RE 18320-95/02.2016, Bosch Rexroth Oil Control S.p.A.
Technical data
Max. operating pressure 380 bar (5510 psi)
Max. flow 40 l/min. (11 gpm)
Max. internal leakage
1)
70 cm
3
/min. (4 cu.in./min.)
Fluid temperature range -30 to 100 °C (-22 to 212 °F)
Installation torque 41 - 47 Nm (30 - 35 ft-lbs)
Weight 0.21 kg (0.46 lbs)
Special cavity 1004
Lines bodies and standard
assemblies
Please refer to section “Hydraulic
integrated circuit” or consult factory
Seal kit
2)
Code: RG1004010520100
material no: R930058605
Fluids Mineral-based or synthetics with
lubricating properties at viscosities of
5 to 800 mm
2
/s (cSt)
Recommended degree of
fluid contamination
Nominal value max. 10µm (NAS 8) /
ISO 4406 19/17/14
Installation position No restrictions
Other Technical Data See data sheet 18350-50
1) Measured at 200 bar (2900 psi)
2) Only external seals for 10 valves
Description
Directional hot oil shuttle valves permit hot oil to be diverted
from the low pressure side of a closed loop system. When
ports 2 and 3 are at same pressure values, valve configuration
is with all ports 2, 3 and 4 closed and the valve spool is
centered by the spring. If pressure at port 2 (or port 4) is
higher than port 4 (or 2), then port 4 (or 2) is connected to
port 3. Port 1 is not used.
Application notes: directional hot oil shuttle valves are
especially designed as flushing valves to remove heat from
closed loop hydraulic circuits; generally hydraulic fluid is
directed from the low pressure side into the motor housing
then it is fed into the reservoir. The hydraulic fluid, removed
out of the closed circuit must be replaced by cooled hydraulic
fluid from the pump.
Directional hot oil, shuttle
Special cavity, 1004
RE 18320-95
Edition: 02.2016
SELO-10M 04.94.10 - X - 99 - Z
Characteristic curve
Flow Q
Pressure Δp
2
Bosch Rexroth Oil Control S.p.A., RE 18320-95/02.2016
Bosch Rexroth Oil Control S.p.A.
Via Leonardo da Vinci 5
P.O. Box no. 5
41015 Nonantola – Modena, Italy
Tel. +39 059 887 611
Fax +39 059 547 848
compact-hydraulics-cv@boschrexroth.com
www.boschrexroth.com/compacthydraulics
© This document, as well as the data, specifications and other information set
forth in it, are the exclusive property of Bosch Rexroth Oil Control S.p.a.. It
may not be reproduced or given to third parties without its consent. The data
specified above only serve to describe the product. No statements concerning
a certain condition or suitability for a certain application can be derived from
our information. The information given does not release the user from the
obligation of own judgment and verification. It must be remembered that our
products are subject to a natural process of wear and aging. Subject to change.
SELO-10M | Directional hot oil, shuttle
Dimensions [mm (inches)]
Type Material number
049410009918000 R930058604
Type Material number
Dimensions
Ordering code
04.94.10 X 99 Z 00 *
Series 0/A to L
unchanged performances and dimensions
Directional hot oil, shuttle
Version and options standard
SPRINGS
Adjustments
Std. setting
bar (psi)
00 Fixed setting
18 18 (261)
99 Special cavity, 1004
Preferred types
