RE 91520/11.2015, Bosch Rexroth AG
Features
▶ Flange and shaft designed for direct mounting on the
power take-off of commercial vehicles
▶ Weight-optimized thanks to diecast aluminum housing.
▶ No case drain line necessary
▶ Reduced noise
▶ Straightforward adjustment of direction of drive
▶ Excellent suction performance
▶ High total efficiency
▶ Long service life
▶ High-pressure pump for use in commercial vehicles
▶ Sizes 23 to 107
▶ Nominal pressure/maximum pressure 350/400bar
▶ Bent-axis design
▶ Open circuit
Axial piston fixed pump
A17FO Series 10
RE 91520
Issue: 11.2015
Replaces: 10.2014
Contents
Ordering code 2
Hydraulic fluid 3
Operating pressure range 4
Technical Data 5
Direction of rotation 7
Dimensions, sizes 23, 32 8
Dimensions, size 45 9
Dimensions, size 63 10
Dimensions, size 80 11
Dimensions, size 107 12
Accessories 13
Installation instructions 15
Other related documents 15
Project planning notes 16
Safety instructions 16
2
Bosch Rexroth AG, RE 91520/11.2015
A17FO Series 10 | Axial piston fixed pump
Ordering code
Ordering code
01 02 03 04 05 06 07 08 09 10 11
A17F O / 10 N L W K0 E8 1 –
Axial piston unit
01 Bent-axis design, fixed, nominal pressure 350 bar, maximum pressure 400 bar, for commercial vehicles (truck)
A17F
Operating mode
02 Pump, open circuit
O
Sizes (NG)
03 Geometric displacement, see table of values on page 5
023 032 045 063 080 107
Series
04 Series 1, index 0
10
Configuration of port and fastening threads
05 Metric, port threads with profiled sealing ring according to DIN3852
N
Direction of rotation
1)
06 Viewed on drive shaft counter-clockwise
L
Sealing material
07 FKM (fluor-caoutchouc) including the 2 shaft seal rings in FKM
W
Mounting flange
08 Special flange ISO 7653-1985 (for trucks)
K0
Drive shaft
09 Splined shaft similar to DIN ISO 14 (for trucks)
E8
Service line port
10 Threaded ports A and S at rear
1
Standard / special version
11 Standard version
0
Special version
S
Note
Note the project planning notes on page16.
1) Changing the direction of rotation see instruction manual 91520-01-B,
chapter 6.4.2
3
RE 91520/11.2015, Bosch Rexroth AG
Axial piston fixed pump | A17FO Series 10
Hydraulic fluid
Hydraulic fluid
The fixed pump A17FO is designed for operation with HLP
mineral oil according to DIN 51524.
Application instructions and requirements for hydraulic
fluids should be taken from the following data sheets
before the start of project planning:
▶ 90220: Hydraulic fluids based on mineral oils and
related hydrocarbons
▶ 90221: Environmentally acceptable hydraulic fluids
▶ 90222: Fire-resistant, water-free hydraulic fluids
(HFDR/HFDU)
The axial piston unit is not suitable for operation with
water-containing HF hydraulic fluid.
Notes on selection of hydraulic fluid
The hydraulic fluid should be selected such that the operat-
ing viscosity in the operating temperature range is within
the optimum range (ν
opt
see selection diagram).
Note
At no point of the component may the temperature be
higher than 115°C. The temperature difference specified in
the table is to be taken into account when determining the
viscosity in the bearing.
Please contact us if the above conditions cannot be met
due to extreme operating parameters.
Viscosity and temperature of hydraulic fluids
Viscosity Temperature Comment
Cold start
ν
max
≤1600mm
2
/s θ
St
≥ –25 °C
1)
t≤3min, without load (p≤50bar), n≤1000rpm
Permissible temperature difference
ΔT≤25K
between axial piston unit and hydraulic fluid in the system
Warm-up phase
ν<1600 to 400 mm
2
/s at p≤0.7×p
nom
, n≤0.5×n
nom
and t≤15min
Continuous operation
ν=400 to 10 mm
2
/s
this corresponds, for VG46 for example, to a temperature range
of +5°C to +85°C (see selection diagram)
θ=-25°C to +103°C
measured at air bleed port R
observe permissible temperature range of the shaft seal ring
1)
(ΔT=approx.12K between bearing/shaft seal and port R)
ν
opt
=36 to 16mm
2
/s
range of optimum operating viscosity and efficiency
Short-term operation
ν
min
≥7mm
2
/s t<3min, p<0.3×p
nom
▼ Selection diagram
−40 −25 −10 10 30 50 90 11570
0
7
10
40
60
20
100
200
400
600
1000
1600
VG 22
VG 32
VG 46
VG 68
VG 100
16
36
Optimum operating viscosity range v
opt
Optimum efficiency
Maximum permissible viscosity for cold start
Minimum permissible viscosity for short-term operation
Temperature θ [°C]
Viscosity ν [mm
2
/s]
Continuous operation
Warm-up phase
Minimum permissible temperature for cold start
1) The FKM shaft seal is permissible for temperatures of –25°C to
+115°C, please contact us for temperatures below –25°C.
4
Bosch Rexroth AG, RE 91520/11.2015
A17FO Series 10 | Axial piston fixed pump
Operating pressure range
Filtration of the hydraulic fluid
Finer filtration improves the cleanliness level of the hydraulic
fluid, which increases the service life of the axial piston unit.
A cleanliness level of at least 20/18/15 is to be maintained
according to ISO4406.
At very high hydraulic fluid temperatures (90°C to maximum
103°C, measured at air bleed port R), a cleanliness level of at
least 19/17/14 according to ISO4406 is necessary.
Operating pressure range
Pressure at service line port A (high-pressure side) Definition
Nominal pressure p
nom
350 bar absolute The nominal pressure corresponds to the maximum design pres-
sure.
Maximum pressure p
max
400 bar absolute The maximum pressure corresponds to the maximum operating
pressure within the single operating period. The sum of the single
operating periods must not exceed the total operating period.
Single operating period 5s
Total operating period 50 h
Minimum pressure (high-pressure side) 10 bar absolute Minimum pressure at the high-pressure side (A) which is required
in order to prevent damage to the axial piston unit.
Rate of pressure change R
Amax
9000bar/s Maximum permissible rate of pressure rise and reduction during
apressure change over the entire pressure range.
Pressure at suction port S (inlet)
Minimum pressure p
Smin
0.8 bar absolute
Minimum pressure at suction port S (inlet) which is required in order
to prevent damage to the axial piston unit. The minimum pressure is
dependent on the speed of the axial piston unit.
Maximum pressure p
Smax
2bar absolute
▼ Rate of pressure change R
Amax
p
nom
∆t
∆p
Time t
Pressure p
▼ Pressure definition
Pressure p
t
1
t
2
t
n
Single operating period
Minimum pressure (high-pressure side)
Maximum pressure p
max
Nominal pressure p
nom
Time t
Total operating period = t
1
+ t
2
+ ... + t
n
Note
Operating pressure range valid when using hydraulic
fluids based on mineral oils. Values for other hydraulic
fluids, please contact us.
5
RE 91520/11.2015, Bosch Rexroth AG
Axial piston fixed pump | A17FO Series 10
Technical Data
Technical Data
Size NG 23 32 45 63 80 107
Displacement, geometric, per revolution
V
g
cm
3
22.9 32 45.6 63 80.4 106.7
Speed maximum
1)
n
nom
2)
rpm 3050 2750 2650 2200 2150 2000
n
max
3)
rpm 4300 3900 3800 3200 3100 2800
Flow
at n
nom
q
v
l/min 70 88 121 139 173 213
Power
at n
nom
and Δp = 350 bar P
kW 41 51 71 81 101 124
Torque
at Δp = 350 bar T
Nm 127 178 254 351 448 594
Rotary stiffness
c
kNm/rad 2.56 3.12 4.18 6.25 8.73 11.2
Moment of inertia for rotary group
J
TW
kgm
2
0.0012 0.0012 0.003 0.0042 0.0072 0.0116
Maximum angular acceleration
α
rad/s² 6500 6500 14600 7500 6000 4500
Case volume
V
l 0.25 0.29 0.4 0.5 0.6 0.75
Mass moment
T
G
Nm 4.7 4.7 8.6 9.9 15.3 20
Mass (approx.)
m
kg 5.9 5.9 8.4 9.3 12.3 15.0
▼ Maximum speed (limiting speed)
0.8
1
1.5
2
0.8
1.1
0.9
1.2
1.3
1.0
1.4
1.5
Inlet pressure p
S abs
[bar]
Speed n/n
nom
Determining the operating characteristics
Flow
q
v
=
V
g
×n×η
v
[l/min]
1000
Torque
T
=
V
g
×Δp
[Nm]
20×π×η
hm
Power
P
=
2π×T×n
=
q
v
× Δp
[kW]
60000
600 × η
t
Key
V
g
Displacement per revolution [cm
3
]
Δp
Differential pressure [bar]
n
Speed [rpm]
η
v
Volumetric efficiency
η
hm
Hydraulic-mechanical efficiency
η
t
Total efficiency (η
t
= η
v
× η
hm
)
Note
▶ Theoretical values, without efficiency and tolerances;
values rounded.
▶ Operation above the maximum values or below the
minimum values may result in a loss of function,
areduced service life or in the destruction of the axial
piston unit. Other permissible limit values, such as
speed variation, reduced angular acceleration as a
function of the frequency and the permissible angular
acceleration at start (lower than the maximum angular
acceleration) can be found in data sheet 90261.
1) The values are applicable:
– for the optimum viscosity range from ν
opt
= 36 bis 16 mm
2
/s
– for hydraulic fluids based on mineral oils.
2) The values apply at absolute pressure p
abs
= 1 bar at suction port S
3) Maximum speed (speed limit) with increased inlet pressure p
abs
at
suction port S
(see diagram)
.
6
Bosch Rexroth AG, RE 91520/11.2015
A17FO Series 10 | Axial piston fixed pump
Operating pressure range
Permissible axial forces of the drive shaft
Size NG 23 32 45 63 80 107
Maximum axial force, at standstill or
pressure-free operation
F
ax
+
–
+ F
ax max
N 0 0 0 0 0 0
− F
ax max
N 24 33 43 53 60 71
Note
▶ The values given are maximum values and do not apply
to continuous operation.
▶ The permissible axial force in direction −F
ax
is to be
avoided as the lifetime of the bearing is reduced.
▶ Radial forces are not permissible.
7
RE 91520/11.2015, Bosch Rexroth AG
Axial piston fixed pump | A17FO Series 10
Direction of rotation
Direction of rotation
The direction of rotation of the axial piston unit is defined
by means of a pressure connection screwed into the ser-
vice line port and can easily be changed.
By changing the pressure connection, the service line port
and the suction port are exchanged. As a result, the permis-
sible drive direction is changed. This is necessary when
mounting on a power take-off with counter-clockwise rota-
tion, for example. The procedure for conversion of the
pressure nipple can be found in the instruction manual
(91520-01-B, chapter 6.4.2 “Direction of rotation and
change of direction of rotation”).
Direction of rotation on delivery
On delivery, the pressure connection (1) is pre-assembled
in the right-hand service line port of the axial piston unit.
The permissible drive direction of the pump looking at the
drive shaft: counter-clockwise. The power take-off turns
clockwise.
Note
The pressure connection is pre-installed upon delivery and
must be tightened with the torque stipulated for the appro-
priate thread size prior to installation (see instruction
manual).
1
2
12
X
1
2
Druckstutzen
(im rechten Anschluss)
Sauganschluss S
Ansicht X
Drehrichtung
der Pumpe
8
Bosch Rexroth AG, RE 91520/11.2015
A17FO Series 10 | Axial piston fixed pump
Dimensions, sizes 23, 32
Dimensions [mm]
Dimensions, sizes 23, 32
R
X
A
S
ø80
-0.06
-0.03
185
173
159
15
107
96
80
9
43
51.8
88
91
58
76
88
103
40°
13
80
105
G1/2
G3/4
88
81
25.8
0.7
Ports Standard Size
p
max abs
[bar]
2)
State
5)
A Service line port DIN ISO 228 G1/2; 14 deep 400 O
S Suction port DIN ISO 228 G3/4; 16 deep 2 O
R Air bleed port DIN 3852
4)
M10 x 1, 8 deep 2 X
3)
Center of gravity
Drive shaft
Splined shaft similar to DIN ISO 14
E8 ‒ 8x32x35
Groove for retaining ring 35 × 1.5 DIN 471
9.5
55
28
12
36.8
26.1
M12 x 1.75
1)
ø34.9
-0.1
ø8.1
ø42
ø38.4
Detail X
1) Center bore according to DIN 332 (thread according to DIN 13)
2) Momentary pressure spikes may occur depending on the application.
Keep this in mind when selecting measuring devices and fittings.
3) Only open port R for filling and air bleeding.
4) The spot face can be deeper than as specified in the appropriate
standard.
5) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
9
RE 91520/11.2015, Bosch Rexroth AG
Axial piston fixed pump | A17FO Series 10
Dimensions, size 45
Dimensions [mm]
Dimensions, size 45
108
58.8
G3/4
108
G1
105
80
13
108
107
103
96
80
R132
223
210
194
15
9
43
63
89
102
119
40°
ø80
-0.06
-0.03
S
A
R
X
104
29
0.8
Ports Standard Size
p
max abs
[bar]
2)
State
5)
A Service line port DIN ISO 228 G3/4; 16 deep 400 O
S Suction port DIN ISO 228 G1; 18 deep 2 O
R Air bleed port DIN 3852
4)
M10 x 1, 8 deep 2 X
3)
Drive shaft
Splined shaft similar to DIN ISO 14
E8 ‒ 8x32x35
Groove for retaining ring 35 × 1.5 DIN 471
9.5
55
28
12
36.8
26.1
M12 x 1.75
1)
ø34.9
-0.1
ø8.1
ø42
ø38.4
1) Center bore according to DIN 332 (thread according to DIN 13)
2) Momentary pressure spikes may occur depending on the application.
Keep this in mind when selecting measuring devices and fittings.
3) Only open port R for filling and air bleeding.
4) The spot face can be deeper than as specified in the appropriate
standard.
5) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
Center of gravity
Detail X
10
Bosch Rexroth AG, RE 91520/11.2015
A17FO Series 10 | Axial piston fixed pump
Dimensions, size 63
Dimensions [mm]
Dimensions, size 63
Ports Standard Size
p
max abs
[bar]
2)
State
5)
A Service line port DIN ISO 228 G3/4; 16 deep 400 O
S Suction port DIN ISO 228 G1; 18 deep 2 O
R Air bleed port DIN 3852
4)
M10 x 1, 8 deep 2 X
3)
1) Center bore according to DIN 332 (thread according to DIN 13)
2) Momentary pressure spikes may occur depending on the application.
Keep this in mind when selecting measuring devices and fittings.
3) Only open port R for filling and air bleeding.
4) The spot face can be deeper than as specified in the appropriate
standard.
5) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
232
219
203
15
9
43
107
96
80
103
108
64
G3/4
G1
108
126
110
96
ø80
-0.06
63
40°
-0.03
108
80
105
13
S
A
R
X
R132
109
32
0.8
Drive shaft
Splined shaft similar to DIN ISO 14
E8 ‒ 8x32x35
9.5
55
28
12
36.8
26.1
M12 x 1.75
1)
ø34.9
-0.1
ø8.1
ø42
ø38.4
Groove for retaining ring 35 × 1.5 DIN 471
Center of gravity
Detail X
11
RE 91520/11.2015, Bosch Rexroth AG
Axial piston fixed pump | A17FO Series 10
Dimensions, size 80
Dimensions [mm]
Dimensions, size 80
261
245
227
15
R
9
43
114
107
96
X
80
69
117
124
G1
G1 1/4
117
S
A
121
80
105
13
140
120
105
67.5
40°
ø80
-0.06
-0.03
R118
127
36
1.0
Ports Standard Size
p
max abs
[bar]
2)
State
5)
A Service line port DIN ISO 228 G1; 18 deep 400 O
S Suction port DIN ISO 228 G1 1/4; 20 deep 2 O
R Air bleed port DIN 3852
4)
M10 x 1, 8 deep 2 X
3)
Drive shaft
Splined shaft similar to DIN ISO 14
E8 ‒ 8x32x35
9.5
55
28
12
36.8
26.1
M12 x 1.75
1)
ø34.9
-0.1
ø8.1
ø42
ø38.4
Groove for retaining ring 35 × 1.5 DIN 471
1) Center bore according to DIN 332 (thread according to DIN 13)
2) Momentary pressure spikes may occur depending on the application.
Keep this in mind when selecting measuring devices and fittings.
3) Only open port R for filling and air bleeding.
4) The spot face can be deeper than as specified in the appropriate
standard.
5) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
Center of gravity
Detail X
12
Bosch Rexroth AG, RE 91520/11.2015
A17FO Series 10 | Axial piston fixed pump
Dimensions, size 107
Dimensions [mm]
Dimensions, size 107
ø80
-0.06
-0.03
77
129
G1
G1 1/4
129
S
A
120
107
96
80
133
13
80
X
R
105
272
256
238
15
9
43
149
129
114
73.5
40°
136
41
1.0
Ports Standard Size
p
max abs
[bar]
2)
State
5)
A Service line port DIN ISO 228 G1; 18 deep 400 O
S Suction port DIN ISO 228 G1 1/4; 20 deep 2 O
R Air bleed port DIN 3852
4)
M10 x 1, 8 deep 2 X
3)
Drive shaft
Splined shaft similar to DIN ISO 14
E8 ‒ 8x32x35
9.5
55
28
12
36.8
26.1
M12 x 1.75
1)
ø34.9
-0.1
ø8.1
ø42
ø38.4
Groove for retaining ring 35 × 1.5 DIN 471
1) Center bore according to DIN 332 (thread according to DIN 13)
2) Momentary pressure spikes may occur depending on the application.
Keep this in mind when selecting measuring devices and fittings.
3) Only open port R for filling and air bleeding.
4) The spot face can be deeper than as specified in the appropriate
standard.
5) O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
Center of gravity
Detail X
13
RE 91520/11.2015, Bosch Rexroth AG
Axial piston fixed pump | A17FO Series 10
Accessories
Dimensions [mm]
Accessories
Suction stud
▼ Dimensions
K4
K5
SW
K2
K0
K3
K1
SW
K3
K1
K2
K0
K4
K5
K6
K3
K1
K2
K0
K4
K5
K6
SW
K7
K9
K8
K7
K9
K8
K7
K9
K8
Version Pump size Hose
nominal
width
Material
number
Thread
K0
K1 K2 K3 K4 K5 K6 K7 K8 K9 SW
Straight
23, 32 1 1/2" R909831856 G3/4 39 18 33.5 70 54 ‒ 221 132 186 41
45 1 1/2"
R902600251
G1 39 23.5 33.5 72 54 ‒ 248 139 197 41
63 1 1/2" G1 39 23.5 33.5 72 54 ‒ 257 146 204 41
63 2" R902602028 G1 51 26 44 82 64 ‒ 268 157 215 55
80 2"
R902600252
G1 1/4 51 30 44 85 65 ‒ 295 168 232 55
107 2" G1 1/4 51 30 44 85 65 ‒ 306 177 245 55
107 2 1/2" R902601630 G1 1/4 63 31 54 82 64 ‒ 308 180 248 65
45°
23, 32 1 1/2" R909831601 G3/4 39 20 31 101 82 43 259 126 180 36
45 1 1/2"
R909831600
G1 39 26 31 101 82 45 287 132 190 41
63 1 1/2" G1 39 26 31 101 82 45 296 139 197 41
63 2" R902602029 G1 51 26 43 100 81 44 295 145 203 41
80 2"
R909831597
G1 1/4 51 34 43 101 81 40 317 156 220 50
107 2" G1 1/4 51 34 43 101 81 40 328 165 234 50
107 2 1/2" R902601631 G1 1/4 63 35 54 100 81 44 331 169 237 50
90°
23, 32 1 1/2" R909831602 G3/4 39 20 31 62 43 81 265 117 171 36
45 1 1/2"
R909831599
G1 39 26 31 64 44 85 296 127 185 41
63 1 1/2" G1 39 26 31 64 44 85 305 134 192 41
63 2" R902602030 G1 51 26 43 62 42 81 305 138 196 41
80 2"
R909831598
G1 1/4 51 35 43 63 43 80 330 144 208 50
107 2" G1 1/4 51 35 43 63 43 80 341 153 221 50
The suction stud is not included in the scope of delivery
and must be ordered separately.
14
Bosch Rexroth AG, RE 91520/11.2015
A17FO Series 10 | Axial piston fixed pump
Dimensions, size 107
Dimensions [mm]
Notes on suction line
▶ Keep as short and straight as possible, without sharp bend
▶ Use a supporting ring for plastic hoses
▶ Use two hose clamps to protect the suction hose against
air suction
▶ Note pressure resistance of suction hose compared to
ambient pressure
Replacing seals
The O-rings used as seals to prevent air from entering the
suction line are to be replaced after every removal and new
installation in order to guarantee complete sealing.
Material number for O-rings:
▶ R909083796: O-ring for suction stud G3/4
▶ R909083802: O-ring for suction stud G1
▶ R909083808: O-ring for suction stud G1 1/4
Coupling flange
There are special, modified coupling flanges in 4-hole and
6-hole design for the cardan shaft drive.
The coupling flange is not included in the scope of delivery
and must be ordered separately.
▼ 4-hole coupling flange, complete – ø 90
Material number: R902060152
ø90
ø47
-0.025
2.3 6
48.2
42.5
ø8.5
ø74.5
M12 × 35 - 10.9
0
60.7
Socket-head screw DIN 912
max. 60.7
▼ 6-hole coupling flange, complete – ø 100
Material number: R902060153
ø99
2.3 7
48.2
42.5
ø8.5
ø84
M12 × 35 - 10.9
ø57
-0.046
0
60.7
Socket-head screw DIN 912
max. 60.7
Note
▶ Assembly of the coupling flange is carried out by pull-
ing onto the drive shaft with the aid of the threaded
bore in the drive shaft end.
▶ The coupling flange must be clamped on the drive
shaft using a socket-head screw. In addition, perma-
nent lubrication should be applied between the drive
shaft and the coupling flange.
▶ The socket-head screw should be secured in a suitable
manner (e.g. gluing with Loctite 276) and tightened
with a tightening torque of 130Nm.
▶ Sudden axial impact upon the drive shaft will lead to
rotary group damage and therefore must be avoided.
15
RE 91520/11.2015, Bosch Rexroth AG
Axial piston fixed pump | A17FO Series 10
Installation instructions
Installation instructions
General
During commissioning and operation, the axial piston unit
must be filled with hydraulic fluid and air bled. This must
also be observed following a long standstill as the axial
piston unit can empty via the hydraulic lines.
The pump housing is internally connected to the suction
chamber. A separate drain line from the housing to the
reservoir is not needed.
To achieve favorable noise values, decouple all connecting
lines using elastic elements and avoid above-reservoir
installation.
In all operating conditions, the suction line must flow into the
reservoir below the minimum fluid level. The permissible
suction height h
S
results from the overall loss of pressure.
However, it must not be higher than h
Smax
=800 mm. The
minimum suction pressure at port S must also not fall below
0.8bar absolute during operation and during cold start.
Installation position
See the following examples 1 to 4.
Further installation positions are available upon request.
Recommended installation position: 1 and 2.
Below-reservoir installation (standard)
Below-reservoir installation means that the axial piston unit
is installed outside of the reservoir below the minimum
fluid level.
Installation position Air bleed Filling
1
S
h
t min
h
min
R
R S
2
S
h
t min
h
min
R
– S
Above-reservoir installation
Above-reservoir installation means that the axial piston unit
is installed above the minimum fluid level of the reservoir.
Observe the maximum permissible suction height
h
Smax
=800mm.
Installation position Air bleed Filling
3
S
R
F
h
S max
h
t min
h
min
R F
4
S
R
h
S max
h
t min
h
min
S S
Key
F Filling/air bleed
R Air bleed port
S Suction port
h
t min
Minimum required immersion depth (200 mm)
h
min
Minimum required distance to reservoir bottom(100 mm)
h
S max
Maximum permissible suction height (800 mm)
Note
Port F is part of the external piping and must be provided
on the customer side to make filling and air bleeding
easier.
Other related documents
Other pumps with special characteristics and dimensions
for use in commercial vehicles can be found in the following
data sheets:
▶ 91510: Fixed pump A17FNO, 250/300 bar
▶ 92270: Variable pump, A18VO 350/400 bar
▶ 92280: Variable pump, A18VLO 350/400 bar
16
Bosch Rexroth AG, RE 91520/11.2015
Bosch Rexroth AG
Mobile Applications
Glockeraustraße 4
89275 Elchingen, Germany
Tel. +49 7308 82-0
info.ma@boschrexroth.de
www.boschrexroth.com
© This document, as well as the data, specifications and other information set
forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
reproduced or given to third parties without its consent. The data specified
above only serve to describe the product. No statements concerning a certain
condition or suitability for a certain application can be derived from our
information. The information given does not release the user from the
obligation of own judgement and verification. It must be remembered that our
products are subject to a natural process of wear and aging.
A17FO Series 10 | Axial piston fixed pump
Project planning notes
Project planning notes
▶ The A17FO pump is designed to be used in open circuits.
▶ The project planning, installation and commissioning of
the axial piston unit requires the involvement of quali-
fied personnel.
▶ Before using the axial piston unit, please read the corre-
sponding instruction manual completely and thoroughly. If
necessary, these can be requested from Bosch Rexroth.
▶ Before finalizing your design, please request a binding
installation drawing.
▶ The specified data and notes must be observed.
▶ Depending on the operating conditions of the axial
piston unit (operating pressure, fluid temperature), the
characteristic may shift.
▶ Preservation: Our axial piston units are supplied as
standard with protection to preserve for a maximum of
12 months. If longer preservative protection is required
(maximum 24 months), please specify this in plain text
when placing your order. The preservation periods apply
under optimal storage conditions, details of which can
be found in the data sheet 90312 or the instruction
manual.
▶ Not all variants of the product are approved for use in
safety functions according to ISO13849. Please consult
the responsible contact person at Bosch Rexroth if you
require reliability parameters (e.g. MTTF
d
) for functional
safety.
▶ Be sure to add a pressure relief valve to the hydraulic
system.
▶ Please note the details regarding the tightening torques
of port threads and other threaded joints.
▶ Working ports:
– The ports and fastening threads are designed for the
specified maximum pressure. The machine or system
manufacturer must ensure that the connecting ele-
ments and lines correspond to the specified applica-
tion conditions (pressure, flow, hydraulic fluid, tem-
perature) with the necessary safety factors.
– The service line ports and function ports can only be
used to accommodate hydraulic lines.
Safety instructions
▶ During and shortly after operation, there is a risk of
burns on the axial piston unit and especially on the
solenoids. Take appropriate safety measures (e.g.by
wearing protective clothing).