EATON Screw-In Cartridge Valves E-VLSC-MC001-E December 2009A-380.A
An Eaton Brand
A
Where measurements are critical request certified drawings. We reserve the right to change specifications without notice.
Ratings and Specifications
Performance data is typical with fluid at 21,8 cSt (105 SUS) and 49° C (120° F)
Typical Application pressure (all ports) 350 bar (5000 psi)
Cartridge fatigue pressure (infinite life) 310 bar (4500 psi)
Rated Flow 114 L/min (30 USgpm)
Internal leakage 5 drops/min, max @ 350 bar (5000 psi)
Temperature range -40° to 100°C (-40° to 212°F)
Coil duty Continuous from 85% to 110% of nominal voltage
Cavity C-12-2 or C-12-2U
Add “U” after number if undercut is required. If undercut is not specified,
expect 10 psi@15 USgpm and 20 psi @ 30 USgpm higher pressure drop.
Fluids All general purpose hydraulics fluids such as:
MIL-H-5606, SAE 10, SAE 20 etc.
Filtration Cleanliness code 18/16/13
Housing material (standard) Aluminum or steel
Weight including coil 0,27 kg (0.59 lbs)
Seal kit 02-165889 (Buna-N), 02-165888 (Viton
®
)
Viton is a registered trademark of E.I. DuPont
Operation
In the de-energized position the
valve is open in both directions.
A series of internal check valves
allows full flow in both direc-
tions.
When the solenoid is energized
the pilot poppet closes the pilot
orifice causing the main poppet
to close.
Features
Hardened and ground work-
ing parts. Lapped seat for
low leakage. IP69K Tough coil
compatibility. Continuously
rated. Compact design with low
pressure drop. 350 bar working
pressure.
Description
This is a 2-way 2-position,
high pressure bi-directional,
pilot operated, normally open
poppet type screw in cartridge
valve. The valve is ideal for
isolating and holding actuators
in position.
SBV11-12-O - Solenoid Valve
Bi-directional, poppet type, normally open solenoid valve
114 L/min (30 USgpm) • 350 bar (5000 psi)
Pressure Drop
Cartridge only
Performance
Sectional View
A - Port 1 to port 2
B - Port 2 to port 1
2
1
150
100
50
Pressure Drop - psi
8
4
2
Pressure D rop - bar
6
A
B
0 20 40 60 80 100
Flow - L/m in (21,8 cSt oil @ 49°C)
0 105 15 20 25 30
Flow - U Sgpm (105 SUS oil @ 120°F)
2
1
EATON Screw-In Cartridge Valves E-VLSC-MC001-E December 2009 A-381.A
An Eaton Brand
A
Where measurements are critical request certified drawings. We reserve the right to change specifications without notice.
SBV11-12-O - Solenoid Valve
Bi-directional, poppet type, normally open solenoid valve
114 L/min (30 USgpm) • 350 bar (5000 psi)
1
Function
SBV11 - Solenoid
bi-directional valve
2
Size
12 - 12 size
3
Seal Material
Blank - Buna-N
V - Viton
®
4
Style
O - Normally open
5
Valve Housing Material
Blank - Cartridge only
A - Aluminum
S - Steel
Model Code
1 2
12
3
(V)
4
O
5
(*)
6
**
7
****
8
*
9
H
8
Connector Types
Blank - No coil
G - ISO 4400 DIN 43650
Q - Spade terminals
W - Flying lead
N - Deutsch (DC only)
Y - Amp JR (DC only)
D - Metripack 150 male
(DC only)
J - Metripack 280 male
(DC only)
9
Coil Series
H - 10 series, 29 W
For coil dimensions see section C.
10
Special Features
00 - None
(Only required if valve has special
features, omitted if “00.”)
Code Port Size Housing Number
Aluminium Steel
0 Cartridge only
4G 1/2" BSPP 02-161118 02-172062
4GU 1/2" BSPP 02-161116 02-172512
6G 3/4" BSPP 02-161117 02-169665
6GU 3/4" BSPP 02-161115 02-162922
10T SAE 10 02-160640 02-169744
10TU SAE 10 02-160641 02-169817
12T SAE 12 02-160644 02-169782
12TU SAE 12 02-160645 02-169790
See section J for housings.
6
Port Size
7
Voltage Rating
00 - No coil
12D - 12VDC
24D - 24VDC
36D - 36VDC
24A - 24VAC
115A - 115VAC
230A - 230VAC
12B - 12VDC/w diode*
24B - 24VDC/w diode*
*Optional arc suppression diode.
Dimensions
mm (inch)
Torque cartridge in housing
A - 81-95 Nm (60-70 ft lbs)
S - 102-115 Nm (75-85 ft lbs)
Note: When solenoid valve
is ordered as cartridge only,
coil nut is included.
Installation Drawing (Steel)Cartridge Only
WARNING
Maintain 5-8 Nm
(4-6 ft lbs) maximum
torque on valve tube nut.
Over tightening may cause
valve failure.
•
WARNING
Aluminum housings
can be used for
pressures up to 210 bar (3000
psi). Steel housings must be
used for operating pressures
above 210 bar (3000 psi).
•
– – – – –
2X 10.31
(.406)
88.9
(3.50)
88.9 (3.50)
63.5 (2.50)
63.5
(2.50)
12.7
(.50)
60.3
(2.37)
12.7
(.50)
28.7
(1.13)
25.4
(1.00)
2
1
Ø
23,75
(0.935)
31,75
(1.250)
hex
1.062"–
12 Thd.
22,2 (0.875) hex
Ø 38,9
(1.53)
29,6
(1.16)
60,
3
(2.3
44,
7
(1.7
1
2
