File: XEPV3_E 01/2010/eVIII • 13

INPUT SIGNAL CURVES - FLOW RATE

ORDERING CODE

The proportional directional valves XEPV are designed as direct operated components for

subplate mounting. They are actuated by means of proportional solenoids with central thread and

removable coil. The solenoids are controlled by integrated control electronics.

Features:

• Integrated control electronics

• Setup parameters by CAN interface

• Current compensation, gain current and ramps setting

• Monitoring of the valve by real time scope interface

XEPV.3... PROPORTIONAL VALVE WITH

ELECTRONIC ON BOARD

XEPV.3...

AM.3.H... CH. VIII PAGE 16

AM.5.H... CH. VIII PAGE 17

BC.3.07... CH. VII PAGE 12

XEPV Current loop proportional valve with

integrated electronics 24Vdc

3 CETOP 3/NG6

** Type of spool

01 =

spool with P, A, B

and T ports, closed

03 =

spool with P port closed,

and A, B, T ports connected

N Symmetrical flow control

* Flow rating at ∆p 8 bar

0 = 4 l/min

1 = 8 l/min

2 = 15 l/min

3 = 25 l/min

6 = 36 l/min (we advise to use

the hydrostat AM5H3VP108)

S CAN bus communication

S = standard ARON

* Command Enable

E = with external command Enable

W = without external command Enable

* Type command

V = signal voltage ± 10V

C = signal current 4... 20mA

00 No variants

1 Serial No.

(4 l/min P

→→

→ A/B) (8 l/min P

→ →

→ A/B)

European norms: EN 61000 - ElectroMagnetic

Compatibility (EMC) - industrial environment

(15 l/min P

→→

→ A/B) (25 l/min P

→ →

→ A/B)

(36 l/min P

→→

→ A/B)

XEPV.3.01.N...

XEPV.3.03.N...

a b

with

File: XEPV3_E 01/2010/eVIII • 14

OPERATING SPECIFICATIONS OF VALVE WITH TRANSDUCER

XEPV.3... P

ROPORTIONAL VALVE WITH ELECTRONIC ON BOARD

OVERALL DIMENSIONS

Support plane

specifications

1.6

0.03

Fixing screws UNI 5931

M5x25 (min. 8.8 material

screws are recommended)

Tightening torque 4 ÷ 5 Nm /

0.4 ÷ 0.5 kgm

Installation must keep horizontal

Max. operating pressure ports P/A/B 350 bar

Dynamic pressure port T 210 bar

Static pressure port T 210 bar

Nominal flow 4 / 8 / 15 / 25 / 36 l/min

Performance curves See diagrams

Fluid temperature -20 ÷ 75°C (preferably 40 ÷ 50°C)

Fluid viscosity 10 ÷ 500 mm

Max. contamination level class 7 to 9 in accordance to NAS 1638 with filter ß

≥75

Weight 2.45 kg

Nominal supply voltage 24Vdc

Input signal range (see ordering code) ± 10V or 4... 20mA

Supply voltage lower limit 18V

Supply voltage upper limit 36V

Peak power 50W

Max. coil temperature 150 °C

Duty cycle Continuous 100% ED

Hysteresis < 5%

Response sensitivity < 0.5%

Repeatibility <0.5%

Enable input command 0V = valve not active 24V = valve active

Fault signal output 0V = failure or not working valve 24V = valve OK

Current monitor ± 10V

Ambient temperature range -20 ÷ 60°C

Type of protection IP 65

Operating specifications are valid for fluids with 46 mm

/s viscosity at 40°C.

STEP RESPONSE (∆p = 8 bar P/A)

0 ÷ 100%

100% ÷ 0

File: XEPV3_E 01/2010/eVIII • 15

XEPV.3... PROPORTIONAL VALVE WITH ELECTRONIC ON BOARD

ELECTRICAL CONNECTIONS

Main

connector

7 ways

CAN bus

connector

5 ways

Enable - Fault

connector

5 ways

X2*: 5 ways M12 connector, CAN communication

(to be ordered separately)

Type PIN Description

1 CAN_H

CAN data 2 CAN_L

Aron interface 3

5 GND

* Connection cable recommended: up to 50m cable length type LiYCY

7x0.75 mm². For outside diameter see plug-in connector sketch.

Only connect screen to PE on the supply side.

X3*: 5 ways M12 connector, Enable and Fault digital command

(to be ordered separately)

Model: KVASER Leaf light HS

(not supplied, commercial parts)

The cable and D-Sub

connector are not

supplied. Assemble

the parts as shown in

the diagram.

ARON INTERFACE FOR SETUP PARAMETERS ADAPTER FOR PC: CABLE D-SUB TO CAN CONNECTOR

Aron Firetune software code: P35150005

For further information about Aron Firetune read the manual.

The software is included with valve supply.

ADAPTER FOR PC:

CABLE USB TO D-SUB

Cable D-SUB to

CAN connector

Cable USB

to D-SUB

ARON

Software

X1: Main connector 7 ways (supplied with the valve)

Type PIN Description

Main power supply A +24Vdc

B 0V / common supply

0V / common of signal monitor C 0V / common of signal monitor

Input of differential signal command D ± 10V or 4...20mA

E 0V / common

Output of signal monitor F ± 10V (10V = max current)

GND GND

Connection cable recommended: up to 50m cable length type LiYCY 7x1.0

mm². For outside diameter see plug-in connector sketch. Only connect

screen to PE on the supply side.

GND

DIN EN 175201-804 - 7 poles female

5 pole

connector

5 pole

connector

5 ways connector

code: VE0032700

5 ways connector

code: VE0032700

IEC 61076-2-101 - 5 poles female IEC 61076-2-101 - 5 poles female

Type PIN Description

Digital output signal 1 Connects to +24Vdc

of valve FAULT 2 Signal out:

0V = failure of electronic control

24V = valve OK

Input digital command 3 Connects to 0V

of ENABLE valve 4 Connects to +24V to enable the valve

ARON SOFTWARE AND CABLES

6 7 8 9

2 3 4 5

D-Sub connector

(female)

CAN connector

CAN-L

GND

CAN-H

CAN-L

GND

• A positive command value 0 to +10V (or 12 to 20mA) at D and the

reference potential at E, results in a flow from P to A and B to T.

• A negative command value 0 to -10V (or 12 to 4mA) at D and the

reference potential at E, results in a flow from P to B and A to T.