Catalogue HY17-8249/US

March 2004

Hydraulic

Motor/Pump

Series F11/F12

zp12

Fixed Displacement zp11

Conversion factors

1 kg ............................................................... 2.20 lb

1 N.............................................................. 0.225 lbf

1 Nm........................................................ 0.738 lbf ft

1 bar .............................................................14.5 psi

1 l ....................................................0.264 US gallon

1 cm

.......................................................0.061 cu in

1 mm ........................................................... 0.039 in

°C + 32 .......................................................... 1°F

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Content

Content Page

General information ................................................ 4

F11 cross section ................................................... 4

F12 cross sections ................................................. 5

Specifications ......................................................... 6

Ordering codes

F11-CETOP............................................................ 7

F11-ISO.................................................................. 8

F11-SAE................................................................. 9

F12-ISO................................................................ 10

F12-Cartridge ....................................................... 11

F12-SAE............................................................... 12

Prefered versions F11/F12 ................................... 13

Technical information

Bearing life ........................................................... 14

Bearing life calculation.......................................... 14

Required information ............................................ 14

Noise level ............................................................ 15

Efficiency .............................................................. 15

Selfpriming speed and required inlet pressure ..... 16

Installation dimensions

F11-5 CETOP....................................................... 17

F11-10 CETOP..................................................... 18

F11-14 CETOP..................................................... 19

F11-19 CETOP..................................................... 20

F11-14 ISO........................................................... 21

F11-14 SAE .......................................................... 22

F11-19 SAE .......................................................... 23

F12-30, -40, -60, -80 and -110 ISO ................ 24-25

F12-30, -40, -60, -80 and -110 Cartridge ........ 26-27

F12-30, -40, -60, -80 and -110 4 bolt flange .... 28-29

F12-30, -40, and -60 2 bolt flange ................... 30-31

F11-150 CETOP ................................................... 32

F11-150 SAE........................................................ 33

F11-250 SAE........................................................ 34

Technical information

F11 saw motors .................................................... 35

F11 fan motors ..................................................... 35

F12 integrated flushing valve ................................ 36

F12 accessory valve blocks .................................. 36

Type BT brake valve ............................................. 37

Type SR pressure relief/make-up valve ................ 37

Type SV pressure relief valve ............................... 38

Speed sensor ....................................................... 38

F12 main port suction fittings ............................... 39

Suction fittings ...................................................... 39

Suction fitting kits ................................................. 39

Split-flange kits ..................................................... 39

Installation information ......................................... 40

Direction of rotation .............................................. 40

Hydraulic fluids ..................................................... 40

Operating temperature ......................................... 40

Installation information

Viscosity ............................................................... 41

Filtration ............................................................... 41

Case pressure ...................................................... 41

Case drain connections ........................................ 42

Before start-up ..................................................... 42

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11 cross section

1. Barrel housing

2. Valve plate

3. Cylinder barrel

4. Guide spacer

with O-rings

5. Timing gear

6. Roller bearing

7. Bearing housing

8. Shaft seal

9. Output/input shaft

10. Piston with laminated

piston ring

123456789

F11 and F12 are bent axis, fixed displacement heavy-

duty motor/pump series. They can be used in numer-

ous applications in both open and closed loop circuits.

• Series F11 is available in the following frame sizes

and versions:

- F11-5, -10, -14, 19 and -150 with CETOP mounting

flange and shaft end

- F11-14 with ISO flange and shaft

- F11-14, -19, -150 and -250 with SAE flange and

shaft

• Series F12 conforms to current ISO and SAE

mounting flange and shaft end configurations. A very

compact cartridge version is also available.

• Thanks to the unique spherical piston design, F11/F12

motors can be used at unusually high shaft speeds.

Operating pressures to 480 bar provides for the high

output power capability.

• The 40° angle between shaft and cylinder barrel

allows for a very compact, lightweight motor/pump.

• The laminated piston ring offers important

advantages such as low internal leakage and thermal

shock resistance.

• The pump version has highly engineered valve plates

for increased selfpriming speed and low noise,

available with left and right hand rotation.

• The F11/F12 motors produce very high torque at

start-up as well as at low speeds.

• Our unique timing gear design synchronizes shaft

and cylinder barrel, making the F11/F12 very tolerant

to high 'G' forces and torsional vibrations.

• Heavy duty roller bearings permit substantial external

axial and radial shaft loads.

• The F11's and F12's have a simple and straight-

forward design with very few moving parts, making

them very reliable motors/pumps.

• The unique piston locking, timing gear and bearing

set-up as well as the limited number of parts add up

to a very robust design with long service life and,

above all, proven reliability.

Catalogue HY17-8249/US

General information

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

1231045678

F12 cross sections

1. Barrel housing

2. Valve plate

3. Cylinder barrel

4. Piston with piston ring

F12-30, -40, -60 and -80

(F12-60 shown)

5. Timing gear

6. Tapered roller bearings

7. Bearing housing

8. Shaft seal

9. Output/input shaft

10. Port E (F12-110)

11. Needle bearings (F12-110)

F12-110

Legend:

Catalogue HY17-8249/US

General information

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Frame size F11-5 -10 -14 -19 F12-30 -40 -60 -80 -110 F11-150 -250

Displacement [cm

/rev] 4.9 9.8 14.3 19.0 30.0 40.0 59.8 80.4 110.1 150 242

[cu in/rev] 0.30 0.60 0.87 1.16 1.83 2.44 3.65 4.91 6.72 9.15 14.8

Operating pressure

max intermittent

[bar] 420 420 480 480 420 420

[psi] 6 000 6 000 7 000 7 000 6 000 6 000

max continuous [bar] 350 350 420 420 350 350

[psi] 5 000 5 000 6000 6000 5 000 5 000

Motor operating speed [rpm]

max intermittent

12 000 11 000 10 000 9 000 7 100 6 400 5 600 5 200 4 700 3 000 2 700

max continuous 10 800 9 900 9 000 8 100 5 600 5 000 4 300 4 000 3 600 2 600 2 400

min continuous 50 50

Max pump selfpriming speed

L or R function; max [rpm] 4 600 4 200 3 900 3 500 3150 2870 2500 2300 2290 1 700 1 500

Motor input flow

max intermittent

[l/min] 58 108 143 171 213 256 335 418 517 450 650

[gpm] 15.3 28.5 37.8 45.2 56.3 67.6 88.5 110.4 136.6 119.0 172.8

max continuous [l/min] 52 97 128 153 168 200 257 322 396 390 580

[gpm] 13.7 25.6 33.8 40.4 44.4 52.8 67.9 85.1 104.6 103.0 153.6

Main circuit temp.

, max [°C] 80 80

[°F] 175 175

min [°C] -35 -35 -30 -35 -35 -35 -35 -35

[°F] -31 -31 -22 -31 -31 -31 -31 -31

Mass moment of inertia

(x10

-3

) [kg m

]

0.16 0.39 0.42 1.1 1.7 2.9 5 8.4 11.2 40 46

(x10

-2

)

[lbft

] 0.38 0.92 1.00 2.61 4.03 6.88 11.86 19.93 26.58 94.92 109.16

Weight [kg] 5 7.5 8.3 11 12 16.5 21 26 36 70 77

[lb] 11 16.5 18.8 24 26 36 46 57 79 154 170

1) Intermittent: max 6 seconds in any one minute.

2) Selfpriming speed valid at sea level.

3) See also installation information, operating temperature.

Catalogue HY17-8249/US

Specifications

Torque (M)

M = [Nm]

Basic formulas for hydraulic motors

Flow (q)

q = [l/min]

Power (P)

P = [kW]

D x n

1000 x η

D x ∆p x η

q x ∆p x η

600

D - displacement [cm

/rev]

n - shaft speed [rpm]

- volumetric efficiency

∆p - differential pressure [bar]

(between inlet and outlet)

- mechanical efficiency

- overall efficiency

(η

x η

)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-CETOP

x: Available (x): Optional – : Not available

1) Internal drain

2) BSP threads

3) NBR - Nitrile rubber

4) FPM - Fluor rubber

Catalogue HY17-8249/US

Ordering codes

Frame size

Code Displacem.

(cm

/rev)

5 4.9

10 9.8

14 14.3

19 19.0

150 150.0

Frame size 5 10 14 19 150

Code Main ports

B BSP threads x x x x -

R With anti-cavitation

valve; clockwise rot’n

-xxx-

L With anti-cavitation

valve; counter clockw.

-xxx-

U SAE, UN threads (x) (x) - (x) -

F SAE 6000 psi flange - - - - x

Frame size 5 10 14 19 150

Code Function

M Motor x x - x x

H Motor, high pressure x x x x x

Q Motor, silent (x) (x) - (x) (x)

J Motor, clockwise rot'n

(x) (x) - (x) (x)

G Motor, counter clockw.

(x) (x) - (x) (x)

R Pump, clockwise rot'n x x x x x

L Pump, counter clockw. x x x x x

Frame size 5 10 14 19 150

Code Mounting flange

C CETOP flange x x x x x

W Saw motor flange - x x x -

Frame size 5 10 14 19 150

Code Shaft seal

N NBR

, low pressure x x - x x

H NBR

, high pressure x x - x x

E FPM

, low pressure,

high temperature x x x x x

V FPM

, high pressure,

high temperature - x x x -

Frame size 5 10 14 19 150

Code Shaft

K Metric key x x x x x

D Spline, DIN 5480 (x) (x) (x) (x) (x)

Version number

(assigned for special

versions)

F11 — — ——— — —

Frame

size

Function

Main

ports

Mounting

flange

Shaft

seal

Shaft

Version

number

Option

page 36

Option

page 38

Frame size 5 10 14 19 150

Code Option

S With speed sensor - - x x -

P Prepared for speed

sensor - - x x -

Option

None

Pump

Motor

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-ISO

x: Available (x): Optional – : Not available

1) FPM - Fluor rubber

Catalogue HY17-8249/US

Ordering codes

Frame size

Code Displacem.

(cm

/rev)

14 14.3

Frame size 14

Code Main ports

F SAE 6000 psi flange x

Frame size 14

Code Function

H Motor, high pressure x

R Pump, clockwise rot'n x

L Pump, counter clockw. x

Frame size 14

Code Mounting flange

I ISO flange x

Frame size 14

Code Shaft seal

E FPM

, low pressure,

high temperature x

V FPM

, high pressure,

high temperature x

Frame size 14

Code Shaft

K Metric key x

D Spline, DIN 5480 (x)

Version number

(assigned for special

versions)

F11 — — ——— — —

Frame

size

Function

Main

ports

Mounting

flange

Shaft

seal

Shaft

Version

number

Option

page 36

Option

page 38

Frame size 14

Code Option

S With speed sensor x

P Prepared for speed

sensor x

Option

None

Pump

Motor

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Ordering codes

Pump

Motor

F11-SAE

x: Available (x): Optional – : Not available

1) Internal drain

2) Metric thread

3) BSP threads

4) NBR - Nitrile rubber

5) FPM - Fluor rubber

Frame size

Code Displacem.

(cm

/rev)

14 14.3

19 19.0

150 150.0

250 242.0

Frame size 14 19 150 250

Code Main ports

U SAE, UN threads x x - -

B BSP threads - (x) - -

F SAE 6000 psi flange

--xx

R With anti-cavitation

valve; clockwise rot’n

xx- -

L With anti-cavitation

valve; counter clockw.

xx- -

Frame size 14 19 150 250

Code Function

M Motor - x x -

H Motor, high pressure x x x -

Q Motor, silent - (x) (x) x

J Motor, clockwise rot'n

- (x) (x) -

G Motor, counter clockw.

- (x) (x) -

R Pump clockwise rot'n x x x x

L Pump counter clockw. x x x x

Frame size 14 19 150 250

Code Mounting flange

S SAE flange x x x x

Frame size 14 19 150 250

Code Shaft seal

N NBR

, low pressure - x x x

H NBR

, high pressure - x x x

E FPM

, low pressure,

high temperature x x x x

V FPM

, high pressure,

high temperature x x - -

Frame size 14 19 150 250

Code Shaft

T SAE key x x x -

S SAE spline (x) (x) (x) (x)

K Metric key - - - x

F SAE spline - - - (x)

Version number

(assigned for special

versions)

F11 — — ——— — —

Frame

size

Function

Main

ports

Mounting

flange

Shaft

seal

Shaft

Version

number

Option

page 36

Option

page 38

Frame size 14 19 150 250

Code Option

S With speed sensor x x - -

P Prepared for speed

sensor x x - -

Option

None

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Ordering codes

F12-ISO

Frame size

Code Displacem.

(cm

/rev)

30 30.0

40 40.0

60 59.8

80 80.4

110 110.1

Frame size 30 40 60 80 110

Code Option

S With speed sensor x x x x x

P Prepared for speed

sensor x x x x x

Frame size 30 40 60 80 110

Code Main ports

F ISO flange x x x x x

Frame size 30 40 60 80 110

Code Shaft seal

H NBR

, high pressure x x x x x

N NBR

, low pressure x x x x x

V FPM

, high temperature, x x x x x

high pressure

Frame size 30 40 60 80 110

Code Shaft

D DIN spline Standard x x x x x

Z Optional (x) (x) - (x) -

K Metric key Standard x x x x x

P Optional (x) - - - -

Frame size 30 40 60 80 110

Code Option

L01 Integr. flushing valve x x x x -

Frame size 30 40 60 80 110

Code Mounting flange

I ISO flange x x x x x

Frame size 30 40 60 80 110

Code Function

M Motor x x x x x

Pump:

L counter clockw. x x x x x

R clockwise x x x x x

x: Available (x) : Optional – : Not available

1) NBR - Nitrile rubber

2) FPM - Fluor rubber

3) F12-110: Accessory valve block (page 36)

Version number

(assigned for

special versions)

F12 — — ——— — —

Frame

size

Function

Main

ports

Mounting

flange

Shaft

seal

Shaft

Version

number

Option

page 36

Option

page 38

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F12-Cartridge

Catalogue HY17-8249/US

Ordering codes

F12 — — ——— — —

Frame

size

Function

Main

ports

Mounting

flange

Shaft

seal

Shaft Version

number

Option

page 36

Option

page 38

Frame size

Code Displacem.

(cm

/rev)

30 30.0

40 40.0

60 59.8

80 80.4

110 110.1

Frame size 30 40 60 80 110

Code Function

M Motor x x x x x

Frame size 30 40 60 80 110

Code Main ports

F ISO flange x x x x x

Frame size 30 40 60 80 110

Code Mounting flange

C Cartridge x x x x x

Frame size 30 40 60 80 110

Code Shaft seal

H NBR

, high pressure x x x x x

N NBR

, low pressure x x x x x

V FPM

high temperature, x x x x x

high pressure)

Frame size 30 40 60 80 110

Code Shaft

C DIN spline Standard x x x x x

K Metric key Standard x - x x -

X " " Optional - (x) - - -

Frame size 30 40 60 80 110

Code Option

L01 Integr. flushing valve x x x x -

Frame size 30 40 60 80 110

Code Option

S With speed sensor x x x x x

P Prepared for speed

sensor x x x x x

x: Available (x) : Optional – : Not available

1) NBR - Nitrile rubber

2) FPM - Fluor rubber

3) F12-110: Accessory valve block (page 36)

Version number

(assigned for

special versions)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

x: Available (x) : Optional – : Not available

1) NBR - Nitrile rubber

2) FPM - Fluor rubber

3) F12-110: Accessory valve block (page 36)

Catalogue HY17-8249/US

Ordering codes

F12 — — ——— — —

F12-SAE

Frame size

Code Displacem.

(cm

/rev)

30 30.0

40 40.0

60 59.8

80 80.4

110 110.1

Frame

size

Function Main

ports

Mounting

flange

Shaft

seal

Shaft

Version

number

Option

page 36

Option

page 38

Frame size 30 40 60 80 110

Code Option

S With speed sensor x x x x x

P Prepared for speed

sensor x x x x x

Frame size 30 40 60 80 110

Code Main ports

S SAE flange x x x x x

U SAE, UN threads (x) (x) (x) - (x)

Frame size 30 40 60 80 110

Code Shaft seal

H NBR

, high pressure x x x x x

N NBR

, low pressure x x x x x

V FPM

, high temperature, x x x x x

high pressure

Frame size 30 40 60 80 110

Code Shaft

S SAE spline Standard xxxxx

U " " Optional - - - (x) -

T SAE key Standard xxxxx

Frame size 30 40 60 80 110

Code Option

L01 Integr. flushing valve x x x x -

Frame size 30 40 60 80 110

Code Mounting flange

S SAE 4 bolt x x x x x

T SAE 2 bolt x x x - -

Frame size 30 40 60 80 110

Code Function

M Motor x x x x x

Pump:

L counter clockw. x x x x x

R clockwise x x x x x

Version number

(assigned for

special versions)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Prefered versions F11/F12 catalogue

F11

Ordering Codes Part number

F11-005-MB-CN-K 3703665

F11-005-MB-CH-K 3707249

F11-005-HU-CH-K 3707308

F11-010-MB-CN-K 3703603

F11-010-MB-CH-K 3706030

F11-010-HU-CH-K 3707310

F11-014-HB-CE-K 3783201

F11-014-HB-CV-K 3782830

F11-019-MB-CN-K 3703516

F11-019-MB-CH-K 3707893

F11-150-MF-CN-K 3703468

F11-150-MF-CH-K 3707008

F11-150-HF-SH-S 3707325

F11-250-QF-SH-F 3706440

F11-250-QF-SH-K 3795858

F12

Ordering Codes Part number

F12-30-MF-IH-D 3799843

F12-30-MF-IH-K 3799844

F12-30-MS-SH-S 3799851

F12-30-MS-TH-S 3799616

F12-40-MF-IH-D 3799525

F12-40-MF-IH-K 3799526

F12-40-MS-SH-S 3799532

F12-40-MS-SH-T 3799533

F12-40-MS-TH-S 3799617

F12-60-MF-IH-D 3799988

F12-60-MF-IH-K 3799989

F12-60-MS-SH-S 3799998

F12-60-MS-TH-S 3799618

F12-80-MF-IH-D 3780767

F12-80-MF-IH-K 3780772

F12-80-MS-SH-S 3780783

F12-110-MF-IH-D 3781530

F12-110-MF-IH-K 3781534

F12-110-MS-SH-S 3781542

Catalogue HY17-8249/US

Ordering codes

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Life expectancy

(logarithmic scale)

Other

causes

Bearing

fatigue

Rotating group

fatigue and wear

System

pressure

Hydraulic unit life versus system pressure.

Bearing life

General information

Bearing life can be calculated for that part of the load/

life curve (shown below) that is designated 'Bearing

fatigue'. 'Rotating group fatigue and wear' and 'Other'

caused by material fatigue, fluid contamination, etc.

should also be taken into consideration when estimat-

ing the service life of a motor/pump in a specific appli-

cation.

Bearing life calculations are mainly used when compar-

ing different frame sizes. Bearing life, designated B

(or L

), is dependent of system pressure, operating

speed, external shaft loads, fluid viscosity in the case,

and fluid contamination level.

The B

value means that 90% of the bearings survive,

at a minimum, the number of hours calculated. Statisti-

cally, 50% of the bearings will survive at least five

times the B

life.

Bearing life calculation

An application is usually governed by a certain duty or

work cycle where pressure and speed vary with time

during the cycle.

In addition, bearing life depends on external shaft

forces, fluid viscosity in the case and fluid conta-

mination.

Parker Hannifin (Mobile Controls Division) has a

computer program for calculating bearing life and will

assist in determining F11 or F12 motor/pump life in a

specific application.

Required information

When requesting a bearing life calculation from Parker

Hannifin (Mobile Controls Division), the following

information (where applicable) should be provided:

- A short presentation of the application

- F11 or F12 size and version

- Duty cycle (pressure and speed versus time

at given displacements)

- Low system pressure

- Case fluid viscosity

- Life probability (B

, B

, etc.)

- Operating mode (pump or motor)

- Direction of rotation (L or R)

- External shaft loads

- Fixed or rotating radial load

- Distance between flange and radial load

- Angle of attack (α) as defined below

The direction (a) of the radial load is positive in the

direction of rotation as shown.

To obtain maximum bearing life, the radial load should,

in most cases, be located approximately at 170°

(motor; R.H. rot'n) or 190° (pump; R.H rot'n).

Catalogue HY17-8249/US

Technical information

F F

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Noise level

Series F11/F12 feature low noise levels from low to

high speeds and pressures.

As an example, the diagram to the right shows the

noise level of an F12-30.

The noise level is measured in a semi-anechoic room,

1 m behind the unit.

The noise level for a particular motor/pump may vary

±2 dB(A) compared to what is shown in the diagram.

NOTE: Noise information for F11/F12 frame

sizes are available from Parker Hannifin.

Efficiency

Because of its high overall efficiency, driving a motor/

pump from series F11/F12 requires less fuel or electric

power. Also, it allows the use of a small reservoir and

heat exchanger, which in turn reduce cost, weight, and

installation size.

The diagrams to the right shows volumetric and

mechanical efficiencies of an F12-30.

Contact Parker Hannifin for efficiency information on a

particular F11/F12 frame size that is being considered.

Catalogue HY17-8249/US

Technical information

Volumetric efficiency.

Mechanical efficiency.

100%

90%

80%

0 1000 2000 3000 4000 Speed

[rpm]

100%

90%

80%

0 1000 2000 3000 4000 Speed

[rpm]

F12-30

(motor)

F12-30

(motor)

3000 psi

6000 psi

3000 psi

Noise level

[dB(A)]

0 1000 2000 3000 4000 5000 Pressure

[psi]

5000 rpm

3500 rpm

2000 rpm

F12-30

(M, L or R function)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

1000 2000 3000 4000 Speed [rpm]

F12-110 -80 -60 -40 -30

1000 2000 3000 4000 Speed [rpm]

F12-110 -80 -60 -40 -30

F12-L or -R

F12-M

Inlet press.

[psi]

5 in. Hg vacuum

Inlet press.

[psi]

5 in. Hg vacuum

Inlet

pressure

gauge

Function L or RM H

F11-5 4600 3800 3200

F11-10 4200 3100 2700

F11-14 3900 - 3200

F11-19 3500 2400 2100

F11-150 1700 1300 1100

F11-250 1500 950 -

Selfpriming speed and required inlet

pressure

Series F11

In pump applications, the F11 with function L (counter

clockwise rotation) or R (clockwise rotation) is normally

used. The L and R (pump) provide the highest self-

priming speeds (see table) as well as the lowest noise

level. The M (motor) function can also be used as a

pump, in either direction, but at a lower selfpriming

speed.

Operating above the selfpriming speed (refer to

Diagram 1) requires increased inlet pressure.

As an example, at least 1.0 bar is needed when operat-

ing the F11-19-M as a pump at 3500 rpm. An F11 with

H function, used as a motor (e.g. in a hydrostatic

transmission), may sometimes operate as a pump at

speeds above the selfpriming speed; this requires

additional inlet pressure.

Insufficient inlet pressure can cause pump cavitation

resulting in greatly increased pump noise and deterio-

rating performance.

Series F12

When operating the F12 as a pump (with L or R valve

plate) above the selfpriming speed, the inlet must be

pressurized. Increased noise and deteriorating per-

formance may otherwise be experienced.

Diagrams 2 and 3 show required pump inlet pressure

vs. shaft speed.

The F12 motor (type M valve plate) sometimes oper-

ates as a pump e.g. when used in a propel transmis-

sion and the vehicle is going downhill.

Minimum required inlet pressure versus shaft speed is

shown in the diagrams.

Diagram 2.

Min. required pump (F12-L or -R) inlet press.

Diagram 3. Min. required motor (F12-M) inlet pressure.

Diagram 1. Min required inlet pressure (F11-19).

NOTE:

Diagrams 1, 2 and 3 are valid

at sea level.

Catalogue HY17-8249/US

Technical information

L, R

1000 2000 3000 4000 Speed [rpm]

Inlet pressure

[psi]

F11-19

5 in. Hg vacuum

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-5

(CETOP versions)

Catalogue HY17-8249/US

Installation dimensions

3.31 max

1.50

Main port A

BSP ½"

Main port B

BSP ½"

Drain port C

BSP ¼"

2.56

0.20

1.87

3.48

2.13

1.57

1.18

0.20

40˚

0.35

0.51

5.28 max

Ø0.7090

0.7085

Ø3.1496

3.1478

Ø0.80 min

Approx.

center of

gravity

3.78 max

2.09

4.47

0.31

0.47

min

0.98

0.35

0.79

M6*

0.81

Ø0.43 (x2)

Ø5.00

max

3.94

Drain port D

BSP ¼"

Flange C

Key shaft K

Key 6x6

R 0.03

R 0.02

W18x1,25x13x9g

Type D spline shaft (DIN 5480)

Mounting flange C

* Metric thread

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-10

(CETOP versions)

Catalogue HY17-8249/US

Installation dimensions

3.70 max

1.81

Main port A

BSP ¾"

Main port B

BSP ¾"

Drain port C

BSP

/8"

3.11

0.43

2.09

3.98

2.48

1.97

1.38

0.28

40˚

0.35

0.55

6.14 max

Ø0.7878

0.7872

Ø3.9370

3.9349

Ø0.91 min

Approx.

center of

gravity

4.57 max

2.24

5.24

0.31

0.47

min

1.18

0.35

0.87

M6*

0.89

Ø0.51 (x2)

Ø5.98

max

4.92

Drain port D

BSP ¼"

Flange C

Key shaft K

Key 6x6

R 0.03

R 0.02

W20x1.25x14x9g

Spline shaft D (DIN 5480)

Mounting flange C

* Metric thread

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-14

(CETOP versions)

Catalogue HY17-8249/US

Installation dimensions

B A

25˚

3.94

5.87

6.18

max

0.37

1.65 1.38

0.55

0.14

4.02

1.772.83

2.09

1.26

2.32

R 0.03

5.51

Ø0.51 (x2)

4.49

5.91

39˚ (x4)

0.31

Ø1.06

Ø0.9846

0.9841

4.02

1.81

1.18

0.31

1.10

Ø0.9744

M8x0.63

Ø3.9370

3.9349

R 0.02

1.02

Anticavitation valve

(left or right hand optional;

right hand shown)

Main port A

(BSP 3/4”-A)

W 25x1.25x18x9g

Type D spline

shaft (DIN 5480)

Drain port C

(BSP 3/8”-A)

Speed sensor

(optional)

Flange C

Drain port D

(BSP 3/8”-A)

Type K key shaft

CCW CW

Type C mounting flange

Key 8x7x35

Main port B

(BSP 3/4”-A)

5.24

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-19

(CETOP version)

3.46

0.43

2.48

4.49 max

2.13

Drain port D

BSP

/8"

Main port A

BSP ¾"

Main port B

BSP ¾"

Drain port C

BSP

/8"

Flange C

Key shaft K

Key 8x7x35

R 0.05

max

R 0.04

max

Ø1.11 min

Ø0.9846

0.9841

Ø4.4094

4.4073

2.28

0.98

1.65

6.50 max

1.14

0.98

1.10

0.91

5.43

3.94

0.63

0.39

45˚

4.96

Ø6.69

max

Ø0.55 (x2)

3.42

5.51

Mounting flange C

Approx.

center of

gravity

0.63

min

M8*

1.10

W25x1.25x18x9g

Spline shaft D (DIN 5480)

* Metric thread

Catalogue HY17-8249/US

Installation dimensions

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-14

(ISO versions)

Catalogue HY17-8249/US

Installation dimensions

B A

3.98 Main ports M26

(metric thread;

depth 0.47;

ISO 9974-1)

Drain port M26

(metric thread;

depth 0.47;

ISO 9974-1)

Drain port M26

(metric thread;

depth 0.47;

ISO 9974-1)

1.81

4.84

1.18

1.10

Ø0.974

W25x1.235x18x9g)

Type D spline shaft (DIN 5480)

R 0.02 max

0.26

0.73

0.47

M8 (metric thread)

0.63 deep

Ø3.1496/3.1478

0.31

Ø1.06

Ø0.9846/0.9841

1.10

3.54

5.47

5.79

(max)

0.83

1.65

1.38

Type K key shaft

Flange I

(ISO 3019/2)

0.14

2.866

4.02

1.77 Speed sensor

(optional)

2.09

0.41 (x4)Ø0.35 (x4)

Ø0.35 (x4)

3.74

CCW CW

Type I mounting flange (ISO 3019/2)

Key 8x7x35

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-14

(SAE versions)

Catalogue HY17-8249/US

Installation dimensions

Ø0.94 (x2)

0.250

Ø1.06

Ø1.000/0.998

4.02

0.95

1.30

0.31

1.50

1.25

5.94

0.67

(x2)

6.21

(max)

5.75

29˚ (x4)

4.02

1.77 Speed sensor

(optional)

2.09

25˚

Ø0.57 (x2)

4.72

6.85 (max)

R 10.24 (x2)

CCW CW

R 0.55 (x4)

(0.31)

3.98

1.81

5.24

1.18

Ø3.15

1.11

"-24 UNF-2B

(0.63 deep)

R 0.02

0.37

Ø4.000/3.998

Main ports 1

"-12 UN,

O-ring boss; SAE J514d

Drain port

" UNF;

O-ring boss; SAE J514d

Type S spline shaft

13 T,

(SAE J498b; class 1,

30 involute spline,

flat root, side fit)

Drain port

" UNF,

O-ring boss; SAE J514d

Type T key shaft

Key

8x7x35

Type S mounting flange SAE 'B' ( SAE J744c)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-19

(SAE version)

Catalogue HY17-8249/US

Installation dimensions

3.46

0.43

2.48

Drain port D

/16"-18

Flange S

Key shaft T

SAE 'B-B'

(SAE J744c)

Key

"x1

R 0.04

R 0.03

Ø1.11 min

Ø1.000

0.998

2.91

0.31

1.50

7.13 max

0.31

1.30

4.61

0.67

Spline shaft S (SAE J498b)

Approx.

center of

gravity

SAE 'B' (13T, 16/32 DP;

class 1, flat root, side fit)

2.13

Main port A

11/16"-12*

Main port B

11/16"-12*

Drain port C

/16"-18

Ø4.000

3.998

Ø6.93

max

1.14

0.38

6.10

30˚

Ø0.57 (x2)

Mounting flange S

SAE 'B' (SAE J744c)

0.63

min

/16"/24**

1.11

R 0.55

1.02

5.75

4.84

4.49 max

* O/ring boss (SAE J514d)

** UNC thread

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F12-30, -40, -60, -80 and -110

(ISO versions)

Catalogue HY17-8249/US

Installation dimensions

See

table

D3 (thread)

Ø E3

Type I

flange

Ø E2

Ø F2

(±0.02)

Port C

Port D Port A Port B

Ø D1 (x4)

Type I mounting flange

(ISO 3019/2)

Type D (Z)

spline shaft

Type K (P)

key shaft

Port E (third drain port)

F12-110 barrel housing

(ISO/cartridge version)

NOTE:

Type Z has

no thread

Flushing

valve

(optional)

Speed

sensor

(optional)

1) Inspection/

drain port

Shown: F12-80

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Installation dimensions

Dim. F12-30 F12-40 F12-60 F12-80 F12-110

A1 3.48 4.46 4.46 5.01 5.57

B1 4.65 5.75 5.75 6.22 7.09

C1 4.65 5.59 5.67 6.10 7.09

D1 0.43 0.53 0.53 0.53 0.71

A2 3.94 4.33 4.92 5.32 5.71

B2 2.32 2.56 2.76 3.05 3.35

C2 0.98 1.02 0.87 1.26 1.50

D2 0.32 0.32 0.39 0.47 0.55

E2 1.30 1.65 1.65 2.05 2.26

F2 3.9370/ 4.9213/ 4.9213/ 5.5118/ 6.2992/

3.9349 4.9188 4.9188 5.5093 6.2967

G2 6.77 6.81 7.48 8.50 9.09

H2 1.00 1.28 1.28 1.28 1.59

1.97 2.36 2.36 2.76 3.23

1.97 - - - -

K2 2.16 2.05 2.13 2.76 2.61

L2 1.58 1.97 1.97 2.21 2.76

M2 0.20 0.20 0.20 0.28 0.24

N2 5.37 5.39 6.06 6.79 7.05

P2 0.32 0.32 0.32 0.32 0.32

Q2 1.10 1.10 1.30 1.42 1.61

1.38 1.38 1.61 1.77 1.97

1.69 1.38 - 1.61 -

S2*

M12 M12 M12 M16 M16

x24 x24 x28 x36 x36

A3 4.80 5.28 5.67 6.10 6.69

B3 2.60 2.60 2.60 2.95 3.29

C3 0.937 0.937 0.937 1.094 1.250

D3* M12 M12 M12 M16 M16

E3 1.1817/ 1.1817/ 1.3787/ 1.5755/ 1.7724/

1.1812 1.1812 1.3780 1.5749 1.7717

F3 1.30 1.30 1.50 1.69 1.91

G3 5.37 5.39 6.06 6.79 7.05

H3 0.93 1.20 1.20 1.20 1.52

J3 0.95 0.95 1.10 1.42 1.42

K3 2.000 2.000 2.000 2.250 2.626

L3 0.71 0.79 0.79 0.79 0.87

S3 0.63 0.63 0.63 1.02 -

T3----2.68

* Metric thread

1) Key shaft type K 3) Spline shaft type D

2) " " " P 4) " " " Z.

Ports F12-30 F12-40 F12-60 F12-80 F12-110

A, B

"1"1

size

Screw M10 M10 M10 M12 M14

thread

(0.79) (0.79) (0.79) (0.79) (1.02)

C, D M22 M22 M22 M22 M22

thread

x1.5 x1.5 x1.5 x1.5 x1.5

E - - - - M22

thread

x1.5

A, B: ISO 6162 1) Metric thread (depth in inches)

2) Metric thread x pitch in mm.

Spline shaft (DIN 5480; in mm)

= Max 5 100 psi (350 bar) operating pressure.

Metric key shaft (in mm)

Type K (standard) Type P (optional)

F12-30 30 dia. 25 dia.

-40 30 dia. -

-60 35 dia. -

-80 40 dia. -

-110 45 dia. -

Type D (standard) Type Z (optional)

F12-30 W30x2x14x9g W25x1.25x18x9g

-40 W32x2x14x9g W30x2x14x9g

-60 W35x2x16x9g W32x2x14x9g

-80 W40x2x18x9g W35x2x16x9g

-110 W45x2x21x9g -

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F12-30, -40, -60, -80 and -110

(Cartridge versions)

Catalogue HY17-8249/US

Installation dimensions

Ø V5

Ø F5

See table

Type C

spline

shaft

(±0.2)

Ø M6

Ø N6

Ø P6

O-ring

(included)

Port DPort BPort A

Port C

Ø D4

(x2)

40 (-30, -40, -60, -110)

43 (-80)

Flushing

valve

(optional)

Speed

sensor

(optional)

Type C mounting flange

1) Inspection/

drain port

Port E (third drain port)

F12-110 barrel housing

(ISO/cartridge version)

Shown: F12-80

Ø E5

Type K (X) key shaft

XX˚

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Installation dimensions

O-ring dimensions (in mm)

F12-30 127x4

-40 150x4

-60 150x4

-80 180x4

-110 190x4

Ports F12-30 F12-40 F12-60 F12-80 F12-110

A, B

"1"1

size

Screw M10 M10 M10 M12 M14

thread

(0.79) (0.79) (0.79) (0.87) (1.02)

C M14 M14 M14 M14 M14

thread

x1.5 x1.5 x1.5 x1.5 x1.5

D, E M18 M18 M22 M22 M22

thread

x1.5 x1.5 x1.5 x1.5 x1.5

A, B: ISO 6162 3) Metric thread (depth in inches)

4) Metric thread x pitch in mm.

Dim. F12-30 F12-40 F12-60 F12-80 F12-110

A4 6.30 7.87 7.87 8.82 9.84

B4 5.51 6.46 6.46 7.72 8.11

C4 7.40 9.25 9.25 10.24 11.26

D4 0.55 0.71 0.71 0.87 0.87

E4 3.03 3.74 3.74 4.33 4.57

A5 3.94 4.33 4.92 5.31 5.71

B5 2.32 2.56 2.76 3.05 3.35

C5 0.98 1.02 0.87 1.26 1.50

D5 0.31

0.39 0.47 0.55

E5 1.1817/

1.3787/ 1.5755/ 1.7724/

1.1812 1.3780 1.5749 1.7717

F5 5.3150/ 6.2992/ 6.2992/ 7.4803/ 7.8740/

5.3125 6.2967 6.2967 7.4775 7.8712

G5 5.00 5.24 5.75 6.18 6.89

H5 3.50 3.63 3.63 4.35 4.83

J5 1.97 2.36 2.36 2.76 -

K5 0.55 0.63 0.59 0.59 0.59

L5 1.57 1.97 1.97 2.20 -

M5 0.20 0.20 0.20 0.28 -

N5 3.58 3.82 4.33 4.49 4.84

P5 0.87 1.18 1.22 1.57 1.57

Q5 1.10 1.10 1.10 1.46 1.46

R5 1.38 1.38 1.38 1.77 1.77

S5 2.78 2.83 2.99 3.58 3.77

T5 0.59 0.59 0.59 0.59 0.59

V5 1.30 1.38 1.38 1.77 1.77

A6 4.80 5.28 5.67 6.10 6.69

B6 2.60 2.60 2.60 2.95 3.27

C6 0.937 0.937 0.937 1.094 1.250

G6 3.60 3.82 4.33 4.49 4.84

H6 2.74 2.80 2.91 3.52 3.69

K6 2.000 2.000 2.000 2.250 2.626

L6 0.63 0.71 0.71 0.79 0.79

M6 3.62 4.53 4.53 5.12 5.51

N6 4.33 5.00 5.31 6.06 6.30

P6 5.047 6.031 6.031 7.213 7.606

Q6 0.20 0.20 0.20 0.20 0.20

R6 0.20 0.20 0.20 0.20 0.20

T6----2.68

1) Key shaft type K: D5 - 0.31; E5 - 1.1817/1.1812

2) Key shaft type X: D5 - 0.39; E5 - 1.3787/1.3780

Spline shaft (DIN 5480; in mm)

Type C (standard)

F12-30 W30x2x14x9g

-40 W30x2x14x9g

-60 W30x2x14x9g

-80 W40x2x18x9g

-110 W40x2x18x9g

Metric key shaft (in mm)

Type K (std) Type X (opt.)

F12-30 30 dia. –

-40 - 35 dia.

-60 35 dia. –

-80 40 dia. –

-110 – –

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F12-30, -40, -60, -80 and -110

(SAE versions with 4 bolt flange)

Catalogue HY17-8249/US

Installation dimensions

Ø D7 (x4)

Type S (SAE 4 bolt) mounting flange

Port E (third drain port)

F12-110 barrel housing

(SAE version)

Type S

flange

Ø E8

Ø F8

Port C

Port D

Type T

key shaft

Flushing

valve

(optional)

Speed

sensor

(optional)

1) Inspection/

drain port

See

table

D9 (thread)

Ø E9

Port A Port B

Type S (U)

spline shaft

Shown: F12-80 with 4 bolt flange

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Installation dimensions

Dim. F12-30 F12-40 F12-60 F12-80 F12-110

A7 3.54 4.51 4.51 4.51 6.36

B7 4.65 5.83 5.83 6.10 8.03

C7 4.65 5.67 5.67 6.10 7.87

D7 0.55 0.55 0.55 0.55 0.83

A8 3.94 4.33 4.92 5.31 5.71

B8 2.32 2.56 2.76 3.05 3.35

C8 0.98 1.02 0.87 1.26 1.50

D8 0.25 0.31 0.31 0.38 0.44

E8 1.30 1.65 1.65 2.05 2.26

F8 4.000/ 5.000/ 5.000/ 5.000/ 6.000/

3.998 4.998 4.998 4.998 5.998

G8 7.46 7.76 8.43 9.45 10.39

H8 0.31 0.31 0.31 0.31 0.31

J8 1.50 1.89 1.89 2.13 2.64

K8 2.83 2.99 3.11 3.74 3.90

L8 1.25 1.50 1.50 1.75 2.13

M8 0.10 0.16 0.16 0.16 0.29

N8 6.04 6.34 7.02 7.76 8.35

0.91 0.91 0.91 0.98 1.34

---0.91-

1.30 1.89 1.89 2.13 2.63

---1.88-

A9 4.80 5.28 5.67 6.10 6.69

B9 2.60 2.60 2.60 2.95 3.27

C9 0.937 0.937 0.937 1.094 1.250

D9*

"-24

"-20

"-18

E9 1.000/ 1.250/ 1.250/ 1.500/ 1.750/

0.998 1.248 1.248 1.498 1.748

F9 1.11 1.39 1.39 1.67 1.94

G9 6.06 6.34 7.02 7.76 8.35

H9 0.38 0.50 0.50 0.50 0.50

J9 0.63 0.75 0.75 1.02 1.26

K9 2.000 2.000 2.000 2.250 2.626

L9 0.71 0.79 0.79 0.79 0.87

T9----2.68

* UNF-2B thread

1) Spline shaft type S

2) " " " U

Main ports A and B, type U (optional)

F12-110 1

" - 12 UN

O-ring ports according to SAE J514d

Ports F12-30 F12-40 F12-60 F12-80 F12-110

A, B

"1"1

size

Screw

"-16

"-14

"-13

thread

(0.87) (0.79) (0.87) (1.06) (0.98)

"-14

"-14 1

"-12

thread

"-16

"-14

"-14 1

"-12

thread

E- - - -1

"-12

thread

A, B: ISO 6162; C, D, E: O-ring boss (SAE J514)

3) UN thread (depth in inches)

Key shaft (SAE J744)

T (standard) X (optional)

F12-30 SAE 'B-B' -

(1"/ 25.4 mm)

-40 SAE 'C' -

"/ 31.75 mm)

-60 SAE 'C' -

"/ 31.75 mm)

-80 SAE 'C-C' SAE ’D’

"/ 38.1 mm) (1

"/ 44.45 mm)

-110 SAE 'D' -

"/ 44.45 mm)

Mounting flange (SAE J744)

S (standard) X (optional)

F12-30 SAE 'B', 4 bolt -

-40 SAE 'C', " -

-60 SAE 'C', " -

-80 SAE 'C', " SAE ’D’, 4 bolt

-110 SAE 'D', " -

Spline shaft (SAE J498b, class 1, flat root, side fit)

S (standard) U (opt.) X (optional)

F12-30 SAE 'B' - -

13T, 16/32 DP

-40 SAE 'C' 14T, - -

12/24 DP

-60 SAE 'C' 14T, - -

12/24 DP

-80 SAE 'C-C' SAE 'C' SAE 'D'

17T, 12/24 DP 14T,12/24DP 13T, 8/16 DP

-110 SAE 'D' - -

13T, 8/16 DP

= Max 5100 psi (350 bar) operating pressure.

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F12-30, -40, and -60

(SAE versions with 2 bolt flange)

Catalogue HY17-8249/US

Installation dimensions

Ø D10

(x2)

A10

B10

G11

J11

D11

A11 B11

C11

N11

L12

A12

B12

C12

G12

Port A Port B Port D

H12

K12

J12

F12

D12 (thread)

Type T

flange

Ø E12

L11

M11

Ø E11

Ø F11

K11

H11

Port C

(inspection/

drain port)

Type T

key shaft

R11

Q11

See

table

Type S spline shaft

F10

E10 R

C10 R

Flushing

valve

(optional)

Speed

sensor

(optional)

Shown: F12-60 with 2 bolt flange

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Installation dimensions

Ports F12-30 F12-40 F12-60

A, B size

Screw

"-16

thread

(0.87) (0.79) (0.87)

C thread

"-16

"-14

D thread

"-16

"-14

A, B (main ports): SAE J518c (6000 psi)

C, D (drain ports): O-ring boss (SAE J514)

1) UN thread (depth in inches).

Spline shaft(SAE J498b, class 1, flat root, side fit)

Type S

F12-30 SAE 'B'

13 T; 16/32 DP

-40 SAE 'C'

14 T; 12/24 DP

-60 SAE 'C'

14 T; 12/24 DP

Mounting flange (SAE J744)

Type T

F12-30 SAE 'B', 2 bolt

-40 SAE 'C', 2 bolt

-60 SAE 'C', 2 bolt

Key shaft (SAE J744)

Type T

F12-30 1" dia. SAE 'B-B'

-40 1

" dia. SAE 'C'

-60 1

" dia. SAE 'C'

Dim. F12-30 F12-40 F12-60

A10 5.75 7.13 7.13

B10 6.93 8.46 8.46

C10 2.48 2.91 2.91

D10 0.57 0.69 0.69

E10 0.39 0.63 0.63

F10 0.39 0.61 0.61

A11 3.94 4.33 4.92

B11 2.32 2.56 2.76

C11 0.98 1.02 0.87

D11 0.25 0.31 0.31

E11 1.30 1.65 1.65

F11 4.000/ 5.000/ 5.000/

3.998 4.998 4.998

G11 7.46 7.76 8.43

H11 0.31 0.31 0.31

J11 1.50 1.89 1.89

K11 2.80 3.03 3.21

L11 1.25 1.50 1.50

M11 0.10 0.16 0.16

N11 6.06 6.34 7.03

Q11 1.02 1.06 1.06

R11 1.30 1.89 1.89

A12 4.80 5.28 5.67

B12 2.60 2.60 2.60

C12 0.937 0.937 0.937

D12

* 5

"-24

E12 1.000/ 1.250/ 1.250/

0.998 1.248 1.248

F12 1.11 1.39 1.39

G12 6.06 6.34 7.03

H12 0.38 0.50 0.50

J12 0.63 0.75 0.75

K12 2.000 2.000 2.000

L12 0.71 0.79 0.79

* UNF-2B thread

Main ports A and B, type U (optional)

F12-30 1

" - 12 UN

-40 1

" - 12 UN

-60 1

" - 12 UN

O-ring ports according to SAE J514d

= Max 350 bar operating pressure.

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-150

(CETOP version)

Catalogue HY17-8249/US

Installation dimensions

4.29

0.98

6.26

12.09

6.77 4.65

0.71

Drain port D

BSP 3/4"

Ø2.24

min

Ø7.8740

7.8712

Ø9.84

Ø0.87(x4)

9.29 max

9.29

Approx.

center of

gravity

R 0.04

14x9x70

(0.55x0.35x2.76;

metric key)

R 0.03

Flange C

Type C mounting flange

8.74 max

3.98

3.35

2.11

3.125

1.18

9.84

1.97

3.23

1.81

ØM16(x8)*

1.44

Main port A

1 1/2" **

Main port B

1 1/2" **

Drain port C

BSP 3/4"

Ø1.9692/

1.9686

M16

(metric thread)

Type K key shaft

1.97

W45x2x21x9g

(metric spline)

Spline shaft D (DIN 5480)

* Metric thread, deep1.4

** 6000 psi flange (SAE J581c)

1.18

M16

(metric thread)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-150

(SAE version)

Catalogue HY17-8249/US

Installation dimensions

8.74 max

3.98

3.35

1.94

3.13

1.18

11.69

6.18

0.94

8.11

13.98

0.31

2.63

0.50

ØM16* (x8)

1.437

6.77 4.65

0.71

Main port A

1 1/2" **

Main port B

1 1/2" **

Drain port C

BSP 3/4"

Drain port D

BSP 3/4"

Ø1.750/

1.748

Ø2.24

min

Ø6.000/

5.998

"x2

(key)

Key shaft T

SAE 'D'

(SAE J744c)

Ø0.83 (x4)

8.43 max

7.56

6.362

Approx.

center of

gravity

R 0.04

R 0.03

0.31

2.63

SAE 'D'; 13T, 8/16 DP;

class 1, flat root, side fit

Spline shaft S (SAE J498b)

Mounting flange S

SAE 'D' (SAE J744c)

Flange S

* Metric thread, deep1.4

** 6000 psi flange (SAE J581c)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11-250

(SAE version)

Catalogue HY17-8249/US

Installation dimensions

9.13

3.98

5.55

3.125

M16 (metric

thread)

13.23

6.36

8.11

max

0.50

1.22

R 0.03

M16 (x8)

1.4 deep

(metric

thread)

1.437

7.76 4.65

0.94

1.06

Main port A

1 1/2" *

Main port B

1 1/2" *

Drain port C

BSP 3/4"

Drain port D

BSP 3/4"

2.11

Ø6.000/

5.998

6.36

8.11 max

Ø0.83

(x4)

Ø1.9692/

1.9686

Type K key shaft

(metric; not SAE)

14x9x70

(0.55x0.35x2.76;

metric key)

Ø2.24

min

Ø1.54

(x2)

7.09

15.55

3.23

0.31

8.50

Approx.

center of

gravity

R 0.03

0.31

2.63

1.38

Mounting flange S

SAE 'D' (SAE J744c)

Spline shaft F (SAE J498b)

SAE F; 15T, 8/16 DP;

class 1, flat root, side fi

Optional:

SAE S; 13T, 8/16 DP

* 6000 psi flange (SAE J581c)

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

F11 with built-in

make-up valve

Saw bar supported

directly on the

motor flange

Feed

cylinder

Chain spur gear mounted

directly on the shaft

Saw

chain

Protective

cover

Saw

bar

Port A Port B

Port G

Only for F11-10, -19

(for make-up flow

if required)

Port C/D

Chain saw installation (example; F11-10 shown)

F11 fan motors

Frame sizes -10, -14 and -19 are also available as 'fan

motors' with a built-in check valve (refer to the sche-

matic below) and CETOP mounting flange. Just like the

saw motor, the fan motor can be operated at very high

speeds without reliability problems.The fan is usually

installed directly on the motor shaft without additional

bearing support.

Additional information (available versions, ordering

codes, installation dimensions, etc.) is available in

publication 'F11 Fan Motors'

(catalogue 9129 8247-02).

Fan motor (F11-10 shown).

Fan motor schematic (left hand rotation shown).

F11 saw motors

Series F11 motors have proven extremely reliable in

demanding applications such as bar (chain) saws.

Primarily due to the 40° bent-axis design, spherical

pistons (with laminated piston rings) and gear synchro-

nization, very high speeds are permissible. Not even

low temperatures at start-up affect reliability.

To further enhance the saw function and, at the same

time, reduce weight, cost and installation dimensions, a

specific saw motor has been developed (frame sizes

-10, -14 and -19; refer to the illustration to the right)

which is specifically dedicated to bar saws. The motor

allows the saw bar bearings to be mounted directly on

the motor housing, and the spur gear installs on the

motor shaft without any additional bearings.

For more detailed information (available versions,

ordering codes, installation dimensions, etc.), refer to

'F11 Saw Motors' (catalogue 9129 8245-02).

Catalogue HY17-8249/US

Technical information

Built-in

make-up

valve

Mounting

flange C

(CETOP)

Key shaft

(CETOP)

Port GMain port B

Main port A

Drain port C

Alternative

drain port D

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Integrated flushing valve

(F12-30, -40, -60, -80)

Nozzle

(optional)

Port A

Port B

Built-in

flushing

valve

Nozzle

(optional)

FV13 flushing

valve block

Nozzle

(optional)

Port A

Port B

Nozzle (optional)

FV13 flushing

valve block

F12 accessory valve blocks

Type FV13 flushing valve (for F12-110)

A separate flushing valve block is available for the

F12-110. It has the same function as the integrated

valve for the other F12 frame sizes (above).

The valve block mounts between the motor port flange

and the split flanges as shown to the right.

An optional nozzle can be installed in the valve block

drain port.

Ordering code: FV13

NOTE: Additional information is available in

publication ’Mobile motor/pump accessories’

(catalogue HY17-8258/UK).

F12 integrated flushing valve

(F12-30, -40, -60 and -80)

Series F12 (except F12-110; refer to the FV13 flushing

valve block below) is available with an integrated

flushing valve which provides the rotating parts with an

additional cooling flow, required when operating at high

speeds and power levels.

In a hydrostatic transmission, the valve also ensures

that part of the main circuit fluid is being removed and

replaced by cool, filtered fluid from the charge pump.

The flow is limited by a suitably sized nozzle that

installes below a plug in the motor port flange.

NOTE: Ordering code, available nozzles and

other information is provided in publica-

tion ’Mobile motor/pump accessories’

(catalogue HY17-8258/UK).

Catalogue HY17-8249/US

Technical information

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

BT brake

valve block

BT brake

valve block

F12-

motor

Brake release valve

flushing valve etc.

Port BR

(brake

release)

Port A

Port B

Port S

(make-up)

Port G

SR valve block

Type SR pressure relief/make-up valve

The SR pressure relief/make-up valve block for series

F12 motors is designed to protect the motor from high

pressure spikes as well as provide an excellent make-

up function to help prevent motor cavitation (when port

G is pressurized).

The valve block mounts between the motor port flange

and the split flanges (as shown to the right).

The SR block is available in three sizes:

- SR11 (

") for F12-30, -40, -60

- SR12 (1") for F12-80

- SR13 (1

") for F12-110

NOTE: - For additional information such as

pressure settings and installation

dimensions, refer to publication

’Mobile motor/pump accessories’

(catalogue HY17-8258/UK).

- To obtain a combined cross-over relief/

make-up and flushing function on the

F12-110, the SR13 and FV13 valve

blocks can be stacked (with the flushing

valve block mounted next to the motor).

Type BT brake valve

When a motor (in an open loop system) is used in a

hydrostatic vehicle transmission, the motor may

operate faster than what corresponds to the available

pump flow (e.g. in a steep downhill); this can lead to

motor cavitation and loss of braking power.

The BT brake valve prevents cavitation by throttling

the return flow from the motor as soon as the pressure

level in the inlet port decreases to approximately 35

bar. At the same time, motor braking is provided when

the pump flow decreases or is shut off.

The BT brake valve can be supplied with various

optional functions such as a mechanical brake release

valve and a flushing valve.

The valve block is very compact and installs between

the motor port flange and the split flanges

(refer to the illustration).

The BT valve block is available in two sizes:

- BT21 (

") for F12-30, -40, -60

- BT22 (1") for F12-80

NOTE: Detailed information on the BT valve is

provided in publication

’Mobile motor/pump accessories’

(catalogue HY17-8258/UK).

Catalogue HY17-8249/US

Technical information

Port A

Port B

Port G SR valve block F12-motor

Port L

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

SV pressure relief

valve block

SV valve block

Port A

Port B

(Port L)

Speed

sensor

Type SV pressure relief valve

The SV pressure relief valve for series F12 motors

protects the motor and the corresponding main hy-

draulic lines from pressure spikes. Like the SR valve

block (page 31), it has integrated cartridge type

pressure relief valves and mounts between the motor

port flange and the split flanges as shown to the right.

The design of the relief valves permits a limited make-

up flow (when port L is pressurized).

The SV valve block is available in three sizes:

- SV11 (

") for F12-30, -40, -60

- SV12 (1") for F12-80

- SV13 (1

") for F12-110

NOTE: - Detailed information on available

pressure settings, installation dimen-

sions, etc. is provided in publication

’Mobile motor/pump accessories’

(catalogue HY17-8258/UK).

- On the F12-110, the FV13 flushing valve

block (page 36) can be mounted between

the SV13 block and the motor port flange

to obtain a combined pressure relief and

flushing function.

Speed sensor

A speed sensor kit is available for series F11/F12.

A ferrostat differential (Hall-effect) sensor installs in a

separate, threaded hole in the F11/F12 bearing

housing.

On F12 the speed sensor is directed towards the ring

gear.On F11 the speed sensor is directed towards the

pistons. The speed sensor outputs a square wave

signal within a fequency range of 5 Hz to 20 kHz.

NOTE: - The motor bearing housing must be

prepared for the speed pick-up;

refer to the F11/F12 ordering codes

(pages 7-12).

- On F11 the pistons position must be

known before mounting.

- Additional information is provided in

’Mobile motor/pump accessories’

(catalogue HY17-8258/UK).

- The speed sensor is also shown in the

illustrations on pages 19, 21, 22, 24, 26

and 28.

Catalogue HY17-8249/US

Technical information

F12 with speed sensor.

F11-14 with speed sensor.

Speed

sensor

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

hose

Suction

fitting

(Split-flange

half)

(Mounting

screw)

(O-ring)

Suction fittings

To minimize the risk for cavitation when operating the

F12 as a pump, we recommend using our suction

fittings; all take 2" hoses.

Part no. SAE size For L [inch]

379 4070

" F12-30 3.94

F12-40

F12-60

370 4095 1" F12-80 3.94

370 3916 1

" F12-110 4.02

The suction fittings are designed for use with standard

SAE or metric split-flange halves as shown.

O-ring and mounting screw sizes are listed below.

SAE O-ring Screw size

size dimension [mm] SAE Metric

" 30.0x3.53

"-16x1.50 M10x35

1" 32.9x3.53

"-14x1.50 M12x40

" 37.7x3.53

"-13x1.75 M14x45

Suction fitting kits

Suction fitting kits are available for the F12 ISO and

Cartridge versions. A kit consists of a suction fitting

(shown above), two split-flange halves, an

O-ring and four mounting screws.

Part no. SAE size For Screw size

379 4421

" F12-30/-40/-60 M10x35

370 4098 1" F12-80 M12x40

370 3926 1

" F12-110 M14x45

Split-flange kits

Separate metric split-flange kits, consisting of two split-

flange halves and four mounting screws for use on the

F12 ISO and cartridge versions, are also available.

Part no. SAE size For Screw size

379 4405

" F12-30/-40/-60 M10x35

370 4329 1" F12-80 M12x40

370 4330 1

" F12-110 M14x45

F12 main port suction fittings

(Split-flange

half)

(Mounting

screw)

Catalogue HY17-8249/US

Technical information

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Clockwise rotation

Port A Port B

Counter

clockwise

rotation

Direction of rotation

The M and H versions of series F11, and the M version

of series F12, are bi-directional.

The L and R pump versions are uni-directional, allow-

ing higher selfpriming speeds

(refer to page 14).

The illustration to the right shows direction of flow

versus shaft rotation. In a motor application, the shaft

turns clockwise when port B (black arrow) is pressu-

rized, and counter clockwise when port A (open arrow)

is pressurized.

In a pump application where the shaft turns clock-wise,

port B is the inlet port and should be connected to tank;

when the shaft turns counter clockwise, port A is the

inlet port.

Hydraulic fluids

Ratings and performance data for series F11/F12 are

based on operating with good quality, contamination-

free, petroleum-based fluids.

Hydraulic fluids type HLP (DIN 51524), automatic

transmission fluids type A, or API CD engine oils can

be used.

Fire resistant fluids (when used under modified operat-

ing conditions) and synthetic fluids may also be suit-

able.

For additional information, refer to Hydraulic Marketing

IS data base:

- Hydraulic fluid specifications

- Fire resistant fluids.

Operating temperature

The following temperatures should not be exceeded

(type H and N shaft seals):

Drain fluid: 195 °F

(90 °C)

Viton shaft seals (F11 type E, F12 type V) can be used

to 240 °F

(115 °C)

drain fluid temperature.

NOTE: The temperature should be measured at

the utilized drain port.

Continuous operation may require case flushing in

order to meet the viscosity and temperature limitations.

The following table shows operating speeds, above

which flushing is usually required, as well as suggested

flow through the case.

NOTE:

When operating the F11/F12 as a pump above the

selfpriming speed (valid for both the pump and

motor versions), the inlet must be sufficiently

pressurized. Increased noise and deteriorating

performance may otherwise be experienced.

For further information refer to ’Selfpriming speed

and required inlet pressure’ on page 6.

Catalogue HY17-8249/US

Installation information

Series F12

Frame size Speed [rpm] Flow [l/min] Flow [gpm]

F12-30 3500 4–8 1.0–2.1

F12-40 3000 5–10 1.3–2.6

F12-60 3000 7–14 1.9–3.7

F12-80 2500 8–16 2.1–4.2

F12-110 2300 9–18 2.4–4.8

Series F11

Frame size Speed [rpm] Flow [l/min] Flow [gpm]

F11-5 5500 1–2 0.25-0.5

F11-10 4500 2–3 0.5-0.8

F11-14 4500 2–3 0.5-0.8

F11-19 4000 2–4 0.5-1.0

F11-150 2200 10–20 2.6-5.2

F11-250 1800 12–22 3.2-5.8

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Catalogue HY17-8249/US

Installation information

Shaft seal H/V

H/V

F12-30 205

100

50 -

F12-40 175

F12-60 175

F12-80 145

-- --

F12-110 140

-- -- --

Max recommended case pressure versus shaft speed -

F12 seal types H or V, and N

Series F12

Shaft seal H/V

N/E

H/V

N/E

H/V

N/E

H/V

N/E

H/V

N/E

H/V

N/E

H/V

N/E

H/V

N/E

H/V

N/E

H/V

N/E

F11-5 20

2.2

1.9

1.6

1.3

6.5

0.9

0.6

4.2

0.5

0.3

3.5

0.2

F11-10 20

2.2

11.5

1.8

8.5

1.2

1.0

5.5

0.7

0.5

3.8

0.4

3.5

0.2 3.0 0 - -

F11-14 19

2.2

9.5

1.5

1.0

5.5

0.8

4.5

0.5

3.5

0.4

3.0

0.2

2.5

-- --

F11-19 19

2.2

9.5

1.4

0.9

5.5

0.6

4.5

0.4

3.5

0.3

3.0

0-- ----

F11-150 9.5

2.2

4.5

0.6-- -- -- -- -- -- -- --

F11-250 9.5

4.5

-----------------

Max case pressure [psi]

versus shaft speed [rpm]

peed

1500 3000 4000 5000 6000 8000 9000 10000 11000 12000

Max recommended case pressure versus shaft speed - F11 seal types H or V and N or E.

Max case pressure [psi] vs. shaft speed [rpm]

peed

1500 3000 4000 5000 6000

Series F11

Viscosity

The ideal operating range is75 to 150 SUS

(15 to 30 mm

/s).

At operating temperature, the viscosity (of the drain

fluid) should be kept above 46 SUS (8 mm

/s [cSt]).

At start-up, the viscosity should not exceed

5 000 SUS (1000 mm

/s)

Filtration

To obtain the highest service life of the F11/F12,

the fluid cleanliness should meet or exceed

ISO code 18/13 (ISO 4406).

During normal operating conditions, a 10 µm

(absolute) filter is recommended.

Case pressure

The tables below show the highest recommended

case pressure as a function of shaft speed.

‘Nominal’ shaft seal life can be expected at a certain

speed and the corresponding max case pressure. Seal

life will be shorter, however, at unfavourable operating

conditions (high temperature, low oil viscosity,

contaminated oil).

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Port C

Port E

(F12-110)

Port D

Drain flow

Flushing flow

(when required)

Spring loaded

check valve

Drain flow

Case drain connections

Series F11/F12 have two drain ports, C and D, while

F12-110 has an additional port, E.

The uppermost drain port (such as port C in the illus-

tration below) should always be utilized.

In mounting positions such as 'shaft up' (below)

a spring loaded check valve should be installed in the

drain line in order to insure a sufficiently high oil level

in the case.

Preferably, the drain line should be connected directly

to the reservoir.

Before start-up

Make sure the F11/F12 case as well as the entire

hydraulic system is filled with a recommended fluid.

The internal leakage, especially at low operating

pressures, is

not

sufficient to provide lubrication at

start-up.

NOTE:

- To avoid cavitation and obtain a low noise level as

well as reduced heat generation, tubes, hoses and

fittings must be adequately dimensioned.

- Preferably, the suction line flow speed should be

1.5 to 3.5 fps (0.5 to 1 m/s), and pressure line flow

speeds 10 to 16 fps (3 to 5 m/s).

- For series F12, suitable suction fittings are available

(refer to page 39).

Catalogue HY17-8249/US

Installation information

Parker Hannifin

Mobile Controls Division

Trollhättan, Sweden

Hydraulic motor/pump

Series F11/F12

Offer of Sale

Please contact your Parker representation for a detailed ”Offer of Sale”.

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED

HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide

product and/or system options for further investigation by users having technical expertise. It is important that you analyze all

aspects of your application, including consequences of any failure, and review the information concerning the product or

system in the current product catalogue. Due to the variety of operating conditions and applications for these products or

systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and

systems and assuring that all performance, safety and warning requirements of the application are met.

The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are

subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.

WARNING

Catalogue HY17-8249/US

General information

Parker Hannifin is the world’s premier supplier of motion and control systems

and solutions, with sales and manufacturing facilities throughout the world.

For product information and details of your nearest Parker sales office, visit us

at www.parker.com or call free on 1-800-272-7537 (North America).

Hydraulics Group

Sales Offices

Catalogue HY17-8249/US

2M 03/04 RT

Parker Hannifin Corporation

North America

USA, Canada

100 Parker Drive

Otsego, MI 49078

USA

Tel: +1 269-694-9411

Fax: +1 269-694-4638

Mexico

Via de Ferrocarril a Matamoros #730

Apodaca, N.L.

Mexico

C.P. 6 6 6 0 0

Tel: +52 81 56 6000

Fax: +52 81 56 6076

Latin America

Pan American Division

7400 N.W. 19th Street

Suite A

Miami, FL 33126

USA

Tel: +305 470 8800

Fax: +305 470 8808

Argentina

Stephenson 2711

(1667) Tortuguitas–Malvinas Argentinas

Pcia. de Buenos Aires

Argentina

Tel: +54 11 4752 4129

Fax: +54 11 4752 3704

Brazil

Av. Lucas Nogueira Garcez

2181 Jacarei, SP Brazil 12300-000

Brazil

Tel: +55 12 354 5100

Fax: +55 12 354 5262

Chile

Av. Americo Vespucio 2760-C,

Conchali

Santiago

Chile

Tel: +56 2 623 1216

Fax: +56 2 623 1421

Venezuela

Av. Principal de Boleita Norte con Calle Miraima,

Edf. Draza, Planta Baja

Caracas 1070

Venezuela

Tel: +58 212 238-5422

Fax: +58 212 239-2272