DESCRIPTION FEATURES

EN 5.228.1. 2_05.22

 High nominal flow due to optimized, cast casing

 Low hysteresis due to precision machining of moving parts

 Easy interchangeability due to internationally standardised interface

ISO 4401

 Electronic control by EHCD (see brochure 2.429.2)

HYDAC 4/2 and 4/3 proportional

directional valves of the P4WE

series combines directional control

with speed control of the consumer.

The controlled volume flow is

proportional to the electrical input

signal on the solenoid.

4/2 and 4/3 Proportional directional valve

direct-acting

P4WE 6

Nominal size 6

up to 40 l/min

up to 350 bar

CONTENT

Description 1

Features 1

Model code 2

Spool types / Symbols 2

Technical Data 3

Function 3

Section view 3

Performance 4

Dimensions 6

Electrical connections 7

Manual overrides 7

Accessories 7

MODEL CODE

EN 5.228.1. 2_05.22

P4WE6EA16A01 –24PG/V

Type

Proportional directional valve with 4 main ports, direct-acting

Nominal size

Symbol

See page 2

Nominal flow (bei Δp = 10 bar, P → T)

04 = 4 l/min

08 = 8 l/min

16 = 16 l/min

26 = 26 l/min

Series

A01 = specified by the manufacturer

Rated voltage of the solenoid coil

12 = 12 VDC

24 = 24 VDC

Coil type (Details see page 7)

PG = device connector to DIN EN175301-803

PN = Deutsch connector

Sealing material

V = FKM (standard)

N = NBR

4/2-DIRECTIONAL SPOOL VALVES 4/3-DIRECTIONAL SPOOL VALVES

Type Basic model Type Basic model

EA E

QA Q

SPOOL TYPES / SYMBOLS

a P

FUNCTION

SECTION VIEW

The proportional valves of the P4WE series

are direct-acting proportional valves.

The volume flow is controlled continuously

(proportionally) to the electrical input signal

at the solenoid coil.

The valve consists of a valve casing (1), a

control piston (2) and two proportional

solenoids (3).

According to the input signal, the solenoid

generates a force and shifts the piston

against a spring. This releases cross-

sections, which define the size of the

volume flow, depending on the pressure

difference at the relevant control element.

For electronical control of the coil there are

electronic controls available (see brochure

5.249.2).

Hint:

Vent system and valve before setting in

motion.

Caution:

The valves are available in 12V and 24V

coil versions. A 24VDC supplied control

electronics enables improved dynamic and

hysteresis values for a valve with 12V coil.

A control electronic supplied with 12VDC

can only be used in combination with a 12V

coil version. Then the dynamic advantage

of the valve is lost.

TECHNICAL DATA ¹

EN 5.228.1. 2_05.22

General specifications

MTTF

150 - 1200 years, according to DIN EN

ISO 13849-1:2016; Table C.1,

confirmation of ISO 13849-2:2013; Tables

C.1 and C.2

Ambient temperature [°C] -20 to +60

Installation position No orientation restictions

Weight [kg] 1,5 one solenoid;

2,0 two solenoids

Material Valve casing: Cast iron

Name plate: Aluminium

Surface coating Valve casing: Phosphate coated

Hydraulic specifications

Operating pressure [bar] Port P, A, B: p

max

= 350

Port T: p

max

= 210

Flow rate

(bei Δp A → B min. 10 bar) [bar] see performance curves on page 4

Operating fluid

Hydraulic oil to DIN 51524 part 1, 2 and 3

Media operating temperature range [°C] -20 to +80

Viscosity range [mm²/s] 10 to 400

Permitted contamination level

of operating fluid

class 18/16/13 according to ISO 4406

Max. switching frequency [1/h] 7.000

Hysteresis [%] 6 of Q

max

Repeatability [%] ±1,5 of Q

max

Sealing material FKM (standard), NBR

Electrical specifications

Switching time [ms] Switch-on: 50 to 100

Switch-off: 10 to 60

Switching times are highly dependent on

pressure, flow rate and application of the valve.

Type of voltage DC

Rated voltage [V] 12 24

Max. current [A] 2,25 1,6

Resistance at 20°C [Ω] 2,7 5,0

Voltage tolerance [%] ±10

Duty cycle [%] 100

Protection class to DIN EN 60529 with electrical connection “G“ IP65 ²

with electrical connection “N“ IP65 ²

¹ see „Conditions and Instructions for Valves“ in brochure 53.000

² if installed correctly

measured at T

oil

= 42°C and 36 mm²/s and flow on both sides of the spool (z.B. PABT)

The performance curves represent typical flow curves for different valve spools. The first curve shows the flow value

at constant Δp, depending on the solenoid current. The second curve describes the dependency of flow value and Δp

at constant solenoid current.

The total valve pressure drop (Δp) was measured between port P and T of the valve.

Hint: I

eff

= I

efficient

= I

max

-I

empty

PERFORMANCE

EN 5.228.1. 2_05.22

E 04 spool

E 08 spool

E 16 spool

PERFORMANCE

EN 5.228.1. 2_05.22

Q 04 spool

Q 08 spool

Q 16 spool

E 26 spool

EN 5.228.1. 2_05.22

Interface to ISO 4401-03-02-0-05 (Cetop 3)

DIMENSIONS

clamping length

With two solenoids

Q 26 spool

Mounting screws:

(not included in delivery)

DIN EN ISO 4762 - M5 x 50 - 10.9

Torque: 7 Nm

EN 5.228.1. 2_05.22

HYDAC Fluidtechnik GmbH

Justus-von-Liebig-Str.

D-66280 Sulzbach/Saar

Tel: 0 68 97 /509-01

Fax: 0 68 97 /509-598

E-Mail: valves@hydac.com

* For further information see brochure "Control modules for hydraulic drives -EHCD“

catalogue-24000.2/10/14 or contact customer support EHCD@hydac.com.

Designation Part no.

Seal kits

(4-part set)

9,25 x 1,78 90 Sh FKM 3120269

9,25 x 1,78 90 Sh NBR 3492432

Mounting screws (4 pcs) ISO 4762 M5 x 50 – 10.9 4312231

Solenoids coils

COIL 12PG- 2.7 -50-2345 -S 4356846

COIL 12PN- 2.7 -50-2345 -S 4356849

COIL 24PG- 5 -50-2345 -S 4356848

COIL 24PN- 5 -50-2345 -S 4356851

Seal kit for solenoid coil Nut open, O-ring 4317299

Connector

Z4 standard 2-pole without PE 394287

ZW4 incl. rectifier 394293

Z4L incl. LED 394285

Control module EHCD* AM005XXXU 6158999

ACCESSORIES

With one solenoid

Note

The information in this brochure relates to the operating conditions and

applications described. For applications not described, please contact the

relevant technical department.

All technical details are subject to change without notice.

ELECTRICAL CONNECTIONS

Other models on request

Device

connector

DIN EN

175301-803 A

Device

connector

Deutsch

(DT04-2P)

• IP65 / IP67

• Optional with

Suppressor diode

•IP65

• A = 28 mm for DC

(DG)

MANUAL OVERRIDES

* Dimensions up to valve housing

In case of emergency, the valve can also be operated

manually. There are different forms of manual override

available.

The tank pressure should not exceed 50 bar. If the tank

pressure is higher, the force required to operate the

manual override increases accordingly.

For valves with two solenoids, simultaneous operation of

both manual overrides is not permitted.

Standard

with

concealed

manual

override

Operation

with tool