G 1/4
G 3/8 G 1/2
1/2
SFC1 0T.F1.01.00 - Y - Z
Insert type
Flow control, 2-way pressure
compensated fixed setting
A constant flow rate, regardless of system pressures, is established
from 1 to 2 while a minimum pressure differential of 145 psi exists
between the two ports. The valve cannot be adjusted for variable flow
output. Flow from 2 to 1 is limited by the diameter of the selected
control orifice and is not pressure compensated.
Technical data
Description
Performance
RE 18329-75/03.16
Replaces: RE 18329-75/02.16
Max. operating pressure bar (psi) 210 (3000)
Max. flow l/min. (gpm)
see “Regulated flow range” table
Fluid temperature range °C (°F) -30 to 100 (-22 to 212)
Weight kg (lbs) see “Dimensions” table
Special cavity see “Dimensions”
Lines bodies and standard
assemblies
Please refer to section “Hydraulic
integrated circuit” or consult
factory
Fluids
Mineral-based or synthetics
with lubricating properties at
viscosities of 10 to 500 mm
2
/s (cSt)
Recommended degree of fluid
contamination
Nominal value max. 10µm (NAS 8)
ISO 4406 19/17/14
Installation No restrictions
Other Technical Data See data sheet RE 18350-50
2/2 Bosch Rexroth Oil Control S.p.A.
0TF10100YZ RE 18329-75/03.16
© This document, as well as the data, specifications and other
information set forth in it, are the exclusive property of Bosch Rexroth
Oil Control S.p.a.. It may not be reproduced or given to third parties
without its consent.
The data specified above only serve to describe the product. No
statements concerning a certain condition or suitability for a certain
application can be derived from our information. The information given
does not release the user from the obligation of own judgment and
verification. It must be remembered that our products are subject to a
natural process of wear and aging.
Subject to change.
Bosch Rexroth Oil Control S.p.A.
Via Leonardo da Vinci 5
P.O. Box no. 5
41015 Nonantola – Modena, Italy
Tel. +39 059 887 611
Fax +39 059 547 848
compact-hydraulics-cv@boschrexroth.com
www.boschrexroth.com/compacthydraulics
Dimensions
Ordering code
Series 0/A to L
unchanged performances and dimensions
Insert type - Flow control,
2-way pressure compensated
fixed setting
Regulated flow range l/min. (gpm)
= 01 = 02 = 03 = 04 = 05 = 06 = 07 = 08 = 09 = 10
for
Y=09
1 (0.3)
± 20%
2 (0.5)
± 20%
3 (0.8)
± 20%
4 (1.1)
± 15%
5 (1.3)
± 15%
6 (1.6)
± 15%
7 (1.9)
± 15%
8 (2.1)
± 15%
9 (2.4)
± 15%
10 (2.6)
± 15%
Port sizes
= 09 G 1/4
for
Y=02
4 (1.1)
± 15%
5 (1.3)
± 15%
6 (1.6)
± 15%
8 (2.1)
± 15%
10 (2.6)
± 15%
12 (3.2)
± 15%
14 (3.7)
± 10%
16 (4.2)
± 10%
- -
= 02 G 3/8
= 03 G 1/2
for
Y=03
12 (3.2)
± 15%
16 (4.2)
± 10%
20 (5.3)
± 10%
25 (6.6)
± 10%
30 (7.9)
± 10%
35 (9.3)
± 10%
40 (10.6)
± 10%
- - -
G *
A B C D E F I H H1
Weight
kg (lbs)
Flow max.
l/min. (gpm)
G 1/4 25.5 (1) 13.5 (0.53) 8.5 (0.34) 3 (0.12) 8 (0.32) 10 (0.39) 11 (0.43) 5 (0.2) 1.5 (0.6) 0.011 (0.024) 10 (3)
G 3/8 28 (1.1) 15 (0.59) 10.5 (0.41) 2 (0.08) 11 (0.43) 14 (0.55) 14.5 (0.57) 5 (0.2) 1.5 (0.6) 0.024 (0.053) 16 (4)
G 1/2 35 (1.38) 19.5 (0.77) 13 (0.52) 2 (0.08) 14 (0.55) 17.5 (0.69) 17.5 (0.69) 5 (0.2) 1.5 (0.6) 0.048 (0.106) 40 (11)
0T.F1.01.00 Y Z *
Type Material number
0TF101000201000 R931002311
0TF101000202000 R931002312
0TF101000203000 R931002313
0TF101000204000 R931002314
0TF101000205000 R931000009
0TF101000206000 R931002315
0TF101000207000 R931002316
0TF101000208000 R931002317
0TF101000301000 R931002318
0TF101000302000 R931002319
0TF101000303000 R931002320
0TF101000304000 R931002321
0TF101000305000 R931002322
Type Material number
0TF101000306000 R931002063
0TF101000307000 R931001404
0TF101000901000 R931002304
0TF101000902000 R931000010
0TF101000903000 R931000272
0TF101000904000 R931002305
0TF101000905000 R931002306
0TF101000906000 R931000011
0TF101000907000 R931002307
0TF101000908000 R931002308
0TF101000909000 R931002309
0TF101000910000 R931002310
Note: available also as“Sleeve valve for line
mounting”
See data sheets RE 18316-12 and RE 18316-13
* Thread in accordance with ISO 228-1
