41 155/119 ED
1/8
41 155/119 ED
DS3B
SOLENOID ACTUATED
DIRECTIONAL VALVE,
DIRECT OPERATED
SERIES 10
MOUNTING INTERFACE
ISO 4401-03-02-0-05
(CETOP 4.2-4-03-350)
— Solenoid actuated directional control valve, direct
operated with mounting surface according to ISO
4401-03 standards.
— The valve is supplied with 3 or 4 ways design, 2 or 3
positions, with a wide range of spools.
— The valve body is made with high strength iron castings
provided with wide internal paths in order to minimize
the flow pressure drop. Wet armature solenoids with
interchangeable coils are used (for further
information on solenoids see par. 7).
— The valve is available with DC solenoids.
— The valve is also available with zinc-nickel
coating that ensures a salt spray resistance up to
120 hours.
OPERATING PRINCIPLE
SUBPLATE MOUNTING
ISO 4401-03
p max 320 bar
Q max 60 l/min
Maximum operating pressure:
- P - A - B ports
- T port
bar
320
250
Maximum flowrate l/min 60
Pressure drops ∆p-Q see paragraph 4
Operating limits see paragraph 5
Electrical features see paragraph 7
Electrical connections EN 175301-803 (ex DIN 43650)
Ambient temperature range °C -20 / +50
Fluid temperature range °C -20 / +80
Fluid viscosity range cSt 10 ÷ 400
Fluid contamination degree
according to ISO 4406:1999
class 20/18/15
Recommended viscosity cSt 25
Mass: single solenoid valve
double solenoid valve
kg
1,4
2
PERFORMANCES
(obtained with mineral oil with viscosity of 36 cSt at 50°C)
41 155/119 ED
2/8
DS3B
SERIES 10
1 - IDENTIFICATION CODE
Directional valve,
solenoid operated
ISO 4401-03 size
Spool type (see paragraph 3)
DC power supply
SD12 = 12 V
SD24 = 24 V
SD00 = valve without coils (see NOTE 1)
Series:
(the overall and mounting dimensions remain
unchanged from 10 to 19)
Coil electrical connection
(see par. 10):
K1 = plug for connector type
EN 175301-803 (ex DIN 43650)
(standard)
K7 = plug DEUTSCH DT04-2P for male
connector type DEUTSCH DT06-2S
Seals:
N = NBR seals for mineral oil (standard)
V = FPM seals for special fluids
D S 3 B -
/
10 -
/
2 - HYDRAULIC FLUIDS
Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals (code N). For fluids HFDR type
(phosphate esters) use FPM seals (code V). For the use of other fluid types such as HFA, HFB, HFC, please consult our technical department.
Using fluids at temperatures higher than 80 °C causes a faster degradation of the fluid and of the seals characteristics. The fluid must be
preserved in its physical and chemical characteristics.
Manual override:
omit for override integrated in the tube
(standard) (see par. 12)
CM = manual override, boot protected
Option:
/ W7 = Zinc-nickel surface
treatment (see NOTE 2)
Omit if not required
S*
SA*
SB*
TA
TB
TA*
TB*
RK
NOTE 1: Coils locking ring and related OR are supplied together with the valves.
NOTE 2: The standard valve is supplied with surface treatment of phosphating black.
The zinc-nickel finishing on the valve body makes the valve suitable to ensure a salt spray resistance up to 120 hours.
(test operated according to UNI EN ISO 9227 standards and test evaluation operated according to UNI EN ISO 10289 standards).
41 155/119 ED
3/8
DS3B
SERIES 10
3 - SPOOL TYPE
Type S*:
2 solenoids - 3 positions
with spring centering
Type SA*:
1 solenoid side A
2 positions (central + external)
with spring centering
Type SB*:
1 solenoid side B
2 positions (central + external)
with spring centering
Type TA:
1 solenoid side A
2 external positions
with return spring
Type TB:
1 solenoid side B
2 external positions
with return spring
Type RK:
2 solenoids - 2 positions
with mechanical retention
SPOOL TYPE
FLOW DIRECTION
P→A P→B A→T B→T P→T
CURVES ON GRAPH
S2, SA2, SB2 1
S3, SA3, SB3 3 3
S4, SA4, SB4 3
S5 5
S6 3
S7, S8 6 6 3
S10 3 3
S11 3
S18 5
41 155/119 ED
4/8
DS3B
SERIES 10
DE-ENERGIZED POSITION
ENERGIZED POSITION
5 - SWITCHING TIMES
The values indicated are obtained according to ISO 6403 standard,
with mineral oil viscosity 36 cSt at 50°C.
Please refer to curve no. 4 for pressure drops between A and B
lines of the S10 spool when used in regenerative circuits.
4 - PRESSURE DROPS ∆p-Q
(obtained with viscosity 36 cSt at 50 °C)
TIMES [ms]
ENERGIZING DE-ENERGIZING
25 ÷ 75 15 ÷ 25
SPOOL TYPE
FLOW DIRECTION
P→A P→B A→T B→T
CURVES ON GRAPH
S1, SA1, SB1 1 1 3 3
S2, SA2, SB2 2 2 3 3
S3, SA3, SB3 3 3 2 2
S4, SA4, SB4 4 4 4 4
S5 1 2 3 3
S6 1 1 3 2
S7, S8 5 4 4 4
S9 1 1 3 3
S10 2 3 2 3
S11 1 1 2 3
S12 1 1 3 3
S18 2 1 3 3
TA, TB 3 3 3 3
TA02, TB02 1 1 1 1
TA23, TB23 3 3
RK 1 1 1 1
1
2
41 155/119 ED
5/8
DS3B
SERIES 10
6 - OPERATING LIMITS
The curves define the flow rate operating fields according to the valve pressure of the different versions. The values have been obtained
according to ISO 6403 norm with solenoids at rated temperature and supplied with voltage equal to 90% of the nominal voltage. The value
have been obtained with mineral oil, viscosity 36 cSt, temperature 50 °C and filtration according to ISO 4406:1999 class 18/16/13.
The limits have been verified with standard 4-way valve. Performance can be considerably reduced if a 4-way valve is used as 3-way, with port
A or B plugged or without flow.
SPOOL
CURVE
P→A P→B
S1,SA1,SB1 1 1
S2, SA2, SB2 2 2
S3, SA3, SB3 3 3
S4, SA4, SB4 4 4
S5 1 1
S6 1 5
S7 1 1
S8 1 1
S9 1 1
S10 1 1
S11 1 5
S12 1 1
S18 1 1
SPOOL
CURVE
P→A P→B
TA, TB 1 1
TA02, TB02 1 1
TA23, TB23 1 1
RK 1 1
7 - ELECTRICAL FEATURES
7.1 - Solenoids
These are essentially made up of two parts: tube and coil. The tube
is threaded into the valve body and includes the armature that
moves immersed in oil, without wear. The inner part, in contact with
the oil in the return line, ensures heat dissipation. The coil is
fastened to the tube by a threaded ring, and can be rotated 360°, to
suit the available space.
7.2 - Current and absorbed power
The table shows current and power consumption
values of the DC coils.
Coils for direct current (values ± 10%)
Nominal
voltage
[V]
Resistance
at 20°C
[Ω]
Current
consumpt.
[A]
Power
consumpt
[W]
Coil code
K1 K7
SD12 12 4.5 2.67 32 1903780 1903760
SD24 24 18.6 1.29 31 1903781 1903761
Protection from atmospheric agents IEC 60529
The IP protection degree is guaranteed only with both valve and
connectors of an equivalent IP degree, correctly connected and
installed.
NOTE: In order to further reduce the emissions, with DC supply,
use of type H connectors is recommended. These prevent voltage
peaks on opening of the coil supply electrical circuit
(see cat. 49 000).
SUPPLY VOLTAGE FLUCTUATION
± 10% Vnom
MAX SWITCH ON FREQUENCY
18.000 ins/hr
DUTY CYCLE
100%
ELECTROMAGNETIC
COMPATIBILITY (EMC) (NOTE)
In compliance with
2014/30/EU
LOW VOLTAGE
In compliance with
2014/35/EU
CLASS OF PROTECTION
Coil insulation (VDE 0580)
Impregnation: DC valve
class H
class F
electric connection
electric
connection
protection
whole
valve
protection
K1 EN 175301-803 (ex DIN 43650) IP65
IP65
K7 DEUTSCH DT04 male IP65/67
41 155/119 ED
6/8
DS3B
SERIES 10
8 - OVERALL AND MOUNTING DIMENSIONS
dimensions in mm
solenoid position for SB* ,TB and TB* configurations
DS3B - S*
DS3B - RK
DS3B-SA*, DS3B-TA,
DS3B-TA*
1 Mounting surface with sealing rings:
4 OR 2037 (9.25x1.78) - 90 shore
2 Standard manual override included in the
solenoid tube
3 Coil (360° revolving)
4 Coil removal space
5 EN 175301-803 (ex DIN 43650) connector
To be ordered separately. See cat. 49 000
6 Connector removal space
7 Locking ring: tightening torque 5 ±0.5 Nm
Valve fastening: 4 SHC screws ISO 4762 M5x30
Tightening torque: 5 Nm (A8.8)
Threads of mounting holes: M5x10
41 155/119 ED
7/8
DS3B
SERIES 10
9 - INSTALLATION
Configurations with centering and return springs can be mounted in any position; type RK valves -
without springs and with mechanical detent - must be mounted with the longitudinal axis horizontal.
Valve fixing takes place by means of screws or tie rods, with the valve mounted on a lapped surface,
with values of planarity and smoothness that are equal to or better than those indicated in the drawing.
If the minimum values of planarity and/or smoothness are not met, fluid leakages between valve and
mounting surface can easily occur.
Surface finishing
11 - ELECTRIC CONNECTORS
Solenoid operated valves are delivered without connectors. Connectors type EN 175301-803 (ex DIN 43650) for K1 connections can be
ordered separately. See catalogue 49 000.
12 - MANUAL OVERRIDES
12.1 - CM-DS3/11 Manual override, boot protected
10 - ELECTRIC CONNECTIONS
connection for
DEUTSCH DT06-2S male connector
code K7
connection for EN 175301-803
(ex DIN 43650) connector
code K1 (standard)
Code: 3401150006
13 - PORT RESTRICTORS
Port restrictors are recommended if flow
variations which exceed the valve performance
limit during the switching processes occur, or for
circuit dampening.
Port restrictor plugs can be ordered separately
with the part numbers shown at left.
Ø (mm) part number
blank
0144162
0.6
0144163
0.8
0144033
1
0144034
Ø (mm) part number
1.2
0144035
1.5
0144036
1.8
0144164
2
0144165
41 155/119 ED
8/8
DS3B
SERIES 10
REPRODUCTION IS FORBIDDEN. THE COMPANY RESERVES THE RIGHT TO APPLY ANY MODIFICATIONS.
Supply voltage
D12 = 12 V
D24 = 24 V
Series no.:
14 - SPARE PARTS
SEALS KIT
The codes include the O-Ring n° 2, 5, and 6
Cod. 1985406 NBR seals
Cod. 1985410 FPM (viton) seals
COILS IDENTIFICATION CODE
1 Coil locking ring with seal included cod. 0119412
Tightening torque 5 ±0.5 Nm
2 ORM type 0220-20 (22x2) - 70 Shore
3 Coil (see identification code)
4 Solenoid tube for standard version:
TDS22-DS3/10N (NBR seals)
TDS22-DS3/10V (FPM seals)
NOTE: OR n°5 included
5 OR type 2062 (15.6x1.78) - 70 Shore
6 4 OR type 2037 (9.25x1.78) - 90 Shore
22S3
C - S / 12
NOTE: You can also order coils using the coil
codes at section 7.2
Coil electrical connection
K1 = plug for connector EN 175301-803
(ex DIN 43650)
K7 = plug DEUTSCH DT04-2P, for male
connector type DEUTSCH DT06-2S.
Type PMMD-AI3G with rear ports 3/8” BSP
Type PMMD-AL3G with side ports 3/8” BSP
15 - SUBPLATES
(see catalogue 51 000)
