1
Functional Description
The RPE3 directional control valves consist of housing
(1), a control spool (5) with two centering springs (4) and
cylindrical operating solenoids (2, 3).
The three-position directional control valves are fitted
with two solenoids and two springs. Two-position
directional control valves have either one solenoid and
one return spring or two solenoids and a detent
assembly.
The operating solenoids are DC solenoids. For AC
supply the solenoids are provided with a rectifiers which
are integrated in the DIN connector socket as part of the
solenoid. The connectors (6, 7) can be turned by 90°. By
loosening the nut (8), the solenoids can be turned or
replaced without interfering with any seals of the valve.
In the case of solenoid malfunction or power failure, the
spool of the valve can be shifted by manual override (9),
provided the pressure in T-port does not exceed 25 bar.
The valve housing (1) is phosphate coated and the
solenoids (2, 3) are zinc coated.
a
b
A B
AB
P
T
HA 4010
11/2011
Directional Control Valves
Solenoid Operated
RPE3-06
Replaces
HA 4010 12/2009
q
4/3-, 4/2- way directional control valves
q
Solenoids can be turned around their axis
to any position
q
Four-land spool - reduced functional dependence
on fluid viscosity
q
Push button manual override
q
Installation dimensions to DIN 24 340 /
ISO 4401 / CETOP RP121-H
q
Subplates see data sheet HA 0002
q
CSA Upon request
Size D 06 (03) ·350 bar (5076 PSI) · 80 L/min(21 GPM)
Size D 06 (03) • p
max
320 bar (4641PSI) according to CSA 80 L/min(21 GPM)
2
HA 4010
Ordering Code
Note: Connector of the position sensor is not supplied
(see ordering number on page 10)
RPE3-06 /
Spool symbols
see the table spool symbols
Valve size
Directional Control
Valves Solenoid
Operated
Number of valve positions
two positions
2
three positions 3
Seals
no designation NBR
V FPM (Viton)
Orifice in P port
no designation without orifice
D1 Æ1.0 mm (0.039 inch)
D2 Æ1.5 mm (0.059 inch)
D3 Æ2.0 mm (0.079 inch)
D4 Æ2.2 mm (0.087 inch)
D5 Æ2.5 mm (0.098 inch)
Soft Shift -
Spool speed control orifice
no designation without damping
T1 orifice Æ 0.7 mm (0.03 inch) in solenoid
Manual overide
no designation Standard
N1 covered with retaining nut
N2 covered with rubber boot
N3 with detent assembly
CSA Upon request
Sensing of the end position
no designation without sensor
S1 normally-open sensor to 50 bar
(725PSI)
S2 normally-open sensor to 210bar
(3045 PSI)
S4 normally-closed sensor to 50bar
(725 PSI)
Other coils on demand see catalog HA8007
Type of solenoid coil
with terminal for the connector, EN 1745301-803
E1
with integrated quenching diode and terminal E2
for the connector, EN 1745301-803
with AMP-Junior-Timer-connector
E3A
with integrated quenching diode and terminal E4A
for AMP-Junior-Timer connector
with integrated rectifier and terminal
E5
for the connector, EN 1745301-803
FOR PREFERRED TYPES SEE BOLD TYPING IN ORDERING CODE, FUNCTIONAL SYMBOLS
AND TABLE OF PREFERRED TYPES ON PAGE 10
Rated supply voltage of solenoids
(at the coil terminals)
12 V DC / 2.72 A
01200
24 V DC / 1.29 A 02400
205 V DC / 0.15 A 20500
230 V AC / 0.17 A / 50 (60) Hz 23050
The AC coils correspond with E5 type
3
HA 4010
Type Symbol Crossover Type Symbol Crossover
Technical Data
Valve size mm (US) D 06 (03)
Maximum flow L/min (GPM) see p-Q characteristics
Max. operating pressure at porte P, A, B bar (PSI) standard 350 (5076), according to CSA
320 bar (4641PSI)
Max. operating pressure at port T bar (PSI)
50 (725) for version S1, S4
and 210 (3000) for version S2
Pressure drop bar (PSI) see Dp-Q characteristics
Hydraulic fluid Hydraulic oils of power classes (HL, HLP) to DIN 51524
Fluid temperature range for NBR seals °C (°F) -30 ... +80 (-22 ... +176)
Fluid temperature range for FPM seals °C (°F) -20 ... +80 (-4 ... +176)
Ambient temperature max. °C (°F) +50 (+122)
Viscosity range mm
2
/s (SUS) 20 ... 400 (98 ... 1840)
Maximum degree of fluid contamination Class 21/18/15 to ISO 4406
Max. allowable voltage variation % DC: ±10 AC: ±10
Max. switching frequency h
-1
15 000
Switching time, on: at n=32 mm
2
.s
-1
(156 SUS) ms DC: 30 ... 50 AC: 30 ... 40
Switching time, off: at n=32 mm
2
.s
-1
(156 SUS) ms DC: 10 ... 50 AC: 30 ... 70
Duty cycle % 100
Service life cycles 10
7
Enclosure type to EN 60 529 IP 65
Weigt - valve with 1 solenoid
- valve with 2 solenoids
kg (lbs)
1.6 (3.52)
2.2 (4.84)
Mounting position unrestricted
Spool Symbols
4
HA 4010
p-Q Characteristics Measured at n = 32 mm
2
/s (156 SUS)
Operating limits for maximum hydraulic power transferred by the directional valve.
For respective spool type - see spool symbols.
Z11 1
C11 7
H11 4
P11 1
Y11 3
L21 6
B11 9
Y41 7
Z21 1
C41 6
F11 6
R11 4
R21 5
A51 6
P51 1
Y51 3
C51 7
Z51 1
Z71 8
Z81 8
Z91 8
R31 6
H51 8
F51 8
X11 4
K11 8
N11 8
X25 11
J15 1
J75 10
Dp-Q Characteristics Measured at n = 32 mm
2
/s (156 SUS)
Pressure drop Dp related to flow rate.
Pressure drop Dp [bar (PSI)]
P-A P-B A-T B-T P-T
Z112233
C1155563
H1122233
P111133
Y112222
L212233
B112233
Y413333
Z21 2 3
C41 4 4 5
F1112 33
R112233
R212233
A51 2 2
P51 1 3
Y51 2 2
C51 2 3 4
Z51 2 3
Z71 3 3
Z81 3 3
Z91 3 3 3
R31 2 3
H51 2 3
F51 2 3
X112233
K11 2 3
N112233
X25 3 3 3
J152233
J75 2 2
Operating pressure p [bar (PSI)]
Flow Q [L/min (GPM)]
Flow Q [L/min (GPM)]
5
HA 4010
Valve Dimensions Dimensions in milimeters (inches)
12,5 (0.492)
21,5 (0.846)
12,7 (0.512)
30,2 (1.189)
33 (1.231)
40,5 (1.594)
68 (2.677)
52 (2.047)
215 (8.465)
73,5 (2.894)
5,1 (0.201)
0,75 (0.030)
15,5 (0.610)
25,9 (1.019)
31 (1.220)
7 (0.276)
A
B
P
T
3 (0.12)
1,25 (0.049)
45,5 (1.791)
32,5 (1.280)
1,4 (0.055)
P
149,5 (5.886)
Æ
9,5 (0.374)
Æ
5,3 (0.209)
Æ
8 (0.315)
Æ
12,4 (0.488)
56,5 (2.224)
Æ
45 (1.772)
92,5 (3.641)
ab
24 (0.945)
37,3 (1.468)
49,3 (1.940)
a
8 (0.315)
b
P
P
12 (0.472)
Valve with two solenoids
Valve with one solenoid "a"
Spool symbols R11, R21, A51, P51,
Y51, Z51, C51, Z71, Z81, Z91,
R31, H51, F51, X25
Valve with one solenoid "b"
Spool symbols X11, Z11, C11, H11,
K11, N11, F11
1 Solenoid a
2 Solenoid b
3 Manual override
4 Name plate
5 Square ring (4 pcs.)
9.25 x 1.68 supplied with valve
6 4 mounting holes
7 Electrical connecto, EN 1745301-803
8 Space required to remove connector
9 Solenoid fixing nut
[Nut torque 2.95 ft-lbs (4 Nm)]
[
[
[
[
in
mm
0,8(32)
Rmax 6,3(248) ([]mm
m in)
0.01 / 100
0.0004 / 4.0
Required surface finish of
interface
6
8
7
4
3 1 5 2 9 3
6
HA 4010
38 (1.259)
45 (1.772)
a
32 (1.259)
a
Type of the Solenoid Coil
Designation Dimensional sketch Description
E1
Solenoid coil with terminal for the electrical
connector, EN 1745301-803.
E2
Solenoid coil with integrated quenching diode
(bipolar transil diode) and terminal for the
electrical connector, EN 1745301-803.
E3A
Solenoid coil with terminal for
AMP-Junior-Timer electrical connector.
E4A
Solenoid coil with integrated quenching diode
(bipolar transil diode) and terminal for
AMP-Junior-Timer electrical connector.
E5
Solenoid coil with integrated rectifier and
terminal for the electrical connector,
EN 1745301-803.
Manual Override
STANDARD CLOSED NUT
no designation
Dimensions
Standard model of the manual override.
Standard retaining nut of the solenoid.
Type N1
Dimensions
Manual override with retaining nut.
Can be used after removing nut.
RUBBER BOOT DETENT ASSEMBLY
Type
N2
Dimensions
Manual override protected by rubber boot.
Type
N3
Dimensions
Manual override holds the spool in the shiftet position.
7
HA 4010
Spool Speed Control Orifice
Type Dimension Description
T1
Important: This directional valve provides control spool
soft shifting by means of orifice situated in the solenoid
armature.To ensure the proper function of the valve,
perfect air bleeding of the solenoid is required (by us of
bleeding plug (1). The plugs are accessible after
removing the rubber boot (2) from the solenoid retaining
nut (3).
Switching times
Switching time, on and off ms 300 ... 800
The switching times shown are valid for viscosity n = 32 mm
2
/s (156 SUS) and nominal
voltage. They are dependent upon working pressure and flow rate of the directional control valve
2
1
3
Orifice in P-Port
Type ÆD mm (inch) Dimensions Description
D1
1,0 (0.039)
P-port orifices limit the flow into the directional
control valve.
Attention:
When the orifice in P port is additionally
mounted the standard used square ring NBR
is replaced with O-ring from Viton.
D2
1,5 (0.059)
D3
2,0 (0.079)
D4
2,0 (0.087)
D5
2,0 (0.098)
Seal ring
8
HA 4010
aSaSbb
a (b)
Sa (Sb)
Connector
Spool Ship Position Sensor
S1, S2 - Circuit diagram of the
normally-open sensor
S4 - Circuit diagram of the
normally-closed sensor
2
PNP Sensor PNP Sensor
Connector
The proximity sensor transforms
the spool position into an
electrical step signal. It can be
used with directional control
valves with one or two solenoids.
Technical Data of the Connector
Power supply voltage range V 10 ... 30 DC
Ambient temperature range °C (°F) -25 ... +80 (-13 ... +176)
Indication yellow LED
Two-Position Directional Control Valve Dimensions in millimeters (inches)
Signal of solenoid a (b) Signal of sensor Sa (Sb) LED
S1, S2 - normally-open S4 - normally-closed S1, S2 S4
0 1 0 ON OFF
1 0 1 OFF ON
Technical Data of the Sensor S1, S4 S2
Rated power supply voltage V 24 DC
Power supply voltage range V 10 ... 30 DC
Rated current mA 200
Enclosure type of sensor to EN 60529 IP 67
Max. operating pressure bar (PSI) 50 (725) 210 (3046)
Switching frequency Hz 1000
Ambient temperature range °C (°F) -25 ... +80 (-13 ... +176)
Three-Position Directional Control Valve Dimensions in millimeters (inches)
Signal of solenoid Signal of sensor Sa (Sb) LED
S1, S2 - normally-open S4 - normally-closed S1, S2 S4
a b Sa Sb Sa Sb Sa - LED Sb - LED Sa - LED Sb - LED
0 0 1 1 0 0 ON ON OFF OFF
1 0 0 1 1 0 OFF ON ON OFF
9
HA 4010
Solenoid coil
Solenoid type
Coil type
E1 E2 E3A E4A E5
Order number
01200 16211400 24156100 24159600 24159700
01200* 24154300 - - -
02400 - 24157400 24159800 24159900
02400* 24154400
20500 -
23500 18849000
23500* 24154600
Solenoid retaining nut with seal
Type of the nut Seal ring Order number
Standard nut
22 x 2
15844600
Closed nut 15844700
Nut with rubber boot 15844800
Nut with detent assembly 15844900
Connector of position sensor
Type designation Model Max. input voltage Ordering number
K02 connector of position sensor with LED 10...30 V DC 17364800
S1 normally-open sensor 10...30 V DC 16688500
S2 normally-open sensor 10...30 V DC 18961900
S4 normally-closed sensor 10...30 V DC 20725300
Orifice in P-port
Type ÆD mm (inch) Seal ring Order number
D1 1,0 (0.039)
9.25 x 1.75
15845600
D2 1,5 (0.059) 15845700
D3 2,0 (0.079) 15845800
D4 2,2 (0.087) 15846000
D5 2,5 (0.098) 15845900
Bolt kit
Dimensions, quantity Bolt torque Order number
M5 x 45 DIN 912-10.9 (4 pcs.) 8.9 Nm (6.6 ft-Ibs) 15845100
Seal kit
Type Dimensions, quantity Order number
Standard - NBR70 9,25 x 1,68 x 1,68 (4 pcs.) 17 x 1.8 (2 pcs.) 15845200
Viton 9,25 x 1,78 (4 pcs.) 17,17 x 1,78 (2 pcs.) 15845400
Spare Parts
1 Electrical connector
2 Solenoid coil
3 Nut with seal
4 Orifice in P port with seal ring
5 Sensor
6 Connector of position sensor with LED
7 Seal kit
8 Mounting bolts
a
b
1
2
1
5
6
3
7
4
8
AB
P
A
B
T
2
*CSA Upon request
10 Subject to alteration without notice!
HA 4010
Electrical connector, EN 1745301-803
Type
Connector A grey Connector B black
Ordering number
K1 16202200 16202100
K5 16202600 16202500
K2 16202800 16202700
K3
16202400 16202300
K4 16203000 16202900
Caution!
ARGO-HYTOS s.r.o. CZ - 543 15 Vrchlabí
Tel.: +420-499-403 111
E-mail: info.cz@argo-hytos.com
www.argo-hytos.com
Recommended solenoid coils used with electrcial connector with rectifiers - type designation K3, K4
Rated supply source voltage
(permissible rated voltage variation ±10 %)
Type designation of the solenoid voltage
230 V AC / 0.17 A / 50 (60) Hz 20500
Preferred Types of Valves
Type Ordering Number Type Ordering Number
RPE3-062Z11/01200E1 15720300 RPE3-063Y11/02400E1 15728400
RPE3-063Z11/01200E1 15711300 RPE3-062R11/02400E1 15731100
RPE3-062Z51/01200E1 15719300 RPE3-062R21/02400E1 15734500
RPE3-063C11/01200E1 15712600 RPE3-062A51/02400E1 15732800
RPE3-062C51/01200E1 15719600 RPE3-062Y51/02400E1 15737400
RPE3-063H11/01200E1 15713500 RPE3-062J15/02400E1 15733500
RPE3-063Y11/01200E1 15714300 RPE3-062Z11/23050E5 15768800
RPE3-062R11/01200E1 15716000 RPE3-063Z11/23050E5 15747100
RPE3-062R21/01200E1 15717100 RPE3-062Z51/23050E5 21262800
RPE3-062A51/01200E1 15716700 RPE3-063C11/23050E5 15748900
When the distributor contains two electromagnets any of the two electromagnets can be switched on only after the
other one switches off. The electromagnets switching time on distributors with locking arrangement must not be
shorter than 60 ms.With directional valves with cushioned spool shifting, the switching time must correspond
with the shifting time.
Distributors with other interconnections than those shown in the catalogue can be supplied on request.
The packaging foil can be recycled
The transport base plate can be returned to the manufacturer.
Mounting screws M5 x 45 DIN 912-10.9 or bolts must be ordered separately.
The screws tightening torque is 8.9 Nm (6.6 ft-Ibs).
The mentioned data only serve to describe the product and in no case are to be understood in terms of law as
guaranteed characteristics.
Electrical Connector, EN 175301-803
K1
Connector B (black)
without rectifier - M16x1.5
( bushing bore Æ 6-8 mm)
230 V AC/DC
Connector A (grey)
K5
Connector B (black)
without rectifier - M16x1.5
( bushing bore Æ 4-6 mm)
230 V AC/DC
Connector A (grey)
K2
Connector B (black) without rectifier with LED
and quenching diode - M16x1.5
( bushing bore Æ 6-8 mm)
12 ... 24 V DC
Connector A (grey)
K3
Connector B (black)
with rectifier - M16x1.5
( bushing bore Æ 6-8 mm)
230 V AC
Connector A (grey)
K4 Connector B (black)
with rectifier with LED
and quenching diode - M16x1.5
( bushing bore Æ 6-8 mm)
230 V AC
