53.85
2.1
123.50
4.9
63.50
2.5
36.30
1.4
S1
S2
DESCRIPTION
OPERATION
FEATURES
A screw-in cartridge, solenoid operated, 4-way, 3 position, direct
acting, spool type, proportional directional valve.
When in neutral, all ports are blocked. When S1 is energized, flow is allowed
from 3 to 4, and from 2 to 1. When S2 is energized, flow is allowed from 3 to 2,
and from 4 to 1. Flow rate is directly proportional to coil current. In circuits
where work port flows are unequal due to cylinder ratios, the higher return
flow should be directed to port 2.
- Excellent stability throughout flow and pressure range
- Excellent dynamic performance
-1000 hours minimum salt fog to red rust protection per ASTM B1117
- Hardened and ground valve components to ensure minimal wear
and extended service life
APPLICATION CIRCUIT
01
2602074
SHEET 1 OF 3
SCALE: 2:3
WEIGHT:
Revision
DWG. NO.
B
SIZE
TITLE:
NAME
DATE
APPROVED
CHECKED
DRAWN
NONE
x
HEAT TREAT:
MATERIAL:
Hydraulic
Division
PROPRIETARY DRAWING - Distribution, reproduction or disclosure
of information pertaining to this drawing or design to any party other
than those directly working with HYDAC is strictly prohibited without
the written consent of HYDAC.
Glendale Heights, Illinois, USA
THIRD ANGLE PROJECTION
NONE
FINISH:
SolidWorks 2016
DO NOT SCALE
ANSI Y14.5
DIMENSIONS ARE IN INCHES [mm]
ANGULAR
2 DEGREES
LINEAR TOLERANCES:
FRACTIONAL
.015
TWO PLACE DECIMAL
.01
THREE PLACE DECIMAL
.005
SURFACE FINISH 125 RMS
BREAK EDGES .005/.002
SQUARENESS WITHIN .005
T.I.R. OF COMMON AXIS FEATURES .010 MAX.
UNLESS OTHERWISE SPECIFIED:
DATE
BY
CHANGE
NUMBER
REV
05-23-18
lbs
05-23-18
JRT
PWK10E36-01.-C- . -0
DATA SHEET
00
JRT
RJH
CW
EXPERIMENTAL DRAWING
PRODUCTION RELEASED DRAWING
x
01
01-30-19
JRT
50.55
2.0
38.10
1.5
A
76.20
3.0
7.10
.3
63.50
2.5
35.05
1.4
53.98
2.1
18.80
.7
123.00
4.8
101.60
4.0
7.00 [.3]
SLOT TO
C
L
OF
FC10-4 CAVITY
9.53 [.4]
TO
C
L
OF
FC10-4 CAVITY
PORT SLOT DETAIL A
SCALE 1 : 1
MODEL CODE
01
SHEET 2 OF 3
SCALE: 1:2
WEIGHT:
Revision
DWG. NO.
B
SIZE
TITLE:
NAME
DATE
APPROVED
CHECKED
DRAWN
NONE
x
HEAT TREAT:
MATERIAL:
Hydraulic
Division
PROPRIETARY DRAWING - Distribution, reproduction or disclosure
of information pertaining to this drawing or design to any party other
than those directly working with HYDAC is strictly prohibited without
the written consent of HYDAC.
Glendale Heights, Illinois, USA
THIRD ANGLE PROJECTION
NONE
FINISH:
SolidWorks 2012
DO NOT SCALE
ANSI Y14.5
DIMENSIONS ARE IN INCHES [mm]
ANGULAR
2 DEGREES
LINEAR TOLERANCES:
FRACTIONAL
.015
TWO PLACE DECIMAL
.01
THREE PLACE DECIMAL
.005
SURFACE FINISH 125 RMS
BREAK EDGES .005/.002
SQUARENESS WITHIN .005
T.I.R. OF COMMON AXIS FEATURES .010 MAX.
UNLESS OTHERWISE SPECIFIED:
DATE
BY
CHANGE
NUMBER
REV
05-23-18
lbs
05-23-18
JRT
00
JRT
EXPERIMENTAL DRAWING
PRODUCTION RELEASED DRAWING
2602074
PWK10E36-01.-C- . -0
DATA SHEET
RJH
CW
01
01-30-19
JRT
Pressure Differential vs Flow
Flow vs % Input Command (Compensated) Flow vs % Input Command (Uncompensated)
Flow vs Pressure Differential (Uncompensated)
01
SHEET 3 OF 3
SCALE: 1:2
WEIGHT:
Revision
DWG. NO.
B
SIZE
TITLE:
NAME
DATE
APPROVED
CHECKED
DRAWN
NONE
x
HEAT TREAT:
MATERIAL:
Hydraulic
Division
PROPRIETARY DRAWING - Distribution, reproduction or disclosure
of information pertaining to this drawing or design to any party other
than those directly working with HYDAC is strictly prohibited without
the written consent of HYDAC.
Glendale Heights, Illinois, USA
THIRD ANGLE PROJECTION
NONE
FINISH:
SolidWorks 2012
DO NOT SCALE
ANSI Y14.5
DIMENSIONS ARE IN INCHES [mm]
ANGULAR
2 DEGREES
LINEAR TOLERANCES:
FRACTIONAL
.015
TWO PLACE DECIMAL
.01
THREE PLACE DECIMAL
.005
SURFACE FINISH 125 RMS
BREAK EDGES .005/.002
SQUARENESS WITHIN .005
T.I.R. OF COMMON AXIS FEATURES .010 MAX.
UNLESS OTHERWISE SPECIFIED:
DATE
BY
CHANGE
NUMBER
REV
05-23-18
lbs
05-23-18
JRT
00
JRT
EXPERIMENTAL DRAWING
PRODUCTION RELEASED DRAWING
x
2602074
PWK10E36-01.-C- . -0
DATA SHEET
RJH
CW
01
01-30-19
JRT