652 Series | Filter Regulator Lubricator (FRL)
www.numatics.com
Air Preparation Products
Table of Contents
652 Series
Product Overview 2-3
Particulate Filter 4-6
Coalescing Filter 7-9
Adsorber - Activated Carbon 7-9
Regulator 10-12
Manifold Regulator 13-15
Particulate Filter/Regulator 16-18
Coalescing Filter/Regulator 19-21
Lubricator 22-24
Shut-Off Isolation Valve 25-27
Slow Start-Quick Exhaust Valve 28-30
Diverter Block 31-32
Lockout Valve 33-34
652 Series Air Preparation Manifold Assemblies 35-36
Mounting Bracket Dimensional Drawings 37
Bowl and Drain Features 38
280 Series Digital Pressure Switch 39
PS182 Series Pressure Switch 40
PS180 Series Pressure Switch 41
Digital Pressure Gauge 41
349 Series Pressure Switch 42
Electric Differential Pressure Indicator (DPI) 43
Electronic Liquid Level Indicator 43
Kits and Service Parts 44-51
Flow Charts 52-55
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
2
SERIES
652
1) Provision for Key Lockable (Regulator & F/R*)
2) Tamper Resistant (Regulator & F/R*)
3) Key Lockable (Regulator & F/R*)
4) Scissor Lock
5) Electric Differential Pressure Indicator
(Coalescing Filter)
6) Differential Pressure Visual Pop-Up Indicator
(Coalescing Filter)
7) No Differential Pressure Indicator
8) Vertical Solenoid (DIN Connector with & w/o LED)
9) Horizontal Solenoid without DIN Spade Coil
without Connector
10) Horizontal Solenoid with 3 Pin M12 Connection
11) Pilot Air Operated
12) Horizontal Solenoid (DIN Connector with
& w/o LED)
13) Panel Nut/Panel Bracket (Regulator & F/R*)
14) Panel Nut (Regulator & F/R)
15) Side Mounting Brackets
16) End Plates, Body-to-Body Clamps & Wall/Panel
Brackets
17) End Plates & Body-to-Body Clamps
18) Polyethylene Muffler
19) Metal Muffler
20) Electronic Liquid Level Indicator
21) Semi-Automatic/Manual Drain
22) No Drain
23) Manual Drain – Stainless Steel
24) Automatic Drain – Normally Open – Brass
25) Low Profile Gauge
26) Low Profile Gauge with Pressure Range
Indicators
27) No Gauge Port
28) Port Plate
29) Digital Pressure Switch – DPS 280 Series
30) Round Gauge
31) Digital Gauge
32) Polycarbonate Bowl & Guard
33) Metal Bowl with Polyamide Sight Gauge
34) Metal Bowl with Borosilicate (Glass) Sight
Gauge
35) Metal Bowl without Sight Gauge
652 Series - Product Overview
Air Preparation Manifold Assembly
& Optional Features
1
4
15
16
16
6
15
10
14
13
27
33
22
19
19
18
18
20
21
32
25
23
24
34
35
26
17
17
28
29
30
31
5
7
8
9
12
2
3
11
Filter/Regulator
Lubricator
Shut-Off
Isolation
Valve
Particulate
Filter
Coalescing
Filter
Wall/Panel
Bracket
Body-to-Body
Clamps
Diverter
Block
Regulator
Slow-Start/
Quick Exhaust
Valve
*F/R = Filter/Regulator
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
3
SERIES
652
652 Series Modular Assembly Mounting Features
Body-to-Body Assembly Clamp
(Kit# P652AT502466001 - NBR Seal)
Easy to assemble Body-to-Body clamp, with captive
screws. Available with NBR or FKM Seal. Products are
easily assembled in seconds.
Side Mounting Brackets (Kit# P652AT503860002)
The "Side Mounting Brackets" are typically used to
mount single units, but could also be used to mount
multiple units. Note: All ports are threaded as standard.
End Plates with Body-to-Body Assembly Clamp
(Kit# T652AT502468001 - NPTF/NBR Seal)
The "End Plate" feature allows the user to easily remove
the 652 series air prep assembly without having to
remove the piping. Simply loosen the screws on the
Body-to-Body assembly clamps, and the manifold is
easily removed in seconds. The kit includes Inlet/Outlet
plates, Body-to-Body clamps and o-rings. Available with
1/2 NPTF, ISO228/1-G & ISO 7/1-Rc (NBR or FKM).
Wall/Panel Bracket (Kit# P699AT502467001)
The Wall/Panel Bracket feature is the primary mounting
feature for the 652 series air prep assemblies. The user
can attach one bracket at each end of the manifold or
can attach as many as desired for each station. These
brackets easily attach to the back of the Body-to-Body
assembly clamps using two screws. In addition, this
bracket can be used as a support bracket in between
any station on the manifold.
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
4
SERIES
652
• Large selection of filtering capacities to remove particulate and water
droplets from compressed air or inert gas
• Sintered polyethylene elements, with centrifugal separator, include 5, 25
and 40 Microns
• Optional extended temperature range of -40°F to 176°F (-40°C to 80°C)
• Innovative two position plastic drain with manual and semi-automatic
functions. Additional drains include an automatic style (brass) and
manual (stainless steel)
• Polycarbonate and Aluminum bowls with a selection of sight gauge
materials that meet industry and application requirements
• Threaded ports allow for individual or modular mounting
• Air purity class according to ISO 8573-1: 2010
Performance Data
Port Sizes 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow - Per ISO 6358
P1 = 91.4 PSI (6.3 bar)
∆P = 14.5 PSI (1 bar)
Micron Rating SCFM (L/min ANR)
1/4
5 μm 70.8 (2024)
25 μm 89.3 (2550)
40 μm 92.4 (2640)
3/8
5 μm 76.5 (2185)
25 μm 118.7 (3390)
40 μm 135.5 (3870)
1/2
5 μm 80.2 (2290)
25 μm 129.5 (3700)
40 μm 153 (4370)
Maximum Inlet Pressure PSIG (bar)
Polycarbonate Bowl 232 (16)
Aluminum Bowl 232 (16)
Ambient Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg)
Polycarbonate Bowl 0.94 (0.426)
Aluminum Bowl 1.22 (0.553)
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Filter Element Sintered Polyethylene
Bowl Polycarbonate or Aluminum
PARTICULATE FILTER
Air Purity Class - ISO 8573-1: 2010*
5 μm (5:8:4)
25 μm (6:8:4)
40 μm (7:8:4)
* Maximum flow at 91.4 PSI (6.3 bar) inlet pressure to maintain
air purity class is 20.0 SCFM (566 L/min)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
5
SERIES
652
How to Order
Particulate Filter
* Conforms to ISO standards 1179-1
** Compressed air must be dry enough so no ice formation is present on the
product. All bowls should be emptied prior to ambient temperatures dropping
below 32°F (0°C)
*** If multiple options are required, please use the on-line CAD configurator on the
website to generate the part number (www.numatics.com), or consult factory.
8 652 A B B P 4 J A00 0 N
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
B = Filter - Particulate
Elements
A = 40 Micron
B = 5 Micron
J = 25 Micron
Bowl Type
K = Metal Bowl without Sight Gauge
L = Metal Bowl with Sight Gauge (Glass)
M = Metal Bowl with Sight Gauge (Polyamide)
P = Polycarbonate Bowl with Bowl Guard
Options***
A00 = No Options
101 = Side Mounting Brackets
105 = High Temperature (80°C/176°F)
106 = Low Temperature (-40°C/-40°F)**
109 = FKM Seals
113 = Stainless Steel Fasteners
117 = ATEX Zones 1-21
202 = 105 + 109
2A9 = 105 + 106
Drain Type
0 = No Drain
A = Auto Drain Normally Open
N = Manual - Semi-Automatic Drain
Q = Manual Drain - Stainless Steel
K/L/M
A J
P
B
101
A QN
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
6
SERIES
652
Dimensional Drawing - 652 Series Particulate Filter
Dimensions: mm (Inches)
J
E
H
F
L
K
T
C
D
S
M
Q
R
A*
G*
B
N
P
A B C D E F G H J
217 38.3 66 33 69 34.5 25 50 1.9
(8.54) (1.51) (2.60) (1.30) (2.72) (1.36) (0.98) (1.97) (0.07)
K L M N P Q R S T
53 106 11 10 20 6.3 5.5 42 84
(2.09) (4.17) (0.43) (0.39) (0.39) (0.25) (0.22) (1.65) (3.30)
* Variable dimension based on type of drain that is specified; If an Automatic Drain is specified,
add another 5 mm to "G" dimension, which also adds 5 mm to the "A" dimension.
Cross Section - 652 Series
Particulate Filter
To remove bowl allow 75 mm
(2.95in) from the bottom of the
bowl drain.
12
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
7
SERIES
652
Performance Data
Port Sizes 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow - Per ISO 6358
P1 = 91.4 PSI (6.3 bar)
∆P = 5 PSI (0.35 bar)
Micron Rating SCFM (L/min ANR)
1/4
0.3 μm 28.0 (801)
0.01 μm 25.0 (714)
3/8
0.3 μm 28.6 (817)
0.01 μm 27.5 (785)
1/2
0.3 μm 30.5 (870)
0.01 μm 29.1 (831)
Maximum Inlet Pressure PSIG (bar)
Polycarbonate 232 (16)
Aluminum 232 (16)
Ambient Temperature Range °F (°C) 35 to 122 (1.7 to 50)
Fluid Temperature Range °F (°C) 35 to 122 (1.7 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg)
Polycarbonate Bowl 0.98 (0.442)
Aluminum Bowl 1.25 (0.569)
• Extensive range of coalescing filter elements to remove oil and sub-micron
particles down to 0.01 microns. Air purity class according to ISO 8573-1:
2010
• Optional 3 micron pre-filter integrated in the coalescing element eliminates
the need for a separate particulate element. Coalescing filter elements include
0.3 and 0.01 microns
• Adsorber filter (activated carbon) for removal of odors and hydrocarbon vapor
• Innovative two position plastic drain with manual and semi-automatic
functions. Additional drains include an automatic style (brass) and manual
(stainless steel)
• Polycarbonate and Aluminum bowls with a selection of sight gauge materials
that meet industry and application requirements
• Optional extended temperature range of 176°F (80°C)
• Visual or electrical differential pressure Indicators for condition monitoring
of filter element
COALESCING FILTER & ADSORBER
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Coalescing Filter Element Borosilicate Microfiber & Polyester
Filter Element End Cap Polypropylene
Adsorber Activated Carbon
Bowl Polycarbonate or Aluminum
Air Purity Class - ISO 8573-1: 2010*
0.3 μm (3:7:3)
0.01 μm (2:7:2)
* Maximum flow at 91.4 PSIG (6.3 bar) inlet pressure to maintain
stated air purity class is 10.6 SCFM (303 L/min)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
8
SERIES
652
How to Order
Coalescing Filter
* Conforms to ISO standards 1179-1
** If multiple options are required, please use the on-line CAD configurator on the
website to generate the part number (www.numatics.com), or consult factory.
8 652 A F D P 4 H A00 0 N
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
A = Adsorber - Activated Carbon
F = Filter - Coalescing
Elements
D = 0.3 Micron - Coalescer
E = 0.01 Micron - Coalescer
F = Adsorber - Activated Carbon
M = 0.3 Micron Coalescer with 3 Micron Prefilter
N = 0.01 Micron Coalescer with 3 Micron Prefilter
Bowl Type
K = Metal Bowl without Sight Gauge
L = Metal Bowl with Sight Gauge (Glass)
M = Metal Bowl with Sight Gauge (Polyamide)
P = Polycarbonate Bowl with Bowl Guard
Options**
A00 = No Options
101 = Side Mounting Brackets
105 = High Temperature (80°C/176°F)
109 = FKM Seals
113 = Stainless Steel Fasteners
117 = ATEX Zones 1-21
202 = 105 + 109
Drain Type
0 = No Drain
A = Auto Drain Normally Open
N = Manual - Semi-Automatic Drain
Q = Manual Drain - Stainless Steel
Indication Type
E = Electric Differential Pressure Indicator
H = Differential Pressure Visual Pop-Up
Indicator
J = No Differential Pressure Indicator
K/L/M
D/M F
P
E/N
101
A
E
QN
H
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
9
SERIES
652
Dimensional Drawing - 652 Series Coalescing Filter and Adsorber Filter
Cross Section - 652 Series
Coalescing Filter
Dimensions: mm (Inches)
J
E
FH
L
K
C
D
M
Q
R
B
A*
P
N
G*
T
S
A B C D E F G H J
233 54.4 66 33 69 34.5 25 50 1.9
(9.17) (2.14) (2.60) (1.30) (2.72) (1.36) (0.98) (1.97) (0.07)
K L M N P Q R S T
53 106 11 10 20 6.3 5.5 42 84
(2.09) (4.17) (0.43) (0.39) (0.79) (0.25) (0.22) (1.65) (3.30)
* Variable dimension based on type of drain that is specified; If an Automatic Drain is specified,
add another 5 mm to "G" dimension, which also adds 5 mm to the "A" dimension.
To remove bowl allow 88 mm
(3.14in) from the bottom of the
bowl drain.
12
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
10
SERIES
652
• High flow with a wide range of adjustable output pressure ranges
• Flows in excess of 245 SCFM (7000 L/Min ANR)
• Available with relieving, non-relieving and internal flow check options
• Optional low profile gauge, round gauge, digital gauge or digital
pressure switch
• Optional extended temperature range of -40°F to 176°F (-40°C to 80°C)
• Threaded ports allow for individual or modular mounting
• Key lockable and tamper proof options
Performance Data
Port Size 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow - Per ISO 6358
P1 = 145 PSI (10 bar)
P1 = 91.4 PSI (6.3 bar)
∆P = 14.5 PSI (1 bar)
SCFM (L/min ANR)
1/4 144.2 (4120)
3/8 228.6 (6530)
1/2 245.0 (7000)
Maximum Inlet Pressure PSIG (bar) P1 232 (16)
Adjustable Pressure Ranges PSIG (bar) P2
3 to 45 (0.2 to 3)
3 to 60 (0.2 to 4)
7 to 125 (0.5 to 8)
7 to 145 (0.5 to 10)
Ambient Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg) 0.95 (0.431)
REGULATOR
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Springs Stainless Steel
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
11
SERIES
652
How to Order
Regulator
* Conforms to ISO standards 1179-1
** Relieving Standard; use option 121 for Non-Relieving
*** Compressed air must be dry enough so no ice formation is present on the product.
**** If multiple options are required, please use the on-line CAD configurator on the
website to generate the part number (www.numatics.com), or consult factory.
8 652 A R 0 0 4 F A00 G 0
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
K = Regulator with Internal Flow Check
R = Regulator**
W = Pilot Operated Regulator
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
Gauge Type
B = Digital Pressure Switch - PNP
C = Digital Pressure Switch - NPN
D = Digital Gauge
F = Low Profile Gauge PSI/bar
G = Low Profile Gauge bar/PSI
H = Low Profile Gauge PSI/bar with Pressure Range Indicator
J = Low Profile Gauge bar/PSI with Pressure Range Indicator
N = No Gauge with Port Plate (1/8 NPTF)
P = No Gauge with Port Plate (1/8 ISO 7/1 Rc)
Q = Round Gauge bar/PSI
R = Round Gauge PSI/bar
0 = No Gauge Port
Options****
A00 = No Options
101 = Side Mounting Brackets
102 = Panel Nut
103 = Tamper Resistant
104 = Key Lockable
105 = High Temperature (80°C/176°F)
106 = Low Temperature (-40°C/-40°F)***
109 = FKM Seals
113 = Stainless Steel Fasteners
114 = Provision for Key Lockable Option
117 = ATEX Zones 1-21
119 = Panel Bracket with Panel Nut
121 = Non-Relieving
122 = Bottom Oriented Pressure Adjustment
123 = Gauge Type Mounted for
Right-to-Left Flow
202 = 105 + 109
2A9 = 105 + 106
Pressure Range
D = 3-45 PSIG / 0.2-3 bar
E = 3-60 PSIG / 0.2-4 bar
G = 7-125 PSIG / 0.5-8 bar
H = 7-145 PSIG / 0.5-10 bar
B/C
K/R
N/P
F/G
0
D
W
Q/R
H/J
101
122
104103
123
119
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
12
SERIES
652
Dimensional Drawing - 652 Series Regulator
Cross Section - 652 Series
Regulator
Dimensions: mm (Inches)
A B C D E F G H J K
125 94.5 66 33 69 34.5 2.5 29 14.5 41.75
(4.92) (3.72) (2.60) (1.30) (2.72) (1.36) (0.10) (1.41) (.61) (1.64)
L M N P Q R S ØT V ØW
42 50 20 10 61.5 84 106 7 6.3 11
(1.65) (1.97) (0.79) (0.39) (2.42) (3.30) (4.17) (0.28) (0.25) (0.43)
AA BB CC DD EE
151 120 66 33 55
(5.94) (4.72) (2.60) (1.30) (2.17)
1
2
B
C
D
A
E
F
G
L
S
R
K
N
P
M
V
H
ØT
J
Q
ØW
EE
AA
BB
CC
DD
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
13
SERIES
652
• High flow with a wide range of adjustable output pressure ranges
• Flows of 280 SCFM (8000 L/Min ANR)
• Allows for a common inlet supply pressure within the regulator manifold,
while maintaining several adjustable output pressures
• Standard output adjustment range is 7 to 125 PSIG (0.5 to 8 bar)
• Optional low profile gauge, round gauge, digital gauge and digital
pressure switch
• Optional extended temperature range of -40°F to 176°F (-40°C to 80°C)
• Key lockable and tamper proof options
Performance Data
Port Sizes
P1 (Inlet) 1/2
P2 (Outlet) 3/8
Thread Type NPTF, G & Rc
SCFM (L/min ANR)
Nominal Flow - Per ISO 6358
P1 = 145 PSI (10 bar)
P1 = 91.4 PSI (6.3 bar)
∆P = 14.5 PSI (1 bar)
280 (8000)
Maximum Pressure PSIG (bar) P1 232 (16)
Adjustable Pressure Ranges - PSI (bar) P2
3 to 45 (0.2 to 3)
3 to 60 (0.2 to 4)
7 to 125 (0.5 to 8)
7 to 145 (0.5 to 10)
Ambient Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg) 0.93 (0.422)
MANIFOLD REGULATOR
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Springs Stainless Steel
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
14
SERIES
652
How to Order
Manifold Regulator
* Conforms to ISO standards 1179-1
** Relieving Standard; use option 121 for Non-Relieving
*** Compressed air must be dry enough so no ice formation is present on the product.
***** If multiple options are required, please use the on-line CAD configurator on the website
to generate the part number (www.numatics.com), or consult factory.
8 652 A R 0 0 4 F A00 G 0
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
M = Manifold Regulator**
Port Size
4 = 1/2 In (3/8 Out)
Gauge Type
B = Digital Pressure Switch - PNP
C = Digital Pressure Switch - NPN
D = Digital Gauge
F = Low Profile Gauge PSI/bar
G = Low Profile Gauge bar/PSI
H = Low Profile Gauge PSI/bar with Pressure Range Indicator
J = Low Profile Gauge bar/PSI with Pressure Range Indicator
N = No Gauge with Port Plate (1/8 NPTF)
P = No Gauge with Port Plate (1/8 ISO 7/1 Rc)
Q = Round Gauge bar/PSI
R = Round Gauge PSI/bar
0 = No Gauge Port
Options****
A00 = No Options
101 = Side Mounting Brackets
102 = Panel Nut
103 = Tamper Resistant
104 = Key Lockable
105 = High Temperature (80°C/176°F)
106 = Low Temperature (-40°C/-40°F)***
109 = FKM Seals
113 = Stainless Steel Fasteners
114 = Provision for Key Lockable Option
117 = ATEX Zones 1-21
119 = Panel Bracket with Panel Nut
121 = Non-Relieving
122 = Bottom Oriented Pressure Adjustment
123 = Gauge Type Mounted for
Right-to-Left Flow
202 = 105 + 109
2A9 = 105 + 106
Pressure Range
D = 3-45 PSIG / 0.2-3 bar
E = 3-60 PSIG / 0.2-4 bar
G = 7-125 PSIG / 0.5-8 bar
H = 7-145 PSIG / 0.5-10 bar
M
B/C
N/P
F/G
0
D
Q/R
H/J
101
122
104103
123
119
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
15
SERIES
652
Dimensional Drawing - 652 Series Manifold Regulator
Cross Section - 652 Series
Manifold Regulator
Dimensions: mm (Inches)
A B C D E F G
125 94.5 66 33 69 34.5 3.5
(4.92) (3.72) (2.60) (1.30) (2.72) (1.36) (0.14)
A B C D E
151 120 66 33 55
(5.94) (4.72) (2.60) (1.30) (2.17)
11
A
B
C
G
E
D
F
2
EE
AA
BB
CC
DD
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
16
SERIES
652
Performance Data
Port Sizes 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow - Per ISO 6358
P1 = 145 PSI (10 bar)
P1 = 91.4 PSI (6.3 bar)
∆P = 14.5 PSI (1 bar)
Micron Rating
SCFM (L/min ANR)
1/4
5 μm
133.0 (3800)
25 μm
144.2 (4120)
40 μm
150.5 (4300)
3/8
5 μm
155.8 (4450)
25 μm
189.7 (5420)
40 μm
196 (5590)
1/2
5 μm
157.2 (4490)
25 μm
192.5 (5500)
40 μm
203.0 (5800)
Maximum Inlet Pressure PSIG (bar)
Polycarbonate Bowl
232 (16)
Aluminum Bowl
232 (16)
Adjustable Pressure Ranges PSIG (bar)
3 to 45 (0.2 to 3)
3 to 60 (0.2 to 4)
7 to 125 (0.5 to 8)
7 to 145 (0.5 to 10)
Ambient Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Temperature Range °F (°C) -4 to 122 (-20 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg)
Polycarbonate Bowl 1.20 (0.546)
Aluminum Bowl 1.52 (0.688)
PARTICULATE FILTER/REGULATOR
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Springs Stainless Steel
Filter Element Sintered Polyethylene
Bowl Polycarbonate or Aluminum
• High flow with a wide range of adjustable output pressure ranges
• Optional low profile gauge, round gauge, digital gauge or digital pressure switch
• Optional extended temperature range of -40°F to 176°F (-40°C to 80°C)
• Sintered polyethylene elements, with centrifugal separator, include 5, 25 and 40 Microns
• Threaded ports allow for individual or modular mounting
• Innovative two position plastic drain with manual and semi-automatic functions.
Additional drains include an automatic style (brass) and manual (stainless steel)
• Polycarbonate and Aluminum bowls with a selection of sight gauge materials that meet
industry and application requirements
• Key lockable and tamper proof models
• Air purity class according to ISO 8573-1: 2010
Air Purity Class - ISO 8573-1: 2010*
5 μm (5:8:4)
25 μm (6:8:4)
40 μm (7:8:4)
* Maximum flow at 91.4 PSI (6.3 bar) inlet pressure to maintain
air purity class is 20.0 SCFM (566 L/min)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
17
SERIES
652
How to Order
Particulate Filter/Regulator
* Conforms to ISO standards 1179-1
** Compressed air must be dry enough so no ice formation is present on the
product. All bowls should be emptied prior to ambient temperatures dropping
below 32°F (0°C)
*** If multiple options are required, please use the on-line CAD configurator on
the website to generate the part number (www.numatics.com), or consult
factory.
8 652 A P B P 4 F A00 G N
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
P = Filter/Regulator - Particulate
Gauge Type
B = Digital Pressure Switch - PNP
C = Digital Pressure Switch - NPN
D = Digital Gauge
F = Low Profile Gauge PSI/bar
G = Low Profile Gauge bar/PSI
H = Low Profile Gauge PSI/bar with Pressure Range Indicator
J = Low Profile Gauge bar/PSI with Pressure Range Indicator
N = No Gauge with Port Plate (1/8 NPTF)
P = No Gauge with Port Plate (1/8 ISO 7/1 Rc)
Q = Round Gauge bar/PSI
R = Round Gauge PSI/bar
0 = No Gauge Port
Options***
A00 = No Options
101 = Side Mounting Brackets
102 = Panel Nut
103 = Tamper Resistant
104 = Key Lockable
105 = High Temperature (80°C/176°F)
106 = Low Temperature (-40°C/-40°F)***
109 = FKM Seals
113 = Stainless Steel Fasteners
114 = Provision for Key Lockable Option
117 = ATEX Zones 1-21
119 = Panel Bracket with Panel Nut
121 = Non-Relieving
123 = Gauge Type Mounted for
Right-to-Left Flow
202 = 105 + 109
2A9 = 105 + 106
Pressure Range
D = 3-45 PSIG / 0.2-3 bar
E = 3-60 PSIG / 0.2-4 bar
G = 7-125 PSIG / 0.5-8 bar
H = 7-145 PSIG / 0.5-10 bar
B/C
N/P
F/G
0
D
Q/R
H/J
101 104103
123
119
Elements
A = 40 Micron
B = 5 Micron
J = 25 Micron
A JB
Bowl Type
K = Metal Bowl without Sight Gauge
L = Metal Bowl with Sight Gauge (Glass)
M = Metal Bowl with Sight Gauge (Polyamide)
P = Polycarbonate Bowl with Bowl Guard
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
Drain Type
0 = No Drain
A = Auto Drain Normally Open
N = Manual - Semi-Automatic Drain
Q = Manual Drain - Stainless Steel
A QN
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
18
SERIES
652
Dimensional Drawing - 652 Series Particulate Filter/Regulator
Cross Section - 652 Series
Particulate Filter/Regulator
Dimensions: mm (Inches)
A B C D E F G H J K L
248 94.5 66 33 69 30.5 4 160 25 41.75 42
(9.76) (3.72) (2.60) (1.30) (2.72) (1.20) (0.16) (6.30) (0.98) (1.64) (1.65)
M N P Q R S T V W ØX ØY
50 20 10 61.5 84 105.5 29 14.5 6.3 7 11
(1.97) (0.79) (0.39) (2.42) (3.30) (4.15) (1.14) (0.57) (0.25) (0.28) (0.43)
* Variable dimension based on type of drain that is specified; If an Automatic Drain is specified, add another 5 mm to
"J" dimension, which also adds 5 mm to the "A" dimension.
H*
12
To remove bowl allow 75 mm
(2.95in) from the bottom of the
bowl drain.
B
E
F
C
D
L
M
K
N
P
W
Q
R
S
ØX
T
V
A*
J*
G
ØY
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
19
SERIES
652
H*
12
• Extensive range of coalescing filter elements to remove oil and sub-micron particles
down to 0.01 microns. Air purity class according to ISO 8573-1: 2010
• Optional 3 micron pre-filter integrated in the coalescing element eliminates the need
for a separate particulate element.
• Optional low profile gauge, round gauge, digital gauge or digital pressure switch
• Optional extended temperature range up to 176°F (80°C)
• Threaded ports allow for individual or modular mounting
• Innovative two position plastic drain with manual and semi-automatic functions
Additional drains include an automatic style (brass) and manual (stainless steel)
• Polycarbonate and Aluminum bowls with a selection of sight gauge materials that
meet industry and application requirements
• Key lockable and tamper proof models
Performance Data
Port Sizes 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow - Per ISO 6358
P1 = 91.4 PSI (6.3 bar)
∆P = 5 PSI (0.35 bar)
Micron Rating SCFM (L/min ANR)
1/4
0.3 μm 40.3 (1150)
0.01 μm 36.8 (1050)
3/8
0.3 μm 40.5 (1155)
0.01 μm 36.9 (1055)
1/2
0.3 μm 420 (1200)
0.01 μm 39.0 (1114)
Maximum /Inlet Pressure PSIG (bar) P1
Polycarbonate Bowl 232 (16)
Aluminum Bowl 232 (16)
Adjustable Pressure Ranges PSIG (bar)
3 to 45 (0.2 to 3)
3 to 60 (0.2 to 4)
7 to 125 (0.5 to 8)
7 to 145 (0.5 to 10)
Ambient Temperature Range °F (°C) 35 to 122 (1.7 to 50)
Fluid Temperature Range °F (°C) 35 to 122 (1.7 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg)
Polycarbonate Bowl 1.24 (0.564)
Aluminum Bowl 1.55 (0.705)
COALESCING FILTER/REGULATOR
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Springs Stainless Steel
Filter Element Borosilicate Microfiber & Polyester
Filter Element End Cap Polypropylene
Bowl Polycarbonate or Aluminum
Air Purity Class - ISO 8573-1: 2010*
0.3 μm (3:7:3)
0.01 μm (2:7:2)
* Maximum flow at 91.4 PSI (6.3 bar) inlet pressure to maintain
stated air purity class is 10.6 SCFM (303 L/min)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
20
SERIES
652
How to Order
Coalescing Filter/Regulator
* Conforms to ISO standards 1179-1
** If multiple options are required, please use the on-line CAD configurator on
the website to generate the part number (www.numatics.com), or consult
factory.
8 652 A C D P 4 F A00 G N
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
C = Filter/Regulator - Coalescing
Gauge Type
B = Digital Pressure Switch - PNP
C = Digital Pressure Switch - NPN
D = Digital Gauge
F = Low Profile Gauge PSI/bar
G = Low Profile Gauge bar/PSI
H = Low Profile Gauge PSI/bar with Pressure Range Indicator
J = Low Profile Gauge bar/PSI with Pressure Range Indicator
N = No Gauge with Port Plate (1/8 NPTF)
P = No Gauge with Port Plate (1/8 ISO 7/1 Rc)
Q = Round Gauge bar/PSI
R = Round Gauge PSI/bar
0 = No Gauge Port
Options**
A00 = No Options
101 = Side Mounting Brackets
102 = Panel Nut
103 = Tamper Resistant
104 = Key Lockable
105 = High Temperature (80°C/176°F)
109 = FKM Seals
113 = Stainless Steel Fasteners
114 = Provision for Key Lockable Option
117 = ATEX Zones 1-21
119 = Panel Bracket with Panel Nut
121 = Non-Relieving
123 = Gauge Type Mounted for
Right-to-Left Flow
202 = 105 + 109
Pressure Range
D = 3-45 PSIG / 0.2-3 bar
E = 3-60 PSIG / 0.2-4 bar
G = 7-125 PSIG / 0.5-8 bar
H = 7-145 PSIG / 0.5-10 bar
B/C
N/P
F/G
0
D
Q/R
H/J
101 104103
123
119
Bowl Type
K = Metal Bowl without Sight Gauge
L = Metal Bowl with Sight Gauge (Glass)
M = Metal Bowl with Sight Gauge (Polyamide)
P = Polycarbonate Bowl with Bowl Guard
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
Drain Type
0 = No Drain
A = Auto Drain Normally Open
N = Manual - Semi-Automatic Drain
Q = Manual Drain - Stainless Steel
A QN
Elements
D = 0.3 Micron - Coalescer
E = 0.01 Micron - Coalescer
M = 0.3 Micron Coalescer with 3 Micron Prefilter
N = 0.01 Micron Coalescer with 3 Micron Prefilter
D/M E/N
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
21
SERIES
652
Dimensional Drawing - 652 Series Coalescing Filter/Regulator
Cross Section - 652 Series
Coalescing Filter/Regulator
Dimensions: mm (Inches)
A B C D E F G H J
248 94.5 66 33 69 30.5 2.5 135 25
(9.76) (3.72) (2.60) (1.30) (2.72) (1.20) (0.10) (5.31) (0.98)
* Variable dimension based on type of drain that is specified; If an Automatic Drain is specified,
add another 5 mm to "J" dimension, which also adds 5 mm to the "A" dimension.
H*
12
To remove bowl allow 80 mm
(3.1in) from the bottom of the
bowl drain.
A*
B
C
D
E
F
J*
G
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
22
SERIES
652
Performance Data
Port Sizes 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow - Per ISO 6358
P1 = 91.4 PSI (6.3 bar)
∆P = 11.6 PSI (0.8 bar)
SCFM (L/min ANR)
1/4 97.3 (2780)
3/8 175.0 (5000)
1/2 178.5 (5100)
Maximum Pressure PSIG (bar)
Polycarbonate Bowl 145 (10)
Aluminum Bowl 145 (10)
Minimum Flow for Lubrication - SCFM (L/min) 0.7 (20)
Ambient Temperature Range °F (°C) 41 to 122 (5 to 50)
Fluid Temperature Range °F (°C) 41 to 122 (5 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg)
Polycarbonate Bowl 1.16 (0.526)
Aluminum Bowl 1.47 (0.667)
• Provides consistent reliable lubrication to the system
• Uses venturi type technology to distribute the lubrication into the
compressed air line
• Lubrication begins at 0.7 SCFM (20 L/Min ANR)
• Optional electronic liquid level indicator provides condition monitoring
• Polycarbonate and Aluminum bowls with a selection of sight gauge
materials that meet industry and application requirements
• Recommended oil type: Non-detergent type and without aggressive
additives (VG32 - ISO3448)
• Threaded ports allow for individual or modular mounting
• Oil capacity (bowl): 4.39 in³ (72 cm³)
LUBRICATOR
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
23
SERIES
652
How to Order
Lubricator
* Conforms to ISO standards 1179-1
** If multiple options are required, please use the on-line CAD configurator on the
website to generate the part number (www.numatics.com), or consult factory.
8 652 A L 0 P 4 0 A00 0 0
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
L = Lubricator
Bowl Type
K = Metal Bowl without Sight Gauge
L = Metal Bowl with Sight Gauge (Glass)
M = Metal Bowl with Sight Gauge (Polyamide)
P = Polycarbonate Bowl with Bowl Guard
Options**
A00 = No Options
101 = Side Mounting Brackets
108 = Liquid Level Indicator - Electronic
109 = FKM Seals
113 = Stainless Steel Fasteners
117 = ATEX Zones 1-21
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
K/L/M
101
P
108
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
24
SERIES
652
Dimensional Drawing - 652 Series Lubricator
Cross Section - 652 Series
Lubricator
Dimensions: mm (Inches)
A B C D E F G
217 64 66 33 69 30.5 135
(8.54) (2.52) (2.60) (1.30) (2.72) (1.20) (5.30)
A
B
C
E
D
F
To remove bowl allow 25 mm
(1.0in) from the bottom of the
bowl.
G
12
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
25
SERIES
652
• Robust and easy-to-operate shut-off valve, with lockout (front or back)
on handle
• Provides shut-off to downstream machinery
• Optional low profile gauge provides clear indication of the downstream
pressure, and when the downstream components can be safely
removed when pressure (P2) is at zero
• Available as 3/2 or 2/2 construction
• Threaded ports allow for individual or modular mounting
SHUT-OFF ISOLATION VALVE
Materials in Contact with Fluid
Body Aluminum
Ball Zinc Plated Steel
Seat PTFE
Seals NBR/FKM
Performance Data
Port Sizes 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow - Per ISO 6358
P1 = 91.4 PSI (6.3 bar)
∆P = 14.5 PSI (1 bar)
SCFM (L/min ANR)
1 2 2 3
1/4 151 (4300) 8.05 (230)
3/8 308 (8800) 8.05 (230)
1/2 400 (11400) 8.05 (230)
Maximum Inlet Pressure PSIG (bar) 232 (16)
Ambient Temperature Range °F (°C) 14 to 122 (-10 to 50)
Fluid Temperature Range °F (°C) 14 to 122 (-10 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg) 0.97 (0.438)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
26
SERIES
652
How to Order
Shut-Off Isolation Valve
* Conforms to ISO standards 1179-1
** If multiple options are required, please use the on-line CAD configurator on
the website to generate the part number (www.numatics.com), or consult
factory.
8 652 A 3 M 0 4 F A00 00
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
2 = 2/2 - Shut Off Valve
3 = 3/2 - Shut Off Valve
Valve Type
M = Manually Operated Ball Valve with Lockout
Pilot Valve/Electrical Connection
0 = No Electrical Connection
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
Options**
A00 = No Options
101 = Side Mounting Brackets
109 = FKM Seals
111 = Metal Muffler
112 = Polyethylene Muffler
113 = Stainless Steel Fasteners
115 = Scissor Lock
117 = ATEX Zones 1-21
122 = Bottom Oriented Pressure Adjustment
123 = Gauge Type Mounted for
Right-to-Left Flow
2B9 = 111 + 115
101
122 123
Gauge Type
F = Low Profile Gauge PSI/bar
G = Low Profile Gauge bar/PSI
H = Low Profile Gauge PSI/bar with
Pressure Range Indicator
J = Low Profile Gauge bar/PSI with
Pressure Range Indicator
N = No Gauge with Port Plate (1/8 NPTF)
P = No Gauge with Port Plate (1/8 ISO 7/1 Rc)
Q = Round Gauge bar/PSI
R = Round Gauge PSI/bar
0 = No Gauge Port
N/P
F/G
0Q/R
H/J
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
27
SERIES
652
Dimensional Drawing - 652 Series Shut-Off Isolation Valve
Cross Section - 652 Series
Shut-Off Isolation Valve
Dimensions: mm (Inches)
A B C D E F G H J K L M
99 68 66 33 69 34.5 2.5 58 29 35 39 9
(3.90) (2.68) (2.60) (1.30) (2.72) (1.36) (0.10) (2.28) (1.14) (1.38) (1.54) (0.35)
12
E
F
A
C
D
G
K
B
H
J
L
M
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
28
SERIES
652
• High exhaust capacity for quick depletion of downstream pressure
• Slow Starts provide gradual increase of downstream pressure and full flow
once 70% of inlet pressure is reached
• Threaded ports allow for individual or modular mounting
• Manual override (momentary-pulse type) is standard when using the
horizontal solenoid operator
• Optional extended temperature range of -40°F to 176°F (-40°C to 80°C); for
air piloted models only (excludes solenoid operators)
• Constructions includes: 3/2 Quick Exhaust, 3/2 Slow-Start/Quick-Exhaust,
and 2/2 Slow Start
• Electrical connections: Coil with DIN terminals; DIN Plug, DIN Plug with LED,
and coil with built-in M12 3 Pin male connection (24 VDC)
• Voltages: 24 VDC, 115-50/60 VAC, 230-50/60 VAC, 24-50/60 VAC
Performance Data
Port Sizes 1/4, 3/8, 1/2
Thread Type NPTF, G & Rc
Nominal Flow – Per ISO 6358
P1 = 91.4 PSI (6.3 bar)
∆P = 14.5 PSI (1 bar)
SCFM (L/min ANR)
1 2 2 3
1/4
53 (1500) 74 (2100)
3/8
132 (3750) 151 (4300)
1/2
164 (4650) 176 (5000)
Minimum Operating Pressure PSIG (bar) 40 (2.75)
Maximum Operating Pressure PSIG (bar) 145 (10)
Ambient Temperature Range °F (°C) 14 to 122 (-10 to 50)
Fluid Temperature Range °F (°C) 14 to 122 (-10 to 50)
Fluid Air or Inert Gas
Weight Ibs. (kg)
1.46 (0.661)
Operating Data
24/DC 120/60 240/60 24/60
Power — 9 VA 9 VA 9 VA
Holding 3.0 Watts 4 VA (3.0 Watts)
SLOW-START/QUICK EXHAUST VALVE
Materials in Contact with Fluid
Body Aluminum
Seals NBR/FKM
Springs Stainless Steel
Response Time (ms)
Energized De-Energized Voltage
17 40 24/DC
11 34 24, 115 & 230-50/60 VAC
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
29
SERIES
652
How to Order
Slow-Start/Quick Exhaust Valve
* Conforms to ISO standards 1179-1
** Available for 24 VDC voltage only
*** If multiple options are required, please use the on-line CAD configurator on the
website to generate the part number (www.numatics.com), or consult factory.
**** Option 117 (ATEX 1-21) is available with Valve Type "E" or "P". For Valve
Type "S" (Solenoid Pilot), please select "9" under the "Pilot Valve/Electrical
Connection. Consult factory for further information.
8 652 A 6 S 6 4 F A00 F1
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
4 = 2/2 - Slow Start
5 = 3/2 - Quick Exhaust
6 = 3/2 - Slow Start/Quick Exhaust
Valve Type
E = External Air Pilot
P = Internal Air Pilot (Available on 2/2 Slow
Start only)
S = Solenoid Pilot
Pilot Valve/Electrical Connection
0 = No Electrical Connection
1 = Vertical Solenoid, without DIN Connector
(must order with option 110)
2 = Vertical Solenoid. DIN Connector with LED
(must order with option 110)
3 = Vertical Solenoid, DIN Connector w/o LED
(must order with option 110)
4 = Vertical Solenoid, 3 Pin M12 Connection**
(must order with option 110)
5 = Horizontal Solenoid, without DIN Connector
6 = Horizontal Solenoid, DIN Connector with LED
7 = Horizontal Solenoid, DIN Connector without LED
8 = Horizontal Solenoid with 3 Pin M12 Connection**
9 = Without Pilot Operator
Port Size
2 = 1/4
3 = 3/8
4 = 1/2
Options***
A00 = No Options
101 = Side Mounting Brackets
109 = FKM Seals
110 = Without Manual Override
111 = Metal Muffler
112 = Polyethylene Muffler
113 = Stainless Steel Fasteners
117 = ATEX Zones 1-21 ****
123 = Gauge Type Mounted for
Right-to-Left Flow
201 = 110 + 111
Voltage
F0 = 115 50/60 VAC
F1 = 24 VDC
F4 = 24 50/60 VAC
F6 = 230 50/60 VAC
00 = No Voltage
101
123
Gauge Type
B = Digital Pressure Switch - PNP
C = Digital Pressure Switch - NPN
D = Digital Gauge
F = Low Profile Gauge PSI/bar
G = Low Profile Gauge bar/PSI
H = Low Profile Gauge PSI/bar with
Pressure Range Indicator
J = Low Profile Gauge bar/PSI with
Pressure Range Indicator
N = No Gauge with Port Plate (1/8 NPTF)
P = No Gauge with Port Plate (1/8 ISO 7/1 Rc)
Q = Round Gauge bar/PSI
R = Round Gauge PSI/bar
0 = No Gauge Port
B/C
N/P
F/G
0
D
Q/R
H/J
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
30
SERIES
652
Dimensional Drawing - 652 Series Slow-Start/Quick Exhaust Valve
Cross Section - 652 Series
Slow-Start/Quick
Exhaust Valve
Dimensions: mm (Inches)
A B C D E F G H J
193 127 66 33 69 30.5 76 110.5 57
(7.60) (5.00) (2.60) (1.30) (2.72) (1.20) (3.00) (4.35) (2.24)
12
3
B
A
C
E
F
G
H
J
D
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
31
SERIES
652
• Ideal for branching off primary 652 series air prep manifold to add
additional products, such as adding another regulator or dividing
lubricated and un-lubricated compressed air lines
• 1/8 or pad mount interface ports on top of product for adding pressure
switches/sensors or other condition monitoring devices
• 3/8 ports on the front and back provide additional flexibility to attach or
branch off the main manifold. It can also be used to feed auxiliary air to
air prep assemblies that require additional air capacity, such as a bank
of manifold regulators
Performance Data
Port Sizes
Left, Right & Bottom 1/2 & Flanged
Front & Back 3/8
Thread Type NPTF, G & Rc
Top Port (for Pressure Switch/Pressure Sensor) 1/8 NPTF
Maximum Pressure PSIG (bar) 232 (16)
Fluid Air or Inert Gas
Weight Ibs. (kg) 0.73 (0.331)
DIVERTER BLOCK
Materials in Contact with Fluid
Body Aluminum
How to Order
Diverter Block
8 652 A D 0 0 4 T A00 0 0
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
D = Diverter Block
Options**
A00 = No Options
101 = Side Mounting Brackets
117 = ATEX Zones 1-21
Port Size
4 = 1/2
Pressure Switch Interface
C = Pad Mount (Europe only)
T = 1/8 (US only)
* Conforms to ISO standards 1179-1
** If multiple options are required, please use the on-line CAD configurator on the website to generate the part number (www.numatics.com), or consult factory.
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
32
SERIES
652
Dimensional Drawing - 652 Series Diverter Block
Cross Section - 652 Series
Diverter Block
Dimensions: mm (Inches)
A B C D E F G H
66.5 30.5 66 33 70 35 10 20
(2.62) (1.20) (2.60) (1.30) (2.76) (1.38) (0.39) (0.79)
12
2
A
B
C
E
F
D
1/8 NPTF
E
F
H
G
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
33
SERIES
652
• Modular assembly to 652 series manifold using common 652 series
body-to-body clamps
• Provides high exhaust capacity of downstream pressure
• Available as full-flow start or slow-start
• Slow-start feature allows operator to turn knob counter clock wise to
“On” position, gradually ramping up downstream pressure
• Bright yellow body with red knob is easily identified as an emergency
shut-off device
• Typically located as the final component in an Air Preparation assembly
Performance Data
Port Sizes* 1/2
Nominal Flow
1 2 2 3
SCFM (L/min ANR) 116 (5905) 116 (5905)
Ambient Temperature Range °F (°C) 40 to 120 (4 to 50)
Fluid Temperature Range °F (°C) 40 to 120 (4 to 50)
Maximum Pressure PSIG (bar) 150 (10.3)
Fluid Air or Inert Gas
Weight Ibs. (kg)
Standard 2.7 (1.23)
Slow Start 3.1 (1.39)
* Ports are not threaded (grey flanges). Easily connect to 652 Series Manifold. When connecting to pipe, use end-
plate kits #T652AT502468001
LOCKOUT VALVE
Materials in Contact with Fluid
Body Aluminum
Seals NBR
Spool Aluminum
3/2 Lockout Valve with
Slow Start Feature
3/2 Lockout Valve
How to Order
Lockout Valve
T 652 A 5 L 0 4 0 A00 00
Port Type
T = Modular Mounting
Product Series
652
Revision
A
Product Type
5 = 3/2 - Quick Exhaust
6 = 3/2 - Slow Start - Quick Exhaust
Options*
A00 = No Option
111 = Metal Muffler
115 = Scissor Lock
2B9 = 111 + 115
Port Size
1/2
Valve Type
L = Manually Operated Lockout
* If multiple options are required, please use the on-line CAD configurator on the website to generate the part number (www.numatics.com), or consult factory.
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
34
SERIES
652
Dimensional Drawing - 652 Series Lockout Valve
Dimensions: mm (Inches)
G
E
F
H
J
B
A
K
D
C
G
E
F
A
B
K
H
J
D
C
A B C D E
237.5 164.9 126.2 63.1 76.2
(9.35) (6.49) (4.96) (2.48) (3.00)
F G H J K
38.1 42.7 62.2 31.1 25.4
(1.50) (1.68) (2.44) (1.22) (1.00)
3/2 Lockout Valve
A B C D E
204 131.3 126.2 63.1 76.2
(8.03) (5.17) (4.96) (2.48) (3.00)
F G H J K
38.1 119 62.2 31.1 25.4
(1.50) (4.68) (2.44) (1.22) (1.00)
12
3
12
3
3/2 Lockout Valve Cross Section
3/2 Lockout Valve with Slow
Start Feature Cross Section
3/2 Lockout Valve with Slow Start Feature
Note: When the knob is pushed down (Closed position), the lockout shaft extends out of the bottom by 12.2 mm (0.48 inches). The lockout hole
diameter in the shaft is 11.2 mm (0.44 inches). These measurements are the same for the standard Lockout and the Slow-Start version.
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
35
SERIES
652
AIR PREPARATION MANIFOLD ASSEMBLIES
How to Order
Air Preparation Manifold Assemblies
All manifolds come assembled and fully tested to your configuration.
If additional support is required in the middle of a manifold. Please specify kit number P699AT502467001. This kit
contains one Wall/Panel Bracket (also referred to as support bracket or mounting bracket). This bracket can be
installed at the factory or ordered separately as a kit. This kit contains two screws, which allows customers to easily
attach the bracket to the back of any of the body-to-body clamps in the manifold assembly.
After selecting the top level assembly part number, please refer to each of the How-to-Order charts within this catalog
to determine the specific product that is required in the manifold assembly. The How-to-Order charts are located on
the following pages:
Particulate Filter: Page 5
Coalescing Filter: Page 8
Regulator: Page 11
Manifold Regulator: Page 14
Particulate Filter/Regulator: Page 17
Coalescing Filter/Regulator: Page 20
Lubricator: Page 23
Shut-Off Isolation Valve: Page 26
Slow Start/Quick Exhaust Valve: Page 29
Diverter Block: Page 31
Lockout Valve: Page 33
* Conforms to ISO standards 1179-1
8 652 A S L D 4 C 0 0 A00
Port Type
8 = NPTF
G = ISO 228/1-G*
J = ISO 7/1 Rc
Product Series
652
Revision
A
Product Type
S = FRL Assembly
Air Flow Direction
L = Configure Air Flow P(1) Left - P(2) Right
R = Configure Air Flow P(1) Right - P(2) Left
Number of Stations
A = 1 K = 11
B = 2 L = 12
C = 3 M = 13
D = 4 N = 14
E = 5 O = 15
F = 6 P = 16
G = 7 Q = 17
H = 8 R = 18
I = 9 S = 19
J = 10 T = 20
Options
A00 = No Options
117 = ATEX Zones 1-21
End Plate Port Size
0 = None
4 = 1/2
Mounting Type
0 = No Mounting
C = End Plates, Body-to-Body Assembly
Clamps & Wall/Panel Brackets
F = End Plates and Body-to-Body
Assembly Clamps
L = Side Mounting Brackets
C LF
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
36
SERIES
652
Example #2
The following example assembly includes five stations of the 652 series products and side mounting brackets. The
manifold air flow is from Right-to-Left. Port type is ISO 228/1-G. Port size is 3/8.
The Lubricator is configured with an Electronic Liquid Level Indicator (option 108). The Shut-off Isolation Valve uses a
combination option (270), which is configured when you use a Metal Muffler (111) and a low profile gauge that requires
a right-to-left flow (123). The Coalescing Filter/Regulator also uses a combination option. In this case a combination
option (243) includes a Key Lockable Handle (104) and a low provide gauge that requires right-to-left flow (123).
How-to-order 652 Series Air Preparation Manifold Assemblies (Examples)
Example #1
The following example assembly includes six stations of the 652 series products, manifold end plates with mounting
brackets and an additional support bracket between station 1 and 2. The manifold air flow is from Left-to-Right. Port
type is NPTF. Port size is 1/2.
The regulator is configured for a bottom oriented pressure adjustment (option 122). The Shut-Off Isolation Valve is
configured with a low profile gauge, with pressure range indicators.
Example Order
Assembly 8652ASLF4C00A00 652 Series Air Prep Assembly
Station 1 8652A3M04H11100 652 Series Shut Off Isolation Valve
P699AT502467001 Support Bracket
Station 2 8652ABBP4JA000N 652 Series Particulate Filter
Station 3 8652AFDM4FA000A 652 Series Coalescing Filter
Station 4 8652AR004F122G0 652 Series Regulator
Station 5 8652AD004TA0000 652 Series Diverter Block
Station 6 8652A6S74FA00F1
652 Series Slow-Start/Quick
Exhaust Solenoid Valve
Example Order
Assembly G652ASRE0L00A00 652 Series Air Prep Assembly
Station 5 G652AL0M3010800 652 Series Lubricator
Station 4 G652AD004TA0000 652 Series Diverter Block
Station 3 G652ACDM3F243GA 652 Series Coalescing Filter-Regulator
Station 2 G652ABBM3JA000A 652 Series Particulate Filter
Station 1 G652A3M03F27000 652 Series Shut Off Isolation Valve
Assembled
Assembled
If multiple options are required, please use the on-line CAD configurator on the
website to generate the part number (www.numatics.com), or consult factory.
1
1
2
2
3
3
4
4
5
5
6
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
37
SERIES
652
Dimensions: mm (Inches)
Dimensional Drawings - Mounting Options
Side Mounting Brackets Kit#: P652AT50386002
B
C
D
A
E
ØH
F
G
Wall/Panel Bracket Kit#: P699AT502467001
A B C D E F G ØH
25
(0.98)
11
(0.43)
20
(0.79)
10
(0.39)
6.3
(0.25)
50
(1.97)
1.9
(0.075)
11
(0.43)
A B C D
26
(1.02)
13
(0.51)
92
(3.62)
46
(1.81)
E F G ØH
6
(0.24)
3
(0.12)
6.5
(0.26)
6.5
(0.26)
J K L M
8
(0.31)
18
(0.71)
109
(4.29)
44.5
(1.75)
A
B
K
J
C
D
ØH
E
F
G
L
M
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
38
SERIES
652
Dimensions: mm (Inches)
A
B
Drain Port: 1/8
ISO 228/1-G
A
C
Drain Port: 10-32 UNF
A
D
Drain Port: 1/8
ISO 228/1-G
A B C D
135
(5.3)
25
(0.98)
22.3
(0.88)
30
(1.18)
Polycarbonate Bowl/Guard with
Semi-Automatic/Manual Drain
Polycarbonate Bowl/Guard with
Stainless Steel Manual Drain
Metal Bowl with
Automatic Drain
Dimensional Drawings - Bowl and Drain Options
Note: For Filters and Filter-Regulators, allow for at least 85 mm (3.3 inches) clearance for removal of bowl (if
using an automatics drain). For Lubricators (without the Electronic Liquid Level Indicator), allow for 25 mm (1.0
inches).
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
39
SERIES
652
280 Series Digital Pressure Switch
Performance Data
Port Size/Thread Type
1/8 NPTF Male x 10/32 UNF Female
1/8 ISO 7/1 Rc Male x M5-0.8 Female
Ambient Temperature Range °F (°C)
32 to 122 (0 to 50)
Rated Pressure Range PSIG (bar)
0 to 145 (0 to 10)
Maximum Pressure PSIG (bar)
217.5 (15)
Fluid
Air or Inert Gas
Set Pressure Resolution
kPa 1
kgf/cm² 0.01
bar 0.01
PSI 0.1
LCD Display
7 Segment; Red/Green Color
Sampling Rate
5 times per second
Repeatability
≤ +/- 0.2% F.S. +/- 1 Digit
Hysteresis (window comparator mode)
Adjustable
Electrical Ratings
Power Supply Voltage
12 to 24 VDC +/- 10% Ripple (P-P) 10% or Less
Current Consumption
≤ 45 mA (with no load)
Switch Output
PNP Open Collector / NPN Open Collector
Max. Load Current
125 mA 125 mA
Max Supply Voltage
24 VDC 30 VDC
Residual Voltage
≤ 1.5 V ≤ 1.5 V
Load Current
125 mA 125 mA
Enclosure Rating
IP40
Materials in Contact with Fluid
Enclosure Case
PBT + 30 GF
Port
Nickel Plated Brass
Seals
NBR
How to Order
Model Numbers
DPS280PNQ8 1/8 NPTF (PNP)
DPS280NNQ8 1/8 NPTF (NPN)
DPS280PRQ8 1/8 ISO 7/1 Rc (PNP)
DPS280NRQ8 1/8 ISO 7/1 Rc (NPN)
Model Accessory Description
DPS280-8-4-ST-2 Mating Cable 8 mm 4 Pin 2 Meter
DPS280-8-4-ST-5 Mating Cable 8 mm 4 Pin 5 Meter
PC0402MEETA03000 Patch Cable M8 4 Pin X M12 3 Pin 2 Meter
Model Accessory Description
PMK280-C Panel Mount Kit with Cover
Accessory Numbers
Display Panel Instructions
Switch Wiring
Output Circuit Wiring
Pressure Unit
Display Section
2 Colors Main Display
Setting Mode
Display Section
Button
Button
Set
Button
(Green)
Key Lock Indicator
Output Indicator
NPN outputPNP output
DC (+)(Brown)
OUT (Black)
DC (-)(Blue)
DC (+)(Brown)
OUT (Black)
DC (-)(Blue)
Switch main circuit
Switch main circuit
NPN output
PNP output
DC (+)(Brown)
OUT (Black)
DC (-)(Blue)
DC (+)(Brown)
OUT (Black)
DC (-)(Blue)
Switch main circuit
Switch main circuit
(1) Brown (+)
(2) White (NOT USED)
(3) Blue (-)
(4) Black (OUT)
2
4
13
PINOUT
MALE (switch end)
Note: All part numbers include an 8 mm Pico 4 Pin connector and 2 meter cable (4 mm O.D. x 26 AWG)
280 SERIES DIGITAL PRESSURE SWITCH
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
40
SERIES
652
To adjust, turn adjusting knob clockwise
to increase and counter-clockwise to
decrease set point
28.5 mm (1-1/8) Hex
1/8 NPTF or
G
77mm (3.0)
ø 30.55 mm (1.2)
Lumberg Connector (or equivalent)
Micro Style RSF4/0.5M
N.O. Pin 4
N.C. Pin 3
Com. Pin 1
M12 X 1
Thread
Dimensions: mm (Inches)
Dimensional Drawings - PS182 Pressure Switch
PS182 Series Pressure Switch
Performance Data
Port Size/Thread Type
1/8 NPTF or 1/8 ISO 228/1-G (BSPP)
Ambient Temperature Range °F (°C)
-40 to 250 (-40 to 121)
Set Point Adjustment Ranges PSI (bar)
2-10 (.14 to .69), 6-30 (.41 to 2.07), 20-130 (1.38 to 8.96)
Set Point Tolerance
+ 1 PSI or 5%
Maximum Pressure PSIG (bar)
600 (41.4)
Fluid
Air or Inert Gas
Maximum Cycle Rate per Minute
200
Hysteresis Adjustment
10%
Electrical Ratings
Switch Contact Rating
4 Amp (Gold Plated Contacts)
Voltage Range
12 VDC to 250 VDC
Enclosure Rating
IP 65
Electrical Connection
3 Pin M12
Materials in Contact with Fluid
Enclosure Case
Anodized Aluminum
Body
Brass
Seals
NBR
How to Order
Model Numbers
PS182CAN01 1/8 NPTF
PS182CAG01 1/8 ISO 228/1-G (BSPP)
PS182 SERIES PRESSURE SWITCH
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
41
SERIES
652
How to Order
Model Numbers
PS180CAN01 1/8 NPTF
PS180CAG01 1/8 ISO 228/1-G
How to Order
Model Numbers
M699AG50465001 1/8 NPTF
M699AG50465002 1/8 ISO 7/1 Rc
PS180 Series Pressure Switch
Performance Data
Port Size/Thread Type
1/8 NPTF & ISO 228/1-G (BSPP)
Ambient Temperature Range °F (°C)
0 to 190 (-15 to 85)
Set Point Adjustment Ranges PSI (bar)
4-20 (.28 to 1.38), 14-150 (.97 to 10.34)
Maximum Pressure PSIG (bar)
300 (20.7)
Fluid
Air or Inert Gas
Maximum Cycle Rate per Minute
200
Hysteresis Adjustment
15%
Electrical Ratings
Switch Contact Rating
4 Amp
Maximum Voltage
250 VAC (200 VDC)
Enclosure Rating
IP 65
Materials in Contact with Fluid
Connector Housing
Polyamide
Port
Zinc Plated Steel
Seals
NBR
Digital Pressure Gauge
Performance Data
Port Size/Thread Type
1/8 (NPTF or ISO 7/1 Rc)
Ambient Temperature Range °F (°C)
32 to 122 (0 to 50)
Rated Pressure Range PSIG (bar)
0 to 145 (0 to 10)
Maximum Pressure PSIG (bar)
217.5 (15)
Fluid
Air or Inert Gas
Display (Unit Measurement)
PSI, bar, Mpa, kgf/cm²
LCD Display
7 Segment 3-1/2 Digit
Sampling Rate
2 times per second
Repeatability
< + 0.2% + 1 Digit
Electrical Ratings
Battery
CR 2032 Lithium (Replaceable)
Battery Life
3 Year (display turned on 5 times per day)
Battery Power Saving Mode
Display turns off after 30 seconds
Enclosure Rating
IP65
Materials in Contact with Fluid
Enclosure - Front Case
ABS
Enclosure - Back Case
Zinc
Seals
NBR
PS180 SERIES PRESSURE SWITCH/
DIGITAL PRESSURE GAUGE
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
42
SERIES
652
349 SERIES PRESSURE SWITCH
349 Series Pressure Switch
Performance Data
Without Protection With Protection
Port Size/Thread Type
Pad Mounted
Fluid
Air or Inert Gas
Pressure Setting
0.2 to 6, 0.5 to 10, 0.5 to 16 bar
Hysteresis
0.4 bar at the beginning of adjustment range
1 bar at the end of adjustment range
Operating Temperature (°C)
-10 to +60 0 to +60
Max Voltage
250V - AC/DC 24 VDC
Current Breaking Capacity
5A - 250V resistive 2A - 24Vcc Resistive
Protection Degree
IP65
Max Speed
60 cycles per minute
Material in contact with fluid
Body
High Performance Polymer(PA61/XT) / Aluminium for 16 bar version
Seals
NBR
How to Order
0.2 - 6 bar 0.5 - 10 bar 0.5 - 16 bar
With Protection
34900028 34900031 34900034
Without Protection
34900027 34900030 34900033
Dimensional Drawings
With Protection Electrical Diagram
Electrical Connection
With and Without Protection
Without Protection
With Protection
1 Pressure set screw (spanner
for hexagon nuts: 3 mm)
2 2 holes Ø 5,5 for mounting
3 ISO4400 size 30 connector,
4 terminals, rotatable by 90°
Status indicated by two diodes:
• at rest: contact 1-2 made: orange diode lights
• at work: contact 1-3 made: red diode lights
Terminal connection for 1,5 mm
2
wire integrated
interference blinking
1 Pressure set screw (spanner
for hexagon nuts: 3 mm)
2 2 holes Ø 5,5 for mounting
3 Identification label holder
4 Pg9P connector, non rotatable*
62
**
2
X
Ø 5,5
30
81
*
20
16
2
3
1
Ø 8
30
4
Ø 8
62
**
2 X Ø 5,5
30
79
*
20
16
1
2
30
3
24V
A1
A2
R
0V
PE
P
Connector
Pressure Switch
(1
)
(3)
(2)
(4)
1
3
2
}
}
Terminal
Connector
Terminal
Pressure Switch
P
23
1
2
1
3
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
43
SERIES
652
Electric Differential Pressure Indicator
Performance Data
Ambient Temperature Range °F (°C)
-13 to 212 (-25 to 100)
Maximum Pressure PSIG (bar)
290 (20)
Delta P Setting +PSIG (bar)
10.2 (0.7)
Electrical Ratings
Switching Contact
SPDT
14 VDC/5 A; 30 VDC/4 A; 125 VAC/5 A; 250 VAC/5 A
Minimum Load
5 VDC / 160 mA
Enclosure Rating
IP65 (DIN Connector 43650)
Materials in Contact with Fluid
Body
Brass
Seals
NBR
How to Order
Model Numbers
M699AG439851003
How to Order
Model Numbers
M699AG506837001
Electronic Liquid Level Indicator (for Lubricator)
Performance Data
Actuation Point
25 mL (Nominal)*
Switch Contact is open when fluid drops below 25 mL
Connection
1/8-27 NPT External Thread
Electrical Ratings
Switching Contact
SPST
Switch Type
50 Watt Reed Switch
Wire Size / Length
22 AWG / 24 Inches (610 mm)
Materials in Contact with Fluid
Body
Brass
Float
Nylon
ELECTRIC DIFFERENTIAL PRESSURE INDICATOR/
ELECTRONIC LIQUID LEVEL INDICATOR
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
44
SERIES
652
Repair Kits and Service Parts
652 Series - Spare Parts Kits
Description Kit Number
Bowls*
Polycarbonate Bowl & Bowl Guard - Includes NBR Bowl Seal for Filters,
Filter-Regulators and Lubricators (Electronic Liquid Level Indicator only)
M652AU440511001
Polycarbonate Bowl & Bowl Guard - Includes NBR Bowl Seal for Lubricators. M652AU440511008
Metal bowl without sight gauge. Includes NBR Bowl Seal. M652AU440511002
Metal bowl without sight gauge. Includes FKM Bowl Seal. M652AU440511011
Metal bowl with polyamide sight gauge. Includes NBR Bowl Seal. M652AU440511003
Metal bowl with polyamide sight gauge. Includes FKM Bowl Seal. M652AU440511013
Metal bowl with borosilicate (glass) sight gauge. Includes NBR Bowl Seal. M652AU440511004
Metal bowl with borosilicate (glass) sight gauge. Includes FKM Bowl Seal M652AU440511015
Drains
Drain Plug Assembly. Provides an option to customers that do not want to use a
bowl drain. Includes NBR seal.
M699AQ440512001
Semi-Automatic/Manual Drain Assembly - with NBR seals. This normally open drain
can be used as a manual drain or set to semi-automatic, which will drain the bowl
upon a loss of system pressure. Drain material is plastic.
M699AQ440512002
Semi-Automatic/Manual Drain Assembly - with FKM seals. This normally open drain
can be used as a manual drain or set to semi-automatic, which will drain the bowl
upon a loss of system pressure. Drain material is plastic.
M699AQ440512007
Manual Stainless Steel Drain Assembly - with NBR seals. Provides the user with an
alternative to the plastic semi-automatic drain.
M699AQ440512003
Manual Stainless Steel Drain Assembly - with FKM seals. Provides the user with an
alternative to the plastic semi-automatic drain.
M699AQ440512008
Automatic Drain Assembly - with NBR seals. This drain uses a float that initiates the
bowl to drain when the liquid rises. In addition, all fluid will drain when the pressure
drops below 22 PSI. Drain material is brass. This drain can also be operated manually.
M699AQ501862001
Bowl & Drain
Assembly
Bowl and Drain Assembly - Includes Polycarbonate Bowl/Guard and Semi-Automatic
Drain Assembly (NBR Seals).
M652AU513311001
* For lubricator replacement metal bowls, please also order bowl plug p/n M699AQ440512001. This is not required if the Electronic Liquid Level Indicator is used.
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
45
SERIES
652
Repair Kits and Service Parts
652 Series - Spare Parts Kits
Description Kit Number Color
Filter Elements
5 Micron Particulate Filter Element M652AE433582001 White
25 Micron Particulate Filter Element M652AE433582002 Yellow
40 Micron Particulate Filter Element M652AE433582003 Green
0.3 Micron Coalescing Filter Element EKF22D Green
0.01 Micron Coalescing Filter Element EKF22E Red
0.3 Micron Coalescing Filter Element - with 3 Micron pre-filter EKF22DD Green
0.01 Micron Coalescing Filter Element - with 3 Micron pre-filter EKF22ED Red
Adsorber (Activated Carbon) Filter EKF22F White/Clear
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
46
SERIES
652
Assembly and Mounting Kits
652 Series - Air Prep Assembly and Mounting Kits
Description Kit Number
Body-to-Body Assembly Clamps (Includes NBR O-Ring) Clamp material is
aluminum
P652AT502466001
Body-to-Body Assembly Clamps (Include FKM O-Ring)
Clamp material is aluminum
P652AT502466003
End Plate Kit (1/2 NPTF): Includes two end plates and body-to-body assembly
clamps & NBR O-Ring. End plate material is aluminum
T652AT502468001
End Plate Kit (1/2 NPTF): Includes two end plates and body-to-body assembly
clamps & FKM O-Ring. End plate material is aluminum
T652AT502468007
End Plate Kit (1/2 ISO228/1-G): Includes two end plates and body-to-body
assembly clamps & NBR O-Ring. End plate material is aluminum
T652AT502468002
End Plate Kit (1/2 ISO228/1-G): Includes two end plates and body-to-body
assembly clamps & FKM O-Ring. End plate material is aluminum
T652AT502468008
End Plate Kit (1/2 ISO 7/1 Rc): Includes two end plates and body-to-body
assembly clamps & NBR O-Ring. End plate material is aluminum
T652AT502468003
End Plate Kit (1/2 ISO 7/1 Rc): Includes two end plates and body-to-body
assembly clamps & FKM O-Ring. End plate material is aluminum
T652AT502468009
Wall/Panel Bracket Kit includes one bracket and two screws for attaching bracket
to body clamp. Two brackets are required for mounting three or more products.
One bracket is suitable for mounting two products. Material is aluminum.
P699AT502467001
Side Mounting Brackets (Includes two brackets): Designed for mounting single
products to wall or panel, but is capable of handling up to 3 stations. Material is
stainless steel.
P652AT503860002
Panel Nut: Used for Regulators and Filter-Regulators where adjustment knob is fed
through a panel and the panel nut is then used to secure the product to the panel.
Material is polyamide.
P652AT513177001
Panel Nut & Bracket: The panel nut and bracket are used to mount a Regulator or
Filter-Regulator to a wall or panel. Materials are stainless steel and polyamide.
P652AT503861002
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
47
SERIES
652
Repair Kits and Service Parts
652 Series - Spare Parts Kits
Description Kit Number
No Gauge
No Gauge Cover Kit - NBR Seal. Includes gauge cover, screw and o-ring M699AG503396001
No Gauge Cover Kit - FKM Seal. Includes gauge cover, screw and o-ring M699AG503396002
Low Profile
Gauges*
Low Profile Gauge - 651/652/653 Series: 0-90 PSI Scale with NBR seals M699AG438047005
Low Profile Gauge - 651/652/653 Series: 0-90 PSI Scale with FKM seals M699AG438047017
Low Profile Gauge - 651/652/653 Series: 0-175 PSI Scale with NBR seals M699AG438047004
Low Profile Gauge - 651/652/653 Series: 0-175 PSI Scale with FKM seals M699AG438047016
Low Profile Gauge - 653 Series: 0-375 PSI Scale with NBR seals M699AG438047006
Low Profile Gauge - 653 Series: 0-375 PSI Scale with FKM seals M699AG438047018
Low Profile Gauge - 651/652/653 Series: 0-6 bar Scale with NBR seals M699AG438047002
Low Profile Gauge - 651/652/653 Series: 0-6 bar Scale with FKM seals M699AG438047014
Low Profile Gauge - 651/652/653 Series: 0-12 bar Scale with NBR seals M699AG438047001
Low Profile Gauge - 651/652/653 Series: 0-12 bar Scale with FKM seals M699AG438047013
Low Profile Gauge - 653 Series and SOV for 651/652/653: 0-25 bar Scale
with NBR seals
M699AG438047003
Low Profile Gauge - 653 Series and SOV for 651/652/653: 0-25 bar Scale
with FKM seals
M699AG438047015
Pressure Range Indicators (Red/Green) for Low Profile Gauges. Desired
range can be easily set in the field. This kit allows customers to add the
pressure range indicator to existing low profile gauges in the field.
M699AG500179001
Low Profile Gauge with Pressure Range Indicator - 651/652/653 Series:
0-90 PSI Scale with NBR seals
M699AG438047011
Low Profile Gauge with Pressure Range Indicator - 651/652/653 Series:
0-175 PSI Scale with NBR seals
M699AG438047010
Low Profile Gauge with Pressure Range Indicator - 653 Series: 0-375 PSI
Scale with NBR seals
M699AG438047012
Low Profile Gauge with Pressure Range Indicator - 651/652/653 Series:
0-6 bar Scale with NBR seals
M699AG438047008
Low Profile Gauge with Pressure Range Indicator - 651/652/653 Series:
0-12 bar Scale with NBR seals
M699AG438047007
Low Profile Gauge with Pressure Range Indicator - 653 Series and SOV for
651/652/653: 0-25 bar Scale with NBR seals
M699AG438047009
Digital Gauge
Digital Pressure Gauge - 651/652/653 Series: 0-145 PSI Scale (User can
change units; bar, MPa, Kgf/cm
2
) 1/8" NPTF
M699AG504650001
Digital Pressure Gauge - 651/652/653 Series: 0-145 PSI Scale (User can
change units; bar, MPa, Kgf/cm
2
) 1/8" ISO 7/1 Rc
M699AG504650002
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
48
SERIES
652
Repair Kits and Service Parts
652 Series - Spare Parts Kits
Description Kit Number
Round
Gauges*
Round Gauge - 0-60 PSI Series 1/8 NPTF and 1.5" Face Diameter 214-116
Round Gauge - 0-160 PSI Series 1/8 NPTF and 1.5" Face Diameter 214-103
Round Gauge - 0-300 PSI 1/8 NPTF and 1.5" Face Diameter 214-118
Round Gauge - 0-60 PSI 1/8 ISO 7/1 Rc and 1.5" Face Diameter RA060
Round Gauge - 0-160 PSI 1/8 ISO 7/1 Rc and 1.5" Face Diameter 214-153
Round Gauge - 0-300 PSI 1/8 ISO 7/1 Rc and 1.5" Face Diameter RA300A
Round Gauge - 0-4 bar 1/8 ISO 7/1 Rc and 50 mm Face Diameter (Europe) 34200061
Round Gauge - 0-12 bar 1/8 ISO 7/1 Rc and 50 mm Face Diameter (Europe) 34200062
Round Gauge - 0-16 bar 1/8 ISO 7/1 Rc and 50 mm Face Diameter (Europe) 34200997
Port Plates
Gauge Port Plate Assembly - 1/8 NPTF M699AG440510001
Gauge Port Plate Assembly - 1/8 ISO 7/1 Rc M699AG440510002
Pressure
Switch/Sensor
DPS280 Pressure Switch/Sensor - NPN M8 with Cable 1/8 ISO 7/1 Rc DPS280NRQ8
DPS280 Pressure Switch/Sensor - PNP M8 with Cable 1/8 ISO 7/1 Rc DPS280PRQ8
DPS280 Pressure Switch/Sensor - NPN M8 with Cable 1/8 NPTF DPS280NNQ8
DPS280 Pressure Switch/Sensor - PNP M8 with Cable 1/8 NPTF DPS280PNQ8
Note: PS182 Series image
Pressure Switch: 1/8 NPTF, 20-130 PSI (1.4 to 9 bar) range, Brass/NBR 3 PIN M12
connection (12mm); IP65
PS182CAN01
Pressure Switch: 1/8 BSPP, 20-130 PSI (1.4 to 9 bar) range, Brass/NBR 3 PIN M12
connection (12mm); IP65
PS182CAG01
Pressure Switch: 1/8 NPTF, 14 - 150 PSI (1 to 10 bar) range, Zinc Plated Steel/NBR
Polyamide Connector Material, 4 PIN DIN Connector; IP65
PS180CAN01
Connector/Cord-set for PS182 - 90° Elbow: 5 Meter cable PS182-5-90
Connector/Cord-set for PS182 - Straight: 5 Meter cable PS182-5-ST
Lubricator
Repair Kits
Lubricator dome repair kit - NBR seals. Includes dome cover, screw and o-rings. M699AY506842001
Lubricator dome repair kit - FKM seals. Includes dome cover, screw and o-rings. M699AY506842002
Lubricator Level Switch assembly kit. Includes level switch, stainless steel retainer
ring, o-ring and bushing.
M699AG506837001
Lubricator Bowl Plug assembly: Includes Lubricator bowl plug, stainless steel
retainer ring and NBR o-ring.
M699AQ440512001
* * Each of the Low Profile and Round Gauges are dual scale; consult factory for further information. The scale that is listed in the description has the units located near
the outside of the scale. The other units would be on the inside.
Note: For all pressure switches & round gauges that are added to the 652 series products in the field, a port plate is required. The port plate can be added at the time of
order entry or as a kit.
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
49
SERIES
652
Repair Kits and Service Parts
652 Series - Spare Parts Kits
Description Kit Number
Filter Kits
Particulate Filter Repair Kit - Includes the filter retainer, head baffle, lower
end cap and bowl baffle.
M652AY506833001
Differential Pressure Pop-Up Indicator (NBR Seals) This is used for the
Coalescing Filters to provide visual indication when the filter element needs
to be replaced.
M699AG439851001
Differential Pressure Pop-Up Indicator (FKM Seals) This is used for the
Coalescing Filters to provide visual indication when the filter element needs
to be replaced.
M699AG439851004
DPI Plug (NBR Seals) This is used to plug the top port on the filter when a
Differential Pressure Indicator is not used.
M699AG439851002
DPI Plug (FKM Seals) This is used to plug the top port on the filter when a
Differential Pressure Indicator is not used.
M699AG439851005
Electric Differential Pressure Indicator (NBR Seals) This is used for the
Coalescing Filter only. It provides a contact that will actuate when the filter
element needs to be replaced.
M699AG439851003
Regulator
& Filter
Regulator
Kits
Adjusting Screw Repair Kit - Includes adjusting screw, nut, washer and
screw
M652AY506952001
Key Lockable Adjusting Screw Repair Kit - Includes adjusting screw,
adjusting nut, flat washer and screw
M652AY506952002
Tamper proof Repair Kit - Includes adjusting screw, adjusting nut, flat
washers and screws
M652AY506952003
Diaphragm Assembly Repair Kit (Pilot Operated Regulator NBR Seals) M652AH435268001
Diaphragm Assembly Repair Kit (Pilot Operated Regulator FKM Seals) M652AH435268002
Poppet Repair Kit (NBR Seals): Includes poppet, stem & seals. M652AY506863001
Poppet Repair Kit (FKM Seals): Includes poppet, stem & seals. M652AY506863002
Diaphragm Assembly Repair Kit (Relieving Regulator NBR Seals) M652AH434213001
Diaphragm Assembly Repair Kit (Relieving Regulator FKM Seals) M652AH434213002
Diaphragm Assembly Repair Kit (Non-Relieving Regulator NBR Seals) M652AH434213003
Diaphragm Assembly Repair Kit (Non-Relieving Regulator - FKM Seals) M652AH434213004
Main Spring (45 PSIG / 3 bar) M652AY513313001
Main Spring (60 PSI / 4 bar) M652AY438708001
Main Spring (125 PSI / 8 bar) M652AY438709001
Main Spring (145 PSI / 10 bar) M652AY513314001
Bowl Seal
Kits
U-Cup Seal Kit (NBR Seals) Kit contains 10 U-Cup seals. This seal is used
for all 652 series bowls
M652AH507085001
U-Cup Seal Kit (FKM Seals) Kit contains 10 U-Cup seals. This seal is used
for all 652 series bowls
M652AH507085002
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
50
SERIES
652
Repair Kits and Service Parts
652 Series - Spare Parts Kits
Description Part/Kit Number
3/2 Slow Start -
Quick Exhaust
Valve Kits
Horizontal Solenoid Operator (190) - With Manual Override 19090017
Horizontal Solenoid Operator (190) - Without Manual Override 19090005
24 VDC coil with 3 Pin M12 Connection, for Horizontal Solenoid Operator 43005525
24 VDC coil with DIN Spade connection for Horizontal Solenoid Operator 43004473
120 VAC coil with DIN Spade connection for Horizontal Solenoid Operator 43004471
24 VAC coil with DIN Spade connection for Horizontal Solenoid Operator 43004469
240 VAC coil with DIN Spade connection for Horizontal Solenoid Operator 43004472
DIN Connector, without LED - Horizontal Solenoid Operator 88122602
DIN Connector, with LED, for 24 VAC/DC coil - Horizontal Solenoid Operator 88122603
DIN Connector, with LED, for 120 VAC coil - Horizontal Solenoid Operator 88122605
DIN Connector, with LED, for 240 VAC coil - Horizontal Solenoid Operator 88122608
Vertical Solenoid Operator (189) - Without Manual Override 18990007
24 VDC coil with 3 Pin M12 Connection, for Vertical Solenoid Operator 43005523
24 VDC coil with DIN Spade connection for Vertical Solenoid Operator 43004166
120 VAC coil with DIN Spade connection for Vertical Solenoid Operator 43004419
24 VAC coil with DIN Spade connection for Vertical Solenoid Operator 43004416
240 VAC coil with DIN Spade connection for Vertical Solenoid Operator 43004422
DIN Connector, without LED - Vertical Solenoid Operator 88122404
DIN Connector, with LED, for 24 VAC/DC coil - Vertical Solenoid Operator 88122405
DIN Connector, with LED, for 120 VAC coil - Vertical Solenoid Operator 88122407
DIN Connector, with LED, for 240 VAC coil - Vertical Solenoid Operator 88122410
Jumper Plate Kit: For Air Operated Internally Piloted 3/2 Slow Start - QE Valve M699AY513316001
Pilot Port Plate: For Air Operated Externally Piloted 3/2 Slow Start - QE Valve M699AY513318001
Pilot Port Plate: For Air Operated Externally Piloted 3/2 Slow Start - QE Valve, 1/8
NPTF
M699AY513318002
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
51
SERIES
652
Accessories
652 Series - Accessories
Description Part Number
Scissor Lock
Scissor Lock for Shut-Off Isolation Valve & Lockout Valve VB-1
Mufflers/Silencers
Metal Muffler – 1/4 NPTF (Shut-Off Isolation Valves) M2MN
Polyethylene Muffler – 1/4 NPTF (Shut-Off Isolation Valves E2MN
Metal Muffler – 1/2 NPTF (Slow-Start/Quick Exhaust & Lockouts) M4MN
Polyethylene Muffler – 1/2 NPTF (Slow-Start/Quick Exhaust & Lockouts E4MN
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
52
SERIES
652
Particulate Filter Flow Charts - Particulate Filter 1/4
Particulate Filter 3/8
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 20 40 60 80 100 120 140
0
10
20
30
40
50
60
70
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
0 500 1000 1500 2000 2500 3000 3500 4000 4500
Flow - Q (SCFM)
Pressure Drop - P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 5 µ Filtration | 1/4 Ports
4.0 bar (58 PSIG)
2.5 bar (36 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 20 40 60 80 100 120 140 160 180
0
10
20
30
40
50
60
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Flow - Q (SCFM)
Pressure Drop - P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 25 µ Filtration | 1/4 Ports
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 20 40 60 80 100 120 140 160 180
0
10
20
30
40
50
60
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Flow - Q (SCFM)
Pressure Drop -
P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 40 µ Filtration | 1/4 Ports
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200
0
10
20
30
40
50
60
70
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
0 1000 2000 3000 4000 5000 6000
Flow - Q (SCFM)
Pressure Drop - P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 5 µ Filtration | 3/8 Ports
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200 250
0
10
20
30
40
50
60
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0 1000 2000 3000 4000 5000 6000 7000 8000
Flow - Q (SCFM)
Pressure Drop - P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 25 µ Filtration | 3/8 Ports
4.0 bar (58 PSIG)
2.5 bar (36 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200 250
0
10
20
30
40
50
60
70
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
0 1000 2000 3000 4000 5000 6000 7000 8000
Flow - Q (SCFM)
Pressure Drop -
P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 40 µ Filtration | 3/8 Ports
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
53
SERIES
652
Regulator Flow Charts
0 50 100 150 200 250 300
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 1000 2000 3000 4000 5000 6000 7000 8000 9000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Regulator | 1/2 Ports
P1 = 10 Bar (145 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 1000 2000 3000 4000 5000 6000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Regulator | 1/4 Ports
P1 = 10 Bar (145 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200 250
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 1000 2000 3000 4000 5000 6000 7000 8000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Regulator | 3/8 Ports
P1 = 10 Bar (145 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
Particulate Filter Flow Charts - Particulate Filter 1/2
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200
0
10
20
30
40
50
60
70
80
0
1
2
3
4
5
6
0 1000 2000 3000 4000 5000 6000
Flow - Q (SCFM)
Pressure Drop - P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 5 µ Filtration | 1/2 Ports
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200 250
0
10
20
30
40
50
60
70
80
0
1
2
3
4
5
6
0 1000 2000 3000 4000 5000 6000 7000 8000
Flow - Q (SCFM)
Pressure Drop - P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 25 µ Filtration | 1/2 Ports
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200 250
0
10
20
30
40
50
60
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0 1000 2000 3000 4000 5000 6000 7000 8000
Flow - Q (SCFM)
Pressure Drop -
P (PSIG)
Pressure Drop -
P (bar)
Flow - Q (l/min ANR)
652 Filter | 40 µ Filtration | 1/2 Ports
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
54
SERIES
652
Particulate Filter/Regulator Flow Charts - Particulate Filter/Regulator Filter 1/4
Particulate Filter/Regulator Flow Charts - Particulate Filter/Regulator Filter 3/8
0 20 40 60 80 100 120 140
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 500 1000 1500 2000 2500 3000 3500 4000 4500
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 5 µ Filtration | 1/4 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 20 40 60 80 100 120 140 160
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 25 µ Filtration | 1/4 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 20 40 60 80 100 120 140 160
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 40 µ Filtration | 1/4 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 20 40 60 80 100 120 140 160
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 5 µ Filtration | 3/8 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 1000 2000 3000 4000 5000 6000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 25µ Filtration | 3/8 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 1000 2000 3000 4000 5000 6000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 40µ Filtration | 3/8 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
Information subject to change without notice. For ordering information or regarding your local sales office visit www.numatics.com.
55
SERIES
652
Particulate Filter/Regulator Filter 1/2
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 20 40 60 80 100 120 140 160
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 5 µ Filtration | 1/2 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 1000 2000 3000 4000 5000
6000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 25 µ Filtration | 1/2 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
2.5 bar (36 PSIG)
4.0 bar (58 PSIG)
6.3 bar (91 PSIG)
8.0 bar (116 PSIG)
0 50 100 150 200
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
0 1000 2000 3000 4000 5000 6000
Flow - Q (SCFM)
Pressure P2 (PSIG)
Pressure - P2 (Bar)
Flow - Q (l/min ANR)
652 Filter-Regulator | 40 µ Filtration | 1/2 Ports
P1 = 10 Bar (145 PSIG) |
P = 1 Bar (14.5 PSIG)
World Headquarters
Numatics, Inc. | Tel (248) 596-3200 | www.numatics.com | email: insidesales@numatics.com
652Series Rev 9/15
© Numatics Inc. 2012-2013
Numatics
®
is registered in the United States and elsewhere
USA - Numatics, Incorporated
46280 Dylan Drive
Novi, Michigan 48377
P: 248-596-3200
F: 248-596-3201
Canada - Numatics, Ltd
P: 519-758-2700
F: 519-758-5540
Brazil - Ascoval Ind.e Comercio Ltda
P: (55) 11-4208-1700
F: (55) 11-4195-3970
México - Ascomatica SA de CV
P: 52 55 58 09 56 40 (DF y Area metropolitana)
P: 01 800 000 2726 (Interior de la República)
F: 52 55 58 09 56 60
