41 505/121 ED

1/28

41 505/121 ED

DS(P)*M

DIRECTIONAL VALVES

WITH SPOOL POSITION

MONITORING

OPERATING PRINCIPLE

DS3M DS5M

DSP5M

DSP5RM

DSP7M DSP8M DSP10M

Maximum operating pressure: P - A - B ports

bar

350 320 320 350 350 350

T port 210 see performance limits at paragraph 5.5

Maximum flow rate from P to A - B - T l/min 80 120 150 300 600 1100

Ambient temperature range °C -20 / +50

Fluid temperature range °C -20 / +80

Fluid viscosity range cSt 10 ÷ 400

Fluid contamination degree According to ISO 4406:1999 class 20/18/15

Recommended viscosity cSt 25

Mass: single solenoid valve

double solenoid valve

1,8

2,2

7,1

8,7

9,6

15,6

16,6

50.5

PERFORMANCES

(working with mineral oil of viscosity of 36 cSt at 50°C)

DS3M ISO 4401-03

DS5M ISO 4401-05

DSP5RM ISO 4401-05

DSP5M CETOP P05

DSP7M ISO 4401-07

DSP8M ISO 4401-08

DSP10M ISO 4401-10

— These solenoid operated directional valves are

equipped with position sensors that monitor the

main spool position. The switching position is

indicated by a binary signal.

— TÜV certification body certifies the compliance

of DS(P)*M valves with the EC safety standards

ISO 4413:2012, UNI EN 12622:2014, UNI EN

693:2001 +A2:2001, UNI EN 201:2010 and

UNI EN 422:2009 with certificate TÜV

IT 14 MAC 0043 .

— The valves are available in direct current

versions only (see paragraph 8).

— These valves do not have manual override and

can not be disassembled, because of their

characteristics and their possible use on

machinery subject to safety requirements.

Moreover, their components are not inter-

changeable. Read the Use and Maintenance

manual for instructions on operation, safe use

and repair of the product

41 505/121 ED

2/28

DS(P)*M

1 - IDENTIFICATION OF SOLENOID VALVES DIRECT OPERATED

1.1 - Identiﬁcation code

Monitoring of the spool position

Series No.

(the overall and mounting dimensions remain

unchanged from 20 to 29)

D S M - / 21 -

K1 /

Directional control valve

solenoid operated

3 = ISO 4401-03 size

5 = ISO 4401-05 size

Seals:

N = NBR seals for mineral oil (standard)

V = FPM seals for special fluids

Coil electrical connection:

plug for connector type

EN 175301-803 (ex DIN 43650)

Monitored position:

(see par. 16 for switching

logic)

R0 = monitored rest position

MA = monitored position ‘a’

MB = monitored position ‘b’

NOTE: Verify spool and sensor type availability in the tables below

DS3

SPOOLS

S* SA* SB*

TA100

TB100

SENSOR

TYPE

R0 x

MA x x x x

MB x x x x

DS5

SPOOLS

S* SA* SB*

TA100

TA02

TB02

TB100

SENSOR

TYPE

R0 x

MA x x x x x

MB x x x x x

MACHINE DIRECTIVE CERTIFICATION

All solenoid valves and solenoid operated valves of the DS(P)*M family were tested on a voluntary basis by TÜV

and found to comply with the applicable requirements of the following standards:

▪ UNI EN ISO 4413:2012 - Hydraulic fluid power – General rules and safety requirements for systems and their

components

▪ UNI EN 12622:2014 - Safety of machine tools - Hydraulic press brakes

▪ UNI EN 693:2001+A2:2011 - Machine tools – Safety – Hydraulic presses

▪ UNI EN 201:2010 - Plastics and rubber machines - Injection moulding machines - Safety requirements

▪ UNI EN 422:2009 - Rubber and Plastic machines – Safety requirements

Spool type (see par. 1.2)

S1 SA1 SB1 TA TB

S3 TA02 TB02

S4 SA4 SB4 TA100 TB100

NOTE: To be compliant with the EN 693:2011

standard, the valves have no manual override.

Position sensor supply

voltage:

Omit for 24V

12 = 12 V

(only available for monitored

position type M *)

DC power supply

D12 = 12 V

D24 = 24 V

D110 = 110 V

D220 = 220 V

41 505/121 ED

3/28

DS(P)*M

1.2 - Spool types for DS3M and DS5M

Type S*:

2 solenoids - 3 positions

with spring centering

Sensor R0

Type TA:

1 solenoid side A

2 external positions with return spring

Sensor MA Sensor MB

Type TB:

1 solenoid side B

2 external positions with return spring

Sensor MA Sensor MB

Type SA*:

1 solenoid side A

2 positions (central + external) with spring centering

Sensor MA Sensor MB

Type SB*:

1 solenoid side B

2 positions (central + external) with spring centering

Sensor MA Sensor MB

41 505/121 ED

4/28

DS(P)*M

2.3 - Performance limits for DS3M and DS5M solenoid valves

The curves define the flow rate operating fields according to the valve pressure of the different versions.

The values have been obtained according to ISO 6403 norm with solenoids at rated temperature and supplied with voltage equal to 90% of the

nominal voltage. The values have been obtained with mineral oil, viscosity 36 cSt, temperature 50 °C and filtration according to ISO 4406:1999

class 18/16/13.

The operating limits can be considerably reduced if a 4-way valve is used as 3-way valve with port A or B plugged or without flow.

SPOOL

CURVE

P→A P→B

S1,SA1 1 1

S3, 4 4

S4, SA4 2 2

TA, TB 1 1

TA100, TB100 3 3

SPOOL

CURVE

P→A P→B

S1 1 1

S3 3 3

S4 2 2

TA02 1 1

TA, TA100 1 1

DS5MDS3M

2.2 - DS5M - Pressure drops Δp-Q

2 - CHARACTERISTIC CURVES OF DIRECT OPERATED SOLENOID VALVES

(obtained with viscosity 36 cSt at 50 °C)

2.1 - DS3M - Pressure drops Δp-Q

SPOOL TYPE

FLOW DIRECTION

P→A P→B A→T B→T P→T

CURVES ON GRAPH

S1, SA1; SB1 2 2 3 3 -

S3 3 3 1 1 -

S4, SA4 5 5 5 5 3

TA, TB 2 2 2 2 -

TA100, TB100 4 4 4 4 -

SPOOL TYPE

FLOW DIRECTION

P→A P→B A→T B→T P→T

CURVES ON GRAPH

S1, SA1, SB1 2 2 1 1

S3 2 1 2 3

S4, SA4, SB4 1 1 2 2 4

TA, TB, TA02, TB02 3 3 2 2 -

TA100, TB100 2 2 2 2 -

For S3 in central position B→T refer to curve 3.

For S3 in central position B→T refer to curve 5.

41 505/121 ED

5/28

DS(P)*M

3 - OVERALL AND MOUNTING DIMENSIONS FOR DIRECT OPERATED VALVES

dimensions in mm

1 Mounting surface with sealing rings:

4 OR type 2037 (9.25x1.78)

90 Shore

2 Coil rotating 360°

3 Positioning sensor: setting sealed at

factory, do not tamper.

4 Connector for positioning sensor

type straight, molded.

To be ordered separately, see par.19

5 Coil electric connector

EN 175301-803 (ex DIN 43650)

to be ordered separately

cat. 49 000

Valve fastening: 4 SHC screws ISO 4762 M5x30

Tightening torque: 5 Nm (A8.8)

Threads of mounting holes: M5x10

2.4 - Switching times

The indicated values had obtained according to ISO 6403 standards, using mineral oil with viscosity 36 cSt at 50 °C.

TIMES [ms] ENERGIZING DE-ENERGIZING

DS3M 25 ÷ 75 15 ÷ 25

TIMES [ms] ENERGIZING DE-ENERGIZING

DS5M 100 ÷ 150 20 ÷ 50

DS3M-S*

DS3M-TA

DS3M-TA*

DS3M-SA*

DS3M-TB

DS3M-TB*

DS3M-SB*

sensor

type:

sensor type:

41 505/121 ED

6/28

DS(P)*M

dimensions in mm

Valve fastening: 4 SHC screws ISO 4762 M6x40

Tightening torque: 8 Nm

Threads of mounting holes: M6x10

DS5M-TA

DS5M-TA*

DS5M-S*

DS5M-TB

DS5M-TB*

1 Mounting surface with

sealing rings.

5 OR type 2050

(12.42x1.78) - 90 Shore

2 Coil rotating 360°

3 Positioning sensor:

setting sealed at factory,

do not tamper.

4 Connector for positioning

sensor type straight,

molded.

To be ordered separately,

see par. 19

5 Coil electric connector

EN 175301-803 (ex DIN

43650) to be ordered

separately cat. 49 000

sensor type:

sensor

type:

41 505/121 ED

7/28

DS(P)*M

Size:

5 = CETOP P05

5R = ISO 4401-05

7 = ISO 4401-07

8 = ISO 4401-08

10 = ISO 4401-10

P = Subplate with restrictor on port P placed

under the pilot valve

(omit for valves with piloting type Z and for valves

with option D - control of the shifting speed of the

main spool)

D = shifting speed of the main spool (see par. 7)

Directional valve,

Solenoid controlled

Pilot operated

Spool type (see paragraph 4.2)

S1 SA1 SB1 TA TB

S3 TA100 TB100

Series:

10 = for DSP5M, DSP5RM and DSP8M

20 = for DSP7M

30 = for DSP10M

(the overall and mounting dimensions within the

same ten remain unchanged)

Seals:

N = NBR seals for mineral oil (standard)

V = FPM seals for special fluids

Drainage (see paragraph 6):

I = Internal

E = External

Piloting (see paragraph 6):

I = internal (not available for S4 spool)

E = external

C = internal piloting with backpressure valve

(available on DSP7 and DSP8 only)

Z = internal piloting with 30 bar fixes adjustment pressure reducing

valve (see par. 5.5)

D S

M / / /- / -

Monitoring of the spool position

DC power supply

D12 = 12 V

D24 = 24 V

D110 = 110 V

D220 = 220 V

Coil electrical connection:

plug for connector type DIN 43650

Monitored position:

(see par. 16 for switching logic)

1 positioning sensor

R0 = rest position monitored

MA = position ‘a’ monitored

MB = position ‘b’ monitored

2 positioning sensor

M0 = rest position monitored

MAB = ‘a’ and ‘b’ positions

monitored

NOTE: To be compliant with the EN 693:2011

standard, the valves have no manual

override.

NOTA: Verify spool and sensor type availability in the table below

NOTE: DSP10M available with spools S1 or S4, with monitored

position R0 or M0 only.

SPOOLS

SA*

SB*

TA100

TB100

SENSOR TYPE

R0 x

MA x x x x

MB x x x x

M0 x

MAB x x x x

4 - IDENTIFICATION OF PILOT OPERATED SOLENOID VALVES

4.1 - Identiﬁcation code

Position sensor supply

voltage: Omit for 24V

12 = 12 V

(only available for

monitored position

type M *)

41 505/121 ED

8/28

DS(P)*M

4.2 - Spool types for DSP5M, DSP5RM, DSP7M and DSP8M

Type S*:

2 solenoids - 3 positions with spring centering

sensor R0 sensor M0 sensor MAB

sensor MA sensor MB sensor MAB

sensor MA sensor MB

Type TA:

1 solenoid side A

2 external positions

with return spring

Type TB:

1 solenoid side B

2 external positions

with return spring

Type SA*:

1 solenoid side A

Type SB*:

1 solenoid side B

2 positions

(central + external)

with spring centering

Type RK:

2 solenoids - 2 positions

with mechanical detent

41 505/121 ED

9/28

DS(P)*M

5 - CHARACTERISTIC CURVES AND PERFORMANCES

(values obtained with viscosity 36 cSt at 50 °C)

5.1 - DSP5M and DSP5RM - Pressure drops Δp-Q

5.2 - DSP7M - Pressure drops Δp-Q

5.3 - DSP8M - Pressure drops Δp-Q

SPOOL TYPE

FLOW DIRECTION

P→A P→B A→T B→T P→T

CURVES ON GRAPH

S1, SA1 4 4 1 1 -

S3 4 4 1 1 -

S4 5 5 2 3 5

TA, TB 4 4 1 1 -

TA100, TB100 3 3 1 1 -

RK 4 4 1 1 -

SPOOL TYPE

FLOW DIRECTION

P→A P→B A→T B→T P→T

CURVES ON GRAPH

S1, SA1 1 1 4 5 -

S3 1 1 5 5 -

S4 2 2 5 6 5

TA, TB 1 1 4 5 -

TA100, TB100 3 3 3 5 -

RK 1 1 4 5 -

SPOOL TYPE

FLOW DIRECTION

P→A P→B A→T B→T P→T

CURVES ON GRAPH

S1, SA1 2 2 3 3 -

S3 2 2 2 1 -

S4 4 4 3 5 6

TA, TB 2 2 3 3 -

TA100, TB100 5 5 5 5 -

RK 2 2 3 3 -

For pressure drops of the S3 spool in central position refer to the

curve 4.

For pressure drops of the S3 spool in central position refer to the

curve 5.

For pressure drops of the S3 spool in central position refer to the

curve 4.

41 505/121 ED

10/28

DS(P)*M

5.5 - Performance limits for pilot operated valves

5.6 - Switching times

The values indicated refer to a solenoid valve working with piloting

pressure of 100 bar, with mineral oil at a temperature of 50°C, at

viscosity of 36 cSt and with PA and BT connections.

The energizing and de-energizing times are obtained at the

pressure variation which occurs on the lines.

TIMES (± 10%)

[ms]

ENERGIZING DE-ENERGIZING

2 Pos. 3 Pos. 2 Pos. 3 Pos.

DSP5M - DSP5RM 60 50 50 40

DSP7M 75 60 60 45

DSP8M 100 70 80 50

DSP10M - 100 - 140

MAXIMUM FLOW RATES

DSP5M

DSP5RM

DSP7M DSP8M DSP10M

Spool type

PRESSURES

210 bar 320 bar 210 bar 350 bar 210 bar 350 bar 210 bar 350 bar

S4 - TA100

[l/min]

120 100 200 150 500 450 750 600

S1 - S3 - TA - RK 150 120 300 300 600 500 900 700

NOTE 1: minimum piloting pressure can be the lower range value at low flows rates, but with higher flow rates the higher value is needed.

NOTE 2: if the valve operates with higher pressures it is necessary to use the version with external pilot and reduced pressure. Otherwise, the

valve with internal pilot and pressure reducing valve with 30 bar fixed adjustment can be ordered.

Add the letter Z to the identification code to order this option (see par. 4.1).

PRESSURES

DSP5M

DSP5RM

DSP7M DSP8M DSP10M

Max pressure in P, A, B ports 320 350 350 350

Max pressure in T line 210 210 210 210

Max pressure in Y line 210 210 210 210

Min piloting pressure NOTE 1 5 ÷ 10 5 ÷ 12 7 ÷ 14 6 ÷ 12

Max piloting pressure NOTE 2 210 210 210 280

5.4 - DSP10M - Pressure drops Δp-Q

SPOOL TYPE

FLOW DIRECTION

P→A P→B A→T B→T P→T

CURVES ON GRAPH

S1 1 1 1 1 -

S4 2 2 2 2 -

41 505/121 ED

11/28

DS(P)*M

The curve refers to the pressure drop (body part

only) with backpressure valve inside, to which

the pressure drop of the reference spool must be

added. (see par. 5)

DSP8MDSP7M

X: plug M5x6 for external pilot

Y: plug M5x6 for external drain

6 - PILOTING AND DRAINAGE

These valves are available with piloting and drainage, both internal and

external. The version with external drainage allows for a higher back pressure

on the outlet.

TYPE OF VALVE

Plug assembly

X Y

internal pilot and

external drain

NO YES

Internal pilot and

internal drain

NO NO

external pilot and

external drain

YES YES

external pilot and

internal drain

YES NO

6.1 - Backpressure valve incorporated on line P (C option)

DSP7M and DSP8M valves are available upon request with backpressure valve incorporated on line P. This is necessary to obtain the piloting

pressure when the control valve, in rest position, has the line P connected to the T port (spools S4).

The cracking pressure is of 5 bar with a minimum flow rate of 15 l/min.

In the C version the piloting is always internal.

NOTE: the backpressure valve can’t be used as check valve because it doesn’t assure the seal.

Add C to the identification code for this request (see paragraph 4.1).

For DSP7M only, the backpressure valve can be also delivered separately and it can be easily mounted on line

P of the main control valve. Ask for code 0266577 to order the backpressure valve.

pilot always internal

Y: plug M6x8 for external drain

DSP8M DSP10MDSP7MDSP5M

DSP5RM

X: plug M6x8 for external pilot

Y: plug M6x8 for external drain

41 505/121 ED

12/28

DS(P)*M

Suffix

Nominal

voltage

[V]

Resistance

at 20°C

[Ω]

Current

consumpt.

[A]

Power

consumpt

[W]

Coil

code

D12 12 4,4 2,72 32,7 1903080

D24 24 18,6 1,29 31 1903081

D110 110 436 0,26 28,2 1903464

D220 220 1758 0,13 28,2 1903465

Suffix

Nominal

voltage

[V]

Resistance

at 20°C

[Ω]

Current

consumpt.

[A]

Power

consumpt

[W]

Coil

code

D12 12 3 4 48 1903550

D24 24 12 2 48 1903551

D110 110 252 0,44 48 1903554

D220 220 1010 0,22 48 1903555

DS3M, DSP5M, DSP5RM, DSP7M, DSP8M and DSP10M

(values ± 10%)

DS5M (values ± 5%)

VOLTAGE SUPPLY FLUCTUATION

± 10% Vnom

MAX SWITCH ON FREQUENCY

DS3M

DS5M

DSP5M - DSP5RM

DSP7M

DSP8M

DSP10M

15.000 ins/hr

13.000 ins/hr

5.000 ins/hr

4.000 ins/hr

3.000 ins/hr

DUTY CYCLE

100%

ELECTROMAGNETIC COMPATIBILITY

(EMC) (NOTE 1)

In compliance with

2014/30/EU

LOW VOLTAGE

In compliance with

2014/35/EU

CLASS OF PROTECTION:

Atmospheric agents (IEC 60529)

Coil insulation (VDE 0580)

Impregnation

IP65 (NOTE 2)

class H

class F

8 - ELECTRICAL FEATURES

8.1 - Solenoids

These are essentially made up of two parts: tube and coil. The tube

is threaded into the valve body and includes the armature that

moves immersed in oil, without wear. The inner part, in contact with

the oil in the return line, ensures heat dissipation.

The coil is fastened to the tube by a threaded ring, and can be

rotated and locked to suit the available space.

NOTE 1 : In order to further reduce the emissions, use of type H

connectors is recommended. These prevent voltage peaks on

opening of the coil supply electrical circuit (see catalogue 49 000).

NOTE 2: The IP65 protection degree is intended for the whole

valve. It is guaranteed only with valve and connectors correctly

connected and installed.

8.2 - Current and absorbed power

The tables shows current and power consumption values relevant

to the different coil types for DC.

7 - OPTIONS

7.1 - Option D : control of the main spool shifting speed

By placing a MERS type double flow control valve between the pilot solenoid valve and

the hydropiloted valve, the piloted flow rate can be controlled and therefore the change

over smoothness can be varied.

Add the letter D to the identification code to request this device (see paragraph 4.1).

dimensions in mm

DSP5 DSP7 DSP8 DSP10

A 218 225 254 307

9 - COIL CONNECTORS

The solenoid operated valves are delivered without the connectors. They can be ordered separately.

For the identification of the connector type to be ordered, please see catalogue 49 000.

41 505/121 ED

13/28

DS(P)*M

10 - DSP5M AND DSP5RM OVERALL AND MOUNTING DIMENSIONS

dimensions in mm

DSP5M-S*

DSP5RM-S*

Valve fastening: 4 SHC screws ISO 4762 M6x35

Tightening torque: 8 Nm (screws A 8.8)

Threads of mounting holes: M6x10

1 Mounting surface with sealing rings

5 OR type 2050 (12.42x1.78) - 90 Shore

2 OR type 2037 (9.25x1.78) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type . To be ordered separately

see cat. 49 000

sensor type:

MAB

sensor type:

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

14/28

DS(P)*M

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

dimensions in mm

DSP5M-TA, TA100, SA1

DSP5RM-TA, TA100, SA1

Solenoid position

for TB and SB*

versions

sensor type:

MAB

sensor type:

Solenoid position

for TB and SB*

versions

sensor position

for TB and SB*

versions

1 Mounting surface with sealing rings

5 OR type 2050 (12.42x1.78) - 90 Shore

2 OR type 2037 (9.25x1.78) - 90 Shore

2 Position sensor: set and sealed at factory,

do not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type. To be ordered separately

see cat. 49 000

41 505/121 ED

15/28

DS(P)*M

1 Mounting surface with sealing rings

5 OR type 2050 (12.42x1.78) - 90 Shore

2 OR type 2037 (9.25x1.78) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type. To be ordered separately

see cat. 49 000

dimensions in mm

DSP5M-RK

DSP5RM-RK

sensor type:

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

16/28

DS(P)*M

11 - DSP7M OVERALL AND MOUNTING DIMENSIONS

dimensions in mm

DSP7M-S*

sensor type:

MAB

sensor type:

Valve fastening: 4 SHC screws ISO 4762 M10x60

2 SHC screws ISO 4762 M6x50

Tightening torque: M10x60: 40 Nm

M6x50: 8 Nm

Threads of mounting holes: M6x18; M10x18

1 Mounting surface with sealing rings.

4 OR type 130 (22.22x2.62) - 90 Shore

2 OR type 2043 (10.82x1.78) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type. To be ordered separately

see cat. 49 000

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

17/28

DS(P)*M

dimensions in mm

DSP7M-TA, TA100, SA1

Solenoid position

for TB and SB*

versions

sensor type:

MAB

sensor type:

Solenoid position

for TB and SB*

versions

sensor position

for TB and SB*

versions

1 Mounting surface with sealing rings.

4 OR type 130 (22.22x2.62) - 90 Shore

2 OR type 2043 (10.82x1.78) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type. To be ordered separately

see cat. 49 000

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

18/28

DS(P)*M

dimensions in mm

DSP7M-RK

sensor type:

1 Mounting surface with sealing rings.

4 OR type 130 (22.22x2.62) - 90 Shore

2 OR type 2043 (10.82x1.78) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type. To be ordered separately

see cat. 49 000

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

19/28

DS(P)*M

12 - DSP8M OVERALL AND MOUNTING DIMENSIONS

dimensions in mm

Valve fastening: 6 SHC screws ISO 4762 M12x60

Tightening torque: 69 Nm

Threads of mounting holes: M12x20

DSP8M-S*

sensor type:

MAB

sensor type:

1 Mounting surface with sealing rings.

4 OR type 3118 (29.82x2.62) - 90 Shore

2 OR type 3081 (20.24x2.62) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type. To be ordered separately

see cat. 49 000

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

20/28

DS(P)*M

dimensions in mm

DSP8M-TA, TA100, SA1

Solenoid position

for TB and SB*

versions

sensor type:

MAB

sensor type:

Solenoid position

for TB and SB*

versions

sensor position

for TB and SB*

versions

1 Mounting surface with sealing rings.

4 OR type 3118 (29.82x2.62) - 90 Shore

2 OR type 3081 (20.24x2.62) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803 (ex

DIN 43650) type. To be ordered separately

see cat. 49 000

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

21/28

DS(P)*M

dimensions in mm

DSP8M-RK

sensor type:

MAB

1 Mounting surface with sealing rings.

4 OR type 3118 (29.82x2.62) - 90 Shore

2 OR type 3081 (20.24x2.62) - 90 Shore

2 Position sensor: set and sealed at factory, do

not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil electric connector EN 175301-803

(ex DIN 43650) type

To be ordered separately see cat. 49 000

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

41 505/121 ED

22/28

DS(P)*M

13 - DSP10M OVERALL AND MOUNTING DIMENSIONS

dimensions in mm

DSP10M-S*

sensor type:

1 Mounting surface with sealing rings.

4 OR type 4150 (37.59x3.53) - 90 shore

2 OR type 3081 (20.24x2.62) - 90 shore

2 Positioning sensor : setting sealed at

factory, do not tamper.

3 Connector for positioning sensor, type

straight, molded.

To be ordered separately, see par. 19

4 Coil connector EN 175301-803 (ex

DIN 43650) type. - To be ordered

separately see cat. 49 000

NOTE: for overall dimensions with Z option (fixed adjustment

pressure reducing valve) consider an increase of 30 mm in height.

Valve fastening

: 6

SHC screws

ISO 4762 M20x70

Tightening torque: 330 Nm (A8.8 screws)

Threads of mounting holes: M20x40

490

41 505/121 ED

23/28

DS(P)*M

50.8

37.3

3.2

16.7

M6x10

facoltativo

Attacco "T"

Ø11.2 (max)

32.5

21.4

6.3

14 - MOUNTING SURFACES

DS3M

ISO 4401-03-02-0-05

(CETOP 4.2-4-03-350)

Ø6.3 (max)

attacco "T"

facoltativo

65.1

50.8

37.3

11.1

3.2

16.7

Ø11.2 (max)

43.6

32.5

21.4

6.3

2.4

50.8

facoltativo

attacco "T"

Ø6.3 (max)

3.2

16.7

Ø11.2 (max)

37.3

32.5

21.4

6.3

DSP5M

CETOP 4.2-4 P05-320

DSP5RM

ISO 4401-05-05-0-05

(CETOP 4.2-4 R05-320)

101.6

88.1

76.6

65.9

34.1

Ø4

M10

Ø6.3 (max)

18.3

Ø17.5 (max)

71.5

69.8

57.2

55.6

34.9

15.9

14.3

1.6

DSP7M

ISO 4401-07-07-0-05

(CETOP 4.2-4-07-350)

DS5M

ISO 4401-05-04-0-05

(CETOP 4.2-4-05-320)

130.2

112.7

Ø25 (max)

M12

Ø7.5

53.2

29.4

17.5

5.6

Ø11.2 (max)

94.5

100.8

92.1

74.6

17.5

4.8

DSP8M

ISO 4401-08-08-0-05

(CETOP 4.2-4-08-350)

Optional

port ‘T’

Optional

port ‘T’

Optional

port ‘T’

41 505/121 ED

24/28

DS(P)*M

15 - POSITIONING SENSORS

WARNING ! The disassembly of the valve is not

allowed. The sensors must not be unscrewed or

tampered with in any way.

The M0 and MAB versions have two positioning sensors; consider

that the connection scheme shown must be done for each sensor.

ELECTRICAL CHARACTERISTICS

Operating voltage range

24 V DC

12 V DC

V DC

20 ÷ 32

10.5 ÷ 16

Absorbed current A 0.4

Max output load mA 400

Output 2 PNP

Electric protections

polarity inversion

short circuit

Hysteresis mm ≤ 0.1

Operating temperature range °C - 25 / +80

Class of protection from

atmospheric agents

(IEC 60529)

IP65

EMC

Electromagnetic compatibility

In compliance with

2014/30/EU

R0 CONNECTION SCHEME

M* CONNECTION SCHEME

Pin Values Function

1 +24 V Supply

2 NC Normal Closed -

3 0 V -

4 NC Normal Closed +

Pin Values Function

1 +24 V Supply

2 NC Normal Closed

3 0 V -

4 NO Normal Open

190.5

168.3

76.2

114.3

82.5

138.6

147.6

M20

Ø 32 (max)Ø 7.5

41.3

Ø 11.2 (max)

158.8

130.2

123.8

44.5

DSP10M

ISO 4401-10-09-0-05

(CETOP 4.2-4-10-350)

Pin Values Function

1 +12 V Supply

2 NC Normal Closed

3 0 V -

4 NO Normal Open

M*12 CONNECTION SCHEME

12 V

41 505/121 ED

25/28

DS(P)*M

spiega sul monitoraggio???

16.2 - MA monitoring

Energized position monitored with one positioning sensor.

Available on both direct and pilot operated valves;

spool type SA*, TA, TA02, TA100

De-energized position monitored with one positioning sensor.

Available on both direct and pilot operated valves;

spool type SB*, TB, TB02, TB100

16 - SWITCHING LOGICS

Duplomatic offers a wide range of available positions to be monitored, and for the pilot operated valve there are even monitorning with

redundant signal.

16.1 - R0 monitoring

Central position monitored with one positioning sensor.

Available on both direct and pilot operated valves;

spool type S*

Position ‘a’ monitored with one positioning sensor.

Available on pilot operated valves only;

spool type RK

41 505/121 ED

26/28

DS(P)*M

16.4 - M0 monitoring

Central position monitored by two separate positioning sensors.

Available on pilot operated valves only;

spool type S*

Sensor

side “A”

Sensor

side “B”

16.3 - MB monitoring

De-energized position monitored with one positioning sensor.

Available on both direct and pilot operated valves;

spool type SA*, TA, TA02, TA100

Energized position monitored with one positioning sensor.

Available on both direct and pilot operated valves;

spool type SB*, TB, TB02, TB100

Position ‘b’ monitored with one positioning sensor.

Available on pilot operated valves only;

spool type RK

17 - HYDRAULIC FLUIDS

Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals (code N). For fluids HFDR type

(phosphate esters) use FPM seals (code V). For the use of other fluid types such as HFA, HFB, HFC, please consult our technical department.

Using fluids at temperatures higher than 80 °C causes a faster degradation of the fluid and of the seals characteristics. The fluid must be

preserved in its physical and chemical characteristics.

18 - INSTALLATION

WARNING ! These valves must be installed and commissioned by qualified personnel

only. Before starting any installation, commissioning or maintenance is mandatory read

the manual of use and maintenance, delivered together with the valve.

Configurations with centering and recall springs can be mounted in any position; The RK versions,

without springs and with mechanical detent, must be mounted with the longitudinal axis horizontal.

Valve fastening takes place by means of screws or tie rods, laying the valve on a lapped surface, with

values of planarity and smoothness that are equal to or better than those indicated in the drawing.

If the minimum values of planarity or smoothness are not met, fluid leakages between valve and

mounting surface can easily occur.

41 505/121 ED

27/28

DS(P)*M

16.5 - MAB monitoring

Both external positions monitored by two separate positioning

sensors.

Available on pilot operated valves only;

spool type S*

De-energized position monitored on side A.

Energized position monitored on side B.

Available on pilot operated valves only;

spool type SA1, TA, TA100

Energized position monitored on side A.

De-energized position monitored on side B.

Available on pilot operated valves only;

spool type SB1, TB, TB100

Sensor

side “A”

Sensor

side “B”

Sensor

side “A”

Sensor

side “B”

Sensor

side “A”

Sensor

side “B”

Surface finishing

19 - SENSOR CONNECTORS

The female connectors for position switches can be ordered separately, by specifying the descriptions here below, depending on the desired type.

The IP protection degree indicated below is valid only with the connector correctly tightened on the relative counter-piece.

41 505/121 ED

28/28

DS(P)*M

REPRODUCTION IS FORBIDDEN. THE COMPANY RESERVES THE RIGHT TO APPLY ANY MODIFICATIONS.

DS3M DS5M DSP5M DSP7M DSP8M

Type with rear ports PMMD-AI3G PMD4-AI4G PME4-AI5G PME07-AI6G -

Type with side ports PMMD-AL3G PMD4-AL4G PME4-AL5G PME07-AL6G PME5-AL8G

P, T, A, B ports dimensions

X, Y ports dimensions

3/8” BSP

3/4” BSP (PMD4-AI4G)

1/2” BSP (PMD4-AL4G)

3/4” BSP

1/4” BSP

1” BSP

1/4” BSP

1 ½” BSP

1/4” BSP

20 - SUBPLATES

(see catalogue 51 000)

description: ECM4S/M12L/10/L5 code: 3491000008

right connector molded cable pre-wired M12x1

4 poles, female, IP67, IP68, IP69K

cable: Ø 4.7 mm; lenght 5 mt;

conductor: section 0.34 mm²

cable material polyurethane resin (oil resistant)

LED no

description : ECM4S/M12S/10/L5 code: 3491000009

angle connector pre-wired M12x1 with molded cable

4 poles, female, IP67, IP68, IP69K

cable: Ø 4.7 mm; lenght 5 mt;

conductor: section 0.34 mm²

cable material polyurethane resin (oil resistant)

LED no

Wire colors for connectors ECM4*

description : EC4S/M12S/10 code: 3491001002

circular connector M12 with screw locking, angular, to wire.

4 poles, female, IP67

ref. norm: IEC 61076-2-101 (Ed. 1) / IEC 60947-5-2

cable gland: PG7

cable: Ø 4 ÷ 6 mm

conductors: max 0.75 mm²

contacts: a vite

Case material polyamide (nylon)

LED no

1 BN brown

2 WH white

3 BU blue

4 Bk black