FEATURES
• High flow rate due to optimized casted housing
• Small hysteresis by super finish of moving parts
• Long life cycle times by armature switching under oil
• Minimal wear by hardened and ground valve piston
• Simple exchangeability by international standardized hole pattern
to ISO 4401
SPECIFICATIONS
Operating pressure: ports P,A,B max. 320 bar
port T max. 210 bar
Nominal flow: max. 90 l/min (see performance chart)
Hysteresis: (in % of Qmax): < 6 %
Repeat accuracy: (in % of Qmax) < +/- 1,5 %
Switch-on time: (0-100%) 50 ms
Switch-off time: (100-0%) 70 ms
Media operating temp.range: -20°C up to +80°C
Ambient temperature range: -20°C up to +50°C
Hydraulic fluid: Hydraulic fluid to DIN 51524 part 1 / 2
Viscosity range: 10 mm
2
/s up to 400mm
2
/s
Fil
tration: Class 18/16/13 up to 19/17/14
according to ISO4406
Supply voltage: DC voltage
Nominal current: 2,60 A at 12VDC
1,60 A at 24VDC
Resistance at 20°C: 3,40 Ohm at 12VDC
8,65 Ohm at 24VDC
Coil duty rating: 100% continuous
Electromagnetic
compatibility: (EMC) Emissions to EN 50081-1
compatibility to EN 50082-2
to Norm 89/336 CEE
IP rating: IP65
Installation: no orientation restrictions
Hint: Vent system and valve before
setting in motion
Hole pattern: ISO4401-05-04-0-94
Weight: 5,9 kg
4/3-Proportional solenoid valve,
dir
ect acting
subplate to ISO4401
P4WE 10
FUNCTION
The P4WE 10 is a direct acting
solenoid valve which combines the
directional control with the velocity
control of the consumer.
The controlled nominal flow is
proportional to the electrical input
signal at the coil.
Analogue to his size the coil creates
a force and moves the piston against
the spring. Herewith the
corresponding cross section
diameters are opened which
determines the flow rate in
dependence of the pressure
differential.
For the electrical control of the valve
there are electronic modules
available (see brochure 5.249.2.0
PEM-XD).
SYMBOL
E
J
up
to 90 l/min
up to 320 bar
E 5.229.0 /08.10
764
∆p P-T (bar)
∆p P-T (bar)
∆p P-T (bar)
∆p P-T (bar)
PERFORMANCE
measured at T oil = 46°C and 33 mm²/s (The related ∆p is measured between lines P and T of the valve)
E30
E60
J30
J60
765
Name
Proportional solenoid valve
Subplate mounting
Nominal size
10
Symbol
E
J
Nominal flow
30 = 30 l/min
60 = 60 l/min (At ∆p=10 bar P-T)
Type
D01 = standard type with
manual override
Nominal voltage
12= 12 V DC
24= 24 V DC
Coil connector
PG= DIN plug to EN175301-803
Seal material
V= FPM (Standard)
N= NBR (optional)
MODEL CODE
P4WE10 E 30 D01- 24PG /V
DIMENSIONS
Standard models Part No.
P4WE 10 E30 D01-24PG/V 6078958
P4WE 10 E60 D01-24PG/V 6078960
P4WE 10 J30 D01-24PG/V 6078962
P4WE 10 J60 D01-24PG/V 6078964
Other types on request
1) Mounting plate with O-rings 4x 12,42 x 1,78
2)
Manual override
3) Free space for mounting the coil
4) DIN plug to EN175301-803
5) Free space for mounting the plug
Fastening screws: 4x M6 x 40 torque 8 Nm +0,5 Nm
All dimensions in mm. Fastening elements are not in the scope of delivery.
Hole pattern
HYDAC Fluidtechnik GmbH
Justus-von-Liebig-Str. 5
66280 Sulzbach / Saar
Tel.: 06897 / 509 -0
Fax: 06897 / 509 -598
Email: flutec@hydac.com
Annotation
The technical information in this
brochure are relating to the operating
conditions and applications.
At deviant applications and/or
operating conditions please contact
the technical dept.
Technical information are
subject to technical modifications.
766
