DESCRIPTION
A solenoid-operated, 4-way, 3-position, direct-acting, spool-type, motor center,
screw-in hydraulic cartridge valve.
OPERATION
When de-energized, the SV10-47E blocks flow at 3 and 4, while allowing flow from 2
to 1. When coil #1 (S1) is energized, the spool shifts to allow flow from 3 to 4 and 2 to
1. When coil #2 (S2) is energized flow is allowed from 2 to 3 and from 4 to 1.
In circuits where work port flows are unequal due to cylinder ratios, the higher return
flow should be directed to port 2.
While 1 may be fully pressurized, it is not intended for use as the valve’s inlet.
FEATURES
• Continuous-duty rated solenoid with optional coil voltages and terminations.
• Hardened precision spool and cage for long life.
• Manual override option.
• Optional waterproof E-Coils rated up to IP69K.
• Efficient wet-armature construction.
• All ports may be fully pressurized.
• Cartridges are voltage interchangeable.
• Unitized, molded coil design.
• Industry common cavity.
RATINGS
Operating Pressure: 250 bar (3625 psi)
Proof Pressure: 344 bar (5000 psi)
Flow: Up to 30.2 (8 gpm); see performance chart
Internal Leakage: 328 cc/minute (20 cu. in./minute) max. at 207 bar (3000 psi)
Temperature: -40 to 100°C (-40° to 212°F) with standard Buna N seals;
-26 to 204°C (-15°F to 400°F) with Fluorocarbon seals;
-54 to 107°C (-65°F to 225°F) with Polyurethane seals
Coil Duty Rating: Continuous from 85% to 115% of nominal voltage
Response Time: First indication of change of state with 100% voltage supplied at
80% of nominal flow rating: Energized: 40 msec.; De-energized: 10 msec.
Initial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC;
0.18 amps at 115 VAC (full wave rectified).
E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC
Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: VC10-4; See page 9.110.1; Cavity Tool: CT10-4XX; See page 8.600.1
Seal Kit: SK10-4X-MMM; See page 8.650.1
Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180
Coil Spacer: Std. D-Coil Spacer Part No. 7000280; E-Coil Spacer Part No. 4539700;
If cartridge is ordered "Less Coil," D-Coil spacer will be provided unless an E is
specified in the Coil Termination To Order section.
SV10-47E Spool, 4-Way, 3-Position
SYMBOL
PERFORMANCE (Cartridge Only)
1.542.1
4
3
2
1
SOLENOID VALVES
HYDRAFORCE
.com
®
8.6/125
6.9/100
5.2/75
3.4/50
1.7/25
6.9/100
5.2/75
3.4/50
1.7/25
3.8
1
11.4
3
15.9
4
18.9
5
7.5
2
FLOW lpm/gpm
PRESSURE bar/psi
22.7
6
3 to 4 (S1 Energized) ———
3 to 1 (S2 Energized) — - — -
4 to 1 (S2 Energized) – – – –
2 to 1 (De-Energized) - - - - - -
2 to 1 (S1 Energized) — — —
32 cSt/150 sus oil at 40°C
See following page for additional
performance information.
Blue rectangles are links to other catalog pages.