RE 29361, edition: 2013-07, Bosch Rexroth AG
Proportional pressure relief valve,
pilot operated
Features
▶ Pilot operated valves for limiting a system pressure
▶ Operation by means of proportional solenoid
▶ For subplate mounting and threaded connection:
Porting pattern according to ISO 6264
▶ Maximum pressure limitation
▶ Valve and control electronics from a single source
▶ Integrated electronics (OBE) with type DBEME:
Little manufacturing tolerance of the command value
pressure characteristic curve
▶ External control electronics with type DBEM (sepa-
rateorder)
Contents
Features 1
Ordering code 2, 3
Symbols 3
Function, section 4, 5
Technical data 6, 7
Electrical connection 8, 9
Integrated electronics (OBE) 9
Characteristic curves 10 ... 12
Dimensions 13 ... 19
Accessories 19
▶ Size 10 to 32
▶ Component series 7X
▶ Maximum operating pressure 350 bar
▶ Maximum flow: 700 l/min
RE 29361 
Edition: 2013-07
Replaces: 2012-12
Type DBEM and DBEME
Similar figure
Inhalt
Features 1
Contents 1
Ordering code 2
Ordering code 3
Symbols 3
Function, section 4
Function, section 5
Technical data
(For applications outside these parameters, please consult
us!) 6
Technical data
(For applications outside these parameters, please consult
us!) 7
Electrical connection
(dimensions in mm) 8
Electrical connection 9
Integrated electronics (OBE) for type DBEME 9
Characteristic curves
(measured with HLP46, ϑ
oil
= 40 ±5 °C) 10
Characteristic curves
(measured with HLP46, ϑ
oil
= 40 ±5 °C) 11
Characteristic curves
(measured with HLP46, ϑ
oil
= 40 ±5 °C) 12
Dimensions: Type DBEM(E) 10
(dimensions in mm) 13
Dimensions: Type DBEM(E) 25
(dimensions in mm) 14
Dimensions: Type DBEM(E) 32
(dimensions in mm) 15
Dimensions: Type DBEM(E) 10G
(dimensions in mm) 16
Dimensions: Type DBEM(E) 25G
(dimensions in mm) 17
Dimensions: Type DBEM(E) 32G
(dimensions in mm) 18
Dimensions 19
Accessories
(not included in the delivery) 19
2/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Ordering code
01 Proportional pressure relief valve
DBE
02 With maximum pressure limitation M
1)
03 For external control electronics
no code
With integrated electronics (OBE)
E
Size
04 Size 10
10
Size 25
20
Size 32
30
05 Subplate mounting no code
Threaded connection G
06
Component series 70 to 79 (70 to 79: Unchanged installation and connection dimensions)
7X
Pressure rating
2)
07
Up to 50 bar
50
Up to 100 bar
100
Up to 200 bar
200
Up to 315 bar
315
Up to 350 bar
350
08
Pilot oil return external
Y
Unloading port X, pilot oil return external
XY
Supply voltage
09
24 V DC voltage
G24
10
1600 mA coil
no code
800 mA coil –8
3)
1)
The maximum pressure limitation only serves as protection against
overpressure in case of an error in the pilot valve (e.g. in case of
contamination or overcurrent).
2)
Special version DBEME-SO699 in size 10 and 20 available up to
pressure rating 500 bar.
3)
Replacement for series 3X and series 5X SO1 (comparison
seecharacteristic curve page 12). All characteristics (hydraulic
and electric) specified in the data sheet refer to the version
with1600mA coil.
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
DBE M ― 7X / G24 *
Proportional pressure relief valve, pilot operated | DBEM(E) 3/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Symbols
For external control electronics:
With integrated electronics:
Type DBEM...-7X/...Y...
Type DBEME...-7X/...Y...
Type DBEM...-7X/...XY...
Type DBEME...-7X/...XY...
Ordering code
Electrical connection
11
For type DBEM:
Without mating connector; connector DIN EN 175301-803 K4
4)
For type DBEME:
Without mating connector; connector DIN EN 175201-804 K31
4)
Electronics interface
12
Command value 0 to 10 V
A1
Command value 4 to 20 mA
F1
With DBEM
no code
Seal material
13
NBR seals
M
FKM seals
V
Attention: Observe compatibility of seals with hydraulic fluid used!
14 Pipe thread to DIN ISO228-1 no code
5)
UNF-thread to ASME B1.1 /12
5)
15
Further details in the plain text
4)
Mating connectors, separate order, see page 8 and 19
5)
possible only for version G
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
DBE M ― 7X / G24 *
4/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Valves of type DBEM are pilot operated pressure relief
valves. They are used to limit the operating pressure in
hydraulic systems. By means of these valves, the pressure
to be limited can be continuously adjusted depending on
the electric command value.
These valves basically consist of the housing (1) with main
spool insert (3), the sandwich plate valve with maximum
pressure limitation (2) and the proportional pilot control
valve (11).
Type DBEM...
The pressure applied to channel P acts on the main
spool(3). At the same time, the pressure at port P is
applied to the spring loaded side of the main spool (3) via
the control lines (6, 7) provided with nozzles (4, 5). Via the
connection bore (9), the pressure is simultaneously applied
to the poppet (10) of the proportional pilot control
valve(11). The hydraulic force at the pilot poppet (10) acts
against the command value-dependent force of the propor-
tional solenoid (12).
If the hydraulic force exceeds the solenoid force, the pilot
poppet is opened (10). The pilot oil can now flow via the
control line (13) into port Y (14) and to the tank; thus,
apressure drop results at the main spool (3) over the
control lines (6, 7). The connection from port P to T is
released. The main spool (3) controls the set operating
pressure at port P.
As hydraulic protection against inadmissibly high pressures,
a spring-loaded pressure relief valve (2) has been inte-
grated. This maximum pressure limitation is pre-set to the
relevant pressure rating (see table page 6). In the operating
range of the valve, the poppet (15) is held on the valve
seat(17) by the spring (16) and is thus closed. If the pres-
sure in the spring chamber of the main spool (3) exceeds
the maximum admissible set pressure of the valve, the
poppet (15) is pressed against the compression spring (16)
and the connection into the spring chamber is opened. Via
port Y (14), the pilot oil flows into the tank. Due to the
control lines (6, 7), a pressure drop occurs at the main
spool (3). The connection from port P to T is released. The
main spool (3) controls the set maximum operating pres-
sure in port P. Via the adjustment element (19), the pre-set
pressure can be reduced, if necessary. Port Y (14) must be
externally piped to the tank. The connection to the tank
should be pressureless. Via port X (18), the valve may be
unloaded or the maximum pressure may be limited.
Function, section
Type DBEM10-7X/..XYG24K4..











Proportional pressure relief valve, pilot operated | DBEM(E) 5/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Type DBEME – with integrated electronics (OBE)
In terms of function and design, these valves correspond to
type DBEM. On the proportional solenoid, there is more-
over a housing (19) with the control electronics.
Supply and command value voltage are applied to the
connector (20).
In the factory, the command value pressure characteristic
curve is adjusted with little manufacturing tolerance.
For more information on the control electronics,
seepage9.
Function, section


Type DBEME...-7X/...YG24K31
6/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Technical data
(For applications outside these parameters, please consult us!)
1)
Version G to 200 l/min
2)
The cleanliness classes specified for the components must be
adhered to in hydraulic systems. Effective filtration prevents faults
and at the same time increases the life cycle of the components.
For the selection of the filters see www.boschrexroth.com/filter.
hydraulic (measured with HLP46, ϑ
Oil
= 40 ±5 °C)
Size 10 Size 25 Size 32
Maximum operating pressure – Port P and X bar 350
– Port T bar 315
– Port Y bar Separately and to the tank at zero pressure
Maximum set pressure – Pressure rating 50 bar bar 50
– Pressure rating 100 bar bar 100
– Pressure rating 200 bar bar 200
– Pressure rating 315 bar bar 315
– Pressure rating 350 bar bar 350
Minimum set pressure with command value zero bar See characteristic curve page 10
Maximum pressure limitation, set upon delivery If necessary, the value may be reduced
– Pressure rating 50 bar bar to 75 bar
– Pressure rating 100 bar bar to 135 bar
– Pressure rating 200 bar bar to 240 bar
– Pressure rating 315 bar bar to 350 bar
– Pressure rating 350 bar bar to 390 bar
Maximum flow l/min
275
1)
550 700
Pilot flow l/min 0.4 to 1 0.4 to 1.5 0.4 to 1.5
Hydraulic fluid See table page 7
Hydraulic fluid temperature range °C –20 to +80
Viscosity range mm
2
/s 15 to 380
Maximum permitted degree of contamination of the hydraulic fluid -
cleanliness class according to ISO 4406 (c)
Class 20/18/15
2)
Hysteresis (see command value pressure characteristic curve) % ≤ 5 of the maximum set pressure
Linearity % ±3.5 of the maximum set pressure
Manufacturing tolerance of the com-
mand value pressure characteristic
curve, related to the hysteresis charac-
teristic curve; pressure increasing
– Type DBEM % ±5 of the maximum set pressure
– Type DBEME % ±1.5 of the maximum set pressure
Step response T
u
+ T
g
10 % → 90 % ms ~100 Measured with standing hydraulic fluid column,
0.2 liters at port A
90 % → 10 % ms ~100
Step response T
u
+ T
g
10 % → 90 % ms ~200 Measured with standing hydraulic fluid column,
5liters at port A
90 % → 10 % ms ~200
general Size 10 Size 25 Size 32
Weight – Type DBEM kg 4.5 5.3 6.4
– Type DBEME kg 4.7 5.5 6.6
– Type DBEMG
kg
7 6,74
6.4
– Type DBEMEG
kg
7,2 6,94
6.6
Installation position Any
Storage temperature range °C –20 to +80
Ambient temperature range – Type DBEM °C –20 to +70
– Type DBEME °C –20 to +50
Proportional pressure relief valve, pilot operated | DBEM(E) 7/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Technical data
(For applications outside these parameters, please consult us!)
electric G24 G24-8
Minimum solenoid current mA ≤ 100 ≤ 100
Maximum solenoid current mA 1600 ± 10 % 800 ± 5 %
Solenoid coil resistance – Cold value at 20 °C Ω 5.5 20.6
– Maximum hot value Ω 8.05 33
Duty cycle
% 100 100
Hydraulic fluid Classification Suitable sealing materials Standards
Mineral oils and related hydrocarbons HL, HLP NBR, FKM DIN 51524
Bio-degradable – Insoluble in water HETG NBR, FKM VDMA 24568
HEES FKM
– Soluble in water HEPG FKM VDMA 24568
Flame-resistant – Water-free HFDU, HFDR FKM ISO 12922
– Containing water HFC NBR ISO 12922
Important information on hydraulic fluids!
▶ For more information and data on the use of other hydraulic fluids
refer to data sheet 90220 or contact us!
▶ There may be limitations regarding the technical valve data (tem-
perature, pressure range, life cycle, maintenance intervals, etc.)!
▶ The flash point of the hydraulic fluid used must be 40 K higher
than the maximum solenoid surface temperature.
▶ Flame-resistant – containing water: Maximum pressure differen-
tial per control edge 210 bar, otherwise, increased cavitation
erosion. Life cycle as compared to HLP 30 to 100 %
Fluid temperature maximum 60 °C
▶ Bio-degradable: When using bio-degradable hydraulic fluids that
are simultaneously zinc-solving, zinc may accumulate in the fluid
(per pole tube 700 mg zinc).
electrical, integrated electronics (OBE)
Supply voltage – Nominal voltage VDC 24
– Lower limit VDC 21
– Upper limit VDC 35
Current consumption A ≤ 1.5
Required fuse protection A 2, time-lag
Inputs – Voltage V 0 to 10
– Current mA 4 to 20
Output – Actual current value mV 1 mV ≙ 1 mA
Protection class of the valve according to EN 60529 IP 65 with mating connector mounted and locked
Notice!
Information on the environment simulation testing for the areas EMC (electromagnetic compatibility), see declaration
on environmental compatibility data sheet 29162-U.
Caution!
At an ambient temperature of 70 °C and a duty cycle of 100 % with max. current, the coil reaches temperatures of
upto170 °C. Contact with the coil may lead to burns.
8/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Type DBEM
Type DBEME
Connection at the connector Connection at mating connector
Mating connector (black) accord-
ing to DIN EN 175301-803
Material no. R901017011
(separate order)
Sealing
material NBR
to the amplifier
Device connector allocation Contact Allocation interface "A1" Allocation interface "F1"
Supply voltage
A 24 VDC (u(t) = 21 V to 35 V); I
max
≤ 1.5 A
B 0 V
Reference potential actual value C Reference contact F; 0 V Reference contact F; 0 V
Differential amplifier input
D 0 to 10 V; R
E
= 100 kΩ 4 to 20 mA; R
E
= 100 Ω
E Reference potential command value
Measuring output (actual value) F 0 to 1.6 V actual value (1 mV ≙ 1 mA)
load resistance > 10
kΩ
Protective earth PE Connected to solenoid and valve housing
Plastic version,
material no. R900021267
(separate order)
Metal version,
material no. R900223890
(separate order)
Mating connectors according to DIN EN 175201-804, solder contacts for line cross-section 0.5 to 1.5 mm
2






Electrical connection
(dimensions in mm)



Chopper
amplifier
Current
controller
Characteristic curve
generator
Differential
amplifier
Solenoid
Oscillator
Command value
Reference potential
actual value
Reference potential
command value
Actual value
GND
24 VDC
Supply
Proportional pressure relief valve, pilot operated | DBEM(E) 9/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Block diagram
Length in mm →
Min. supply voltage in V→
Electrical connection
Connection cable for type DBEME
– Recommendation 6-wire, 0.75 or 1 mm
2
plus
protective earthing conductor and screening
– Only connect the screening to PE on the supply side
– Maximum admissible length 100 m
The minimum supply voltage at the power supply unit depends
on the length of the supply line (see diagram).
Integrated electronics (OBE) for type DBEME
Function
The electronics are supplied with voltage via ports A and B.
The command value is applied to the differential amplifier
ports D and E.
Via the characteristic curve generator, the command value
solenoid current characteristic curve is adjusted to the
valve so that non-linearities in the hydraulic system are
compensated for and a linear command value pressure
characteristic curve is created.
The current controller controls the solenoid current inde-
pendent of the solenoid coil resistance.
The power stage of the electronics for controlling the pro-
portional solenoid is a chopper amplifier with a cycle fre-
quency of approx. 180 Hz to 400 Hz. The output signal is
pulse-width modulated (PWM).
For checking the solenoid current, a voltage can be mea-
sured at the connector between pin F(+) and pin C(–) that
is proportional to the solenoid current. 1 mV corresponds
to 1 mA solenoid current
10/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
1)
Pressure in port P in % →
Command value in % →
Pressure in port P depending on the command value (flow = 24 l/min)
Characteristic curves
(measured with HLP46, ϑ
oil
= 40 ±5 °C)
Pressure in port P in % →
Command value in % →






 
   






Type DBEM Type DBEME
1)
With valve type DBEM, the manufacturing tolerance at the
external amplifier (type and data sheet see page 16) can
be changed using the command value attenuator potenti-
ometer "Gw". The digital amplifier is set using the param-
eter "Limit".
In this connection, the control current according to the
technical data must not be exceeded.
In order to be able to adjust several valves to the same
characteristic curve, don't set the pressure higher than the
maximum set pressure of the pressure rating with com-
mand value 100 %.
Set pressure depending on the flow
Min. set pressure in bar →
Flow in l/min →
  








  

   

 





Min. set pressure with command value 0
Min. set pressure in bar →
Flow in l/min →
The characteristic curves apply to output pressure in
Tor Y = 0 bar in the total flow range.
Notice: So that the minimum set pressure is achieved,
the pilot current must not exceed 100 mA.
Size 10
Size 32
Size 25
Size 10 Size 32Size 25
 







Min. set pressure in bar →
Flow in l/min →
Version G
(Characteristic curves for size 25
and size 30 identical to version
„subplate mounting“)
Size 10
Proportional pressure relief valve, pilot operated | DBEM(E) 11/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Pressure in bar →
Command value in % →
Command value pressure characteristic curves (measured with a flow of 24 l/min and with amplifier VT-MSPA1-1)
Characteristic curves
(measured with HLP46, ϑ
oil
= 40 ±5 °C)
Pressure in bar →
Command value in % →
Pressure rating 50 bar Pressure rating 100 bar
Pressure in bar →
Command value in % →
Pressure in bar →
Command value in % →
Pressure rating 200 bar
Pressure rating 315 bar
Pressure in bar →
Command value in % →
Pressure rating 350 bar











 










   











 






   







Pressure in bar →
Command value in % →
Pressure rating 100 bar (with amplifier VT-VSPA1-1)
 










12/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Characteristic curves
(measured with HLP46, ϑ
oil
= 40 ±5 °C)
Pressure in bar →
Command value in % →
Comparison series 5X and 7X using the pressure rating 315 bar as example
(with amplifier VT-SSPA1-1-1X with 800 mA coil)
= Series 7X








= Series 5X
Proportional pressure relief valve, pilot operated | DBEM(E) 13/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Valve mounting screws and subplates see page 19.
1
Seal rings for ports P and T
2
Seal ring for ports X
3
Space required to remove the mating connector
4
Name plate
5
Locating pin
6
Maximum pressure limitation
7
External pilot oil return,
separately and to the tank at zero pressure
8
Mating connector for type DBEM
9
Integrated electronics (OBE)
10
Mating connector for type DBEME
11
Cable fastening
Dimensions: Type DBEM(E) 10
(dimensions in mm)
O-ring and plastic nut for coil fixation. The nut can
be loosened by rotating it counterclockwise
(1turn). Afterwards, the solenoid coil can be
rotated in any desired position. Subsequent fixation
applying 5±1 Nm.
Coil and electronics
freely rotatable!
Notice!
The dimensions are nominal dimensions which are
subject to tolerances.


Required surface quality of the
valve contact surface
























14/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Valve mounting screws and subplates see page 19.
1
Seal rings for ports P and T
2
Seal ring for ports X
3
Space required to remove the mating connector
4
Name plate
5
Locating pin
6
Maximum pressure limitation
7
External pilot oil return,
separately and to the tank at zero pressure
8
Mating connector for type DBEM
9
Integrated electronics (OBE)
10
Mating connector for type DBEME
11
Cable fastening
Dimensions: Type DBEM(E) 25
(dimensions in mm)
O-ring and plastic nut for coil fixation. The nut can
be loosened by rotating it counterclockwise
(1turn). Afterwards, the solenoid coil can be
rotated in any desired position. Subsequent fixation
applying 5±1 Nm.
Coil and electronics
freely rotatable!
Notice!
The dimensions are nominal dimensions which are
subject to tolerances.


Required surface quality of the
valve contact surface
























Proportional pressure relief valve, pilot operated | DBEM(E) 15/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Valve mounting screws and subplates see page 19.


Required surface quality of the
valve contact surface
1
Seal rings for ports P and T
2
Seal ring for ports X
3
Space required to remove the mating connector
4
Name plate
5
Locating pin
6
Maximum pressure limitation
7
External pilot oil return,
separately and to the tank at zero pressure
8
Mating connector for type DBEM
9
Integrated electronics (OBE)
10
Mating connector for type DBEME
11
Cable fastening
Dimensions: Type DBEM(E) 32
(dimensions in mm)
O-ring and plastic nut for coil fixation. The nut can
be loosened by rotating it counterclockwise
(1turn). Afterwards, the solenoid coil can be
rotated in any desired position. Subsequent fixation
applying 5±1 Nm.
Coil and electronics
freely rotatable!
Notice!
The dimensions are nominal dimensions which are
subject to tolerances.
























16/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Dimensions: Type DBEM(E) 10G
(dimensions in mm)
P
T
58
Y
Y
G 1/4,
12 tief
15
56
1
2
4 5
3
192,5
155,6
101,5
6 7
1
8
15
max. 200
80
29
G1/2
Ø34
72
45,5
49,5
62
1
14
Ø11
1
14
12
G1/2
Ø34
47
58
77,2
5,5
179
45
X
G 1/4,
12 tief
O-ring and plastic nut for coil fixation. The nut can
be loosened by rotating it counterclockwise
(1turn). Afterwards, the solenoid coil can be
rotated in any desired position. Subsequent fixation
applying 5±1 Nm.
Coil and electronics
freely rotatable!
Valve mounting screws and subplates see page 19.
1 Space required to remove the mating connector
2 Name plate
3 Maximum pressure limitation
4 External pilot oil return,
separately and to the tank at zero pressure
5 Mating connector for type DBEM
6 Integrated electronics (OBE)
7 Mating connector for type DBEME
8 Cable fastening
Notice!
The dimensions are nominal dimensions which are
subject to tolerances.
Proportional pressure relief valve, pilot operated | DBEM(E) 17/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Dimensions: Type DBEM(E) 25G
(dimensions in mm)
O-ring and plastic nut for coil fixation. The nut can
be loosened by rotating it counterclockwise
(1turn). Afterwards, the solenoid coil can be
rotated in any desired position. Subsequent fixation
applying 5±1 Nm.
Coil and electronics
freely rotatable!
Valve mounting screws and subplates see page 19.
1 Space required to remove the mating connector
2 Name plate
3 Maximum pressure limitation
4 External pilot oil return,
separately and to the tank at zero pressure
5 Mating connector for type DBEM
6 Integrated electronics (OBE)
7 Mating connector for type DBEME
8 Cable fastening
Notice!
The dimensions are nominal dimensions which are
subject to tolerances.
P
T
58
Y
Y
G 1/4,
12 tief
15
56
1
2
4 5
3
192,5
155,6
101,5
6 7
1
8
15
max. 200
80
29
G1
Ø47
72
45,5
49,5
62
1
18
Ø11
1
18
12
G1
Ø47
47
58
77,2
5,5
179
45
X
G 1/4,
12 tief
18/20 DBEM(E) | Proportional pressure relief valve, pilot operated
Bosch Rexroth AG, RE 29361, edition: 2013-07
Dimensions: Type DBEM(E) 32G
(dimensions in mm)
O-ring and plastic nut for coil fixation. The nut can
be loosened by rotating it counterclockwise
(1turn). Afterwards, the solenoid coil can be
rotated in any desired position. Subsequent fixation
applying 5±1 Nm.
Coil and electronics
freely rotatable!
Valve mounting screws and subplates see page 19.
1 Space required to remove the mating connector
2 Name plate
3 Maximum pressure limitation
4 External pilot oil return,
separately and to the tank at zero pressure
5 Mating connector for type DBEM
6 Integrated electronics (OBE)
7 Mating connector for type DBEME
8 Cable fastening
Notice!
The dimensions are nominal dimensions which are
subject to tolerances.
P
T
58
Y
Y
G 1/4,
12 tief
15
56
1
2
4 5
3
192,5
155,6
101,5
6 7
1
8
15
max. 200
80
29
G1 1/2
Ø65
72
45,5
49,5
62
1
22
Ø11
1
22
12
G1 1/2
Ø65
47
58
77,2
5,5
179
45
X
G 1/4,
12 tief
Proportional pressure relief valve, pilot operated | DBEM(E) 19/20
RE 29361, edition: 2013-07, Bosch Rexroth AG
Dimensions
Accessories
(not included in the delivery)
Hexagon socket head cap screws (separate order)
Material number
Size 10 4x ISO 4762 - M12 x 50 - 10.9-flZn-240h-L
Friction coefficient µ
total
= 0.09 to 0.14;
Tightening torque M
A
= 75 Nm ±10 %
R913000283
Size 25 4x ISO 4762 - M16 x 50 - 10.9-flZn-240h-L
Friction coefficient µ
total
= 0.09 to 0.14;
Tightening torque M
A
= 185 Nm ±10 %
R913000378
Size 32
4x hexagon socket head cap screw
DIN 912 - M18 x 50 - 10.9-flZnnc-240h-L
Friction coefficient µ
total
= 0.09 to 0.14;
Tightening torque M
A
= 248 Nm ±10 %
R913031952
Notice: For reasons of stability, exclusively these valve mounting screws may be used. The tightening torque of the hexagon socket head cap
screws refers to the maximum operating pressure!
External control for type DBEM
(only standard version G24)
Data sheet Material number
VT-MSPA1-1-1X/V0/... in modular design (analog)
VT-VSPD-1-2X/V0/.-0-1 in Euro-card format (digital)
VT-VSPA1-2-1X/V0/...in Euro-card format (analog)
VT-SSPA1-1-1X/V0/0-24 as plug-in amplifier
30223
30523
30115
30116
Mating connectors (details see page 7)
Data sheet Material number
For type DBEM: Mating connectors according to DIN EN 175301-803
For type DBEME: Mating connectors according to DIN EN 175201-804
08006
08006
R901017011
R900021267 (plastic)
R900223890 (metal)
Subplates Data sheet Material number
Size 10, 25, 32 45064
Additionally
(800 mA version G24-8)
Data sheet Material number
VT-2000-5X/X/V0/... in Euro-card format
VT-MSPA1-30 in modular design (analog)
29904
30224
Bosch Rexroth AG
Hydraulics
Zum Eisengießer 1
97816 Lohr am Main, Germany
Phone +49 (0) 93 52 / 18-0
documentation@boschrexroth.de
www.boschrexroth.de
© This document, as well as the data, specifications and other information set
forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
duced or given to third parties without its consent.
The data specified above only serve to describe the product. No statements
concerning a certain condition or suitability for a certain application can be
derived from our information. The information given does not release the user
from the obligation of own judgment and verification. It must be remembered
that our products are subject to a natural process of wear and aging.
Bosch Rexroth AG, RE 29361, edition: 2013-07
20/20 DBEM(E) | Proportional pressure relief valve, pilot operated