21 111/314 ED
1/2
PRK10
PILOT OPERATED
PRESSURE CONTROL VALVE
SERIES 11
HYDRAULIC SYMBOL
OPERATING PRINCIPLESEAT DIMENSIONS: 7/8 - 14 UNF- 2B (SAE - 10)
— The PRK10 valve is a pilot operated pressure control valve,
cartridge type, that can be used in blocks or panels with
7/8-14 UNF-2B (SAE - 10) type seat.
— It is used to control the hydraulic circuit pressure and allows
use of the entire flow of the pump even at pressure values
near the set value.
— It consists of a main balanced type spool and a pilot stage.
The main spool, normally closed, opens when the circuit
pressure exceeds the set value generated by the pilot
stage, discharging the excess flow in port T, directly
connected to the tank.
— It’s available in 4 pressure control ranges from 6 to 350 bar.
— The PRK10 are supplied with a finishing surface treatment
(zinc-nickel) suitable to ensure a salt spray resistance up to
600 h (test according to UNI EN ISO 9227 standards and
test evaluation according to UNI EN ISO 10289 standards)
— The pressure is adjustable by a socket set screw with
locking nut, or by knob.
21 111/314 ED
CARTRIDGE TYPE
seat 7/8-14 UNF-2B (SAE - 10)
p max
350 bar
Q max 120 l/min
PERFORMANCES
(measured with mineral oil of viscosity 36 cSt at 50°C)
Max working pressure bar 350
Minimum controlled pressure and pressure drop see diagram
Maximum flow rate l/min 120
Ambient temperature range °C -20 / +60
Fluid temperature range °C -20 / +80
Fluid viscosity range cSt 10 ÷ 400
Fluid contamination degree
According to
ISO 4406:1999 class 20/18/15
Recommended viscosity cSt 25
Mass kg 0,2
Surface finishing: galvanic treatment zinc-nickel
21 111/314 ED
2/2
DUPLOMATIC OLEODINAMICA S.p.A.
20015 PARABIAGO (MI) Via M. Re Depaolini 24
Tel. +39 0331.895.111
Fax +39 0331.895.339
www.duplomatic.com e-mail: sales.exp@duplomatic.com
PRK10
SERIES 11
REPRODUCTION IS FORBIDDEN. THE COMPANY RESERVES THE RIGHT TO APPLY ANY MODIFICATIONS.
1 - IDENTIFICATION CODE
2 - CHARACTERISTIC CURVES
(values obtained with viscosity of 36 cSt at 50°C)
dimensions in mm
ADJUSTMENT
MINIMUM CONTROLLED PRESSURE
3 - HYDRAULIC FLUIDS
Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals (code N). For fluids HFDR type
(phosphate esters) use FPM seals (code V). For the use of other kinds of fluid such as HFA, HFB, HFC, please consult our technical
department. Using fluids at temperatures higher than 80 °C causes a faster degradation of the fluid and of the seals characteristics.
The fluid must be preserved in its physical and chemical characteristics.
4 - OVERALL AND MOUNTING DIMENSIONS
Series No. (the overall and mounting
dimensions remain unchanged from 10 to 19)
Pressure adjustment range:
070 = from 6 to 70 bar (17 bar / turn)
140 = from 6 to 140 bar (32 bar / turn)
210 = from 6 to 210 bar (47 bar / turn)
350 = from 6 to 350 bar (78 bar / turn)
Pressure control valve, pilot operated
Cartridge type
Size
R K 10 - / /11
P
1 OR type 2050 (12.42x1.78)
2 Parbak 8-014 (13.23x1.14x1.35)
3 OR type 3-910 (19.18x2.46)
4 Cartridge tightening: spanner 24
Tightening torque 38 Nm
5 Locking nut: spanner 13
6 Socket hex adjustment screw:
Hex key 4.
Rotate clockwise to increase
pressure
7 Locking ring
8 Adjustment knob: K
Seals:
N = NBR seals for mineral oils (standard)
V = FPM seals for special fluids
Option: K = Adjustment knob.
Omit for adjustment with hex socket
screw (standard)
