HSV10-20 HyPerformance
TM
Poppet, 2-Way, N.C.
DESCRIPTION
A solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydraulic
cartridge valve, designed to function as a load holding or blocking valve in high
pressure applications requiring low internal leakage.
OPERATION
When de-energized, the HSV10-20 acts as a check valve, allowing flow to pass
from 1 to 2, while blocking flow in the reverse direction.
When energized, the poppet lifts to open the 2 to 1 flow path.
In this mode, flow from 1 to 2 is severely restricted.
Operation of Manual Override Option: The manual override feature is intended for
emergency use, not continuous duty operation. To operate (de-energized) the manual
override pin must be seated in the lower detent groove. To shift the valve manually,
the operator pushes down on the knob and rotates 180° in either direction. When the
manual override is actuated, increased flow can be achieved by pulling on the knob.
FEATURES
• Manual override option.
• Continuous-duty rated solenoid.
• Hardened seat for long life and low leakage.
• Optional coil voltages and terminations.
• Efficient wet-armature construction.
• Cartridges are voltage interchangeable.
• Waterproof E-Coils rated up to IP69K.
• 1000-hour salt-spray rated solenoid tubes and coils.
• Unitized, molded coil design.
• All HyPerformance products are tested to the rigorous standards
of the NFPA specification T2.6.1.
• All HyPerformance valves are tested at a verification level of 90%
and an assurance of 99%.
RATINGS
Operating Pressure: 350 bar (5075 psi); 10% cycle life: 420 bar (6090 psi)
Note: All HyPerformance products are tested for 900K cycles at 350 bar
and 100K cycles at 420 bar.
Proof Pressure: 690 bar (10,000 psi)
Burst Pressure: 1380 bar (20,000 psi)
Flow: Up to 75.7 lpm (20 gpm)
Internal Leakage: 0.25 cc/minute (5 drops/minute) max. with 350 bar (5075 psi)
at port 2.
Temperature: -54° to 107°C (-65° to 225°F) with Urethane seals
Coil Duty Rating: Continuous from 85% to 115% of nominal voltage
Response Time: First indication of change of state with 100% voltage supplied at
80% of nominal flow rating: Energized: 40 msec.; De-energized: 32 msec.
Initial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC
Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC10-2; See page 9.110.1
Cavity Tool: HCT10-2xx; See page 8.600.1
Seal Kit: SK10-2U-O; See page 8.650.1
Coil Nut: Part No. 4553800
1.017.1
ISO SYMBOL
PERFORMANCE
(Cartridge Only)
SOLENOID VALVES
HYDRAFORCE
.com
®
10.3/150
12.4/180
14.5/210
16.6/240
8.3/120
6.2/90
4.1/60
2.1/30
18.9
5
37.9
10
56.8
15
FLOW lpm/gpm
PRESSURE DROP bar/psi
Port 2 to 1, energized ——
Port 1 to 2, de-energized - - - -
32 cSt/150 sus oil at 40°C
75.7
20
Blue rectangles are links to other catalog pages.