85 330/120 ED
1/20
DXRE*J
DIRECTIONAL CONTROL VALVES,
PILOT OPERATED,
WITH OBE AND FEEDBACK
SERIES 31
OPERATING PRINCIPLE
85 330/120 ED
SUBPLATE MOUNTING
DXRE5RJ ISO 4401-05
DXRE7J ISO 4401-07
DXRE8J ISO 4401-08
DXRE10J ISO 4401- 10
DXRE11J ISO 4401- 10 oversize ports
— DXRE*J are directional control valves operated by a servo-
proportional pilot, with mounting surface compliant with ISO 4401
standards. The main spool position is controlled by a linear
transducer LVDT in closed loop, which ensures high precision and
repeatability. .
— The valve is featured by integral electronic based on SMD technology
which ensures standard regulations and simplifies the electric wiring.
The unit doesn’t require any adjustment other than the possible
electronic regulation of the zero.
— Two types of integrated electronics are available, with analogue or
fieldbus interfaces.
— Suitable for control applications with closed loop of position, velocity
and pressure. With a power down or without the enable input, the
main spool is set to a fail-safe position by springs.
DXRE5RJ DXRE7J DXRE8J DXRE10J DXRE11J
Max operating pressure:
P - A - B ports
T - X - Y ports
bar
350
250
Controlled flow with ∆p 10 bar P-T l/min 100 220 400 800 1000
Hysteresis % Q
max
< 0.2%
Repeatability % Q
max
± 0.1%
Electrical characteristics
see paragraph 4
Ambient temperature range
°C -20 / +60
Fluid temperature range
°C -20 / +80
Fluid viscosity range
cSt 10 ÷ 400
Fluid contamination degree
According to ISO 4406:1999 class 18/16/13 (16/14/11 for longer life)
Recommended viscosity
cSt 25
Mass
kg 8 10.2 17 56 56
HYDRAULIC SYMBOL (typical)
PERFORMANCES
(obtained with mineral oil with viscosity of 36 cSt at 50°C and p =140 bar)
G
Z
PT
BA
G
UU
85 330/120 ED
2/20
DXRE*J
SERIES 31
1 - IDENTIFICATION CODE
1.1 - Standard electronics
Seals:
N = NBR seals for mineral oil (standard)
V = FPM seals for special fluids
Main connector:
6 pin + PE
Series No.
(the overall and mounting dimensions remain unchanged
from 30 to 39)
Drainage: I = internal
E = external
Nominal size:
5R = ISO 4401-05
7 = ISO 4401-07
8 = ISO 4401-08
10 = ISO 4401-10
11 = ISO 4401-10 with oversize
ports
Piloting: I = internal
E = external
Reference signal:
E0 = voltage ± 10 V
E1 = current 4 ÷ 20 mA
Proportional directional
valve with high-response
pilot
Standard electronics for
closed loop
D X R E J - / 31 - K11/
Pin C function:
A = external enable
B = internal enable
C = 0V monitor
1.2 - Surface treatments
The standard valve is supplied with surface treatment of phosphating black.
The zinc-nickel finishing makes the valve suitable to ensure a salt spray resistance up to 600 hours (test operated according to UNI EN
ISO 9227 standards and test evaluation operated according to UNI EN ISO 10289 standards).
Option:
/ W7 = Zinc-nickel
surface treatment
Omit if not required.
(see par. 1.2)
Spool type:
C = closed centre
A = open centre
Z = zero overlap
See par. 3 for operation and available flow rates.
85 330/120 ED
3/20
DXRE*J
SERIES 31
Drainage:
I = internal
E = external
Piloting:
I = internal
E = external
Proportional directional
valve with high-
response pilot
Option:
/ W7 = Zinc-nickel
surface treatment
Omit if not required.
(see par. 1.2)
Nominal size:
5R = ISO 4401-05
7 = ISO 4401-07
8 = ISO 4401-08
10 = ISO 4401-10
11 = ISO 4401-10 with oversize
ports
Spool type:
C = closed centre
A = open centre
Z = zero overlap
See par. 2 for operation and available flow rates.
D X R E - / 31 - -JH
K16 /
Digital integrated electronics
for closed loop with fieldbus
communication
Seals:
N = NBR seals for mineral oil (standard)
V = FPM seals for special fluids
Reference signal:
E0 = voltage ±10 V
E1 = current 4 ÷ 20 mA
FD = full digital version (on request)
Main connection 11 pin + PE
X4 Analogue transducer:
0 = none
1 = version 1
(single /double transducer)
X7 Digital transducer:
0 = none
1 = version 1 (SSI type)
2 = version 2 (Encoder type)
X1 Main connection configuration:
D1 = one command
D0 = full digital version (on request - available
for reference signal FD type only)
X2, X3 Fieldbus type:
CA = CAN Open
PD = PROFIBUS DP
EC = EtherCAT
EN = Ethernet /IP
PN = Profinet
PL = PowerLink
Series No.
(from 30 to 39 sizes and mounting dimensions remain
unchanged)
1.3 - Electronics with fieldbus communication
2 - COMPARISON AMONG INTEGRATED ELECTRONICS
dimensions in mm
1
Connection 6 pin + PE
X1 Main connection 11 pin + PE
X2 Fieldbus communication (IN)
X3 Fieldbus communication (OUT)
X4 Connection for analogue transducer
X7 Connection for digital transducer
NOTE 1: Depending on the chosen version, X4 and X7 connections may not be present.
Please refer to sections 5, 6 and 7 for connections descriptions and pinouts.
NOTE 2: Related mating connectors have to be ordered separately.
See catalogue 89 000.
J type JH type
85 330/120 ED
4/20
DXRE*J
SERIES 31
3 - AVAILABLE CONFIGURATIONS
The valve configuration depends on the combination of spool type and rated flow.
3 positions with spring centering
OFFSET POSITION for Z SPOOLS
After electrical swith-off or Enable signal swich-off (version K11A)
the main spool moves to springs offset position, with limited
opening (1%... 6% of main spool stroke in direction P- B / A-T)
valve type * Controlled flow with ∆p 10 bar P -T
DXRE5RJ 100 100 l/min
DXRE7J
120 120 l/min
220 220 l/min
DXRE8J
250 250 l/min
400 400 l/min
DXRE10J 800 800 l/min
DXRE11J 1000 1000 l/min
detailed symbol (spool Z)
85 330/120 ED
5/20
DXRE*J
SERIES 31
5 - DXRE*J - STANDARD ELECTRONICS
5.1 - Electrical characteristics
4 - ELECTRONICS COMMON DATA
Command signal: voltage (E0)
current (E1)
V DC
mA
±10 (Impedance Ri = 11 kOhm)
4 ÷ 20 (Impedance Ri = 58 Ohm)
Monitor signal (current to solenoid):
voltage (E0)
current (E1)
V DC
mA
±10 (Impedance Ro > 1 kOhm)
4 ÷ 20 (Impedance Ro = 500 Ohm)
Communication for diagnostic LIN-bus Interface (by means of the optional kit)
Connection 6 pin + PE (MIL-C-5015-G - DIN EN 175201-804)
Duty cycle 100% (continuous operation)
Protection class according to EN 60529 IP65 / IP67
Supply voltage V DC 24 (from 19 to 30 VDC), ripple max 3 Vpp
Power consumption VA 35
Maximum solenoid current A 2.6
Fuse protection, external A (fast), max current 4A
Managed breakdowns
Overload and electronics overheating, LVDT sensor error, cable
breakdown, supply voltage failures
Electromagnetic compatibility (EMC)
emissions EN 61000-6-4, immunity EN 61000-6-2
According to 2014/30/EU standards
5.2 - On-board electronics diagrams
VERSION C - 0V Monitor
VERSION A - External Enable VERSION B - Internal Enable
85 330/120 ED
6/20
DXRE*J
SERIES 31
5.3 - Version with voltage command (E0)
The reference signal must be between -10V and +10V. The monitor feature of versions B and C becomes available with a delay of 0.5 sec from
the power-on of the card.
5.4 - Version with current command (E1)
The reference signal is supplied in current 4 ÷ 20 mA. If the current for command is lower than 4 mA the card shows a breakdown cable error.
To reset the error is sufficient to restore the signal.
The monitor feature of versions B and C becomes available with a delay of 0.5 sec from the power-on of the card.
COMMAND -10V 0V +10V
MONITOR -10V 0V +10V
COMMAND 4 mA 12 mA 20 mA
MONITOR 4 mA 12 mA 20 mA
Pin Values version A version B version C
A
24 V DC
Supply Voltage
B
0 V
C
Enable do not connect PIN F reference
24 V DC - 0 V
D
± 10 V Command (differential input)
E
0 V Command reference
F
± 10 V Monitor (0V reference: pin B) Monitor
PE
GND Ground (Earth)
Pin Values version A version B version C
A
24 V DC
Supply Voltage
B
0 V
C
Enable do not connect PIN F reference
24 V DC - 0 V
D
4 ÷ 20 mA Command
E
0 V Command reference
F
4 ÷ 20 mA Monitor (0V reference: pin B) Monitor
PE
GND Ground (Earth)
85 330/120 ED
7/20
DXRE*J
SERIES 31
Pin Values Function
1
24 V DC
Main supply voltage
2
0 V
3
24V DC Enable
4
NC do not connect
5
NC do not connect
6
NC do not connect
7
NC do not connect
8
NC do not connect
9
24 V DC
Logic and control supply
10
0 V
11
24 V DC
Fault (0V DC) or normal
working (24V DC)
(0V ref. pin 2)
12
GND Ground (Earth)
6.2 - X1 Main connection pin table
D1: one command D0: full digital
6 - DXRE*JH - FIELDBUS ELECTRONICS
The 11+ PE pin connection allows separate supply voltage for electronics and solenoids.
Command - valve position schemes as for the standard electronics. Please refer to pictures in par. 5.3 and 5.4.
6.1 - Electrical characteristics
Command signal:
voltage (E0)
current (E1)
digital (FD)
V DC
mA
±10 (Impedance Ri = 11 kOhm)
4 ÷ 20 (Impedance Ri = 58 Ohm)
via fieldbus
Monitor signal (current to solenoid):
voltage (E0)
current (E1)
V DC
mA
±10 (Impedance Ro > 1 kOhm)
4 ÷ 20 (Impedance Ro = 500 Ohm)
Communication / diagnostic via Bus register
Communication interface standards
CAN Open
PROFIBUS DP
EtherCAT, Ethernet /IP, Profinet, PowerLink
EN 50325-4 + DS408
EN 50170-2 / IEC 61158
IEC 61158
Communication physical layer
CAN Open
PROFIBUS DP
EtherCAT, Ethernet /IP, Profinet, PowerLink
optical insulated CAN ISO 11898
optical insulated RS485
fast ethernet, insulated 100 Base TX
Power connection 11 pin + PE (DIN 43651)
Pin Values Function
1
24 V DC
Main supply voltage
2
0 V
3
24V DC Enable
4
± 10 V (E0)
4 ÷ 20 (E1)
Command
5
0 V
Command reference
signal
6
± 10 V (E0)
4 ÷ 20 (E1)
Monitor
(0V reference pin 10)
7
NC do not connect
8
NC do not connect
9
24 V DC
Logic and control supply
10
0 V
11
24 V DC
Fault (0V DC) or normal
working (24V DC)
(0V reference pin 2)
12
GND Ground (Earth)
85 330/120 ED
8/20
DXRE*J
SERIES 31
Pin Values Function
1
CAN_SH Shield
2
NC Do not connect
3
GND Signal zero data line
4
CAN_H Bus line (high)
5
CAN_L Bus line (low)
Pin Values Function
1
CAN_SH Shield
2
NC Do not connect
3
GND Signal zero data line
4
CAN_H Bus line (high)
5
CAN_L Bus line (low)
6.3 - FIELDBUS connections
Please wire following guidelines provided by the relative standards
communication protocol.
6.3.1 - Communication connection CA (CAN Open)
X2 (IN) connection: M12 A 5 pin female
X3 (OUT) connection: M12 A 5 pin male
Pin Values Function
1
+5 V Termination supply signal
2
PB_A Bus line (high)
3
0 V
Data line and termination
signal 0
4
PB_B Bus line (low)
5
SHIELD
Pin Values Function
1
+5 V Termination supply signal
2
PB_A Bus line (high)
3
0 V
Data line and termination
signal 0
4
PB_B Bus line (low)
5
SHIELD
6.3.2 - Communication connection PD (PROFIBUS DP)
X2 (IN) connection: M12 B 5 pin male (IN)
X3 (OUT) connection: M12 B 5 pin female
Pin Values Function
1
TX+ Transmitter
2
RX+ Receiver
3
TX- Transmitter
4
RX- Receiver
HOUSING shield
Pin Values Function
1
TX+ Transmitter
2
RX+ Receiver
3
TX- Transmitter
4
RX- Receiver
HOUSING shield
6.3.3 - Communication connections: EC (EtherCat), EN (Ethernet/IP), PN (PROFINET), PL (POWERLINK)
X2 (IN) connection M12 D 4 pin female X3 (OUT) connection: M12 D 4 pin female
NOTE: Shield connection on connector housing is
recommended.
85 330/120 ED
9/20
DXRE*J
SERIES 31
Pin SSI Values Function Notes
1
CLK+ Serial synchronous clock (+)
Input - digital signal
2
CLK- Serial synchronous clock (-)
3
MIS0+ Serial position data (+)
4
MIS0- Serial position data (-)
5
NC -
do not connect
6
NC -
7
+24 V transducer power supply Output power supply
8
0 V - Common GND
Pin Values Function Notes
1
ENC_Z+ input channel Z+
Input - digital signal
2
ENC_Z- input channel Z-
3
ENC_A+ input channel A+
4
ENC_A- input channel A+
5
ENC_B+ input channel B+
6
ENC_B- input channel B+
7
+5 V transducer power supply Output power supply
8
0 V - Common GND
6.4 - Digital transducer connection
X7 connection: M12 A 8 pin female
VERSION 1: SSI type
VERSION 2: ENCODER type
6.5 - Analogue transducer connection
X4 connection: M12 A 4 pin female
VERSION 1: single / double transducer
(single or double is a software-selectable option)
Pin Values Notes
1
+24 V Remote transducer power supply (out) 100 mA
2
±10 V
4 ÷20 mA
Input signal of transducer 1 (range software selectable)
3
0 V Common reference signal for transducer power and signals
4
±10 V
4 ÷20 mA
Input signal of transducer 2 (range software selectable)
5
-
85 330/120 ED
10/20
DXRE*J
SERIES 31
7 - CHARACTERISTIC CURVES
(with mineral oil with viscosity of 36 cSt at 50°C)
Typical flow rate curves at constant ∆p related to the reference signal and measured for the available spools.
The ∆p values are measured per land.
7.1 - Characteristic curves DXRE5RJ
SPOOL C100 / A100 SPOOL Z100
7.2 - Characteristic curves DXRE7J
SPOOL C120 / A120 SPOOL C220 / A220
SPOOL Z120 SPOOL Z220
offset position
offset position
offset position
85 330/120 ED
11/20
DXRE*J
SERIES 31
7.4 - Characteristic curves DXRE10J*
SPOOL C800 SPOOL Z800
SPOOL C400 / A400 SPOOL Z400
offset position
7.3 - Characteristic curves DXRE8J
SPOOL C250 / A250 SPOOL Z250
offset position
offset position
85 330/120 ED
12/20
DXRE*J
SERIES 31
8 - RESPONSE TIMES
(obtained with mineral oil with viscosity of 36 cSt at 50°C)
The tables shows the typical step response tested with static pressure 100 bar.
8.1 - DXRE5RJ
8.2 - DXRE7J
RESPONSE TIME FREQUENCY RESPONSE (spools type Z)
RESPONSE TIME FREQUENCY RESPONSE (spools type Z)
7.5 - Characteristic curves DXRE11J
SPOOL C1000 / A1000 SPOOL Z1000
offset position
85 330/120 ED
13/20
DXRE*J
SERIES 31
8.3 - DXRE8J
RESPONSE TIME FREQUENCY RESPONSE (spools type Z)
8.4 - DXRE10J and DXRE11J
RESPONSE TIME FREQUENCY RESPONSE (spools type Z)
85 330/120 ED
14/20
DXRE*J
SERIES 31
9 - HYDRAULIC CHARACTERISTICS
(with mineral oil with viscosity of 36 cSt at 50°C)
DXRE5RJ DXRE7J DXRE8J DXRE10J DXRE11J
Max flow rate l/min 180 450 900 1600 3500
Piloting flow requested with operation 0 →100% l/min 7 13 28 35 35
Piloting volume requested with operation 0 →100% cm
3
1.7 3.2 10 22 22
9.1 - Pilot and drain
The DXRE*J valves are available with pilot and drain both internal and external. The version with external drain allows a higher back pressure
on the discharge line.
PRESSURES (bar)
Pressure MIN MAX
Piloting pressure on X port 15 250
Pressure on T port with internal drain - 30
Pressure on T port with external drain - 250
TYPE OF VALVE
Plug assembly
X Y
IE
INTERNAL PILOT AND
EXTERNAL DRAIN
NO YES
II
INTERNAL PILOT
AND INTERNAL DRAIN
NO NO
EE
EXTERNAL PILOT
AND EXTERNAL DRAIN
YES YES
EI
EXTERNAL PILOT
AND INTERNAL DRAIN
YES NO
X: plug M5x6 for
external pilot
Y: plug M5x6 for
external drain
X: plug M6x8 for external pilot
Y: plug M6x8 for external drain
T
P
DXRE8J DXRE10J / DXRE11JDXRE7JDXRE5RJ
85 330/120 ED
15/20
DXRE*J
SERIES 31
NOTES:
See mounting surface at section 14.
- Do not dismantle the transducer.
- The valve is filled with mineral oil during
testing. the breathers on the pilot stage must
not be opened without specific authorization.
Breaking the seals may cause the loss of the
guarantee.
10 - OVERALL AND MOUNTING DIMENSIONS DXRE5RJ
dimensions in mm
1
Mounting surface with sealing rings:
5 OR type 2050 (12.42x1.78) - 90 Shore
1 OR type 2037 (9.25x1.78) - 90 Shore
2
Main connection
3
Electrical connector (to be ordered separately)
see paragraph 17
4 Air breather. Sealed at the factory (NOTES)
Valve fastening: N. 4 bolts M6x35 - ISO 4762
Tightening torque: 8 Nm (A8.8 screws)
Threads of mounting holes: M6x10
DXRE5RJH
85 330/120 ED
16/20
DXRE*J
SERIES 31
11 - OVERALL AND MOUNTING DIMENSIONS DXRE7J
dimensions in mm
Valve fastening: N. 4 bolts M10x60 - ISO 4762
N. 2 bolts M6x60 - ISO 4762
Tightening torque M10x60: 40 Nm (A8.8 screws)
M6x60: 8 Nm (A8.8 screws)
Threads of mounting holes: M6x18; M10x18
NOTES:
See mounting surface at section 14.
- Do not dismantle the transducer.
- The valve is filled with mineral oil during
testing. the breathers on the pilot stage must
not be opened without specific authorization.
Breaking the seals may cause the loss of the
guarantee.
1
Mounting surface with sealing rings.
4 OR type 130 (22.22X2.62) - 90 Shore
2 OR type 2043 (10.82x1.78) - 90 Shore
2
Main connection
3
Electrical connector (to be ordered separately)
see paragraph 17
4
Air breather. Sealed at the factory (NOTE)
DXRE7JH
85 330/120 ED
17/20
DXRE*J
SERIES 31
12 - OVERALL AND MOUNTING DIMENSIONS DXRE8J
Fastening of single valve: N. 6 bolts M12X60 - ISO 4762
Tightening torque: 69 Nm (A8.8 screws)
Threads of mounting holes: M12X20
NOTES:
See mounting surface at section 14.
- Do not dismantle the transducer.
- The valve is filled with mineral oil during
testing. the breathers on the pilot stage must
not be opened without specific authorization.
Breaking the seals may cause the loss of the
guarantee.
dimensions in mm
1
Mounting surface with sealing rings:
4 OR type 3118 (29.82x2.62) - 90 Shore
2 OR type 3081 (20.24x2.62) - 90 Shore
2
Main connection
3
Electrical connector (to be ordered separately)
see paragraph 17
4
Air breather. Sealed at the factory (NOTE)
DXRE8JH
85 330/120 ED
18/20
DXRE*J
SERIES 31
NOTES:
See mounting surface at section 14.
- Do not dismantle the transducer.
- The valve is filled with mineral oil during
testing. the breathers on the pilot stage must
not be opened without specific authorization.
Breaking the seals may cause the loss of the
guarantee.
13 - OVERALL AND MOUNTING DIMENSIONS DXRE10J / DXRE11J
1
Mounting surface with sealing rings:
DXRE10J
4 OR type 4150 (37.59x3.53) - 90 Shore
2 OR type 3081 (20.24x2.62) - 90 Shore
DXRE11J
4 OR type 4212 (53.57x3.53) - 90 Shore
2 OR type 3081 (20.24x2.62) - 90 Shore
2 Main connection
3
Electrical connector (to be ordered separately)
see paragraph 17
4 M12 eyebolt seat for safe lift
5 Air breather. Sealed at the factory (NOTE)
Valve fastening
: 6
SHC screws
ISO 4762 M20x70
Tightening torque: 330 Nm (A8.8 screws)
Threads of mounting holes: M20x40
dimensions in mm
DXRE10JH
85 330/120 ED
19/20
DXRE*J
SERIES 31
14 - MOUNTING SURFACES
54
62
50.8
y
P
B
facoltativo
M6
attacco "T"
Ø6.3 (max)
8
3.2
16.7
T
x
A
Ø11.2 (max)
37.3
27
46
32.5
21.4
11
6.3
88.1
101.6
65.9
76.6
50
34.1
Y
M10
ø
4
ø 6.3 (max)
BA
P
L
T
G
M6
X
G
18.3
ø
17.5 (max)
71.5
69.8
57.2
55.6
34.9
15.9
14.3
1.6
DXRE7J
ISO 4401-07-07-0-05
(CETOP 4.2-4-07-350)
130.2
112.7
G
ø 25 (max)
M12
P
B
Y
ø 7.5
53.2
29.4
17.5
5.6
L
X
G
ø 11.2 (max)
A
T
77
94.5
100.8
92.1
74.6
73
46
19
17.5
4.8
DXRE8J
ISO 4401-08-08-0-05
(CETOP 4.2-4-08-350)
DXRE5RJ
ISO 4401-05-05-0-05
(CETOP 4.2-4 R05-350)
190.5
168.3
Y
G
P
76.2
114.3
82.5
T
138.6
147.6
M20
Ø 32 (max)Ø 7.5
G
X
AB
41.3
Ø 11.2 (max)
158.8
130.2
123.8
44.5
35
DXRE10J
ISO 4401-10-09-0-05
(CETOP 4.2-4-10-350)
DXRE11J
ISO 4401-10-09-0-05
deviating from standard:
P, T, A, B ports Ø48
Optional
“T” port
85 330/120 ED
20/20
DXRE*J
SERIES 31
REPRODUCTION IS FORBIDDEN. THE COMPANY RESERVES THE RIGHT TO APPLY ANY MODIFICATIONS.
15 - HYDRAULIC FLUIDS
Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals. For fluids HFDR type
(phosphate esters) use FPM seals (code V). For the use of other kinds of fluid such as HFA, HFB, HFC, please consult our technical
department.
Using fluids at temperatures higher than 80 °C causes a faster degradation of the fluid and of the seals characteristics. The fluid must be
preserved in its physical and chemical characteristics.
16 - INSTALLATION
The valves can be installed in any position without impairing correct
operation. Make sure the hydraulic circuit is free of air.
Valves are fixed by means of screws or tie rods on a flat surface
with planarity and roughness equal to or better than those indicated
in the relative symbols. If minimum values are not observed, fluid
can easily leak between the valve and support surface.
Take care to the cleanliness of the mounting surfaces and
surrounding environment upon installation.
Surface finishing
DXRE7J DXRE8J
with rear ports PME07-AI6G -
with side ports PME07-AL6G PME5-AL8G
thread of ports: P - T - A - B
X - Y
1” BSP
1/4” BSP
1½” BSP
1/4” BSP
17 - ACCESSORIES
(to be ordered separately)
17.1 - Mating connectors
Mating connectors must be ordered separately. See catalogue 89 000.
We recommend the choice of a metal connector to avoid electromagnetic disturbances and to comply with EMC regulations on
electromagnetic compatibility. If you opt for a plastic connector, make sure that it guarantees and maintains the IP and EMC
protection characteristics of the valve.
17.2 - Mating connectors for fieldbus communication and for sensors.
Duplomatic offers spare parts to be wired and also ready-to-use cord sets. Please refer to cat. 89 000.
17.3 - Connection cable
The optimal wiring provides for 7 isolated conductors, with separate screen for the signal wires (command, monitor) and an overall screen.
Cross section for power supply:
- up to 20 m cable length : 1,0 mm
2
- up to 40 m cable length : 1,5 mm
2
Cross section for signals (command, monitor):
- 0,50 mm
2
17.4 - Kit for start-up LINPC-USB
Device for service start-up and diagnostic. See catalogue 89 850.
18 - SUBPLATES
(see catalogue 51 000)
Subplates are not available for DXRE5RJ, DXRE10J and DXRE11J.
