Functional Description

The RNEH solenoid operated - hydropiloted valves are

consisting of an RPE3-06 type solenoid operated

directional control valve (see data sheet HA 4010) that

operates a 4-way hydropiloted control valve with a

connection surface in accordance with the ISO 4401

standards. They are available in various configurations

and spool types.

The pilot and the drain connections can be made internal

or external by inserting or removing the accordant

threaded plugs located in the main directional control

valve.

A wide range of configurations and different solenoid

operated - hydropiloted directional control valve spool

positions are available:

– 4-way, 3-position directional control valve, with two

solenoids; positioning of the spool in center position is

obtained with centering springs.

– 4-way, 2-position directional valve, with one solenoid

and one return spring or two solenoids and detent of the

spool position.

The basic surface treatment of the valve housing is

phosphate coated and the solenoids are zinc coated.

HA 4023

7/2015

Replaces

HA 4023 9/2014

Size 16 (D 07) · 350/420 bar (5080/6090 PSI) · 300 L/min (80 GPM)

4/2 and 4/3 Way Directional

Control Valves Pilot Operated

RNEH5-16

Solenoid pilot operated directional valves (RNEH)

Hydraulic pilot operated directional valves (RNH)

Small energy input

Manual overrides optional

(only for RNEH)

Installation dimensions to DIN 24 340 /

ISO 4401 / CETOP RP121-H

HA 4023

Type of control

electrohydraulically operated

hydraulically operated H

Directional Control

Valve Pilot Operated

Valve size

Number of operating positions

two positions

three positions 3

Rated supply voltage of solenoids *

(at the coil terminals)

01200 12 V DC / 2.72 A

02400 24 V DC / 1.29 A

12060 120 V AC / 0.35 A / 50 (60) Hz

23050 230 V AC / 0.17 A / 50 (60) Hz

The AC coils correspond with E5 type.

* Other voltages per request.

Type of solenoid coil

E1 with terminal for the connector*

E2 with integrated quenching diode

and terminal for the connector*

E5 with integrated rectifier and terminal

for the connector*

Piloting

Internal no designation

External

Internal with pressure reducing valve Z

30 bar fix setting

Functional symbols

see the table functional symbols

Ordering Code

Note:

for spools H11 and C11 use check valve in P line – see option C3 page 7

Piloting must always be external for valves with the RNH type hydraulic control valve.

* from EN 1745301-803-A

Drain

no designation External

I Internal

Design series

standard 350 bar

high pressure version 420 bar

(5H is not available for spool C11)

Manual override

no designation Standard

N1 covered with retaining nut

N2 covered with rubber boot

Check valve incorporated in P-line

no designation if not required

C3 with check valve (see page 3)

see HA 4010 for other pilot valve options

Seals

no designation NBR

V FPM (Viton)

Controls

f not required no designation

main spool stroke limiter

main spool shifting speed control D

shifting speed control, with orifice (0.8 mm)

in port P of solenoid pilot valve

RN -16 / / / /

HA 4023

Technical Data

Valve type RN*5-16 RN*5H-16

Valve size mm (US) 16 (D 07)

Maximum flow rate from port P to A, B, T L/min (GPM ) 300 (80)

Max. operating pressure

ports P, A, B

- on line T with external drainage

- on line T with internal drainage)

bar (PSI)

350 (5800)

210 (3000)

140 (2030)

420 (6090)

350 (5800)

140 (2030)

Minimum pilot pressure bar (PSI 12 (174) 12 (174)

Maximum pilot pressure bar (PSI) 210 ( 3043)* 350 (5800)*

Pressure drop bar (PSI) see Pressure Drop Dp-Q

Hydraulic fluid Hydraulic oils of power classes (HL, HLP) to DIN 51524

Fluid temperature range for NBR seals °C (°F ) -30 ... +80 (-22 ... +176)

Fluid temperature range for FPM seals °C (°F ) -20 ... +80 (-4 ... +176)

Ambient temperature max. °C (°F ) +50 (+122)

Viscosity range mm

/s (SUS) 20 ... 400 (98 ... 1840)

Maximum degree of fluid contamination Class 21/18/15 to ISO 4406

Service life cycles 10

Enclosure type to EN 60529 IP 65

Weigt - RNH5-16

- RNEH5-162

- RNEH5-163

kg (Ibs)

6,6 (14.5)

8,2 (18)

8,8 (19.4)

*) for higher system pressure use option Z

Functional Symbols

Symbols are referred to the solenoid valve RNEH. For the hydraulic control version RNH please verify the connection

scheme (see page 7).

Three positions with spring centering Three positions with spring centering

Z11 H11

Y11 C11

Two positions with return spring Two positions with return spring

X11 R11

X21 R21

Two positions with mechanical detent on pilot valve

J15

J27

Besides the diagrams shown, which are the most frequently used, other special versions are available:

consult our technical department for their identification, feasibility and operating limits.

HA 4023

Dp-Q Characteristic Measured at n = 32 mm

/s (156 SUS) and t = 40 °C (104 °F)

200 250 300

(58)

(87)

(29)

(116)

(145)

100

150

(52.8)

(66.0)

(13.2) (39.6)(26.4) (79.3)

Pressure drop Dp [bar(PSI)]

200 250 300

100

150

(52.8)

(66.0)

(13.2) (39.6)(26.4) (79.3)

(58)

(87)

(24)

(174)

(203)

(116)

(145)

Spool type Spool position

P - A P - B A - T B - T P - T

Curves on graph

Z11 Energized 1 1 3 4

H11

Energized 1 1 4 4

De-energized 2

Y11

Energized 1 1 4 4

De-energized 4 4

C11

Energized 2 2 4 5

De-energized 4

R11, R21 1 1 3 4

X11, X21 1 1 4 4

J15, J27 1 1 3 4

200 250 300

100

150

(52.8)

(66.0)

(13.2) (39.6)(26.4) (79.3)

100

250

200

250

200

(1450)

(2176)

(725)

(4351)

(5076)

(2901)

(3626)

Q Characteristic Measured at n = 32 mm

/s (156 SUS) and t = 40 °C (104 °F)1

Spool type

P - A P - B

Curves on graph

Z11 1 1

H11 1 1

Y11 1 1

C11 2 2

R11, R21 1 1

X11, X21 1 1

J15, J27 1 1

Flow Q [L/min(GPM)]

p [bar(PSI)]

Operating limits

Check valve - Pressure Drop Dp-Q

This curve refers to the pressure drop (body part only)

with option C3 (check valve in P port). This pressure

drop must be added to the pressure drop of the

reference spool

Spool types - Pressure Drop Dp-Q

Flow Q [L/min(GPM)]

HA 4023

Electrical Features

DC solenoid AC solenoid

Max. allowable voltage variation % ±10 ±10

Max. switching frequency 1/h 10 000

Switching times ±10 %, energizing (two position) ms 70 60

Switching times ±10 %, de-energizing (two position) ms 80 80

Switching times ±10 %, energizing (three position) ms 50 80

Switching times ±10 %, de-energizing (three position) ms 60 60

Duty cycle % 100

Enclosure type to EN 60 529 IP 65

Solenoids

The operating solenoids are DC solenoids. For AC supply the solenoids are provided with rectifier which are integrated in the DIN

connector socket as part of the solenoid. The connectors can be turned by 90°. By loosening the nut, the solenoids can be turned

or replaced without interfering with any seals of the valve. In the case of solenoid malfunction or power failure, the spool of the

valve can be shifted by manual override, provided the pressure in T-port does not exceed 25 bar.

The values indicated refer to a solenoid valve operating with piloting pressure 100 bar, viscosity of 32 mm

/s and with

PA and BT connections. The switch on times are obtained from the time the spool switches over. The switch off times are

measured at the time pressure variation occurs in the line.

X: plug M6 x 8 for external pilot

Y: plug M6 x 8 for external drain

Pilot and Drain

Type of valve

Plug assembly

RNEH5-16**/*

Internal pilot and external drain NO YES

RNEH5-16**/*I

Internal pilot and internal drain NO NO

RNEH5-16**/*E

External pilot and external drain YES YES

RNEH5-16**/*EI

External pilot and internal drain YES NO

Check valve incorporated on line P: C3

Valve RNEH is available upon request with check valve incorporated on line P. This is

particularly useful to obtain the necessary piloting pressure when the main control

valve, in the rest position, has line P connected to the T outlet. The cracking pressure is

5 bar. Add C3 to the identification code for this request.

Special Configurations C3

Always without X plug

The RNEH valves are available with pilot and drain, both internal and external. The version with external drain allows

for a higher back pressure on the outlet

HA 4023

215 8.47()75 2.95()

45 [1.77]

97 [3.82]

154 [6.06]

125 [4.92]

184 [7.24]

201 [7.91]

3 [0.12]

4 [0.16]

92 [ ]3.62

50 [1.97]

40 [1.57]

190 [7.48]

12 [0.47]

Valve Dimensions Dimensions in millimeters (inches)

RNEH5-162, RNEH5-163

Single valve fastening: 4 bolts M10 x 60 *

2 bolts M6 x 60 *

Bolt torque: M10 x 60: 40 Nm (29.5 ft-lbs) - bolts A 8.8 67 Nm(49.5 ft-lbs) - bolts A 12.9

M6 x 60: 8 Nm (5.9 ft-lbs) - bolts A 8.8 14 Nm(10.3 ft-lbs) - bolts A 12.9

Threads of mounting holes: M6 x 18; M10 x 18

Seal rings: 4 O-rings type 22.22 x 2.62

2 O-rings type 10.82 x 1.78

1 Mounting surface with seal rings

2 Manual override

3 Space required to remove coil

4 Electrical connector

(must be ordered separately)

5 Space required to remove connector

Required surface finish of

interface

* Bolts is not supplied

HA 4023

Type of Command

90 (3.54)

17 (0.67)

215 (8.46)

230 controls or pilotting

270 for both - option

D+Z

(9.05) for

(10.63)

Solenoid control: RNEH

The valve is supplied with a pilot solenoid valve type RPE3-06.

Controls and pilotting

Control of the main spool shifting speed: D

By placing a 2VS3-06 type double flow control valve

between the pilot solenoid valve and the hydropiloted valve,

the piloted flow rate can be controlled and therefore the

shifting speed can be varied. Add the letter D to the

identification code to request this device.

Hydraulic control: RNH

The valve is supplied with a cross-connection

cover-plate.

X and Y connections are used for the hydraulic control

of the valve.

RNH5-163

RNH5-162R*

RNH5-162X*

RNEH5

RNH5

Main spool stroke limiter: C

Stroke limiters reduce flow through the valve.

190 (7.48)

319 (12.56)

Pilot pressure reducing valve - 30 bar fix setting: Z

Instead of option D or together with option D can be used

option Z.

Manual Override

Whenever the solenoid valve installation may involve exposure to atmospheric agents or be used in tropical climates,

the manual override, boot protection is recommended. Add the suffix N1 or N2 to request this device.

Electrical Connector

The solenoid valves are never supplied with connector. Connectors must be ordered separately.

HA 4023

Installation

Configurations with centering and recall springs can be mounted in any position; type J17, J27 valves - without springs and

with mechanical retention must be mounted with the longitudinal axis horizontal. Valve fastening takes place by means of

screws or tie rods, placing the valve on a flat surface, with values of planarity and smoothness that are equal to or better

than those indicated in the drawing. If the minimum values of planarity or smoothness are not met, fluid leakages between

valve and mounting surface can easily occur.



Service valve without range stated parameter consultation with manufacturer.



Detaile information at control vavle - see data sheet RPE3-06, HA 4010



The packing foil is recyclable.



The protective plate can be returned to manufacturer.



The technical information regarding the product presented in this data sheet is for descriptive purposes only. It should

not be construed in any case as a guaranteed representation of the product properties in the sense of the law.

Spare Parts

Seal kit

Design

Dimensions, number

Ordering

number

O-ring Square ring Back-up ring

Head valve

size 16 (D 07)

Standard - NBR

22.22 x 2.62 (4 pcs.)

3254970010.82 x 1.78 (2 pcs.)

37.69 x 3.53 (2 pcs.)

Viton

22.22 x 2.62 (4 pcs.)

3254980010.82 x 1.78 (2 pcs.)

37.69 x 3.53 (2 pcs.)

Throttle valve

2VS3-06-CS

type number

15929600

Standard - NBR

18 x 2.65 (2 pcs.) 9.25 x 1.68 (4 pcs.) 6.73 x 9.43 x 1.14 (2 pcs.)

15936300

6.9 x 1.8 (2 pcs.)

17.83 x 22.19 x 1.14 (2 pcs.)

Viton

17.12 x 2.62 (2 pcs.) 9.43 x 6.73 x 1.14 (2 pcs.)

159366009.25 x 1.78 (4 pcs.) 17.83 x 22.19 x 1.14 (2 pcs.)

6.75 x 1.78 (2 pcs.) -

Control valve see data sheet ARGO-HYTOS - HA 4010 - RPE3-06

Mounting bolt

Dimensions, number Tightening torque

Ordering

number

Fixation of

extension

of valve

Bolt M5 x 45

DIN 912-10.9

(4pcs.)

8.9 Nm

(6.6 ft-lbs)

15845100

Bolt M5 x 98 - 8G

(4 pcs.) 16103700

Nut M5

Other

Design

Cover plate

PA, BT 15934200

PB, TA 15933700

Caution!

Subject to alteration without notice!

ARGO-HYTOS s.r.o. CZ - 543 15 Vrchlabí

Tel.: +420-499-403 111

E-mail: info.cz@argo-hytos.com