1/2
VCD1 0T.F3.01 - X - Y - Z
Insert type
Flow control, 2-way pressure
compensated, partially adjustable
These valves can be used either as lowering control devices or as
two ways flow regulators. In the firs option, they keep the lowering
speed largely independent from the load, while, in the second option,
they limit flow to the preset value which can be adjusted within the
regulate flow path. On the opposite flow direction, from 2 to 1, the
valve is acting as a free flow check reducing the pressure drop to low
values (see diagram ∆P – Q).
Technical data
Description
RE 18329-80/02.16
Replaces: RE 00162-02/01.11
Max. operating pressure bar (psi) 315 (4500)
Max. flow l/min. (gpm)
see “Flow range adjustment” table
and “Performance” graphs
Fluid temperature range °C (°F) -30 to 100 (-22 to 212)
Installation torque Nm (ft-lbs) see “Dimensions” table
Weight kg (lbs) see “Dimensions” table
Special cavity see “Dimensions”
Fluids
Mineral-based or synthetics with
lubricating properties at viscosities
of 10 to 500 mm
2
/s (cSt)
Filtration
Nominal value max. 10µm (NAS 8)
ISO 4406 19/17/14
Installation No restrictions
Other Technical Data See data sheet RE 18350-50
Note: available also as“Sleeve valve for line mounting”
See data sheets RE 18316-14, RE 18316-15,
RE 18316-16 and RE 18316-17
Free flow pressure drop
G 1/4
G 1/2
Performance curves: spring‘s length - flow (regulated flow) with nominal pressure of 50 bar (725 psi).
Curves rapresent the obtained flow range related to orifices 01-02-03-04-05.
G 3/8
G 3/4
2/2 Bosch Rexroth Oil Control S.p.A.
0TF301XYZ RE 18329-80/02.16
Dimensions
G *
A B C D E F Hex 1 Hex 2 H
Weight
kg (lbs)
Inst. torque
Nm (ft-lbs)
Flow max.
l/min. (gpm)
G 1/4
38.3
(1.51)
12.5
(0.49)
7
(0.28)
10
(0.39)
4
(0.16)
10.3
(0.41)
5.5
(0.22)
4.5
(0.18)
22
(0.87)
0.012
(0.027)
6 (4) 10 (3)
G 3/8
43
(1.69)
13.5
(0.53)
7
(0.28)
11.5
(0.45)
4
(0.16)
14
(0.55)
7
(0.28)
6
(0.24)
23
(0.91)
0.025
(0.055)
8 (6) 25 (7)
G 1/2
49
(1.93)
16
(0.63)
8
(0.32)
15
(0.59)
6
(0.24)
18.2
(0.72)
7
(0.28)
6
(0.24)
27
(1.06)
0.038
(0.084)
12 (9) 67 (18)
G 3/4
60
(2.36)
21
(0.83)
10
(0.39)
20
(0.79)
6
(0.24)
23
(0.91)
7
(0.28)
6
(0.24)
31
(1.22)
0.070
(0.154)
15 (11) 150 (40)
Performance
* Thread in accordance with ISO 228-1
RE 18329-80/02.16 0TF301XYZ
Bosch Rexroth Oil Control S.p.A.
3/4
Ordering code
Series 0/A to L
unchanged performances and dimensions
Insert type - Flow control
Flow range adjustment l/min. (gpm)
Adjustments
for Y = 09 for Y = 02 for Y = 03 for Y = 04
= 01
1-1.6
(0.26-0.42)
2.5-4
(0.66-1.06)
16-21
(4.23-5.55)
37-50
(9.78-13.2)
= 02
Locking nut + counter nut
see graphs ( ‘R‘ - Q )
-
= 02
1.6-2.5
(0.42-0.66)
4-6.3
(1.6-1.67)
21-28
(5.55-7.4)
50-67
(13.2-17.7)
= 03
2.5-4
(0.66-1.06)
6.3-10
(1.67-2.64)
28-37
(7.4-9.78)
67-90
(17.7-23.8)
Port sizes
= 09 G 1/4
= 04
4-6.3
(1.6-1.67)
10-16
(2.64-4.23)
37-50
(9.78-13.2)
90-120
(23.8-31.7)
= 02 G 3/8
= 05
6.3-10
(1.67-2.64)
16-25
(4.23-6.61)
50-67
(13.2-17.7)
120-150
(31.7-39.6)
= 03 G 1/2
= 04 G 3/4
0T.F3.01 X Y Z *
Type Material number
0TF301020201000 R931002328
0TF301020202000 R931002329
0TF301020203000 R931000012
0TF301020204000 R931000013
0TF301020205000 R931000424
0TF301020301000 R931002330
0TF301020302000 R931002332
0TF301020303000 R931002034
0TF301020304000 R931000342
0TF301020305000 R931002333
0TF301020401000 R931000014
0TF301020402000 R931002334
0TF301020403000 R931002335
0TF301020404000 R931002336
0TF301020405000 R931002337
0TF301020901000 R931000015
0TF301020902000 R931002324
0TF301020903000 R931002325
0TF301020904000 R931002326
0TF301020905000 R931002327
Type Material number
Special flow settings available.
Please contact factory authorized representative for ordering code
4/2 Bosch Rexroth Oil Control S.p.A.
0TF301XYZ RE 18329-80/02.16
© This document, as well as the data, specifications and other
information set forth in it, are the exclusive property of Bosch Rexroth
Oil Control S.p.a.. It may not be reproduced or given to third parties
without its consent.
The data specified above only serve to describe the product. No
statements concerning a certain condition or suitability for a certain
application can be derived from our information. The information given
does not release the user from the obligation of own judgment and
verification. It must be remembered that our products are subject to a
natural process of wear and aging.
Subject to change.
Bosch Rexroth Oil Control S.p.A.
Via Leonardo da Vinci 5
P.O. Box no. 5
41015 Nonantola – Modena, Italy
Tel. +39 059 887 611
Fax +39 059 547 848
cartridges@oilcontrol.com
www.boschrexroth.com
