180

Dimensions

PV 140 - 180 SAE Version

(415)

350

97

65

B

A

E

G

C

D

F

88

75

8

21

Key: 12.7x12.7

75 long

Key: 11.11x11.11

55 long

Thread

5/8-11 UNC-2B

25 deep

Thread

1/2-13 UNC-2B

25 deep

Mounting option E

splined shaft 15T-8/16 DP,

ﬂat root, side ﬁt ANSI B92.1

Mounting option G

splined shaft 13T-8/16 DP,

ﬂat root, side ﬁt ANSI B92.1

Output: splined shaft

W40x1.5x25x8f DIN 5480

Shown above is

Mounting option D

Variation with thru drive

Ø152.4

-0.05

Ø152.4

-0.05

Ø44.45

-0.05

Ø50.8

-0.05

Ø152.4

-0.05

Ø152.4

-0.05

Mounting option F

49.3 ±0.13

56.4 ±0.13

80.8

161.6

12.3

91.4

99.4

Thru drive adaptors are available with the following dimensions

Drawing Dimension

Thru drive option

A B C D E F G Remark

Metr UNC Metr UNC

A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-Bolt

B 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 SAE B 2/4-Bolt

C 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 SAE C 2/4-Bolt

D 152.4 13.5 228.5 161.6 M16 5/8"-11 - - - SAE D 4-Bolt

H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-Bolt

J 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 2/4-Bolt

K 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 2/4-Bolt

L 160 13.5 200 141.4 M16 5/8"-11 - - - 4-Bolt

52

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 270

Dimensions

PV 270 Metric

250

265

176

184

230

60

9

10

25

115

Ø65 k6

Ø200 h8

294

378

403

128

110100

173

135

22

Ø250

80

200

38

88

Mounting interface for

horse power pilot or LVDT

for displacement feedback

Key 18 x 11 x 98

DIN 6885

Gage port M; G1/4,

optional M12 x 1.5; ISO 6149-1 (tread option 7 and 8)

or 7/16- 20 UNF (tread option 3)

Shown with standard

pressure control

The pump shown above has Mounting option K

and through drive variation T

(prepared for through drive)

Mounting option L, splined shaft

W60 x 2 x 28 x 9g DIN 5480

Thread

M20 - 42 deep

Drain ports L1; G1 1/4”

optional M42 x 2; ISO 6149-1

(tread option 7 and 8)

or 1 5/8 - 12 UNF

(tread option 3)

Bearing ﬂushing port F; G1/4,

optional M12 x 1.5; ISO 6149-1

(tread option 7 and 8)

or 7/16 - 20 UNF

(tread option 3)

4 x M16, 30 deep

optional 5/8 - 11 UNC - 2B

(thread options 3 and 7)

4 x M16, 30 deep

optional 5/8 - 11 UNC - 2B

(thread options 3 and 7)

INLET for metric and SAE

version:

ﬂange according ISO 6162

DN 89; PN 35 bar

OUTLET for metric and

SAE version:

ﬂange according ISO 6162

DN 38; PN 400 bar

view X

X

120.7

36.7

79.4

69.8

472.5

Max 510

53

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 270

Dimensions

Variation with thru drive

PV 270 SAE Version

8

88

C

D

F

E

G

A

B

98

Key: 12.7x12.7

75 long

Thread

5/8-11

UNC-2B

25 deep

Mounting option E

splined shaft 15T-8/16 DP,

ﬂat root, side ﬁt ANSI B92.1

Output: splined shaft

W50x2x24x9g DIN 5480

89.5

15.9

97.5

112.25

224.5

112.25

224.5

Ø20.5

Ø50.8

-0.05

56.4 ±0.13

Ø165.1

-0.05

Ø165.1

-0.05

Shown above is

Mounting option D

472.5

531.5

Thru drive adaptors are available with the following dimensions

Drawing Dimension

Thru drive option

A B C D E F G Remark

Metr UNC Metr UNC

A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-Bolt

B 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 SAE B 2/4-Bolt

C 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 SAE C 2/4-Bolt

D 152.4 13.5 228.5 161.6 M16 5/8"-11 229 M16 5/8"-11 SAE D 2/4-Bolt

E 165.1 17 317.5 224.5 M20 3/4"-10 - - - SAE E 4-Bolt

H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-Bolt

J 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 2/4-Bolt

K 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 2/4-Bolt

L 160 13.5 200 141.4 M16 5/8"-11 224 M20 3/4"-10 2/4-Bolt

M 200 13.5 250 176.8 M20 3/4"-10 - - - 4-Bolt

54

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 360

Dimensions

PV 360 Metric

Ø70

m7

Ø250

h8

265

230

184

176

25

60

L2

L3

L1

9

115

9

10

477

max. 510

250

max. 133

128

117

100

294

377

408

X

38

102

173

2

6

315

24

280

224

h8

Ø250

h8

(L)

Ø224

h8

(T)

80

90

Mounting interface for

horse power pilot

or LVDT for

displacement feedback

Key 20 x 12 x 100

DIN 6885

Gauge port M; G1/4, optional

7/16- 20 UNF (tread option 3)

Shown with standard

pressure control

The pump shown above has Mounting option K

and through drive variation T

(prepared for through drive)

Mounting option L, T, splined shaft

W 70 x 3 x 22 x 8f DIN 5480

mounting option R

pilot diameter Ø224 mm

Thread

M20 - 42 deep

Thread

M20 - 42 deep

Drain ports L1, L2 and L3; G1 11/4"

optional 1 5/8 - 12 UNF

(thread option 3)

Bearing ﬂushing port L4; G1/4,

optional 7/16 - 20 UNF

(thread option 3)

4 x M16, 30 deep

optional 5/8 - 11 UNC - 2B

(thread option 3)

4 x M16, 30 deep

optional 5/8 - 11 UNC - 2B

(thread option 3)

INLET for metric and

SAE version:

ﬂange according ISO 6162

DN 102; PN 35 bar

4"

OUTLET for metric and

SAE version:

ﬂange according ISO 6162

DN 38; PN 400 bar

1 1/2"

view X

79.4

36.5

77.8

130.2

resp.

74.5

-0.25

55

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 360

Dimensions

PV 360 SAE Version

92

100

21

10

90

A

D

F

G

E

C

A

B

59

97

477

(536)

78

-0.25

Ø69.85

-0.05

Key:

19.05x19.05

88.9 long

Ø165.1

-0.05

Thread

5/8-11

UNC-2B

36 deep

15.6

112.25

224.5

Note:

The dimensions shown conform to ISO 3019/1

the actual hole dimensions conform to ISO 3019/2

(pitch Ø315, hole Ø26, see previous page)

and cover ISO 3019/1 dimensions as well.

Use washers when assembling pump.

165.1

-0.05

Mounting option E

splined shaft W 70x3x22x8f,

DIN 5480

Output: splined shaft

W 50x2x24x9g DIN 5480

Shown above is

Mounting option D

Variation with thru drive

Thru drive adaptors are available with the following dimensions

Drawing Dimension

Thru drive option

A B C D E F G Remark

Metr UNC Metr UNC

A 82.55 8 - - - - 106 M10 3/8"-16 SAE A 2-Bolt

B 101.6 11 127 89.8 M12 1/2"-13 146 M12 1/2"-13 SAE B 2/4-Bolt

C 127 13.5 162 114.6 M12 1/2"-13 181 M16 5/8"-11 SAE C 2/4-Bolt

D 152.4 13.5 228.5 161.6 M16 5/8"-11 229 M16 5/8"-11 SAE D 2/4-Bolt

E 165.1 17 317.5 224.5 M20 3/4"-10 - - - SAE E 4-Bolt

H 80 8.5 103 72.8 M8 5/16"-18 109 M10 3/8"-16 2/4-Bolt

J 100 10.5 125 88.4 M10 3/8"-16 140 M12 1/2"-13 2/4-Bolt

K 125 10.5 160 113.1 M12 1/2"-13 180 M16 5/8"-11 2/4-Bolt

L 160 13.5 200 141.4 M16 5/8"-11 224 M20 3/4"-10 2/4-Bolt

M 200 13.5 250 176.8 M20 3/4"-10 - - - 4-Bolt

56

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Dimensions standard pressure control, code ...MMC

Control Dimensions

45

73

max. 172

46

41

24

45

54

P

T

L

A

max. 172

41

24

45

L

P

T

A

Pump axis

Controls with code ...MM1 have a NG6 / Cetop 3 interface topside (as shown below)

Dimensions remote pressure and load sensing control, codes ...MR1, ...MF1

Pump axis

Controls with code ...MRC and MFC have no topside

valve interface (as shown above)

Dimensions horse power pilot cartridge, displacement sensor

remote control port p

P

(code ...MRC, ...MR1) resp.

LS port p

F

(code ...MFC, ...MF1)

Pump housing

All control ports G1/4

Optional 7/16-20 UNF (option 3)

69.5

43.4

88.5

37.5

57

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Dimensions for controls with unloading valve, codes ...M*W

Dimensions for controls with proportional pressure pilot valve, codes ...M*K

Control Dimensions

171

130

96

173

97

41

Pump axis

remote control port p

P

resp. LS port p

F

remote control port p

P

resp. LS port p

F

unloading valve:

D1VW002K*JW;

* for seals option

Shown in version MRW/MFW, version MMW has no remote control port.

pilot valve:

PVACREC**35 for codes ...M*K,

** for threads and seals option

Shown in version MRK/MFK, version MMK has no remote control port.

Dimensions for horse power compensator *L* and *C* are identical to MM* respectively MF*.

All control ports G1/4

Optional 7/16-20 UNF

(option 3)

43.4

58

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Control Dimensions

58

29

96

105

81

116

88

110

222

58

104

29

191

96

110

88

Pump axis

Dimensions two spool load sensing control, code ...MT1, ...MTP

LS port p

F

LS port p

F

pressure pilot valve

PVAC1PC**S35

(code ...MTP only)

pressure control

stage

elbow manifold

displacement

control stage

displacement

control stage

Dimensions two spool load sensing control with proportional pressure pilot valve, code ...MTK

pilot valve:

PVACREM**35 for code ...MTK,

** for threads- and seals soption

proportional

pressure pilot valve

pressure control

stage

80.5

59

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

58

105

29

81

116

222

110

91

96

110

Axial Piston Pump

PV 016 to 360

Control Dimensions

pump axis

Dimensions proportional p/Q-control, codes ...UPR, ...UPK, ...UPM

pilot valve:

PVACREM**35 for code ...UPK, UPM

** for threads- and seals option

pressure pilot valve

(codes ...UPK, ...UPM only

pressure sensor

(code ...UPM only)

pressure

control stage

elbow manifold

displacement

control stage

Dimensions proportional displacement control, code ...FPV

pump axis

95 108

50

61

45

60

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Features

• Digitalcontrolcircuit

• ParametersettingviaRS-232orUSBinterface

• Allsettings(ramps,MIN/MAX,controlparameters)can

be stored digitally and recalled from a PC to duplicate

settings to other modules

• Ramptimeupto60seconds

• CompatibletotherelevanteuropeanEMCspecica-

tions

• EasytousePCbasedsetupsoftware

• Coversalldisplacements

• Coversallavailablefunctions

Technical data

Mounting style Snap-on mounting for EN50022 rail

Body material Polycarbonate

Inﬂammation class V2...V0 acc. UL 94

Mounting position any

Env. temperature range [°C] -20...+55

Protection class IP 20 acc. DIN 40 050

Weight [g] 160

Dutyratio [%] 100

Supplyvoltage [V] 18...30VDC,ripple<5%eff.

Rush in current [A] 22 for 0.2 ms

Current consumption [A] < 4 for p/Q control ; < 2 for Q-control

Resolution [%] 0.025(power0.1)

Interface RS232C, 9600 baud, 3.5 mm cinch

EMC EN 50 081-2, EN 50 082-2

Connctors Screw terminals 0.2...2.5 mm², plug in style

Cables [mm²] Supply and solenoid cables; 1,5 mm

2

(AWG16) overall braid shield.

Sensor and command signals; 0,5 mm

2

(AWG20) overall braid shield

Max. cable length [m] 50

For programming the module via PC, an interface cable is needed,

please order part number PQDXXA-KABEL (RS232) or PQDXXA-KABEL-USB (USB) separately.

Ordering code

Option

For all frame

sizes series PV

Digital control

module for p/Q

control

Version A

PQD

XX A

Z00

Electronic Module PQDXXA

Programming software

The programming of the p/Q control module is done in an

easy to learn mode. To select the pump model and size

and to set the control paramters the program ProPVplus

must be started. This program runs under WINDOWS®

95 and higher.

The latest version of this software can be downloaded at

the following internet address:

www.parker.com/euro_pmd

Features

• Displayanddocumentationofparametersets

• Saveondreloadofoptimizedparametersets

• Offersoscilloscopefunctionforeasyperformanceevalu-

ation and optimization

• ParametersetsforallPVpluspumpsarepre-installed

in the modules

61

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Through Drive, Mounting Kits

Code Second pump, SAE

T Prepared for thru drive option (plugged)

Y SAE AA, diameter 50.8 mm

A SAE A, diameter 82.55 mm

B SAE B, diameter 101.6 mm

C SAE C, diameter 127,mm

D SAE D, diameter 152.4 mm

E SAE E, diameter 165.1 mm

Second pump, metric

H Diameter 80 mm

J Diameter 100 mm

K Diameter 125 mm

L Diameter 160 mm

M Diameter 200 mm

SealsSecond pump

Thread

PV

MK

Axial

piston

pump

series PV

BG

Size

Code Seals

N NBR

V FPM

1

2

Mounting

kit

Code Thread

M Metric

S SAE

PV

MK

Axial

piston

pump

series PV

BG

SizeMounting

kit

Coupling

Mounting kits for multiple pumps, for second pump option

Mounting kits for multiple pumps, couplings

Code Pump size

1 Pump size 1: PV016 - PV028

2 Pump size 2: PV032 - PV046

3 Pump size 3: PV063 - PV092

4 Pump size 4: PV140 - PV180

5 Pump size 5: PV270 - PV360

Kit contains positions 30, 69, 84,

85 and 87, see drawing below.

Code Pump size

1 Pump size 1: PV016 - PV028

2 Pump size 2: PV032 - PV046

3 Pump size 3: PV063 - PV092

4 Pump size 4: PV140 - PV180

5 Pump size 5: PV270 - PV360

Code Coupling for metric,

splined shaft DIN 5480

01 N25 x 1.5 x 15

02 N32 x 1.5 x 20

03 N40 x 1.5 x 25

04 N50 x 2 x 24

05 N60 x 2 x 28

06 N70 x 3 x 22*

Coupling for SAE splined shaft

ﬂat root, side ﬁt

11 SAE A, 9T 16/32

12 SAE-, 11T 16/32

13 SAE B, 13T 16/32

14 SAE B-B, 15T 16/32

15 SAE C, 14T 12/24

16 SAE C-C, 17T 12/24

17 SAE D+E, 13T 8/16

18 SAE F, 15T 8/16

Coupling + adaptor

for keyed shaft

20 Diameter 12 mm

21 Diameter 16 mm

22 Diameter 18 mm

* For PV360 only

Kit contains positions 1 (and 2 for keyed shaft).

K

SAE,

splined

keyed shaft

(only up to Ø18,

metric)

metric

splined

second pump

front pump

Availability of thru drive ﬂange and coupling please check with ordering code options per each pump size, starting at page 6

62

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Through Drive, Flange Load Limitation

L1

L2

L3

W1

W2

W3

L

P

Multiple Pump Combinations - Maximum Moment

Combinations of multiple pumps might require additional pump support to avoid a too high stress on the front mounting

ﬂange. Combinations of two PVplus pumps in the same frame size generally do not need additional support in an

industrial application. For combinations of more pumps support is requiered.

In case of combinations of a PVplus pump with another type of pump it is recommended to calculate the moment

for the combination and compare with the maximum moment in table 1 below.

Moment M = (L1

*

W1 + L2

*

W2 + L3

*

W3 +...)

Note:

If the calculated moment M exceed the maximum moment in table 1 below, additional pump support is needed

Table 1: Maximum Moment and Pump Dimensions

PV016-PV028 PV032-PV046 PV063-PV092 PV140-PV180 PV270 PV360

Maximum moment

1)

[Nm] 81 151 401 591 1686 1686

Weight W [N] 186 294 589 883 1687 1766

Distance L1 [mm to C/G] 106 119 178 184 234 238

Distance Lp [mm] 197.5 227 287 350 472.5 477

1) at dynamic weight acceleration 10g = 98.1 m/sec

2

Table 2 Through Drive Adapter Plate Thickness [mm]

Adapter option

2)

PV016-PV028 PV032-PV046 PV063-PV092 PV140-PV180 PV270 PV360

Y 27 - - - - -

A 27 34 39 65 59 59

B 27 34 39 65 59 59

C - 49 39 65 59 59

D - - 39 65 59 59

E - - - - 59 59

G 27 34 39 - - -

H 27 34 39 65 59 59

J 27 34 39 65 59 59

K - 49 39 65 59 59

L - - 39 65 59 59

M - - - - 59 59

2) See page 6 to 17 for reference per each frame size.

63

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Through Drive, Shaft Load Limitations

Important notice

The max. allowable torque of the individual shaft must

not be exceeded. For 2-pump combinations there is no

problembecausePVseriesoffers100%thrutorque.For

3-pump combinations (and more) the limit torque could

be reached or exceeded.

Therefore it is necessary to calculate the torque factor

and compare it with the allowed torque limit factor in the

table.

Required: calculated torque factor

< torque limit factor

To make the necessary calculations easier and more

user friendly it is not required to calculate actual torque

requirements in Nm and compare them with the shaft

limitations. The table on the right shows limit factors that

include material speciﬁcation, safety factors and conver-

sion factors.

Total torque factor of the combination

= sum of individual torque factors of all pumps

Torque factor of any pump

= p x Vg

The total torque factor is represented by the sum of

the individual torque factors of all pumps in the complete

pump combination.

The torque factor of each individual pump is calculated

by multiplying the max. operating pressure p of the pump

(in bar) with the max. displacement Vg of the pump (in

cm³/rev).

Maximum allowed transferable torque FRONT

Shaft

code

Shaft

type

Transferable torque at FRONT shaft end. [Nm]

PV016-028 PV032-046 PV063-092 PV140-180 PV270 PV360

D

SAE - Key 300 650 1850 2150 2150 4750

E

SAE - Spline 320 630 1700 2750 2800 8100

F

SAE - Key 1200

G

SAE - Spline 1700

R

Metric - Key 3750

T

Metric - Spline 8100

K

Metric - Key 280 640 1200 1550 3300 3750

L

Metric - Spline 320 720 1500 3050 5750 8100

Maximum allowed transferable torque REAR

Max. torque transmission cap.

for rear mounted pump

350 520 1100 1550 3150 3250

Pump Shaft Torque limit factor

PV016-028

D 17700

E 17700

K 17700

L 20130

PV032-046

D 32680

E 36380

K 33810

L 40250

PV063-092

D 77280

E 72450

K 67620

L 83720

PV140-180

D 118400

E 158760

F 78750

G

97650

K 113400

L 157500

PV270

D 119000

E 159700

K 170100

L 236250

64

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 360

92

100

105

115

90

Ø250

h8

80

90

Ø250

h8

Ø224

h

8

Ø224

h8

80

90

K

L

R

T

D

E

105

115

Through Drive, Shaft Load Limitations

PV360 shaft options

Max. transferable torque in [Nm] for different shaft options

Metric key Ø70 mm

Max. input torque 3750 Nm

Max. through drive torque 3250 Nm

Metric spline W70x3x22x9g DIN5480

Max. input torque 8100 Nm

Max. through drive torque 3250 Nm

Metric spline W70x3x22x9g DIN5480

Max. input torque 8100 Nm

Max. through drive torque 3250 Nm

Metric key Ø70 mm

Max. input torque 3750 Nm

Max. through drive torque 3250 Nm

SAE key Ø69,85 mm

Max. input torque 4750 Nm

Max. through drive torque 3250 Nm

Metric spline W70x3x22x9g DIN5480

Max. input torque 8100 Nm

Max. through drive torque 3250 Nm

Ø165.1

-0.05

Ø165.1

-0.05

65

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Notes

66

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

Notes

67

Parker Hanniﬁn

Pump and Motor Division

Chemnitz, Germany

Catalogue HY30-3245/UK

Axial Piston Pump

PV 016 to 360

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS

CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from Parker-Hanniﬁn Corporation, its subsidiaries and authorized distributors provide

product or system options for further investigation by users having technical expertise.

The user, through its own analysis and testing, is solely responsible for making the ﬁnal selection of the system and components

and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The

user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning

the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized

distributors.

To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or

speciﬁcations provided by the user, the user is responsible for determining that such data and speciﬁcations are suitable and

sufﬁcient for all applications and reasonably foreseeable uses of the components or systems.

Offer of Sale

Please contact your Parker representation for a detailed ”Offer of Sale”.

WARNING – USER RESPONSIBILITY

Catalogue HY30-3245/UK. 1.5M, 03/2011, ZZ

Your local authorized Parker distributor

Ed. 2010-11-30

Parker Worldwide

Europe, Middle East, Africa

AE – United Arab Emirates,

Dubai

Tel: +971 4 8127100

parker.me@parker.com

AT – Austria, Wiener Neustadt

Tel: +43 (0)2622 23501-0

parker.austria@parker.com

AT – Eastern Europe, Wiener

Neustadt

Tel: +43 (0)2622 23501 900

parker.easteurope@parker.com

AZ – Azerbaijan, Baku

Tel: +994 50 2233 458

parker.azerbaijan@parker.com

BE/LU – Belgium, Nivelles

Tel: +32 (0)67 280 900

parker.belgium@parker.com

BY – Belarus, Minsk

Tel: +375 17 209 9399

parker.belarus@parker.com

CH – Switzerland, Etoy

Tel: +41 (0)21 821 87 00

parker.switzerland@parker.com

CZ – Czech Republic, Klecany

Tel: +420 284 083 111

parker.czechrepublic@parker.com

DE – Germany, Kaarst

Tel: +49 (0)2131 4016 0

parker.germany@parker.com

DK – Denmark, Ballerup

Tel: +45 43 56 04 00

parker.denmark@parker.com

ES – Spain, Madrid

Tel: +34 902 330 001

parker.spain@parker.com

FI – Finland, Vantaa

Tel: +358 (0)20 753 2500

parker.nland@parker.com

FR – France, Contamine s/Arve

Tel: +33 (0)4 50 25 80 25

parker.france@parker.com

GR – Greece, Athens

Tel: +30 210 933 6450

parker.greece@parker.com

HU – Hungary, Budapest

Tel: +36 1 220 4155

parker.hungary@parker.com

IE – Ireland, Dublin

Tel: +353 (0)1 466 6370

parker.ireland@parker.com

IT – Italy, Corsico (MI)

Tel: +39 02 45 19 21

parker.italy@parker.com

KZ – Kazakhstan, Almaty

Tel: +7 7272 505 800

parker.easteurope@parker.com

NL – The Netherlands, Oldenzaal

Tel: +31 (0)541 585 000

parker.nl@parker.com

NO – Norway, Asker

Tel: +47 66 75 34 00

parker.norway@parker.com

PL – Poland, Warsaw

Tel: +48 (0)22 573 24 00

parker.poland@parker.com

PT – Portugal, Leca da Palmeira

Tel: +351 22 999 7360

parker.portugal@parker.com

RO – Romania, Bucharest

Tel: +40 21 252 1382

parker.romania@parker.com

RU – Russia, Moscow

Tel: +7 495 645-2156

parker.russia@parker.com

SE – Sweden, Spånga

Tel: +46 (0)8 59 79 50 00

parker.sweden@parker.com

SK – Slovakia, Banská Bystrica

Tel: +421 484 162 252

parker.slovakia@parker.com

SL – Slovenia, Novo Mesto

Tel: +386 7 337 6650

parker.slovenia@parker.com

TR – Turkey, Istanbul

Tel: +90 216 4997081

parker.turkey@parker.com

UA – Ukraine, Kiev

Tel +380 44 494 2731

parker.ukraine@parker.com

UK – United Kingdom, Warwick

Tel: +44 (0)1926 317 878

parker.uk@parker.com

ZA – South Africa, Kempton Park

Tel: +27 (0)11 961 0700

parker.southafrica@parker.com

North America

CA – Canada, Milton, Ontario

Tel: +1 905 693 3000

US – USA, Cleveland

(industrial)

Tel: +1 216 896 3000

US – USA, Elk Grove Village

(mobile)

Tel: +1 847 258 6200

Asia Paciﬁc

AU – Australia, Castle Hill

Tel: +61 (0)2-9634 7777

CN – China, Shanghai

Tel: +86 21 2899 5000

HK – Hong Kong

Tel: +852 2428 8008

IN – India, Mumbai

Tel: +91 22 6513 7081-85

JP – Japan, Fujisawa

Tel: +81 (0)4 6635 3050

KR – South Korea, Seoul

Tel: +82 2 559 0400

MY – Malaysia, Shah Alam

Tel: +60 3 7849 0800

NZ – New Zealand, Mt Wellington

Tel: +64 9 574 1744

SG – Singapore

Tel: +65 6887 6300

TH – Thailand, Bangkok

Tel: +662 717 8140

TW – Taiwan, Taipei

Tel: +886 2 2298 8987

South America

AR – Argentina, Buenos Aires

Tel: +54 3327 44 4129

BR – Brazil, Sao Jose dos

Campos

Tel: +55 12 4009 3500

CL – Chile, Santiago

Tel: +56 2 623 1216

MX – Mexico, Apodaca

Tel: +52 81 8156 6000

VE – Venezuela, Caracas

Tel: +58 212 238 5422

EMEA Product Information Centre

Free phone: 00 800 27 27 5374

(from AT, BE, CH, CZ, DE, DK, EE, ES, FI, FR, IE, IL,

IS, IT, LU, MT, NL, NO, PL, PT, RU, SE, SK, UK, ZA)

US Product Information Centre

Toll-free number: 1-800-27 27 537

www.parker.com